Numark DJ|iO Quick Start Manual

QUICKSTART GUIDE

ENGLISH ( 2 – 7 )

GUÍA DE INICIO RÁPIDO

ESPAÑOL ( 8 – 13 )

GUIDE D'UTILISATION SIMPLIFIÉ

FRANÇAIS ( 14 – 19 )

ITALIANO ( 20 – 25 )

KURZANLEITUNG

DEUTSCH ( 26 – 31 )

GUIDA RAPIDA

BOX CONTENTS

DJ|iO Quickstart Guide
USB Cable Safety Instructions & Warranty Information booklet
CD

FEATURES

1. USB PORT – Please use the supplied

USB2.0 cable to connect this port to an
available USB2.0 port on your computer.
When plugged into your computer, the unit
will draw power from the USB connection.

Please note: The DJ|iO requires a USB2.0
connection in order to function fully and
properly. If using a USB1.1 connection, only
OUTPUT 1 will work. To take advantage of
both outputs, please make sure that you are
connecting to a USB2.0 compatible port on
your computer.

2. DC IN – If your computer does not supply

enough power through the USB bus, you
may wish to power the unit externally by
connecting an optional 6V/1A adapter to this input and plugging the adapter into a power supply.

3. OUTPUT 1 – This stereo RCA connection will output the Master Mix from your computer. Please use a
stereo RCA cable to connect this output to a powered speaker or amplifier system.

4. OUTPUT 2 – This stereo RCA connection will output the Cue Mix from your computer for monitoring
purposes. Please note that the Cue Mix is also output through the Headphone Output on the front panel.

5. POWER INDICATOR – This LED will light up to let you know that the DJ|iO is on.

6. MIC THROUGH INPUT – This is a ¼" microphone input. The signal from this input will be sent directly to
the Output 1 (Master Mix) RCA output.

7. MIC VOL – This knob controls the microphone level being sent to Output 1 (Master Mix).

8. HEADPHONES – This stereo ¼" output will output the signal being routed to Output 2 (Cue Mix). To take
full advantage of cueing and monitoring through this output, please make sure that you have routed the
Cue Mix in your software to Output 2 of the DJ|iO.

5

33

7

6

44

8

12

2

CONNECTION DIAGRAM

Be sure your audio software
program is set up to receive audio
via the DJ|iO. This can usually be
done in your software's
"Preferences" or "Device Setup."
Please consult your software
manual for more information.

MICROPHONE HEADPHONES COMPUTER

SPEAKER OR AMP

SYSTEM (MASTER)

POWER

SPEAKER OR AMP

SYSTEM (MONITOR)

3

INSTALL THE DRIVERS

PC

Before you can begin using the DJ|iO with your computer, you must install the necessary drivers onto your
computer. The installation is quick and easy – please follow the instructions below:

1. Please insert the included installation disc into your computer's CD-ROM drive. DO NOT CONNECT THE
DJ|iO YET!

2. Double-click on Setup.exe.

3. Select your preferred language.

4. Click on Install the driver.

5. Read the User Agreement, select I accept the agreement, then click Install.

6. The installation procedure will begin. Please follow the on-screen instructions.

7. Once the installation has completed, you will see the screen on the left. Click Exit.

YOUR DJ|iO IS NOW READY TO USE!

MAC

Before you can begin using the DJ|iO with your computer, you must install the necessary drivers onto your
computer. The installation is quick and easy – please follow the instructions below:

1. Please insert the included installation disc into your computer's CD-ROM drive. DO NOT CONNECT THE
DJ|iO YET!

2. Open the CD to view its contents.

3. Please double-click Install DJ|iO to begin the installation procedure.

4. You will see the screen on the left appear. Click Continue.

5. Select your hard-drive as a destination for the driver installation and click Continue.

6. Click on Upgrade to begin the installation.

7. Enter your password and click OK.

8. You will see the warning displayed on the right.
Please select Continue Installation.

9. Click Restart to restart your computer and complete
the installation. Once your computer has restarted,
please plug in the DJ|iO.

YOUR DJ|iO IS NOW READY TO USE!

4

SOFTWARE AUDIO SETUP

CUE

If you are using the DJ|iO with Numark's Cue or
Cue Lite DJ software applications, please see the
example and instructions below for information on
routing your audio outputs to take full advantage of
cueing and monitoring.

In Cue, click on the Config button in the top right
corner of the screen to access Cue Lite's
configuration settings. You will see the window
shown on the right.

1. Select NONE from the Inputs pull-down
menu.

2. Select ASIO driver from the Sound card(s)
pull-down menu.

3. Select Numark USB Audio Device under
the ASIO driver pull-down menu.

4. Select Headphones from the Outputs pull­down menu.

5. Lastly, you can choose which outputs you
would like to use for your Master and
Headphones channels from the pull-down
menu on the bottom. Since the Headphone output on the DJ|iO is tied to the Output 2 stereo RCA pair, we
recommend leaving this option as it is (Master: Chan 1&2 / Headphones: Chan 3&4).

6. Click OK to exit the configuration settings.

Additional Information: You may also wish to send each virtual "deck" independently to each output pair on the
DJ|iO for use with an external mixer. To do so, please select External Mixer from the Outputs pull-down menu.
You will then be able to decide which deck is being sent to which output pair.

5

TRAKTOR

If you are using the DJ|iO with Native Instruments' Traktor or Traktor LE software applications, please see the
example and instructions below for information on routing your audio outputs to take full advantage of cueing and
monitoring.

1. In Traktor, click on Preferences.

2. Choose Audio Setup and click on
the Soundcard tab.

3. Next, under the Audio Device pull­down menu, select Numark USB
Audio Device.

4. Then click on the Output Routing
tab.

5. Lastly, you can choose which
outputs you would like to use for
your Master and Monitor channels
from the pull-down menu on the
bottom. Since the Headphone
output on the DJ|iO is tied to the
Output 2 stereo RCA pair, we
recommend using the Output 1 pair
as your Master channel and the
Output 2 pair as your Monitor channel.

Additional Information: You may also wish to send each virtual "deck" independently to each output pair on the
DJ|iO for use with an external mixer. To do so, please select External as the Mixer Mode in the Output Routing
tab. You will then be able to decide which deck is being sent to which output pair.

6

AUDIO LATENCY

Audio Latency describes the time that it takes for your
soundcard to respond to a command. In other words,
this is the time that it takes for your computer to
process data and output sound. The lower your
latency is, the faster your computer will respond to
commands and output sound.

For example, with high latency settings you may start
to notice a significant lag when you change EQ, level
and effect settings. In this case, you will want to
decrease your soundcard's latency in order to achieve
a quicker response.

To change latency settings for the DJ|iO, please open
the Numark USB Control Panel by clicking on Start f

All Programs f NUMARK f Numark USB Control
Panel.

You will see a drop-down menu on the lower portion of
the Numark USB Control Panel. Click on the drop­down arrow to view the available latency settings and
select the desired setting. Selecting '1024' samples
will result in a high audio latency and more lag, while
selecting '49' samples will give you the lowest audio
latency and quickest response.

Please note: Depending on your computer, some latency settings may not work correctly. If you are running on a
slower machine and try to use low audio latency settings ('49', '64', '128' samples), you may experience audio
drop-outs and glitches. If you experience drop-outs or glitches, you will need to increase the audio latency in the
Numark USB Control Panel by choosing one of the higher settings, such as '512' or '1024' samples.

7

CONTENIDO DE LA CAJA

DJ|iO Guía de inicio rápido
Cable USB Folleto de información sobre la seguridad y la garantía
CD

CARACTERÍSTICAS

1. PUERTO USB – Use el cable USB2.0 provisto
para conectar este puerto a un puerto USB2.0
disponible de su computadora. Cuando esté
enchufada a su computadora, la unidad extrae
energía por la conexión USB.

Para tener en cuenta: La interfaz DJ|iO
requiere una conexión USB2.0 para funcionar
plena y correctamente. Si usa una conexión
USB1.1, sólo funcionará la salida OUTPUT 1.
Para aprovechar ambas salidas, asegúrese de
conectar la unidad a un puerto compatible con
USB2.0 de su computadora.

2. DC IN (Entrada de CC) – Si su computadora no
suministra suficiente energía a través del bus
USB, es conveniente que alimente la unidad conectando un adaptador opcional de 6 V/1 A a esta entrada
y enchufando el adaptador a una fuente de alimentación.

3. OUTPUT 1 (Salida 1) – Esta conexión RCA estéreo entrega la mezcla maestra de su computadora. Use
un cable RCA estéreo para conectar esta salida a un sistema de altavoces alimentados o amplificador.

4. OUTPUT 2 (Salida 1) – Esta conexión RCA estéreo entrega la mezcla de cue de su computadora para
fines de monitoreo. Tenga en cuenta que la mezcla de cue sale también por la salida para auriculares
Headphone del panel frontal.

5. INDICADOR DE ENCENDIDO – Este LED se enciende para indicarle que la interfaz DJ|iO está
encendida.

6. ENTRADA MIC THROUGH – Es una entrada para micrófono de ¼". La señal de esta entrada se envía
directamente a la salida RCA estéreo Output 1 (mezcla maestra).

7. MIC VOL (Volumen de micrófono) – Esta perilla controla el nivel de micrófono que se envía a la salida
Output 1 (mezcla maestra).

8. HEADPHONES (Auriculares) – Esta salida estéreo de ¼" entrega la señal que se encamina a la salida
Output 2 (mezcla de cue). Para aprovechar plenamente las funciones de cue y monitoreo que produce
esta salida, asegúrese de encaminar la entrada Cue Mix (mezcla de cue) en su software a la salida Output
2 de la DJ|iO.

5

33

7

6

44

8

12

8

DIAGRAMA DE CONEXIÓN

Asegúrese de que su programa
de software de audio esté
configurado para recibir audio
por DJ|iO. Esto se puede hacer
habitualmente en "Preferences"
o "Device Setup" (Configuración
de dispositivos) de su software.
Para más información, consulte
el manual de su software.

MICRÓFONO AURICULARES COMPUTADORA

ALTAVOZ O SIST.

AMPLIFICADOR

(MAESTRO)

ALIMENTACIÓN

ALTAVOZ O SIST.

AMPLIFICADOR

(MONITOR)

9

INSTALACIÓN DE DRIVERS

PC

Antes de comenzar a usar la interfaz DJ|iO con su computadora, debe instalar en la misma los drivers
necesarios. La instalación es rápida y sencilla —siga las instrucciones que se incluyen a continuación:

1. Inserte el disco de instalación provisto en la lectora de CD-ROM de su computadora. ¡NO CONECTE LA
DJ|iO TODAVÍA!

2. Haga doble clic en Setup.exe.

3. Seleccione su idioma preferido.

4. Haga clic en Install the driver (Instalar driver).

5. Lea el Acuerdo de Usuario, seleccione I accept the agreement (Acepto el acuerdo) y luego haga clic en
Install (Instalar)

6. Comienza el procedimiento de instalación. Siga las instrucciones de la pantalla.

7. Una vez terminada la instalación, verá la pantalla de la izquierda. Haga clic en Exit (Salir)

¡AHORA, SU INTERFAZ DJ|iO ESTÁ LISTA PARA USAR!

MAC

Antes de comenzar a usar la interfaz DJ|iO con su computadora, debe instalar en la misma los drivers
necesarios. La instalación es rápida y sencilla —siga las instrucciones que se incluyen a continuación:

1. Inserte el disco de instalación provisto en la lectora de CD-ROM de su computadora. ¡NO CONECTE LA
DJ|iO TODAVÍA!

2. Abra el CD para ver su contenido.

3. Haga doble clic en Install DJ|iO (Instalar DJ|iO) para comenzar el procedimiento de instalación.

4. Verá aparecer la pantalla de la izquierda. Haga clic en Continue (Continuar).

5. Seleccione su disco duro como destino de instalación del driver y haga clic en Continue.

6. Haga clic en Upgrade (Actualizar) para comenzar la instalación.

7. Introduzca su contraseña y haga clic en OK (Aceptar).

8. Verá la advertencia que se muestra a la derecha.
Seleccione Continue Installation (Continuar la
instalación).

9. Haga clic en Restart (Reiniciar) para reiniciar su
computadora y completar la instalación. Una vez
reiniciada su computadora, enchufe la DFJ IO.

¡AHORA, SU INTERFAZ DJ|iO ESTÁ LISTA PARA
USAR!

10