NordicTrack NTCCEL169070 Owner's Manual
odel No. NTCCEL16907.0
www.nordictrack.com
Visit our website at
w
M
Serial No.
Write the serial number in the
space above for reference.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
USERʼS MANUAL
CALL TOLL-FREE:
1-888-936-4266
Mon.–Fri., 8:00 until 17:00 EST
(excluding holidays)
OR E-MAIL US:
customerservice@iconcanada.ca
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
A
HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing
or illegible, call the telephone number
on the front cover of this manual and
request a free replacement decal.
Apply the decal in the location shown.
Note: The decal(s) may not be shown at
actual size.
NordicTrack is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
hrough the use of this product.
t
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. Your elliptical exerciser is intended for
home use only. Do not use your elliptical
exerciser in a commercial, rental, or institutional setting.
4. Keep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around your elliptical exerciser to mount,
dismount, and use it.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from your elliptical exerciser at all times.
7. Your elliptical exerciser should not be used
by persons weighing more than 350 lbs.
(159 kg).
8. Wear appropriate exercise clothes when
exercising; do not wear loose clothes that
could become caught on your elliptical exerciser. Always wear athletic shoes for foot
protection.
9. Hold the handgrip pulse sensor or the handlebars when mounting, dismounting, or
using your elliptical exerciser.
10. Keep your back straight while using your
elliptical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the userʼs movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. If you feel pain or dizziness while exercising, stop immediately and cool down.
14. Use your elliptical exerciser only as
described in this manual.
3
BEFORE YOU BEGIN
Congratulations for purchasing the revolutionary
ordicTrack COMMERCIAL™ 1300 elliptical exer-
N
ciser. The NordicTrack COMMERCIAL 1300 elliptical
exerciser provides a wide array of features designed
to make your workouts at home more effective and
enjoyable.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
Handlebar
Pulse Sensor
Water Bottle Holder*
tions after reading this manual, please see the front
over of this manual. To help us assist you, note the
c
product model number and serial number before contacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Fan
Console
Pedal Disc
Handle
Leveling Foot
Ramp
Wheel
Pedal
*No water bottle is included
4
ASSEMBLY
#8 x 3/4"
Screw (78)–4
5/16" x 1" Patch
Screw (81)–11
#10 x 1/2"
Screw (79)–10
5/16" x 1.5" Button
Bolt (73)–4
5/16" Washer
(104)–6
#10 Fender
Washer (80)–10
5/8" Wave
Washer (102)–6
5/16" Split
Washer (105)–5
5/16" Nylon
Locknut (106)–4
M10 x 20mm Patch
Screw (108)–6
Pivot Spacer
(71)–4
5/16" x 2 1/2" Button
Screw (88)–8
M10 Split
Washer (110)–6
M6 Split
Washer
(111)–10
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included tools and your own Phillips screwdriver , adjustable
wrench , and rubber mallet .
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The
number following the parentheses is the quantity needed for assembly. Note: Some small parts may have
been preassembled. If a part is not in the hardware kit, check to see if it has been preassembled.
5
.
1
To make assembly easier, read the
information on page 5 before you begin
ssembling the elliptical exerciser.
a
With the help of another person, place the two
packing inserts under the front of the Frame (1)
so that the Frame is lifted off the floor. Have the
other person hold the elliptical exerciser to
prevent it from moving until this step is
completed.
1
1
Attach the Front Stabilizer (2) to the Frame (1)
with four 5/16" x 2 1/2" Button Screws (88).
Then, remove the packing inserts and lower the
Front Stabilizer.
2. With the help of a second person, place two
packing inserts from the packing material under
the rear of the Frame (1) so that the Frame is
lifted off the floor. Have the other person hold
the elliptical exerciser to prevent it from
moving until this step is completed.
Attach the Rear Stabilizer (3) to the Frame (1)
with four 5/16" x 2 1/2" Button Screws (88).
Then, remove the packing inserts and lower the
Rear Stabilizer.
2
88
88
2
1
3
88
88
6
3. Tip: Be careful not to pinch the Wire
Harnesses (97, 54) during this step. Start all
screws before tightening any of them.
While a second person holds the Upright (6)
ear the Frame (1), connect the Upper Wire
n
Harness (97) to the Lower Wire Harness (54).
3
Attach the Upright (6) to the Frame (1) with five
5/16" x 1" Patch Screws (81) and five 5/16"
Split Washers (105).
4. Apply a generous amount of the included
grease to the Pivot Axle (33) and to two 5/8"
Wave Washers (102).
Tip: Avoid pinching or damaging the Upper
Wire Harness (97). Insert the Pivot Axle (33)
through the Upright (6). Then, slide a 5/8" Wave
Washer (102) onto each end of the Pivot Axle.
Avoid pinching the
Wire Harnesses (97,
54) during this step
6
97
81
105
81
4
104
81
94
102
97
54
1
105
81
Grease
Slide an Upper Body Arm (12) onto the left side
of the Pivot Axle (33). Attach the Upper Body
Arm with a 5/16" x 1" Patch Screw (81), a Large
Axle Cover (94), and a 5/16" Washer (104).
Attach the other Upper Body Arm (12) in the
same way.
104
12
6
33
102
94
81
12
7
5. Identify the Right Pedal Plate (107), which is
marked with an “R” sticker. Attach the Right
edal Plate to the Right Pedal Arm (8) with
P
three M10 x 20mm Patch Screws (108) and
three M10 Split Washers (110).
dentify the Right Pedal Assembly (62), which is
I
located in a package marked with a “Right”
sticker. Attach the Right Pedal Assembly to the
Right Pedal Plate (107) with five #10 x 1/2"
Screws (79), five M6 Split Washers (111), and
five #10 Fender Washers (80). Tip: To avoid
damaging the Pedal, do not overtighten the
Screws.
Repeat this step for the Left Pedal Plate (not
shown) and the Left Pedal Assembly (56).
5
62
08
1
110
07
1
56
80
8
111
79
79
6. Identify the Right Link Arm (10), which is
marked with a sticker. Lightly grease the two
axles on the Right Link Arm and the two 5/8"
Wave Washers (102). Then, slide a Pivot
Spacer (71) and a Wave Washer onto each
axle.
At the same time, work the Right Link Arm (10)
into the right Upper Body Arm (12) and into the
Right Pedal Arm (8).
Attach the Right Link Arm (10) to the right
Upper Body Arm (12) with a 5/16" x 1" Patch
Screw (81), a Large Axle Cover (94), and a
5/16" Washer (104).
Then, attach the Right Link Arm (10) to the
Right Pedal Arm (8) with a 5/16" x 1" Patch
Screw (81), a Small Axle Cover (67), and a
5/16" Washer (104).
Tip: If it is difficult to work the Right Link
Arm (10) into the right Upper Body Arm (12)
and the Right Pedal Arm (8), try working the
Right Link Arm in halfway and then tightening the 5/16" x 1" Patch Screws (81) to pull it
in the rest of the way.
6
12
81
67
104
104
81
94
71
102
8
Grease
10
Grease
102
71
Repeat this step for the other side of the
elliptical exerciser.
8
. While a second person holds the Console (60)
7
near the Upright (6), connect the console wire to
the Upper Wire Harness (97). Then, connect the
console pulse wire to the Hand Pulse Wire (65).
Insert the excess wire downward into the
Upright.
Tip: Avoid pinching the wires during this
step. Attach the Console (60) to the Upright (6)
with four #8 x 3/4" Screws (78).
7
Console Wire
60
97
Avoid pinching the
wires during this step
Pulse Wire
5
6
6
78
8. Identify the Right Handlebar (31), which is
marked with a “Right” sticker and orient it as
shown. Attach the Right Handlebar to the right
Upper Body Arm (12) with two 5/16" x 1.5"
Button Bolts (73) and two 5/16" Locknuts (106).
Make sure that the Locknuts are in the
hexagonal holes.
Repeat this step to attach the Left Handlebar
(7) to the left Upper Body Arm (12).
9. Plug the Power Cord (55) into the power socket
at the rear of the elliptical exerciser (see HOW
TO PLUG IN THE POWER CORD on page 10).
IMPORTANT: If the elliptical exerciser has
been exposed to cold temperatures, allow it
to warm to room temperature before plugging in the power cord. If you do not do this,
the console displays or other electronic
components may become damaged.
8
7
73
12
9
31
106
Hexagonal
Holes
12
The ramp will calibrate automatically when
the elliptical exerciser is plugged in for the
first time.
10. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
55
9
Loading...