NSC LM2936-5.0MDC, LM2936MX-5.0, LM2936MMX-5.0, LM2936MM-5.0, LM2936M-5.0 Datasheet
...
LM2936-5.0
Ultra-Low Quiescent Current 5V Regulator
General Description
The LM2936 ultra-low quiescent current regulator features
low dropout voltage and low current in the standby mode.
With less than 15 µA quiescent current at a 100 µA load, the
LM2936 is ideally suited for automotive and other battery
operated systems. The LM2936 retains all of the features
that are common to low dropout regulators including a low
dropout PNP pass device, short circuit protection, reverse
battery protection, and thermal shutdown. The LM2936 has
a 40V maximum operating voltage limit, a −40˚C to +125˚C
operating temperature range, and
±
3% output voltage tolerance over the entire output current, input voltage, and temperature range. The LM2936 is available in a TO-92 package, a SO-8 surface mount package, and a TO-252 surface
mount power package.
Features
n Ultra low quiescent current (IQ≤ 15 µA for IO= 100 µA)
n Fixed 5V, 50 mA output
n
±
2% Initial output tolerance
n
±
3% Output tolerance over line, load, and temperature
n Dropout voltage typically 200 mV
@
IO=50mA
n Reverse battery protection
n −50V reverse transient protection
n Internal short circuit current limit
n Internal thermal shutdown protection
n 40V operating voltage limit
n 60V operating voltage limit for LM2936HV
n Shutdown Pin available with LM2936BM package
Typical Application
00975901
* Required if regulator is located more than 2" from power supply filter capacitor.
*
*
Required for stability. Must be rated for 10 µF minimum over intended operating temperature range. Effective series resistance (ESR) is critical, see
curve. Locate capacitor as close as possible to the regulator output and ground pins. Capacitance may be increased without bound.
Connection Diagrams
TO-252 SOT-223
00975925
Top View
Order Number LM2936DT-5.0
See NS Package Number TD03B
00975926
Top View
Order Number LM2936MP-5.0
See NS Package Number MA04A
June 2002
LM2936-5.0 Ultra-Low Quiescent Current 5V Regulator
© 2002 National Semiconductor Corporation DS009759 www.national.com
Connection Diagrams (Continued)
8-Pin SO (M) 8-Pin SO (M)
00975906
Top View
Order Number LM2936M-5.0, LM2936HVMA-5.0
See NS Package Number M08A
00975927
Top View
Order Number LM2936BM-5.0, LM2936HVBMA-5.0
See NS Package Number M08A
TO-92 8-Pin Mini SOIC (MM)
00975902
Bottom View
Order Number LM2936Z-5.0
See NS Package Number Z03A
00975928
Top View
Order Number LM2936MM-5.0
See NS Package Number MUA08A
LM2936-5.0
www.national.com 2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Input Voltage (Survival) +60V, −50V
ESD Susceptibility (Note 2) 2000V
Power Dissipation (Note 3) Internally limited
Junction Temperature (T
Jmax
) 150˚C
Storage Temperature Range −65˚C to +150˚C
Lead Temperature (Soldering, 10
sec.) 260˚C
Operating Ratings
Operating Temperature Range −40˚C to +125˚C
Maximum Operating Input Voltage LM2936 +40V
Maximum Operating Input Voltage LM2936HV only +60V
Maximum Shutdown Pin Voltage LM2936BM only
0V to 40V
TO-92 (Z03A) θ
JA
195˚C/W
MSO-8 (MUA08A) θ
JA
200˚C/W
SO-8 (M08A) θ
JA
140˚C/W
SO-8 (M08A) θ
JC
45˚C/W
TO-252 (TD03B) θ
JA
136˚C/W
TO-252 (TD03B) θ
JC
6˚C/W
SOT-223 (MA04A) θ
JA
149˚C/W
SOT-223 (MA04A) θ
JC
36˚C/W
Electrical Characteristics
VIN= 14V, IO= 10 mA, TJ= 25˚C, unless otherwise specified. Boldface limits apply over entire operating temperature range
Parameter Conditions
Min
(Note 5)
Typical
(Note 4)
Max
(Note 5)
Units
LM2936HV Only
Output Voltage 5.5V ≤ V
IN
≤ 48V,
100 µA ≤ I
O
≤ 50 mA (Note 6)
4.85 5.00 5.15 V
Line Regulation 6V ≤ V
IN
≤ 60V, IO= 1mA 15 35 mV
All LM2936
Output Voltage
4.90 5.00 5.10
V
5.5V ≤ V
IN
≤ 26V,
100 µA ≤ I
O
≤ 50 mA (Note 6)
4.85 5.00 5.15
Quiescent Current I
O
= 100 µA, 8V ≤ VIN≤ 24V 9 15 µA
I
O
= 10 mA, 8V ≤ VIN≤ 24V 0.20 0.50 mA
I
O
= 50 mA, 8V ≤ VIN≤ 24V 1.5 2.5 mA
Line Regulation 9V ≤ V
IN
≤ 16V 5 10 mV
6V ≤ V
IN
≤ 40V, IO= 1 mA 10 30
Load Regulation 100 µA ≤ I
O
≤ 5mA 10 30 mV
5mA≤ I
O
≤ 50 mA 10 30
Dropout Voltage I
O
= 100 µA 0.05 0.10 V
I
O
= 50 mA 0.20 0.40 V
Short Circuit Current V
O
= 0V 65 120 250 mA
Output Impedance I
O
= 30 mAdc and 10 mArms, 450 mΩ
f
= 1000 Hz
Output Noise Voltage 10 Hz–100 kHz 500 µV
Long Term Stability 20 mV/1000
Hr
Ripple Rejection V
ripple
=1V
rms,fripple
= 120 Hz −40 −60 dB
Reverse Polarity R
L
= 500Ω, T = 1 ms −50 −80 V
Transient Input Voltage
Output Voltage with V
IN
= −15V, RL= 500Ω 0.00 −0.30 V
Reverse Polarity Input
Maximum Line Transient R
L
= 500Ω,VO≤ 5.5V, T = 40ms 60 V
LM2936-5.0
www.national.com3
Electrical Characteristics (Continued)
VIN= 14V, IO= 10 mA, TJ= 25˚C, unless otherwise specified. Boldface limits apply over entire operating temperature range
Parameter Conditions
Min
(Note 5)
Typical
(Note 4)
Max
(Note 5)
Units
Output Bypass
Capacitance (C
OUT
) ESR
C
OUT
= 10µF
0.1mA ≤ I
OUT
≤ 50mA
0.3 8 Ω
Shutdown Input − LM2936BM Only
Output Voltage, V
OUT
Output Off, VSD=2.4V, R
LOAD
= 500Ω 0 0.010 V
Shutdown High
Threshold Voltage, V
IH
Output Off, R
LOAD
= 500Ω 2.00 1.1 V
Shutdown Low
Threshold Voltage, V
IL
Output On, R
LOAD
= 500Ω 1.1 0.60 V
Shutdown High
Current, I
IH
Output Off, VSD= 2.4V, R
LOAD
= 500Ω 12 µA
Quiescent Current Output Off, VSD= 2.4V, R
LOAD
= 500Ω
Includes I
IH
Current
30 µA
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its specified operating ratings.
Note 2: Human body model, 100 pF discharge through a 1.5 kΩ resistor.
Note 3: The maximum power dissipation is a function of T
Jmax
, θJA, and TA. The maximum allowable power dissipation at any ambient temperature is
P
D
=(T
Jmax−TA
)/θJA. If this dissipation is exceeded, the die temperature will rise above 150˚C and the LM2936 will go into thermal shutdown.
Note 4: Typicals are at 25˚C (unless otherwise specified) and represent the most likely parametric norm.
Note 5: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 6: To ensure constant junction temperature, pulse testing is used.
Typical Performance Characteristics
Maximum Power
Dissipation (TO-92) Dropout Voltage
00975907 00975908
LM2936-5.0
www.national.com 4
Loading...