profile selection
&
esc adjustments
8-2007#55-3019P-1
throttle profile selection
The Goat Brushless/Brush Crawler speed control is equipped with 4
user-selectable Throttle Profiles, as shown below.
GOAT THROTTLE PROFILES
1 2 3 4
Std.Crawler Expo.Crawler Servo/Robotic Brush-Mode
w/Reverse
Throttle Curve linear expo linear linear
Programmable yes yes yes yes
Drag/Hill Brake
Dead Band%
Min.Drive%
In Brushless-Mode, One-Touch set-up reverts ESC back to Profile #1 & default settings.
selecting brushless profiles
With ESC on & connected to a charged battery
1.
IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
To avoid possible radio interference, remove the ESC’s input signal harness
from the receiver--Green LED will stay on to indicate no signal from receiver.
2. PRESS & HOLD THE ESC’S ONE-TOUCH SET BUTTON
Continue to hold SET button on ESC until all 4 LEDs turns on.
3.
RELEASE SET BUTTON AS SOON AS ALL 4 LEDs COMES ON
Once released, the 4 status LEDs will flash to indicate what Throttle Profile is
currently selected. The number of times the LEDs flash indicates the Brushless
Throttle Profile selection (1 of 3).
4.
QUICK PRESS
Each press will change to the next consecutive Throttle Profile. (After Profile
3 in Brushless-Mode, the sequence begins again at Profile 1)
Note: there is a time constraint during this selection process.
5.
ESC STORES SELECTION & BEGINS TO EXIT PROGRAMMING
If SET button is not pressed for 3 seconds, ESC stores selected Profile in
memory, exits to neutral & is ready to go. (LEDs turn off in a rolling motion
left to right, then Red LED turns on solid-signal present & Blue or Blue & Amber LEDs on if Drag or Min. Brakes above 0%)
Note: ESC reverts to factory default settings & Throttle Profile #1 whenever One-Touch set-up is
performed (reverts to Profile #4 Brush-Mode if no brushless motor sensor harness is connected).
Reverse%
BRUSHLESS MOTOR PROFILES
yes yes yes yes
100% 100% 100% 100%
3% 3% n/a yes
5% 5% 5% 5%
2% 2% 2% 2%
BRUSH MOTORS
NOTE: The Goat is factory set to Profile #1
all LEDs
:
(transmitter ON or OFF)
Note: You will continue holding past all the LED programming indicators in
the ESC’s software as shown in the flow chart on back side of this sheet.
(& release)
SET BUTTON TO CHANGE SELECTION
Green LED will be on if no transmitter
:
.
proper gear selection
Motor operating temperature is the
proper way to set the vehicle gearing
The motor should not exceed 170°F at end of run!
Change the gearing to avoid overheating.
If you do not change gearing after switching to brushless, you may be
over-geared and have slow acceleration & excessive temperatures!
With the extremely broad power band of the Novak Crawler brushless
motors, you can gear your vehicle for more top speed (without going
to a higher voltage battery pack), but remember gearing higher will
produce more speed control & motor heating. Always check the motor’s
operating temperature after making any gearing adjustments--motors
are designed to operate safely up to 160-170ºF.
proFile adjustments
The following parameters are adjustable in the ESC’s software:
DRAG BRAKE
10 settings from 10 to 90% in Brush-Mode)
while the transmitter is at neutral. Also known as ‘hill’ or ‘auto’ brakes.
Raising this setting makes the motor slow down more without
pushing the transmitter’s trigger into the brake/reverse direction.
This adjustment is not available in the Servo/Robotic Profile #3.
DEAD BAND (1 of 5 settings from 3 to 9%)--The space between Minimum
Brake and Minimum Drive, with neutral in the middle.
Raising this setting will increase the ‘free play’, or distance your
trigger must move before forward drive or braking will begin.
MINIMUM DRIVE (1 of 5 settings from 2 to 12%)--The amount of forward
drive applied with the first pulse of transmitter throttle information.
Raising this setting makes the motor start at a stronger/higher
DRIVE FREQUENCY
frequency at which the duty cycle information is being sent from the
speed control to the motor to control the speed.
Raising this setting makes the control of the motor feel more smooth.
Normally this value would be lowered for use with higher turn motors
to get more ‘punch’, and it would be raised for hotter, low-turn motors
or slippery track conditions for more control of the power delivery.
(1 of 10 settings from 1.5 to 13.5% in Brushless Profiles, & 1 of
--The amount of braking applied
level so it takes off more aggressively from neutral.
-Brush-Mode Only-(1 of 7 settings from 3.5 to 15kHz)
--The
expo throttle curve
Profile #2 in the Goat ESC’s software features an exponential throttle
curve in both the forward and reverse directions. This provides you
with extremely smooth throttle response for the precision movements
required in the most demanding technical rock crawling courses.
progressive ramP-uP braking
The Goat ESC’s braking use battery power to slow the motor, and can
supply amazing amounts of braking. In Brushless Profiles 1 & 2, the brakes
linearly ramp up to the value of Drag/Hill brakes that you program. This
provides smooth application of braking without risk of roll-overs.
mOtOr rOtAtiON SeleCtiOn
The Goat’s software lets you reverse the brushless motor’s rotation direction. This allows installation in vehicles with counter-rotating drive trains
(or opposed transmissions), without compromising
See reverse side of this sheet for programming instructions
performance.
Li-PO cUt-OFF circUitrY
When active (see programming on reverse side to turn ON/OFF), the built-in
Novak Smart-Stop Li-Po Cut-Off Circuitry lets you safely use 2S Lithium
Polymer battery packs by cutting off the speed control’s throttle output
when a critical safety voltage is reached.
The circuitry constantly monitors the pack voltage. When it gets close to
the critical safety voltage (6.25V) it begins interrupting, or ‘blipping’ the
throttle output as an early warning that the battery’s voltage is getting
low and the throttle output will soon be completely shut off.
When the critical voltage is reached, the throttle output to the motor
gets completely shut down to keep the voltage from dropping further
(Red & Green LEDs will alternately flash & you still have steering control).
Re-charge battery after Smart-Stop circuitry shuts off throttle
Even though the pack’s voltage will rise
high enough to run motor again, this is not good for Li-Po batteries.
Reaching critical safety voltage too many times can damage the cells.
DO NOT CONTINUE TO RUN VEHICLE AFTER THE SMART-STOP HAS SHUT
During power-up when the ESC is switched ON, the Amber & Red
LEDs will flash together 3 times to indicate Li-Po Cut-Off is ACTIVE.
With the Li-Po Cut-Off turned ON & using Ni-Cd or Ni-MH cells, the circuitry will shut off the
ESC’s throttle output very early into the run, due to the different characteristics of these batteries.
P5
(after a short resting period)
DOWN THE THROTTLE OUTPUT THE FIRST TIME.
to a level
advanced
-- CUSTOM programmiNG
to custom program profiles:
Your transmitter can be either ON or OFF:
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
Remove input signal harness from receiver to avoid radio interference.
2. CONNECT SPEED CONTROL TO A CHARGED BATTERY PACK
3. SLIDE ESC’s ON/OFF SWITCH TO ‘ON’ POSITION
4. MAKE SURE THE THROTTLE PROFILE TO ADJUST IS ACTIVE
If you are not sure what profile is selected, follow the procedures in ‘Throttle Profile
Selection’ to check or select the desired profile.
5. FOLLOW STEPS ON RIGHT SIDE OF THIS PAGE TO CUSTOMIZE ESC
You can adjust different parameters
speed control to perform & feel the way you like it.
Remember that you can not access the Brush-Mode
disconnecting the brushless motor’s sensor harness from the ESC.
Note: there is no time constraint during selection process of custom parameters.
(described on back side of this sheet)
(Profile #4)
to fine tune the
without
goat soFtware
Flow chart:
@NEUTRAL
RED LED on solid
press & hold
DRAG BRAKE
if Profile #3 active
if Brush-Mode active
DRIVE FREQUENCY
GREEN
press & hold
BLUE & AMBER
press & hold
DEAD BAND
BLUE & GREEN
press & hold
MIN. DRIVE
AMBER
press & hold
if Brushless-Mode
is active
LiPo CUT-OFF
AMBER & RED
press & hold
if Brush-Mode is
active
ACTIVE PROFILE
all LEDs (flashing)
if Brushless-Mode active
MOTOR ROTATION
AMBER & GREEN
press & hold
continue holding ESC’s SET button to skip steps here
to activate & adjust drag brake:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until the BLUE & AMBER status LEDs turn on
solid---Release SET button once LEDs are on solid.
b
. SELECT DRAG BRAKE PERCENTAGE
Blue & Amber status LEDs flash to indicate the Drag Brake setting. Quick press & release the
SET button to change the Drag Brake setting.
Drag Brake Values for Brushless Profiles:
Setting
Setting
(# of flashes)
(# of flashes)
Drag/Hill Brake
Drag Brake Values for Brush-Mode:
Drag/Hill Brake
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs will also be on)---ESC is at neutral & ready to go.
:
1 2 3 4 5 6 7 8
(%)
: 1.5 3 4.5 7.5 9.5 10.5 12 13.5
:
1 2 3 4 5 6 7 8 9 10
(%)
: 10 20 25 30 40 50 60 70 80 90
BLUE & AMBER LEDs ON ALWAYS
BLUE LED STAYS ON ALWAYS
blue & amber LEDs
to adjust dead band:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until the BLUE & GREEN status LEDs turn on
solid--Release SET button once LEDs are on solid.
b. SELECT DEAD BAND PERCENTAGE
Blue & Green status LEDs flash to indicate active Dead Band setting. Quick press & release SET
button to change setting.
Setting
Dead Band
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs may also be on)---ESC is at neutral & ready to go.
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until AMBER status LED turns on solid---Release
SET button once LED is on solid.
b. SELECT MINIMUM DRIVE PERCENTAGE
Amber status LED flashes to indicate active Minimum Drive setting. Quick press & release SET
button to change setting.
Minimum Drive
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs may also be on)--ESC is at neutral & ready to go.
to adjust drive frequency:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until GREEN status LED turns on solid---Release
SET button once LED is on solid.
b. SELECT DRIVE FREQUENCY
Green status LED flashes to indicate active Drive Frequency setting. Quick press & release SET
button to change setting.
Setting
Drive Frequency
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs may also be on)--ESC is at neutral & ready to go.
(# of flashes)
:
1 2 3 4 5
(%)
: 3 5 6 7 9
to adjust minimum drive:
Setting
(# of flashes)
(# of flashes)
(kHz)
:
1 2 3 4 5
(%)
: 2 3 5 8 12
:
1 2 3 4 5 6 7
: 3.5 4.5 5.5 6.5 7.5 10 15
blue & green LEDs
amber LED
(Profile 4 ONLY)
green LED
LEDs roll off
––––
if Brushless-Mode active
––––––
# of flashes equals
active profile (1-3)
if pressed within 3 sec.
of all LEDs flashing
active profile changed
if not pressed
within 3 sec. of
all LEDs flashing
––––––
if Brush-Mode active
––––––
all LEDs
flash 4 times
exit programming
@NEUTRAL
RED LED on solid
restoring factory defaults:
Every time you perform the One-Touch Set-Up, the factory default settings
are restored for each of the throttle profiles & ESC reverts to Profile #1.
to activate liPO cut-off circuitry:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until the AMBER & RED status LEDs turn on
solid---Release SET button once LEDs are on solid.
b. TURN LiPo CUT-OFF CIRCUITRY ON or OFF
Amber & Red status LEDs flash to indicate LiPo Cut-Off Circuitry setting. Quick press & release
SET button to change setting.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber
to reverse motor rotation:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until
solid
---Release SET button once LEDs are on solid.
b. SELECT MOTOR ROTATION DIRECTION
Amber & Green status LEDs flash to indicate motor rotation direction. Quick press & release
SET button to change setting.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming.Red
LED turns on solid (Blue & Amber LEDs may also be on)--ESC is at neutral & ready to go.
ww w .t e am n ov a k. c om
P6
LEDs may also be on)
1 flash = OFF 2 flashes = ON
--ESC is at neutral & ready to go.
1 flash
amber & red LEDs
AMBER & GREEN
amber & green LEDs
= Normal 2 flashes
status LEDs turn on
=
Reverse
Loading...