Page 1
Model No. NTEVEL89909.2
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal
(under frame)
QUESTIONS?
If you have questions, or if there are
missing parts, please contact us:
UK
Call: 08457 089 009
From Ireland: 053 92 36102
Website: www.iconsupport.eu
E-mail: csuk@iconeurope.com
USERʼS MANUAL
Write:
ICON Health & Fitness, Ltd.
c/o HI Group PLC
Express Way
Whitwood, West Yorkshire
WF10 5QJ
UK
AUSTRALIA
Call: 1-800-237-173
E-mail:
australiacc@iconfitness.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
www.iconeurope.com
Page 2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
I
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
RECYCLING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, see
the front cover of this manual and request a
free replacement decal. Apply the decal in the
location shown. Note: The decal(s) may not be
shown at actual size.
NordicTrack is a registered trademark of ICON IP, Inc.
2
Page 3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON
assumes no responsibility for personal injury or property damage sustained by or through the use of
his product.
t
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or
persons with pre-existing health problems.
2. Use the elliptical only as described in this
manual.
3. It is the responsibility of the owner to ensure
that all users of the elliptical are adequately
informed of all precautions.
4. The elliptical is intended for home use only.
Do not use the elliptical in a commercial,
rental, or institutional setting.
5. Keep the elliptical indoors, away from
moisture and dust. Do not put the elliptical in
a garage or covered patio, or near water.
6. Place the elliptical on a level surface, with at
least 3 ft. (0.9 m) of clearance in the front
and rear of the elliptical and 2 ft. (0.6 m) on
each side. To protect the floor or carpet from
damage, place a mat under the elliptical.
9. The elliptical should not be used by persons
weighing more than 325 lbs. (147 kg).
10. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical. Always wear athletic
shoes for foot protection while exercising.
11. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical.
12. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in
determining heart rate trends in general.
13. The elliptical does not have a freewheel; the
pedals will continue to move until the
flywheel stops. Reduce your pedaling speed
in a controlled way.
14. Keep your back straight while using the
elliptical; do not arch your back.
7. Inspect and properly tighten all parts
regularly. Replace any worn parts
immediately.
8. Keep children under age 12 and pets away
from the elliptical at all times.
15. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
3
Page 4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary NordicTrack
10 REAR DRIVE elliptical. The E10 REAR DRIVE
E
elliptical provides an impressive selection of features
designed to make your workouts at home more effective and enjoyable.
®
reading this manual, please see the front cover of this
anual. To help us assist you, note the product model
m
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
For your benefit, read this manual carefully before
you use the elliptical. If you have questions after
H: 5 ft. 5 in. (165 cm)
W: 2 ft. 3 in. (69 cm)
L: 6 ft. 9 in. (206 cm)
Wt.: 185 lbs. (84 kg)
Upper Body Arm
Fan
Accessory Tray
Pedal
Storage Magnet
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Pulse Sensor
Ramp
Access
Cover
Power
Switch
Handle
Leveling Foot
Wheel
Leveling Foot
Latch Button
Pedal Arm Latch
Power Cord
4
Page 5
ASSEMBLY
M10 x 95mm Patch
Screw (100)–4
M8 Split Washer
(103)–14
M8 Washer
(95)–6
M8 x 16mm Patch
Screw (102)–16
Wave Washer
(118)–2
M6 Washer
(112)–8
M8 x 25mm Patch
Screw (121)–2
M6 x 50mm Patch
Screw (62)–4
M8 x 35mm Patch
Screw (149)–2
M4 x 19mm
Screw (156)–8
M6 x 12mm Patch
Screw (111)–4
Assembly requires two persons. Place all parts of the elliptical in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires a Phillips screwdriver and a rubber
mallet .
See the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following
the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if
it has been preassembled. To avoid damaging parts, do not use power tools for assembly.
5
Page 6
1.
To make assembly easier, read the
nformation on page 5 before you begin.
i
Identify and orient the Rear Stabilizer (4) as
hown.
s
See HOW TO FOLD AND UNFOLD THE
ELLIPTICAL on page 15, and unfold the elliptical.
While a second person lifts the Folding Frame
(2), attach the Rear Stabilizer (4) to the Folding
Frame with two M10 x 95mm Patch Screws
(100).
1
4
2
100
2. Orient the Front Stabilizer (3) so that the welded
tubes are facing away from the Main Frame (1).
While a second person lifts the front of the Main
Frame (1), attach the Front Stabilizer (3) to the
Main Frame with two M10 x 95mm Patch
Screws (100).
2
3
1
Welded
Tubes
100
6
Page 7
3. Identify and orient the Upright (5) and the Top
Cover (27) as shown.
3
Slide the Top Cover (27) upward onto the
Upright (5).
Then, have a second person hold the Upright
(5) and the Top Cover (27) near the Main Frame
(1).
Locate the wire tie in the Upright (5). Tie the
lower end of the wire tie to the Wire Harness
(60). Next, pull the upper end of the wire tie
until the Wire Harness is routed completely
through the Upright.
Tip: To prevent the Wire Harness (60) from
falling into the Upright (5), secure the Wire
Harness with the wire tie.
Tip: Avoid pinching the Wire Harness (60).
Insert the Upright (5) into the Main Frame (1).
Attach the Upright (5) with four M8 x 16mm
Patch Screws (102) and four M8 Split Washers
(103); do not tighten the Patch Screws yet.
ire Tie
W
Wire Tie
102
Avoid pinching the
Wire Harness (60)
5
27
102
103
60
1
102
103
103
102
7
Page 8
. Apply a generous amount of the included
4
grease to the Upright Axle (48) and to two Wave
Washers (118).
ip: Avoid damaging the Wire Harness (60).
T
Insert the Upright Axle (48) through the Upright
5) and center it. Slide a Wave Washer (118)
(
onto each side of the Upright Axle.
Next, identify the Right and Left Upper Body
Legs (6, 7), which are marked with “Right” and
“Left” stickers, and orient them as shown.
Slide the Right and Left Upper Body Legs (6, 7)
onto the right and left sides of the Upright Axle
(48).
Tighten an M8 x 16mm Patch Screw (102) and
an M8 Washer (95) into each end of the Upright
Axle (48) at the same time.
4
102
95
60
Avoid damaging the
118
7
rease
G
Wire Harness (60)
5
48
Grease
118
95
102
6
5. Identify the Right Pedal (14), the Right Gel Pad
(158), and the Right Pedal Arm (12), which are
marked with “Right” stickers, and orient them as
shown.
Set the Right Gel Pad (158) on the Right Pedal
Arm (12). Then, set the Right Pedal (14) on the
Right Gel Pad.
Attach the Right Pedal (14) to the Right Pedal
Arm (12) with two M6 x 12mm Patch Screws
(111) and two M6 Washers (112); do not
tighten the Patch Screws yet.
Next, tighten two M6 x 50mm Patch Screws
(62) and two M6 Washers (112) into the Right
Pedal Arm (12) and the Right Pedal (14). Then,
tighten the two M6 x 12mm Patch Screws
(111).
Attach the Left Pedal (not shown) to the Left
Pedal Arm (not shown) assembly in the
same way.
5
14
158
112
12
62
112
111
62
8
Page 9
6. Apply grease to the axle on the right Crank Arm
(39).
Orient a Pedal Arm Sleeve (46) so that the flat
side is facing the elliptical. Slide the Pedal Arm
Sleeve onto the axle on the right Crank Arm
(39).
Attach the Pedal Arm Sleeve (46) with an M8 x
25mm Patch Screw (121), a Large Axle Cover
(113), and an M8 Washer (95). Tip: Avoid
damaging the Large Axle Cover when tightening the Patch Screw.
Repeat this step on the other side of the
elliptical.
6
Grease
39
Flat
Side
46
95
113
121
7. See drawing 7a. Locate the Pedal Arm Roller
(32) on the Right Pedal Arm (12).
Set the Pedal Arm Roller (32) on the right side
of the Ramp (130).
See drawing 7b. Pull upward on the Latch (50)
on the Right Pedal Arm (12).
Press the Right Pedal Arm (12) onto the right
Pedal Arm Sleeve (46). Make sure that the
Right Pedal Arm latches into place.
Repeat this step on the other side of the
elliptical.
7a
32
12
130
7b
12
50
46
9
Page 10
8. Orient the Ramp Cover (131) around the
Upright (5) as shown.
Press the tabs on the Ramp Cover (131) into
the Ramp (130).
8
5
131
130
9. Apply grease to a Link Arm Axle (114).
Insert the Link Arm Axle (114) into the Right
Upper Body Leg (6) and the Right Link Arm (43)
from the side shown.
Insert a hex key into the M8 x 35mm Patch
Screw (149) in the Link Arm Axle (114).
Using a second hex key, tighten another M8 x
35mm Patch Screw (149), a Small Axle Cover
(56), and an M8 Washer (95) into the other end
of the Link Arm Axle (114). Tip: Avoid damag-
ing the Small Axle Cover when tightening
the Patch Screw.
Repeat this step on the other side of the
elliptical.
9
149
Grease
6
114
95
56
149
43
10
Page 11
0. Identify the Right Upper Body Arm (8), which is
1
marked with a “Right” sticker, and orient it as
hown.
s
Have a second person hold the Right Upper
Body Arm (8) near the Right Upper Body Leg
6).
(
Attach the Right Upper Body Arm (8) to the
Right Upper Body Leg (6) with three M8 x
16mm Patch Screws (102) and three M8 Split
Washers (103).
Attach the Left Upper Body Arm (9) to the
Left Upper Body Leg (7) in the same way.
See step 3 on page 7. Tighten the M8 x 16mm
Patch Screws (102).
Slide the Top Cover (27) downward and press it
into the Right and Left Frame Covers (21, 22).
10
9
8
7
102
103
27
6
102
11. Identify the Right Handlebar (10), which is
marked with a “Right” sticker, and orient it as
shown.
Have a second person hold the Right
Handlebar (10) near the right side of the Upright
(5).
Insert the Pulse Wire (105) from the Right
Handlebar (10) into the right side of the Upright
(5) and pull it upward out of the top of the
Upright.
Tip: To prevent the Pulse Wire (105) from
falling into the Upright (5), secure the Pulse
Wire with a rubber band or tape.
Tip: Avoid pinching the Pulse Wire (105).
Attach the Right Handlebar (10) to the Upright
(5) with two M8 x 16mm Patch Screws (102)
and two M8 Split Washers (103).
11
21, 22
105
11
Avoid pinching the
Pulse Wires (105)
105
10
103
102
5
Attach the Left Handlebar (11) in the same
way.
11
Page 12
12. Untie and discard the wire tie on the Wire
Harness (60).
While a second person holds the Console (33)
near the Upright (5), connect the wires on the
onsole to the Wire Harness (60) and to the
C
Pulse Wires (105).
Insert the excess wire downward into the
Upright (5) or upward into the Console (33).
12
Avoid pinching
the wires
33
Upper
Holes
105
Tip: Avoid pinching the wires. Finger tighten
two M4 x 19mm Screws (156) through the
Upright (5) into the upper end of the Console
(33). Make sure to start the Screws into the
indicated upper holes in the Console.
Do not tighten the M4 x 19mm Screws (156)
yet.
13. Orient the Rear Upright Cover (25) as shown.
Attach the Rear Upright Cover (25) to the
Upright (5) with four M4 x 19mm Screws (156).
Tip: It may be necessary to bend the upper
end of the Rear Upright Cover gently into
place around the Upright.
13
60
5
156
156
5
25
12
Page 13
14. Attach the lower end of the Console (33) to the
Upright (5) with two M4 x 19mm Screws (156).
See step 12 on page 12. Tighten the M4 x
19mm Screws (156) in the upper end of the
Console (33).
4
1
33
156
5
156
15. Orient the Front Upright Cover (24) as shown.
Attach the Front Upright Cover (24) around the
Upright (5) by pressing the tabs on the Front
Upright Cover into the Rear Upright Cover (25).
See HOW TO PLUG IN THE POWER CORD
on page 14 and plug the power cord into the
receptacle on the frame of the elliptical. Then,
attach the adapter to the power cord, if necessary.
16. Make sure that all parts of the elliptical are properly tightened. Note: Some hardware may be left over
after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical.
15
24
25
5
13
Page 14
HOW TO USE THE ELLIPTICAL
HOW TO PLUG IN THE POWER CORD
his product must be earthed. If it should malfunc-
T
tion or break down, earthing provides a path of least
esistance for electric current to reduce the risk of
r
electric shock. This product is equipped with a power
cord having an equipment-earthing conductor and an
earthing plug. IMPORTANT: If the power cord is
damaged, it must be replaced with a manufacturerrecommended power cord.
DANGER: Improper connection
of the equipment-earthing conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly earthed. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1. Plug the indicated end of the appropriate power
cord into the receptacle on the elliptical.
Receptacle
on Elliptical
Power Cord
2. Plug the power
cord into an
appropriate outlet that is
properly
installed and
earthed in
accordance
with all local
codes and ordinances.
Outlet
14
Page 15
HOW TO FOLD AND UNFOLD THE ELLIPTICAL
When the elliptical is not in use, the frame can be
olded out of the way. First, lift the latch under each
f
pedal arm, and lift the pedal arms off the sleeves on
he crank arms.
t
To use the elliptical, first hold the handle, press the
latch button, and lower the frame.
ext, pull the magnets on the pedal arms off the han-
N
dlebars. Then, lift the latches under the pedal arms,
nd set the pedal arms on the sleeves on the crank
a
arms. Release the latches, and make sure that the
pedal arms are securely connected to the crank arms.
HOW TO MOVE THE ELLIPTICAL
Sleeve
Pedal Arm
Latch
Next, raise the pedal arms until the magnets on the
pedal arms touch the handlebars; the magnets will
hold the pedal arms in place. Then, hold the handle
and lift the frame until it locks in a vertical position.
Magnet
Pedal
Arm
Handle
To move the elliptical, first fold it as described at the
left. Next, stand in front of the elliptical, hold the
upright, and place one foot against one of the wheels.
Pull the upright until the elliptical rolls on the wheels.
With the help of a second person, carefully move the
elliptical to the desired location, and then lower it to
the floor.
Pull on the
upright
Place your
foot here
Latch
Button
15
Page 16
HOW TO EXERCISE ON THE ELLIPTICAL
HOW TO LEVEL THE ELLIPTICAL
To mount the elliptical, hold the upper body arms and
tep onto the pedal that is in the lowest position. Next,
s
step onto the other pedal. Push the pedals until they
egin to move with a continuous motion.
b
Upper Body Arms
Handlebars
Pedals
Crank
Arm
If the elliptical
ocks slightly on
r
your floor during
se, turn one or
u
both of the leveling feet beneath
the rear stabilizer until the
rocking motion is
eliminated.
If the frame of
the elliptical
flexes during
use, turn the
center leveling
foot until the
flexing motion is
eliminated.
Leveling
Feet
Leveling
Foot
Note: The crank arms can turn in either direction.
It is recommended that you turn the crank arms in
the direction shown by the arrow; however, for
variety you can turn the crank arms in the opposite direction.
To dismount the elliptical, wait until the pedals come to
a complete stop. Note: The elliptical does not have
a free wheel; the pedals will continue to move until
the flywheel stops. When the pedals are stationary,
step off the higher pedal first. Then, step off the lower
pedal.
16
Page 17
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
When you use the manual mode of the console, you
can change the resistance of the pedals and the
incline of the ramp with the touch of a button. While
you exercise, the console will display continuous exercise feedback. You can also measure your heart rate
using the handgrip pulse sensor or the optional chest
pulse sensor.
In addition, the console offers twenty preset workouts—six weight loss workouts and fourteen
performance workouts. Each workout automatically
changes the resistance of the pedals and prompts you
to vary your pedaling pace as it guides you through an
effective workout.
The console also features the iFit interactive workout
system, which enables the console to accept iFit cards
containing workouts designed to help you achieve
specific fitness goals. For example, lose unwanted
pounds with the 8-week Weight Loss workout. iFit
workouts control the resistance of the pedals while the
voice of a personal trainer coaches you through your
workouts. iFit cards are available separately. To pur-
chase iFit cards, go to www.iFit.com or see the
front cover of this manual. iFit cards are also
available at select stores.
You can even connect your MP3 player or CD player
to the console sound system and listen to your favorite
music or audio books while you exercise.
To turn on the power, see page 18. To use the manual mode, see page 18. To use a preset workout,
see page 20. To use an iFit workout, see page 21.
To use the sound system, see page 21. To change
console settings, see page 21.
Note: If there is a sheet of plastic on the display,
remove the plastic.
17
Page 18
HOW TO TURN ON THE POWER
IMPORTANT: If the elliptical has been exposed to
old temperatures, allow it to warm to room tem-
c
perature before turning on the power. If you do not
o this, you may damage the console displays or
d
other electrical components.
Plug in the power cord (see
HOW TO PLUG IN THE
POWER CORD on page
14). Next, locate the power
switch on the frame near
the power cord. Make sure
that the power switch is in
the reset position.
The display will then light and the console will be
ready for use.
Note: When you turn on the power for the first
time, the ramp will calibrate automatically. The
ramp will move upward and downward as it calibrates.
When the ramp stops moving, the ramp is calibrated.
IMPORTANT: If the ramp does not calibrate automatically, see HOW TO CALIBRATE THE RAMP on
page 23 and manually calibrate the ramp.
Reset
Position
3. Change the resistance of the pedals and the
incline of the ramp as desired.
s you pedal,
A
change the resis-
ance of the pedals
t
by pressing the
Resistance
increase and
decrease buttons.
Note: After you press the buttons, it will take a
moment for the pedals to reach the selected resistance level.
To vary the motion
of the pedals, you
can change the
incline of the ramp.
To change the
incline, press one
of the numbered Quick Touch Ramp buttons.
Note: After you press the button, it will take a
moment for the ramp to reach the selected incline
level.
4. Follow your progress with the display.
HOW TO USE THE MANUAL MODE
1. Begin pedaling or press any button on the
console to turn on the console.
See HOW TO TURN ON THE POWER above.
2. Select the manual mode.
Each time you turn
on the console, the
manual mode will
be selected. If you
have selected a
workout, reselect
the manual mode
by pressing any of
the Workouts buttons repeatedly
until zeros appear in the display.
The lower left
display—This dis-
play can show the
elapsed time and
the distance (total
number of revolutions) that you have pedaled. Note: When a
workout is selected, the display will show the time
remaining in the workout instead of the elapsed
time.
The lower right
display—This dis-
play can show your
pedaling speed (in
revolutions per
minute) and the
approximate number of calories that you have
burned.
This display also shows your heart rate when you
use the handgrip pulse sensor or the optional chest
pulse sensor (see step 5 on page 19).
18
Page 19
The upper
display—This dis-
play can show the
lapsed time, the
e
distance that you
ave pedaled, your
h
pedaling speed, and the approximate number of
calories you have burned.
Press the Display button repeatedly until the upper
display shows the information that you are most
interested in viewing. Note: While information is
shown in the upper display, the same information
will not be shown in the lower left or lower right display.
The lower
display—This dis-
play will show a
track representing
640 revolutions
(1/4 mile or 400
meters). As you exercise, indicators will appear in
succession around the track until the entire track
appears. The track will then disappear and the indicators will again begin to appear in succession.
To change the volume level of the console, press
the Vol increase and decrease buttons.
5. Measure your heart rate if desired.
When your pulse is
detected, a flashing
heart symbol will
ppear in the dis-
a
play, and then your
eart rate will
h
appear. For the most accurate heart rate reading,
hold the contacts for at least 15 seconds. Note: If
you continue to hold the handgrip pulse sensor,
the display will show your heart rate for up to 30
seconds.
If the display does not show your heart rate, make
sure that your hands are positioned as described.
Be careful not to move your hands excessively or
to squeeze the metal contacts tightly. For optimal
performance, clean the metal contacts using a soft
cloth; never use alcohol, abrasives, or chemi-
cals to clean the contacts.
6. Turn on the fan if desired.
The fan has high and low speed settings. Press
the Coolaire Fan button repeatedly to select a fan
speed or to turn off the fan.
Note: If the pedals do not move for about thirty
seconds, the fan will turn off automatically.
7. When you are finished exercising, unplug the
power cord.
You can measure your heart rate using either the
handgrip pulse sensor or an optional chest pulse
sensor (see page 22 for information about the
optional chest pulse sensor). Note: If you hold the
handgrip pulse sensor and wear the chest pulse
sensor at the same time, the console will not display your heart rate accurately.
If there are
sheets of plastic
on the metal contacts on the
handgrip pulse
sensor, remove
the plastic. To
measure your
heart rate, hold the
handgrip pulse
sensor with your
palms resting
against the metal contacts. Avoid moving your
hands or gripping the contacts tightly.
Contacts
If the pedals do not move for several seconds, a
tone will sound and the console will pause.
If the pedals do not move for several minutes and
the buttons are not pressed, the console will turn
off and the display will be reset.
When you are finished exercising, switch the
power switch to the off position and unplug the
power cord. IMPORTANT: If you do not do this,
the electrical components on the elliptical may
wear prematurely.
19
Page 20
HOW TO USE A PRESET WORKOUT
1. Begin pedaling or press any button on the
onsole to turn on the console.
c
ee HOW TO TURN ON THE POWER on page
S
18.
2. Select a preset workout.
To select a preset
workout, press the
Performance
Workouts button or
the Wt. Loss
Workouts button
repeatedly until the
name of the
desired workout
appears in the display.
The workout duration, the maximum speed, and a
profile of the resistance levels will also appear in
the display.
3. Begin pedaling to start the workout.
Each workout is divided into 20, 30, or 45 oneminute segments. One resistance level and one
target speed is programmed for each segment.
Note: The same resistance level and/or target
speed may be programmed for consecutive segments.
Profile
As you exercise,
keep your pedaling
speed near the tar-
et speed for the
g
current segment. At
he beginning of
t
each segment, the target speed for the segment
will flash in the display.
IMPORTANT: The target speed is intended only
to provide motivation. Your actual pedaling
speed may be slower than the target speed.
Make sure to pedal at a speed that is comfortable for you.
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by pressing the Resistance buttons.
IMPORTANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
The workout will continue in this way until the last
segment ends. To stop the workout at any time,
stop pedaling. A tone will sound and the time will
stop counting. To restart the workout, simply
resume pedaling.
4. Follow your progress with the display.
See step 4 on page 18.
5. Measure your heart rate if desired.
The resistance level for the first segment will
appear in the display and the target speed for the
first segment will flash in the display for a few seconds.
During the workout, the workout profile will show
your progress (see the drawing above). The flashing segment of the profile represents the current
segment of the workout. The height of the flashing
segment indicates the resistance level for the current segment.
At the end of each segment of the workout, a
series of tones will sound and the next segment of
the profile will begin to flash. If a different resistance level and/or target speed is programmed for
the next segment, the resistance level and/or target speed will appear in the display for a few
seconds to alert you. The resistance of the pedals
will then change.
See step 5 on page 19.
6. Turn on the fan if desired.
See step 6 on page 19.
7. When you are finished exercising, unplug the
power cord.
See step 7 on page 19.
20
Page 21
HOW TO USE AN IFIT WORKOUT
HOW TO USE THE SOUND SYSTEM
iFit cards are available separately. To purchase iFit
ards, go to www.iFit.com or see the front cover of this
c
manual. iFit cards are also available at select stores.
1. Begin pedaling or press any button on the
console to turn on the console.
See HOW TO TURN ON THE POWER on page
18.
2.
Insert an iFit card and select a workout.
To use an iFit workout, insert an iFit card into the
iFit slot located on the side of the console; make
sure that the iFit card is oriented so that the metal
contacts are face down and are facing the slot.
When the iFit card is properly inserted, the indicator next to the slot will light and text will appear in
the display.
iFit Slot
iFit Card
Next, select the desired workout on the iFit card
by pressing the increase and decrease buttons
next to the iFit slot.
A moment after you select a workout, the voice of
a personal trainer will begin guiding you through
your workout.
iFit workouts function in the same way as preset
workouts. To use the workout, see steps 3 to 7 on
page 20.
3.
When you are finished exercising, remove the
iFit card.
To play music or audio books through the console
ound system while you exercise, plug the included
s
audio cable into the jack on the console and into a
ack on your MP3 player or CD player; make sure
j
that the audio cable is fully plugged in.
Next, press the play button on your MP3 player or CD
player. Adjust the volume level using the volume control on your MP3 player or CD player.
HOW TO CHANGE CONSOLE SETTINGS
The console features a user mode that allows you to
select a backlight option for the console and to view
console usage information.
To select the user mode, press and hold down the
Display button for a few seconds until the user mode
information appears in the display.
The console has three
backlight options. The
ON option keeps the
backlight on while the
console is on. The
AUTO option keeps
the backlight on only
while you are pedaling.
The OFF option turns
the backlight off.
The upper display will show the currently selected
backlight option. Press the Resistance increase button
repeatedly to select the desired backlight option.
The lower left display will show the total number of
hours that the console has been used since the elliptical was purchased.
Press the Display button to save the console settings
and exit the user mode.
Remove the iFit card when you are finished exercising. Store the iFit card in a secure place.
21
Page 22
THE OPTIONAL CHEST PULSE SENSOR
The optional chest pulse sensor provides hands-free
peration and continuously monitors your heart rate
o
during your workouts. To purchase the optional
hest pulse sensor, see the front cover of this
c
manual.
22
Page 23
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the elliptical regularly.
eplace any worn parts immediately.
R
To clean the elliptical, use a damp cloth and a small
amount of mild soap. IMPORTANT: To avoid damage
o the console, keep liquids away from the con-
t
sole and keep the console out of direct sunlight.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
If the handgrip pulse sensor does not function properly, see step 5 on page 19.
HOW TO CALIBRATE THE RAMP
If the ramp is not functioning properly, the ramp may
need to be calibrated. To calibrate the ramp, press
and hold the Resistance increase and decrease buttons for several seconds until the test mode appears
in the display.
At the same time, press the Resistance increase and
decrease buttons twice. Press the Vol increase or
decrease button to calibrate the ramp. The ramp will
move upward and downward as it calibrates.
When the ramp stops moving, the ramp is calibrated.
Then, at the same time, press the Resistance
increase and decrease buttons repeatedly to exit the
calibration mode.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
Next, look into the access opening and locate the
eed Switch (69). Rotate the Large Pulley (74) until a
R
Pulley Magnet (75) is aligned with the Reed Switch.
75
106
69
Next, loosen, but do not remove, the indicated M4 x
16mm Screw (106). Slide the Reed Switch (69)
slightly toward or away from the Pulley Magnet (75).
Then, retighten the M4 x 16mm Screw.
Plug in the power cord and rotate the large pulley for a
moment. Repeat these actions until the console displays correct feedback. When the reed switch is
correctly adjusted, reattach the access cover.
74
To adjust the reed switch, first unplug the power cord.
Using a flat screwdriver, release the tabs on the
Access Cover (20) and pry the Access Cover upward
off the elliptical.
20
23
Page 24
OW TO ADJUST THE DRIVE BELT
H
If you can feel the pedals slip while you are pedaling,
even when the resistance is adjusted to the highest
evel, the drive belt may need to be adjusted.
l
o adjust the drive belt, first unplug the power cord.
T
Using a flat screwdriver, release the tabs on the
Access Cover (20) and pry the Access Cover upward
off the elliptical.
20
152
oosen the Pivot Screw (97). Tighten the Belt
L
Adjustment Screw (85) until the Drive Belt (38) is tight.
When the Drive Belt is tight, tighten the Pivot Screw.
8
3
97
85
13
153
50
Next, lift the Latch (50) on the underside of the Left
Pedal Arm (13), and then lift the Left Pedal Arm off the
left Pedal Arm Sleeve (46).
Then, remove the M4 x 16mm Round Head Screws
(152) and the M4 x 42mm Screws (153) from the
Right and Left Shields (18, 19). (Note: Not all Screws
are shown. Be sure to note which size Screws come
from which holes.) Then, carefully remove the Left
Shield.
46
153
19,18
When you are finished, reattach the left shield, replace
the left pedal arm, and reattach the access cover.
Then, plug in the power cord.
24
Page 25
EXERCISE GUIDELINES
WARNING: B
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determining heart rate trends in general.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
efore beginning this
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
ody uses carbohydrate calories for energy. Only after
b
the first few minutes of exercise does your body begin
o use stored fat calories for energy. If your goal is to
t
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
WORKOUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of
stretching. Stretching increases the flexibility of your
muscles and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
25
Page 26
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
4. Quadriceps Stretch
1
2
3
4
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
5
26
Page 27
PART LIST M
Key No. Qty. Description Key No. Qty. Description
odel No. NTEVEL89909.2 R0111A
11Main Frame
21Folding Frame
31Front Stabilizer
4
51Upright
61Right Upper Body Leg
71Left Upper Body Leg
81Right Upper Body Arm
91Left Upper Body Arm
10 1 Right Handlebar
11 1 Left Handlebar
12 1 Right Pedal Arm
13 1 Left Pedal Arm
14 1 Right Pedal
15 1 Left Pedal
16 2 Wheel Cap
17 2 Disc
18 1 Right Shield
19 1 Left Shield
20 1 Access Cover
21 1 Right Frame Cover
22 1 Left Frame Cover
23 6 Double Tree Fastener
24 1 Front Upright Cover
25 1 Rear Upright Cover
26 1 Accessory Tray
27 1 Top Cover
28 2 Pedal Arm Cap
29 18 Mount w/Screw
30 2 Magnet Cover
31 4 Pedal Arm Magnet
32 2 Pedal Arm Roller
33 1 Console
34 2 Pulse Sensor/Wire
35 2 Handgrip
36 2 Wheel
37 2 Stabilizer Cap
38 1 Drive Belt
39 2 Crank Arm
40 2 Hairpin Cotter Pin
41 3 Leveling Foot
42 1 Latch Bracket
43 1 Right Link Arm
44 2 Lift Bracket
45 2 Lift Axle Bushing
46 2 Pedal Arm Sleeve
47 2 Inner Sleeve Bushing
48 1 Upright Axle
49 2 Latch Housing
50 2 Latch
1 Rear Stabilizer
51 2 Large Latch Spring
52 2 Latch Insert
53 4 Long Latch Spring
4 16 Arm/Leg Bushing
5
55 4 M4 x 16mm Flat Head Screw
56 6 Small Axle Cover
57 2 Upright Bushing
58 2 Outer Sleeve Bushing
59 1 Audio Cable
60 1 Wire Harness
61 1 Flywheel
62 4 M6 x 50mm Patch Screw
63 1 Frame Axle
64 4 Main Frame Bushing
65 1 Latch Bracket Axle
66 1 Latch Bracket Spring
67 1 Latch Button
68 1 Button Housing
69 1 Reed Switch/Wire
70 1 Clamp
71 1 Crank Hub
72 1 Crank
73 1 Crank Spacer
74 1 Large Pulley
75 2 Pulley Magnet
76 2 Folding Frame Bearing
77 1 Idler
78 1 Resistance Motor
79 1 Resistance Arm
80 1 Resistance Wheel
81 1 Resistance Bracket
82 1 Motor Bracket
83 1 C-magnet Bracket
84 1 Flywheel Axle
85 1 Belt Adjustment Screw
86 8 M8 x 28mm Patch Screw
87 2 Crank Snap Ring
88 1 C-magnet Bracket Bolt
89 4 Motor Screw
90 1 M5 x 7mm Screw
91 1 M3.5 x 12mm Screw
92 1 M6 Locknut
93 1 Lift Arm Axle
94 2 M8 Jam Nut
95 10 M8 Washer
96 1 M6 Washer
97 1 Pivot Screw
98 2 Motor Bracket Screw
99 1 Idler Bolt
100 4 M10 x 95mm Patch Screw
27
Page 28
ey No. Qty. Description Key No. Qty. Description
K
101 3 Small Pedal Arm Snap Ring
02 16 M8 x 16mm Patch Screw
1
103 14 M8 Split Washer
04 2 Lift Arm Snap Ring
1
105 2 Pulse Wire
106 11 M4 x 16mm Screw
107 4 M10 x 20mm Button Screw
108 6 M10 Washer
109 8 M8 x 16mm Button Screw
110 2 M8 x 23.5mm x 1mm Washer
111 4 M6 x 12mm Patch Screw
112 8 M6 Washer
113 2 Large Axle Cover
114 2 Link Arm Axle
115 1 Power Switch
116 1 Receptacle
117 1 Flywheel Bearing
118 2 Wave Washer
119 1 Power Cord
120 1 Control Board
121 2 M8 x 25mm Patch Screw
122 1 3/8" x 1" Flange Screw
123 1 Control Box Cover
124 1 Control Box
125 1 Transformer
126 2 M10 Locknut
127 2 Long C-pin
128 2 Short C-pin
129 2 M4 x 12mm Screw
130 1 Ramp
131 1 Ramp Cover
132 4 Ramp Bushing
133 1 Ramp Axle
134 1 Lift Motor
35 1 Motor Wire Harness
1
136 2 Ramp Roller
37 1 Long Motor Axle
1
138 1 Short Motor Axle
139 2 Lift Axle Washer
140 2 Motor Spacer
141 2 Lift Axle Screw
142 1 Left Lift Arm
143 1 Right Lift Arm
144 1 Left Link Arm
145 1 Motor Power Wire Harness
146 4 #6 x 3/8" Screw
147 1 Frame Wire Harness
148 1 Ground Wire
149 4 M8 x 35mm Patch Screw
150 4 M8 x 38mm Screw
151 1 UK Power Cord
152 12 M4 x 16mm Round Head Screw
153 4 M4 x 42mm Screw
154 4 M4 x 8mm Screw
155 2 Large Pedal Arm Snap Ring
156 8 M4 x 19mm Screw
157 2 Pedal Pad
158 1 Right Gel Pad
159 1 Left Gel Pad
160 1 M5 Washer
161 2 Adjustment Nut
*–Blue Wire
*–White Wire
*–Userʼs Manual
*–Assembly Tool
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
28
Page 29
EXPLODED DRAWING A M
149
95
149
25
26
6
8
102
54
95
102
34
59
35
156
54
57
118
57
118
48
54
34
33
54
95
102
102
149
95
50
51
52
49
106
127
53
95
35
9
7
56
144
54
54
54
54
54
128
121
95
113
58
47
46
32
101
32
101
121
95
113
47
46
58
54
54
127
106
49
51
52
50
53
128
43
149
114
56
95
114
56
54
54
54
56
5
24
109
95
56
27
28
13
112
111
62
30
31
31
28
30
111
12
62
112
31
31
62
111
112
62
112
105
156
23
102
10
102
102
11
23
103
103
103
103
103
109
154
154
156
155
155
15
157
159
14
157
158
odel No. NTEVEL89909.2 R0111A
29
Page 30
67
42
110
109
65
109
66
75
75
150
150
87
76
73
74
82
96
78
89
80
91
77
88
94
84
94
98
97
92
99
76
87
71
86
86
68
55
106
70
69
125
120
124
123
146
106
129
64
108
107
63
108
110
72
39
86
100
119
147
107
38
61
115
116
2
37
4
37
122
39
107
1
64
41
16
100
36
36
126
3
126
16
134
41
41
64
60
148
135
145
107
133
131
130
29
29
29
29
29
85
132
132
132
108
40
137
45
141
139
136
104
143
103
102
102
102
103
140
109
109
44
44
104
136
141
139
142
45
138
40
93
117
108
108
108
151
90
81
79
83
160
161
101
EXPLODED DRAWING B M
odel No. NTEVEL89909.2 R0111A
30
Page 31
EXPLODED DRAWING C M
17
17
21
152
152
152
29
29
29
29
29
20
152
153
152
152
19
153
18
153
153
22
152
152
152
152
23
odel No. NTEVEL89909.2 R0111A
31
Page 32
ORDERING REPLACEMENT PARTS
o order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to
T
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
RECYCLING INFORMATION
This electronic product must not be disposed of in municipal waste. To preserve the environment, this product must be recycled after its useful life as
required by law.
Please use recycling facilities that are authorized to collect this type of waste in your
area. In doing so, you will help to conserve natural resources and improve European
standards of environmental protection. If you require more information about safe and
correct disposal methods, please contact your local city office or the establishment
where you purchased this product.
Part No. 307556 R0111A Printed in China © 2011 ICON IP, Inc.
Loading...