NuTone ICA-441WHW User Manual
MOUNTING
Refer to Figure 6.
1. Carefully place excess wire into mounting frame.
2. Place gasket (furnished) into groove of mounting frame. Leave a
small gap at the bottom center. Place edge of the remote control
into the groove of the frame. Make sure the control and frame fit
together tightly.
3. Secure remote control to frame with two (2) mounting screws
(furnished).
IMPORTANT – WHEN NUTONE MODEL IW-6R
WIRING IS USED:
CONNECT TO SCREWS ON PRINTED
CIRCUIT BOARD MARKED:
BLUE STRIPE
1 ORN
2 BLK
3 BLK/WHITE
4 ORN/WHITE
5 RED
6 RED/WHITE
READ & SAVE THESE INSTRUCTIONS!
INSTALLATION INSTRUCTIONS
Outdoor Remote Control
MODEL: ICA-441WHW
• This model is designed for outdoor use only with
IMA4406, IM4406, IMA4006 or IM4006 Systems to
operate the ISA-77, IS-79 or IS-903 Outdoor Speakers.
• Use Model ICA-441WH for indoor installation.
LOCATION
1. Locate the remote control near the speaker which it will control.
2. Locate the remote control where it can be easily
operated – 50˝ to 60˝ above the floor or ground is satisfactory.
FRAME WIRING
Refer to Figure 1.
1. Run NuTone Model IW-6 intercom wire from master station to
location of frame.
2. Run 2-conductor wire (IW-2) from remote control location to
speaker location.
3. Pull wires through hole in back of frame.
IMPORTANT: Use only NuTone specified wire.
FRAME MOUNTING
The frame must be mounted in horizontal position, as shown in
Figure 1.
1. Nail or screw frame to finished wall surface through four (4)
mounting holes.
2. Frame should be caulked around edge which is flush to wall.
WIRING CONNECTIONS
1. Refer to Figure 2. Remove plastic clip that holds the rubber
gasket to the printed circuit board.
2. Refer to Figure 3. As illustrated, connect wires from the master
unit to the six (6) screw terminals. Red wire to the terminal marked
red, red/white wire to the terminal marked red/white, etc.
3. Refer to Figure 4. Connect IW-2 cable from the speaker to the
remote control's two (2) speaker wires.
4. Refer to Figure 5. Fold rubber gasket over installed wiring. Hold
gasket tab to printed circuit board by folding tab over and sliding
the removed plastic clip over tab and printed circuit board.
FIGURE 1
FIGURE 2
FIGURE 3
IW-6
CABLE
MOUNTING FRAME
MUST BE MOUNTED
IN HORIZONTAL
POSITION
IW-2
CABLE
RED
RED/WHITE
BLACK
BLACK/WHITE
ORANGE/WHITE
ICA-441WHW
PRINTED
CIRCUIT
BOARD
PLASTIC CLIP
GASKET TAB
ORANGE
Product specifications subject to change without notice.
4820 Red Bank Road, Cincinnati, Ohio 45227
Printed in China, Rev. 08/06, Part No. 61434
NuTone
INSIDE/PATIO
TALK
DOOR
TALK
END
CALL
AM/FM/CD
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
VOLUME
PRIVATE
OFF ON
•
•
•
FIGURE 4
FIGURE 5
FIGURE 6
ICA-441WHW
CIRCUIT
BOARD
IW-2 CABLE
TO
SPEAKER
RUBBER
GASKET
IW-6 CABLE
GASKET TAB
PLASTIC CLIP
ICA-441WHW
PRINTED
CIRCUIT
BOARD
MAKE SURE GASKET IS
COMPLETELY AGAINST
OUTSIDE RIM AND PUSHED
INTO THE GROOVE
IW-6 CABLE
ICA-441WHW
OUTDOOR
REMOTE
CONTROL
PLACE GASKET
IN GROOVE IN
MOUNTING FRAME.
LEAVE GAP
BETWEEN ENDS OF
GASKET AT THE
BOTTOM CENTER
IW-2 CABLE
MOUNTING
FRAME
Refer to the Radio-Intercom system's Operator's Manual
for operating instructions. If Operator's Manual has been
misplaced, write to:
NuTone
4820 Red Bank Road
Cincinnati,Ohio 45227
Attention: Department of National Field Service
CONTROL
Loading...