This conversion kit is intended to increase drawer capacity for Julian.
Note: This conversion is only for use wit h t he chassis extension Big Foot 8601798!
Dräger Medizintechnik GmbH, D-23542 Lübeck
2 Included in the Kit
The conversion kit "RS Extra Drawers" 8601966 contains the following parts:
- 1 chest of drawers with guide rail
- 1 adapter for mounting t o Julian
Loose parts:
- 2 x 2M18572cap
- 1 x 8601959sheet
- 1 x 8601958sheet
- 1 x M29110sheet
- 2 x 1263196screw
- 1 x 1295594screw
- 1 x 8601981conversion instructions for Julian “extra drawers”
3 General
This conversion should be carried out by a service technician.
8601981 - 00 , de
RELEASED
page 1 of 6
Page 2
Dräger
Medizintechnik
Drä
Disassemble all mounted hinged arms and auxiliary devices located on the right side of the
device (advantageous).
I
Schutz nach D IN 34 beansprucht.
Use of the docu ment / contents is forbidden
without express authority. All rights reserved.
Dräger Medizintechnik GmbH, D-23542 Lübeck
8601981 - 00 , de
RELEASED
page 2 of 6
Page 3
Dräger
Medizintechnik
Drä
4 Tools
4.1 Tools:
Basic tool kit, including:
- Allan key 5.0 mm
- power screwdriver or drill
- drill bit ∅ 5.0 mm and thread cutt er M6
5 Instructions
5.1 General:
During the conversion, be sure to avoid damaging t he side panel and t he chassis of the device.
The conversion kit “extra drawers” is pre-assembled and only requires final mounting and
adjustment.
5.2 Installation:
I
Schutz nach D IN 34 beansprucht.
Use of the docu ment / contents is forbidden
without express authority. All rights reserved.
1. Remove the standard rail cover from the right side of the device (as seen when facing the
front of the device).
2. Remove the hand railing (bent rail profile), but not the handle, from the right side of the
Dräger Medizintechnik GmbH, D-23542 Lübeck
device.
3. Cover the location hole of the hand railing with the cap 2M18572.
4. If this is not present: drill and cut a thread M6 (see Illustrat ion 1).
5. Mount the adapter to Julian using the two screws M6x12 1263196 and sheet M29110 (see
Illustration 2).
6. Connect the chest of drawers and its guide rail to the adapter f r om below and carefully set it
on the chassis extension; screw the stud screws and the screws M6X40 1295594 into the
adapter.
7. Refit and remount the rail cover.
6 Final Testing
- Remount dismounted options.
- Perform function t est for device.
8601981 - 00 , de
RELEASED
page 3 of 6
Page 4
Dräger
Medizintechnik
Illustr at ion 1: fastening hole in the chassis extension
Drä
I
Schutz nach D IN 34 beansprucht.
Use of the docu ment / contents is forbidden
without express authority. All rights reserved.
Dräger Medizintechnik GmbH, D-23542 Lübeck
8601981 - 00 , de
RELEASED
page 4 of 6
Page 5
Dräger
Medizintechnik
Illustr at ion 2: r ight side of device with chest of drawers
Drä
I
Schutz nach D IN 34 beansprucht.
Use of the docu ment / contents is forbidden
without express authority. All rights reserved.
Dräger Medizintechnik GmbH, D-23542 Lübeck
8601981 - 00 , de
RELEASED
page 5 of 6
Page 6
Dräger
Medizintechnik
Drä
I
Schutz nach D IN 34 beansprucht.
Use of the docu ment / contents is forbidden
without express authority. All rights reserved.
Dräger Medizintechnik GmbH, D-23542 Lübeck
8601981 - 00 , de
RELEASED
page 6 of 6
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.