Numark M101 Quick Start Guide [ml]

 QUICKSTART GUIDE

ENGLISH ( 3 – 5 )

 MANUAL DE INICIO RÁPIDO

ESPAÑOL ( 6 – 8 )

 GUIDE D’UTILISATION RAPIDE

FRANÇAIS ( 9 – 11 )

 GUIDA RAPIDA

ITALIANO ( 12 – 14 )

 KURZANLEITUNG

DEUTSCH ( 15 – 17 )

BOX CONTENTS

 M101
 AC Power Adapter
 Quickstart Guide
 Safety & Warranty Information Booklet

REGISTRATION

Please go to http://www.numark.com to register your M101. Registering your product ensures that we can keep you up-to-date
with any last-minute product developments and provide you with world-class technical support, should you run into any
problems.

GROUND RULES

1. Make sure all items listed in the BOX CONTENTS section are included in the box.

2. READ SAFETY & WARRANTY INFORMATION BOOKLET BEFORE USING THE PRODUCT.

3. Study the connection diagram in this guide.

4. Place mixer in an appropriate position for operation.

5. Make sure all devices are turned off and all faders and gain knobs are set to “zero.”

6. Connect all stereo input sources as indicated in the diagram.

7. Connect the stereo outputs to power amplifier(s), tape decks, and/or other audio sources.

8. Plug all devices into AC power.

9. Switch everything on in the following order:

• Audio input sources (i.e. turntables, CD players, etc.)

• Mixer

• Last, any amplifiers or output devices

10. When turning off, always reverse this operation by:

• Turning off amplifiers

• Mixer

• Last, any input devices

CONNECTION DIAGRAM

TURNTABLE

TURNTABLE

HEADPHONES

POWER

HOUSE AMP

MICROPHONE

CD PLAYER CD PLAYER

3

REAR PANEL FEATURES

1. POWER SWITCH – Turns the mixer on and off.

Turn on the mixer after all input devices have been
connected and before you turn on amplifiers. Turn
off amplifiers before you turn off the mixer.

2. AC IN – Use the included power adapter to

connect the mixer to a power outlet. While the
power is switched off, plug the power supply into
the mixer first, then plug the power supply into a
power outlet.

Note: The mixer is designed to work with the
included power supply only. Using an incompatible
power supply could result in damage to the unit.

3. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier system. The

level of this output is controlled by the MASTER knob on the top panel.

4. LINE INPUTS (RCA) – Connect line-level devices, such as CD players, samplers or audio interfaces, to these inputs.

5. PHONO INPUTS (RCA) – Connect phono-level devices, such as turntables, to these inputs.

6. GROUNDING TERMINAL – If you are using phono-level turntables with a grounding wire, connect the grounding wire to

these terminals. If you experience a low “hum” or “buzz”, this could mean that your turntables are not grounded.

Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be
connected to the grounding terminal.

TOP PANEL FEATURES

1. POWER LED – Illuminates when the mixer is on.

2. STEREO LEVEL INDICATOR – Displays the audio

level of the Program mix.

3. MASTER – This control adjusts the output volume of the

Program mix.

4. MIC GAIN – Adjusts the audio level of the microphone

signal.

5. MIC TREBLE – Adjusts the high (treble) frequencies of

the microphone channel.

Tip: If you experience feedback when using a
microphone at loud levels, try turning down the high
frequencies.

6. MIC BASS – Adjusts the low (bass) frequencies of the

microphone channel.

7. CUE GAIN – Adjusts the level of the headphone audio.

8. CUE MIX – Turn to mix between Channels 1 and 2 in

the headphones. When all the way to the left, only
Channel 1 will be heard. When all the way right, only
Channel 2 will be heard.

9. CHANNEL GAIN – Adjusts the corresponding channel’s

pre-fader and pre-EQ gain level.

10. CHANNEL TREBLE – Adjusts the high (treble)

frequencies of the audio on the corresponding channel.

11. CHANNEL BASS – Adjusts the low (bass) frequencies

of the audio on the corresponding channel.

12. INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks are located on the

rear panel.

13. CHANNEL FADER – Adjusts the audio level on the corresponding channel.

14. CROSSFADER – Blends audio playing between Channels 1 and 2. Sliding this to the left plays channel 1 and sliding to

the right plays Channel 2.

Note: The crossfader is user-replaceable if it should ever wear out. Simply remove the facepanel, then remove the
screws holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer
only.

15. MIC INPUT – Connect ¼” microphones to this input. The microphone controls are located on the top panel.

16. HEADPHONES – Connect your ¼” headphones to this output for cueing and mix monitoring.

1

334

2

49

5

10

6

11

4

1

2

12 12

13

14

15 16

5

5

9

10

11

13

6

4

5

4

5

3

7

8

4

A

A

A

CONTENIDO DE LA CAJA

 M101
 Adaptador de CA
 Guía de inicio rápido
 Folleto de información sobre la seguridad y la garantía

REGISTRO

Visite http://www.numark.com y registre su M101. El registro de su producto asegura que podamos mantenerle actualizado
con los desarrollos de productos de último momento y brindarle apoyo técnico de categoría mundial en caso de que tenga
algún problema.

REGLAS BÁSICAS

1. Asegúrese de que todos los artículos indicados en “Contenido de la caja" estén incluidos en la caja.

2. LEA EL FOLLETO DE INFORMACIÓN SOBRE LA SEGURIDAD Y LA GARANTÍA ANTES DE UTILIZAR EL
PRODUCTO.

3. Estudie el diagrama de conexión incluido en esta guía.

4. Coloque el mezclador en una posición adecuada para su funcionamiento.

5. Asegúrese que todos los dispositivos estén apagados y que todos los faders y perillas de ganancia estén en posición
«cero».

6. Conecte todas las fuentes de entrada estéreo como se indica en el diagrama.

7. Conecte las salidas estéreo a los amplificadores de potencia, bandejas de cinta magnética y/o otras fuentes de audio.

8. Enchufe todos los dispositivos al suministro de corriente alterna.

9. Encienda todo en el siguiente orden:

• fuentes de entrada de audio (por ejemplo, giradiscos, reproductores de CD, etc.)

• el mezclador

• por último, cualquier amplificador o dispositivo de salida

10. Al apagar, realice siempre esta operación en sentido inverso:

• apague los amplificadores

• el mezclador

• por último, cualquier dispositivo de entrada

DIAGRAMA DE CONEXIÓN

GIRADISCOS

URICULARES

GIRADISCOS

MICRÓFONO

LIMENTACIÓN

MPLIFICADOR DE AUDITORIO

REPRODUCTORS DE CD

5