Nokia G240WF User Guide

Download

7368 ISAM ONT G-240W-F Product Guide

DRAFT

7368 Intelligent Services Access Manager ONT

7368 ISAM ONT G-240W-F Product Guide

Edition 01

Issue: 01

Nokia — Proprietary and confidential Use pursuant to applicable agreements

7368 ISAM ONT G-240W-F Product Guide

DRAFT

Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners.

The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein.

Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide Preface

DRAFT

1Preface

This preface provides general information about the documentation set for optical network terminals (ONTs).

1.1 Scope

This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the current release.

1.2 Audience

This documentation set is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the ONTs.

1.3 Required knowledge

The reader must be familiar with general telecommunications principles.

1.4 Acronyms and initialisms

The expansions and optional descriptions of most acronyms and initialisms appear in the glossary.

1.5 Assistance and ordering phone numbers

Nokia provides global technical support through regional call centers. Phone numbers for the regional call centers are available at the following URL: http://support.alcatel-lucent.com

For ordering information, contact your Nokia sales representative.

Issue: 01 Edition 01 3

Preface

DRAFT

7368 ISAM ONT G-240W-F Product Guide

1.6 Nokia quality processes

Nokia’s ONT quality practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met. The customer or its representatives may be allowed to perform on-site quality surveillance audits, as agreed upon during contract negotiations

1.7 Safety information

For safety information, see the appropriate safety guidelines chapter.

1.8 Documents

Documents are available using ALED or OLCS.

Procedure 1 To download a ZIP file package of the customer documentation

1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you

are a new user and require access to this service, please contact your Nokia sales representative.

2 From the Technical Content for drop-down menu, choose the product.

3 Click on Downloads: Electronic Delivery.

4 Choose Documentation from the drop-down menu and click Next.

5 Select the image from the drop-down menu and click Next.

6 Follow the on-screen directions to download the file.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide Preface

DRAFT

Procedure 2 To access individual documents

Individual PDFs of customer documents are also accessible through the Nokia Customer Support website.

1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you

are a new user and require access to this service, please contact your Nokia sales representative.

2 From the Technical Content for drop-down menu, choose the product.

3 Click on Manuals and Guides to display a list of customer documents by title and part

number. You can filter this list using the Release drop-down menu.

4 Click on the PDF to open or save the file.

1.9 Special information

The following are examples of how special information is presented in this document.

Danger — Danger indicates that the described activity or

situation may result in serious personal injury or death; for example, high voltage or electric shock hazards.

Warning — Warning indicates that the described activity or

situation may, or will, cause equipment damage or serious performance problems.

Caution — Caution indicates that the described activity or

situation may, or will, cause service interruption.

Note — A note provides information that is, or may be, of

special interest.

Issue: 01 Edition 01 5

Preface

DRAFT

1.9.1 Procedures with options or substeps

When there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals.

Procedure 3 Example of options in a procedure

At step 1, you can choose option a or b. At step 2, you must do what the step indicates.

1 This step offers two options. You must choose one of the following:

a This is one option.

b This is another option.

2 You must perform this step.

7368 ISAM ONT G-240W-F Product Guide

Procedure 4 Example of required substeps in a procedure

At step 1, you must perform a series of substeps within a step. At step 2, you must do what the step indicates.

1 This step has a series of substeps that you must perform to complete the step. You must

perform the following substeps:

i This is the first substep.

ii This is the second substep.

iii This is the third substep.

2 You must perform this step.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide Preface

DRAFT

1.10 Multiple PDF document search

You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file.

Note — The PDF files in which you search must be in the same

folder.

Procedure 5 To search multiple PDF files for a common term

1 Open Adobe Acrobat Reader.

2 Choose Edit→Search from the Acrobat Reader main menu. The Search PDF panel appears.

3 Enter the search criteria.

4 Click on the All PDF Documents In radio button.

5 Select the folder in which to search using the drop-down menu.

6 Click on the Search button.

Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol.

Issue: 01 Edition 01 7

Preface

DRAFT

7368 ISAM ONT G-240W-F Product Guide

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide

DRAFT

1 Preface.............................................................................................3

1.1 Scope ..........................................................................................................3

1.2 Audience......................................................................................................3

1.3 Required knowledge....................................................................................3

1.4 Acronyms and initialisms .............................................................................3

1.5 Assistance and ordering phone numbers ....................................................3

1.6 Nokia quality processes...............................................................................4

1.7 Safety information........................................................................................ 4

1.8 Documents ..................................................................................................4

1.9 Special information ......................................................................................5

1.9.1 Procedures with options or substeps...........................................................6

1.10 Multiple PDF document search ...................................................................7

2 ETSI ONT safety guidelines .........................................................17

2.1 Safety instructions .....................................................................................17

2.1.1 Safety instruction boxes ............................................................................17

2.1.2 Safety-related labels..................................................................................18

2.2 Safety standards compliance ....................................................................19

2.2.1 EMC, EMI, and ESD compliance...............................................................19

2.2.2 Equipment safety standard compliance.....................................................19

2.2.3 Environmental standard compliance .........................................................20

2.2.4 Laser product standard compliance ..........................................................20

2.2.5 Resistibility requirements compliance .......................................................20

2.2.6 Acoustic noise emission standard compliance..........................................20

2.3 Electrical safety guidelines ........................................................................20

2.3.1 Power supplies ..........................................................................................21

2.3.2 Cabling ......................................................................................................21

2.3.3 Protective earth .........................................................................................21

2.4 ESD safety guidelines ...............................................................................21

2.5 Laser safety guidelines..............................................................................21

2.5.1 Laser classification .................................................................................... 22

2.5.1.1 Laser warning labels..................................................................................22

2.5.2 Transmit optical output ..............................................................................24

2.5.3 Normal laser operation ..............................................................................24

2.5.4 Location class............................................................................................25

2.6 Environmental requirements......................................................................25

3 ETSI environmental and CRoHS guidelines...............................27

3.1 Environmental labels .................................................................................27

3.1.1 Overview....................................................................................................27

3.1.2 Environmental related labels .....................................................................27

3.1.2.1 Products below Maximum Concentration Value (MCV) label....................27

3.1.2.2 Products containing hazardous substances above Maximum

Concentration Value (MCV) label ..............................................................28

3.2 Hazardous Substances Table (HST).........................................................29

3.3 Other environmental requirements ............................................................30

Issue: 01 Edition 01 9

7368 ISAM ONT G-240W-F Product Guide

DRAFT

3.3.1 ONT environmental requirements .............................................................30

3.3.2 Storage ......................................................................................................30

3.3.3 Transportation ...........................................................................................30

3.3.4 Stationary use............................................................................................30

3.3.5 Thermal limitations ....................................................................................30

3.3.6 Material content compliance......................................................................31

3.3.7 End-of-life collection and treatment ...........................................................31

4 ANSI ONT safety guidelines ........................................................33

4.1 Safety instructions .....................................................................................33

4.1.1 Safety instruction boxes in customer documentation ................................ 33

4.1.2 Safety-related labels..................................................................................34

4.2 Safety standards compliance ....................................................................35

4.2.1 EMC, EMI, and ESD standards compliance..............................................36

4.2.2 Equipment safety standard compliance.....................................................36

4.2.3 Environmental standards compliance........................................................37

4.2.4 Laser product standards compliance.........................................................37

4.2.5 Resistibility requirements compliance .......................................................38

4.3 Laser safety guidelines..............................................................................38

4.3.1 Laser warning labels..................................................................................38

4.3.2 Laser classification .................................................................................... 40

4.3.3 Transmit optical output ..............................................................................41

4.3.4 Normal laser operation ..............................................................................41

4.3.5 Location class............................................................................................41

4.4 Electrical safety guidelines ........................................................................42

4.4.1 Power supplies ..........................................................................................42

4.4.2 Cabling ......................................................................................................42

4.4.3 Protective earth .........................................................................................42

4.5 ESD safety guidelines ...............................................................................42

4.6 Environmental requirements......................................................................43

5 G-240W-F unit data sheet.............................................................45

5.1 G-240W-F part numbers and identification................................................46

5.2 G-240W-F general description ..................................................................47

5.2.1 TR-069 support..........................................................................................48

5.2.2 TR-104 parameter extension support for voice service.............................49

5.2.3 TR-181 Wi-Fi objects adapted in TR-098 ..................................................49

5.2.4 Mobile offload support ...............................................................................49

5.2.5 Bridged Residential Gateway (BRG) support ............................................50

5.2.6 Support for soft GRE tunnels.....................................................................50

5.2.6.1 GRE........................................................................................................... 51

5.2.6.2 Soft GRE ...................................................................................................51

5.3 G-240W-F software and installation feature support .................................52

5.4 G-240W-F interfaces and interface capacity .............................................53

5.4.1 G-240W-F connections and components ..................................................53

5.5 G-240W-F LEDs ........................................................................................55

5.6 G-240W-F detailed specifications..............................................................57

5.7 G-240W-F GEM ports and T-CONTs ........................................................58

5.8 G-240W-F performance monitoring statistics ............................................58

5.9 G-240W-F functional blocks ......................................................................60

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide

DRAFT

5.10 G-240W-F standards compliance..............................................................62

5.10.1 Energy-related products standby and off modes compliance....................63

5.11 G-240W-F special considerations .............................................................63

5.11.1 Wi-Fi service..............................................................................................63

5.11.1.1 Wi-Fi physical features .............................................................................. 64

5.11.1.2 Wi-Fi standards and certifications .............................................................64

5.11.1.3 Wi-Fi GUI features.....................................................................................64

5.11.2 G-240W-F ONT considerations and limitations .........................................64

6 Install a G-240W-F indoor ONT....................................................67

6.1 Purpose .....................................................................................................67

6.2 General......................................................................................................67

6.3 Prerequisites..............................................................................................67

6.4 Recommended tools..................................................................................67

6.5 Safety information......................................................................................68

6.6 Procedure ..................................................................................................69

7 Replace a G-240W-F indoor ONT ................................................75

7.1 Purpose .....................................................................................................75

7.2 General......................................................................................................75

7.3 Prerequisites..............................................................................................75

7.4 Recommended tools..................................................................................75

7.5 Safety information......................................................................................76

7.6 Procedure ..................................................................................................77

8 Configure a G-240W-F indoor ONT .............................................83

8.1 General......................................................................................................83

8.2 HGU mode GUI configuration....................................................................83

8.2.1 Login..........................................................................................................83

8.2.2 Device and connection status....................................................................84

8.2.3 Network configuration................................................................................94

8.2.4 Security configuration ..............................................................................115

8.2.5 Application configuration .........................................................................124

8.2.6 Maintenance ............................................................................................131

8.2.7 RG troubleshooting counters...................................................................143

8.3 SFU mode GUI configuration ..................................................................145

8.3.1 Login........................................................................................................145

8.3.2 Device and connection status..................................................................146

8.3.3 Maintenance ............................................................................................148

8.4 Operator ID..............................................................................................150

9 ONT configuration file over OMCI .............................................153

9.1 Purpose ...................................................................................................153

9.2 Supported configuration file types ...........................................................153

9.2.1 Filename conventions..............................................................................155

9.3 ONT configuration file over OMCI ...........................................................155

Issue: 01 Edition 01 11

7368 ISAM ONT G-240W-F Product Guide

DRAFT

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide

DRAFT

List of figures

2 ETSI ONT safety guidelines .........................................................17

Figure 1 PSE certification........................................................................................19

Figure 2 Laser product label....................................................................................22

Figure 3 Laser classification label............................................................................23

Figure 4 Laser warning labels..................................................................................24

3 ETSI environmental and CRoHS guidelines...............................27

Figure 5 Products below MCV value label...............................................................28

Figure 6 Products above MCV value label ..............................................................29

Figure 7 Recycling/take back/disposal of product symbol....................................... 31

4 ANSI ONT safety guidelines ........................................................33

Figure 8 Sample safety label on the ONT equipment..............................................35

Figure 9 Sample laser product label showing CDRH 21 CFR compliance..............37

Figure 10 Laser product label ....................................................................................39

Figure 11 Laser classification label............................................................................39

Figure 12 Laser warning labels..................................................................................40

Figure 13 Sample laser product safety label on the ONT equipment ........................41

5 G-240W-F unit data sheet.............................................................45

Figure 14 SoftGRE-based architecture......................................................................52

Figure 15 G-240W-F indoor ONT physical connections (back view).........................54

Figure 16 G-240W-F ONT Reset, LED, WLAN, and WPS buttons and fiber

optic connection (bottom and side view) ...................................................54

Figure 17 G-240W-F indoor ONT LEDs ....................................................................56

Figure 18 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and

without RF video........................................................................................61

Figure 19 G-240W-F ONT hardware block................................................................61

6 Install a G-240W-F indoor ONT....................................................67

Figure 20 G-240W-F indoor ONT wall mounting holes (bottom view) .......................69

Figure 21 G-240W-F indoor ONT connections (back view).......................................70

Figure 22 G-240W-F ONT Reset, LED, WLAN, and WPS buttons and fiber

optic connection (bottom and side view) ...................................................71

Figure 23 G-240W-F indoor ONT with fiber cover open ............................................72

7 Replace a G-240W-F indoor ONT ................................................75

Figure 24 G-240W-F indoor ONT Reset, LED, WLAN, and WPS buttons

(side)..........................................................................................................77

Figure 25 G-240W-F indoor ONT connections (back view).......................................78

Figure 26 G-240W-F indoor ONT fiber optic port (bottom view)................................79

8 Configure a G-240W-F indoor ONT .............................................83

Figure 27 Web login window......................................................................................84

Figure 28 Device Information window........................................................................85

Figure 29 LAN status window ....................................................................................86

Figure 30 WAN status window...................................................................................88

Figure 31 WAN status IPv6 window ..........................................................................89

Issue: 01 Edition 01 13

7368 ISAM ONT G-240W-F Product Guide

DRAFT

Figure 32 Home networking information window.......................................................90

Figure 33 Optics module status window ....................................................................91

Figure 34 Voice Information window..........................................................................93

Figure 35 LAN network window .................................................................................95

Figure 36 LAN IPv6 network window.........................................................................97

Figure 37 WAN network window................................................................................98

Figure 38 WiFi network window...............................................................................100

Figure 39 Wireless Schedule window......................................................................102

Figure 40 Routing network window..........................................................................103

Figure 41 DNS network window ..............................................................................105

Figure 42 TR-069 network window..........................................................................106

Figure 43 GRE Tunnel window................................................................................107

Figure 44 QoS Config window (L2)..........................................................................109

Figure 45 QoS Config window (L3)..........................................................................110

Figure 46 US Classifier Policy window ....................................................................112

Figure 47 US Classifier window...............................................................................113

Figure 48 US Classifier Rules window.....................................................................114

Figure 49 Firewall window .......................................................................................116

Figure 50 MAC filter window....................................................................................117

Figure 51 IP filter window ........................................................................................118

Figure 52 URL Filter window ...................................................................................119

Figure 53 Parental Control window..........................................................................120

Figure 54 DMZ and ALG window.............................................................................122

Figure 55 Access Control window ...........................................................................123

Figure 56 Port forwarding window ...........................................................................125

Figure 57 Port Triggering window............................................................................126

Figure 58 DDNS window .........................................................................................127

Figure 59 NTP window ............................................................................................128

Figure 60 USB storage window ...............................................................................129

Figure 61 UPnP and DLNA window.........................................................................130

Figure 62 Password window....................................................................................132

Figure 63 LOID Config window................................................................................133

Figure 64 SLID configuration window......................................................................134

Figure 65 Device management window...................................................................135

Figure 66 Backup and Restore window ...................................................................136

Figure 67 Firmware upgrade window ......................................................................137

Figure 68 Reboot window ........................................................................................138

Figure 69 Factory default window............................................................................139

Figure 70 Diagnose window ....................................................................................140

Figure 71 Log window..............................................................................................141

Figure 72 PPPoE Diagnostics window ....................................................................142

Figure 73 PPPoE diagnostics results ......................................................................143

Figure 74 RG Troubleshooting Counters window....................................................144

Figure 75 Web login window....................................................................................146

Figure 76 Device Information window......................................................................147

Figure 77 Password window....................................................................................148

Figure 78 LOID configuration window......................................................................149

Figure 79 SLID configuration window......................................................................150

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide

DRAFT

List of tables

2 ETSI ONT safety guidelines .........................................................17

Table 1 Safety labels ..............................................................................................18

4 ANSI ONT safety guidelines ........................................................33

Table 2 Safety labels ..............................................................................................34

5 G-240W-F unit data sheet.............................................................45

Table 3 Identification of G-240W-F indoor ONTs ...................................................46

Table 4 G-240W-F indoor ONT interface connection capacity...............................53

Table 5 G-240W-F indoor ONT physical connections ............................................55

Table 6 G-240W-F indoor ONT LEDs ....................................................................56

Table 7 G-240W-F indoor ONT physical specifications..........................................57

Table 8 G-240W-F indoor ONT power consumption specifications .......................57

Table 9 G-240W-F indoor ONT environmental specifications ................................58

Table 10 G-240W-F indoor ONT capacity for GEM ports and T-CONTs .................58

Table 11 Package P ONTs ONTENET performance monitoring statistics...............59

Table 12 Package P ONTs ONTL2UNI performance monitoring statistics ..............59

Table 13 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI,

PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP

performance monitoring statistics..............................................................59

Table 14 Package P ONTs PONONTTC aggregate performance monitoring

statistics.....................................................................................................60

Table 15 G-240W-F ONT considerations and limitations .........................................64

8 Configure a G-240W-F indoor ONT .............................................83

Table 16 Device Information parameters .................................................................85

Table 17 LAN status parameters..............................................................................86

Table 18 WAN status parameters ............................................................................88

Table 19 WAN status IPv6 parameters ....................................................................89

Table 20 Home networking parameters ...................................................................91

Table 21 Optics module status parameters..............................................................92

Table 22 Voice Information parameters ...................................................................93

Table 23 LAN network parameters...........................................................................95

Table 24 LAN IPv6 network parameters...................................................................97

Table 25 WAN network parameters .........................................................................99

Table 26 WiFi network parameters.........................................................................100

Table 27 Routing network parameters ...................................................................104

Table 28 DNS network parameters ........................................................................105

Table 29 TR-069 network parameters....................................................................106

Table 30 GRE Tunnel parameters..........................................................................107

Table 31 QoS Config parameters...........................................................................111

Table 32 US Classifier Policy parameters ..............................................................112

Table 33 US Classifier parameters.........................................................................113

Table 34 US Classifier Rules parameters ..............................................................114

Table 35 Firewall parameters .................................................................................116

Table 36 MAC filter parameters..............................................................................117

Table 37 IP filter parameters ..................................................................................118

Issue: 01 Edition 01 15

7368 ISAM ONT G-240W-F Product Guide

DRAFT

Table 38 URL Filter parameters .............................................................................120

Table 39 Parental control parameters ....................................................................121

Table 40 DMZ and ALG parameters ......................................................................122

Table 41 Access control parameters ......................................................................123

Table 42 Port forwarding parameters .....................................................................125

Table 43 Port triggering parameters.......................................................................126

Table 44 DDNS parameters ...................................................................................128

Table 45 NTP parameters ......................................................................................129

Table 46 USB storage parameters .........................................................................130

Table 47 Password parameters..............................................................................132

Table 48 LOID configuration parameters ...............................................................133

Table 49 SLID configuration parameters................................................................134

Table 50 Device management parameters ............................................................135

Table 51 PPPoE diagnostics results parameters ...................................................143

Table 52 RG Troubleshooting Counters parameters..............................................144

Table 53 Device Information parameters ...............................................................147

Table 54 Password parameters..............................................................................148

Table 55 SLID configuration parameters................................................................150

9 ONT configuration file over OMCI .............................................153

Table 56 Supported configuration files ...................................................................154

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ETSI ONT safety guidelines

DRAFT

2 ETSI ONT safety guidelines

This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs).

2.1 Safety instructions

This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment.

2.1.1 Safety instruction boxes

The safety instruction boxes are provided in the ONT customer documentation. Observe the instructions to meet safety requirements.

The following is an example of the Danger box.

Danger — Possibility of personal injury.

The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm.

Do not proceed beyond a Danger box until the indicated conditions are fully understood and met.

The following is an example of the Warning box.

Warning 1 — Possibility of equipment damage.

Warning 2 — Possibility of data loss.

The Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-damaging situation or provides essential information to avoid the degradation of system operations or data.

Do not proceed beyond a warning until the indicated conditions are fully understood and met.

Issue: 01 Edition 01 17

ETSI ONT safety guidelines

DRAFT

The following is an example of the Caution box.

The Caution box indicates that the described activity or situation may, or will, cause service interruption.

Do not proceed beyond a caution until the indicated conditions are fully understood and met.

The following is an example of the Note box.

The Note box provides information that assists the personnel working with ONTs. It does not provide safety-related instructions.

7368 ISAM ONT G-240W-F Product Guide

Caution 1 — Possibility of service interruption.

Caution 2 — Service interruption.

Note — Information of special interest.

2.1.2 Safety-related labels

The ONT equipment is labeled with the specific safety instructions and compliance information that is related to a variant of the ONT. Observe the instructions on the safety labels.

Table 1 provides sample safety labels on the ONT equipment.

Table 1 Safety labels

Description Label text

ESD warning Caution: This assembly contains an electrostatic sensitive device.

Laser classification Class 1 laser product

PSE marking These power supplies are Japan PSE certified and compliant with

Figure 1 shows the PSE certification.

Japan VCCI emissions standards.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ETSI ONT safety guidelines

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

Warning

19841

DRAFT

Figure 1 PSE certification

2.2 Safety standards compliance

This section describes the ONT compliance with the European safety standards.

2.2.1 EMC, EMI, and ESD compliance

The ONT equipment complies with the following EMC, EMI, and ESD requirements:

• EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands

• EN 300-386 V1.5.1: Electromagnetic Compatibility and Radio Spectrum Matters

(ERM): Telecommunications Network Equipment; Electromagnetic Compatibility (EMC) requirements; Electrostatic Discharge (ESD) requirements

• EN 55022 (2006): Class B, Information Technology Equipment, Radio

Disturbance Characteristics, limits and methods of measurement

• EN 55024 (2010): Information Technology Equipment, Immunity Characteristics,

limits and methods of measurement

• European Council Directive 2004/108/EC

• EN 300-386 V1.4.1: 2008

• EN 55022:2006 Class B (ONTs)

2.2.2 Equipment safety standard compliance

The ONT equipment complies with the requirements of EN 60950-1, Safety of Information Technology Equipment for use in a restricted location (per R-269).

Issue: 01 Edition 01 19

ETSI ONT safety guidelines

DRAFT

2.2.3 Environmental standard compliance

The ONT equipment complies with the EN 300 019 European environmental standards.

2.2.4 Laser product standard compliance

For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products. If there is an exception to this compliance regulation, you can find this information in the standards compliance section of the unit data sheet in this Product Guide.

2.2.5 Resistibility requirements compliance

7368 ISAM ONT G-240W-F Product Guide

The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to over voltage and overcurrents.

2.2.6 Acoustic noise emission standard compliance

The ONT equipment complies with EN 300 753 acoustic noise emission limit and test methods.

2.3 Electrical safety guidelines

This section provides the electrical safety guidelines for the ONT equipment.

Note 1 — The ONTs comply with the U.S. National Electrical

Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards.

Note 2 — The ONTs comply with BS EN 61140.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ETSI ONT safety guidelines

DRAFT

2.3.1 Power supplies

The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property.

2.3.2 Cabling

The following are the guidelines regarding cables used for the ONT equipment:

• All cables must be approved by the relevant national electrical code.

• The cables for outdoor installation of ONTs must be suitable for outdoor use.

• POTS wiring run outside the subscriber premises must comply with the

requirements of local electrical codes. In some markets, the maximum allowed length of the outside run is 140 feet (43 m). If the outside run is longer, NEC requires primary protection at both the exit and entry points for the wire.

2.3.3 Protective earth

Earthing and bonding of the ONTs must comply with the requirements of local electrical codes.

2.4 ESD safety guidelines

The ONT equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the ONT equipment.

Caution — This equipment is ESD sensitive. Proper ESD

protections should be used when you enter the TELCO Access portion of the ONT.

During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD.

2.5 Laser safety guidelines

Observe the following instructions when you perform installation, operations, and maintenance tasks on the ONT equipment.

Issue: 01 Edition 01 21

ETSI ONT safety guidelines

18455

DRAFT

Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system.

Observe the following danger for laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules.

2.5.1 Laser classification

7368 ISAM ONT G-240W-F Product Guide

Danger — There may be invisible laser radiation at the fiber

optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam.

Danger — Possibility of equipment damage. Risk of eye

damage by laser radiation.

The ONT is classified as a Class 1 laser product based on its transmit optical output.

2.5.1.1 Laser warning labels

The following figures show the labels related to laser product, classification and warning.

Figure 2 shows a laser product label.

Figure 2 Laser product label

Figure 3 shows a laser classification label. Laser classification labels may be provided in other languages.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ETSI ONT safety guidelines

LASER CLASSE 1CLASE 1 DEL LASER

CLASS 1 LASER PRODUCT PRODUCTO LASER CLASE 1

18992

DRAFT

Figure 3 Laser classification label

Figure 4 shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages. The explanatory label provides the following information:

• a warning that calls attention to the invisible laser radiation

• an instruction against staring into the beam or viewing directly with optical

instruments

• wavelength

• normal output power

• maximum output power

Issue: 01 Edition 01 23

ETSI ONT safety guidelines

INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W

Laser Warning Label

CLASS 1 LASER PRODUCT

INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM.

RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE

EVITER TOUTE EXPOSITION AU FAISCEAU

NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE

CLASE 1 DEL LASER

RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL

RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO

Laser Warning Label

18993

DRAFT

Figure 4 Laser warning labels

7368 ISAM ONT G-240W-F Product Guide

2.5.2 Transmit optical output

The maximum transmit optical output of an ONT is +5 dBm.

2.5.3 Normal laser operation

In normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card.

Eyes can be damaged when they exposed to a laser beam. Operating personnel must observe the instructions on the laser explanatory label before plugging in the optical module.

Danger — Risk of eye damage by laser radiation.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ETSI ONT safety guidelines

DRAFT

2.5.4 Location class

Use cable supports and guides to protect the receptacles from strain.

2.6 Environmental requirements

See the ONT technical specification documentation for more information about temperature ranges.

During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue. To avoid condensation caused by rapid changes in temperature and humidity, Nokia recommends:

• The door of the ONT not be opened until temperature inside and outside the

enclosure has stabilized.

• If the door of the ONT must be opened after a rapid change in temperature or

humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation.

• When high humidity is present, installation of a cover or tent over the ONT helps

prevent condensation when the door is opened.

Issue: 01 Edition 01 25

ETSI ONT safety guidelines

DRAFT

7368 ISAM ONT G-240W-F Product Guide

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ETSI environmental and CRoHS guidelines

DRAFT

3 ETSI environmental and CRoHS

guidelines

This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest.

3.1 Environmental labels

This section describes the environmental instructions that are provided with the customer documentation, equipment, and location where the equipment resides.

3.1.1 Overview

CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold and imported in the territory of the mainland of the People’s Republic of China. EIP refers to products and their accessories manufactured by using electronic information technology, including electronic communications products and such subcomponents as batteries and cables.

3.1.2 Environmental related labels

Environmental labels are located on appropriate equipment. The following are sample labels.

3.1.2.1 Products below Maximum Concentration Value (MCV) label

Figure 5 shows the label that indicates a product is below the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). Products with this label are recyclable. The label may be found in this documentation or on the product.

Issue: 01 Edition 01 27

ETSI environmental and CRoHS guidelines

18986

DRAFT

Figure 5 Products below MCV value label

7368 ISAM ONT G-240W-F Product Guide

3.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label

Figure 6 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). The number contained inside the label indicates the Environment-Friendly User Period (EFUP) value. The label may be found in this documentation or on the product.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ETSI environmental and CRoHS guidelines

18985

DRAFT

Figure 6 Products above MCV value label

Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories. These values are based on manufacturers' extensive practical experience of the design, manufacturing, maintenance, usage conditions, operating environments, and physical condition of infrastructure and handsets after years of service. The values reflect minimum values and refer to products operated according to the intended use conditions. See “Hazardous Substances Table (HST)” for more information.

3.2 Hazardous Substances Table (HST)

This section describes the compliance of the OLT and ONT equipment to the CRoHS standard when the product and subassemblies contain hazardous substances beyond the MCV value. This information is found in this user documentation where part numbers for the product and subassemblies are listed. It may be referenced in other OLT and ONT documentation.

In accordance with the People’s Republic of China Electronic Industry Standard Marking for the Control of Pollution Caused by Electronic Information Products (SJ/T11364-2006), customers may access the Nokia Hazardous Substance Table, in Chinese, from the following location:

• http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRo

HS.pdf

Issue: 01 Edition 01 29

ETSI environmental and CRoHS guidelines

DRAFT

3.3 Other environmental requirements

Observe the following environmental requirements when handling the P-OLT or ONT equipment.

3.3.1 ONT environmental requirements

See the ONT technical specification documentation for more information about temperature ranges.

3.3.2 Storage

According to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in Class 1.1, weather-protected, temperature-controlled locations.

7368 ISAM ONT G-240W-F Product Guide

3.3.3 Transportation

According to EN 300-019-1-2 - Class 2.3, transportation of the OLT equipment must be in packed, public transportation with no rain on packing allowed.

3.3.4 Stationary use

According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment must be in a temperature-controlled location, with no rain allowed, and with no condensation allowed.

3.3.5 Thermal limitations

When the OLT is installed in the CO or CEV, install air filters on the P-OLT. The thermal limitations for OLT operation in a CO or CEV are:

• operating temperature: 5°C to 40°C (41°F to 104°F)

• short-term temperature: –5°C to 50°C (23°F to 122°F)

• operating relative humidity: 5% to 85%

• short-term relative humidity: 5% to 95%, but not to exceed 0.024 kg of water/kg

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ETSI environmental and CRoHS guidelines

DRAFT

3.3.6 Material content compliance

European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive applies to electrical and electronic products placed on the EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment. Nokia products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive.

Nokia has implemented a material/substance content management process. The process is described in: Nokia process for ensuring RoHS Compliance (1AA002660031ASZZA). This ensures compliance with the European Union Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2). With the process equipment is assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC) on Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances.

3.3.7 End-of-life collection and treatment

Electronic products bearing or referencing the symbol shown in Figure 7, when put on the market within the European Union (EU), shall be collected and treated at the end of their useful life, in compliance with applicable EU and local legislation. They shall not be disposed of as part of unsorted municipal waste. Due to materials that may be contained in the product, such as heavy metals or batteries, the environment and human health may be negatively impacted as a result of inappropriate disposal.

Note — In the European Union, a solid bar under the symbol for

a crossed-out wheeled bin indicates that the product was put on the market after 13 August 2005.

Figure 7 Recycling/take back/disposal of product symbol

Issue: 01 Edition 01 31

ETSI environmental and CRoHS guidelines

DRAFT

At the end of their life, the OLT and ONT products are subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE).

There can be different requirements for collection and treatment in different member states of the European Union.

In compliance with legal requirements and contractual agreements, where applicable, Nokia will offer to provide for the collection and treatment of Nokia products bearing the logo shown in Figure 7 at the end of their useful life, or products displaced by Nokia equipment offers. For information regarding take-back of equipment by Nokia, or for more information regarding the requirements for recycling/disposal of product, contact your Nokia account manager or Nokia take back support at sustainability.global@nokia.com.

7368 ISAM ONT G-240W-F Product Guide

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines

DRAFT

4 ANSI ONT safety guidelines

This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals or units (ONTs or ONUs) in the North American or ANSI market.

4.1 Safety instructions

This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment.

4.1.1 Safety instruction boxes in customer documentation

The safety instruction boxes are provided in the ONT customer documentation. Observe the instructions to meet safety requirements.

The following is an example of the Danger box.

Danger — Possibility of personal injury.

Do not proceed beyond a Danger box until the indicated conditions are fully understood and met.

The following is an example of the Warning box.

Warning 1 — Possibility of equipment damage.

Warning 2 — Possibility of data loss.

Do not proceed beyond a warning until the indicated conditions are fully understood and met.

Issue: 01 Edition 01 33

ANSI ONT safety guidelines

DRAFT

The following is an example of the Caution box.

The Caution box indicates that the described activity or situation may, or will, cause service interruption.

Do not proceed beyond a caution until the indicated conditions are fully understood and met.

The following is an example of the Note box.

The Note box provides information that assists the personnel working with ONTs. It does not provide safety-related instructions.

7368 ISAM ONT G-240W-F Product Guide

Caution 1 — Possibility of service interruption.

Caution 2 — Service interruption.

Note — Information of special interest.

4.1.2 Safety-related labels

The ONT equipment is labeled with specific safety compliance information and instructions that are related to a variant of the ONT. Observe the instructions on the safety labels.

Table 2 provides examples of the text in the various ONT safety labels.

Table 2 Safety labels

Description Label text

UL compliance Communication service equipment US listed. Type 3R enclosure -

TUV compliance Type 3R enclosure - Rainproof.

ESD warning Caution: This assembly contains electrostatic sensitive device.

Laser classification Class 1 laser product

Laser product compliance This laser product conforms to all applicable standards of 21 CFR

FCC standards compliance Tested to comply with FCC standards for home or office use.

CDRH compliance Complies with 21 CFR 1040.10 and 1040.11 except for deviations

(1 of 2)

Rainproof.

1040.10 at date of manufacture.

pursuant to Laser Notice No. 50, dated June 24, 2007

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines

18533

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la class A est conforme a la norme NMB-003 du Canada

Tested to Comply with FCC Standards

FOR HOME OR OFFICE USE

COMMUNICATION SERVICE EQUIPMENT US LISTED 27FY Type 3R Enclosure - Rainproof

CAUTION

This Assembly Contains Electrostatic Sensitive Devices

DRAFT

Description Label text

Operation conditions This device complies with Part 15 of the FCC Rules. Operation is

Canadian standard compliance (modular ONT)

Canadian standard compliance (outdoor ONT)

CE marking There are various CE symbols for CE compliance.

(2 of 2)

Figure 8 shows a sample safety label on the ONT equipment.

Figure 8 Sample safety label on the ONT equipment

subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES-003.

This Class B digital apparatus complies with Canadian ICES-003.

4.2 Safety standards compliance

This section describes the ONT compliance with North American safety standards.

Warning — Changes or modifications to this unit not expressly

Issue: 01 Edition 01 35

approved by the party responsible for compliance could void the user's authority to operate the equipment.

ANSI ONT safety guidelines

DRAFT

4.2.1 EMC, EMI, and ESD standards compliance

The ONT equipment complies with the following requirements:

• Federal Communications Commission (FCC) CFR 47, Part 15, Subpart B, Class

A requirements for OLT equipment

• GR-1089-CORE requirements, including:

• Section 3 Electromagnetic Interference, Emissions Radiated and Conducted

• Section 3 Immunity, Radiated and Conducted

• Section 2 ESD Discharge Immunity: System Level Electrostatic Discharge and EFT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

7368 ISAM ONT G-240W-F Product Guide

Immunity: Electrically Fast Transients

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is needed.

• Consult the dealer or an experienced radio/TV technician for help.

4.2.2 Equipment safety standard compliance

The ONT equipment complies with the requirements of UL60950-1, Outdoor ONTs to “Communication Service Equipment” (CSE) and Indoor ONTs to Information Technology Equipment (ITE).

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines

FiOS Enabled

To Order FiOS: 888 GET-FiOS or visit Verizon.com

For Service: 888 553-1555

2301 Sugar Bush Rd. Raleigh, NC 27612

No User Serviceable Parts Inside. Refer All Servicing To Qualified Personnel.

Complies with 21 CFR 1040.10 and

1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.

4P92

I.T.E

12VDC 2.5A

22813

DRAFT

4.2.3 Environmental standards compliance

The ONT equipment complies with the following standards:

• GR-63-CORE (NEBS): requirements related to operating, storage, humidity,

altitude, earthquake, office vibration, transportation and handling, fire resistance and spread, airborne contaminants, illumination, and acoustic noise

• GR-487-CORE: requirements related to rain, chemical, sand, and dust

• GR-487 R3-82: requirements related to condensation

• GR-3108: Requirements for Network Equipment in the Outside Plant (OSP)

• TP76200: Common Systems Equipment Interconnections Standards

4.2.4 Laser product standards compliance

The ONT equipment complies with 21 CFR 1040.10 and CFR 1040.11, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007” or to 21 CFR

1040.10 U.S. Center for Devices and Radiological Health (CDRH) of the Food and Drug Administration (FDA) Laser Notice 42 for ONTs containing Class 1 Laser modules certified by original manufactures.

Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user.

a) “Class 1 Laser Product”

b) “Caution – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.”

Figure 9 shows a laser product label.

Figure 9 Sample laser product label showing CDRH 21 CFR compliance

Issue: 01 Edition 01 37

ANSI ONT safety guidelines

DRAFT

4.2.5 Resistibility requirements compliance

The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to overvoltage and overcurrents.

4.3 Laser safety guidelines

Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system.

Observe the following warnings when you perform installation, operations, and maintenance tasks on the ONT equipment.

7368 ISAM ONT G-240W-F Product Guide

Danger — There may be invisible laser radiation at the fiber

optic cable when the cable is removed from the connector. Avoid direct exposure to beam.

Observe the following danger for a laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules.

Danger — Possibility of equipment damage. Risk of eye

damage by laser radiation.

Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user.

a) “Class 1 Laser Product”

b) “Caution – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.”

4.3.1 Laser warning labels

The following figures show sample labels related to laser product, classification and warning.

Figure 10 shows a laser product label.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines

18455

LASER CLASSE 1CLASE 1 DEL LASER

CLASS 1 LASER PRODUCT PRODUCTO LASER CLASE 1

18992

DRAFT

Figure 10 Laser product label

Figure 11 shows a laser classification label. Laser classification labels may be provided in other languages.

Figure 11 Laser classification label

Figure 12 shows a laser warning label and an explanatory label for laser products. Explanatory labels may be provided in other languages. The explanatory label provides the following information:

• a warning that calls attention to the invisible laser radiation

• an instruction against staring into the beam or viewing directly with optical

instruments

• wavelength

• normal output power

• maximum output power

Issue: 01 Edition 01 39

ANSI ONT safety guidelines

INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W

Laser Warning Label

CLASS 1 LASER PRODUCT

INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM.

RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE

EVITER TOUTE EXPOSITION AU FAISCEAU

NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE

CLASE 1 DEL LASER

RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL

RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO

Laser Warning Label

18993

DRAFT

Figure 12 Laser warning labels

7368 ISAM ONT G-240W-F Product Guide

4.3.2 Laser classification

The ONT is classified as a Class 1 laser product based on its transmit optical output.

For Class 1 laser products, lasers are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing.

Figure 13 shows a sample laser product safety label on the ONT equipment.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines

18532

3FE55851ABAA

Model: MFG: MONTH: XX YEAR: XXXX

ICS: XX MRev: XX

MAC:XXXXXXXXXXXX

SN:ALCLXXXXXXXX

FCC ID: XXXXXXXXXXX

This device complies with Part 15 of the FCC Rule. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including intereference that may cause undesired operation.

ASSEMBLED IN CHINA 2301 Sugar Bush Rd

Raleigh, NC 27612

DANGER - Invisible Laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. DANGER - Rayonnement Laser invisible lorsqu’elle est ouverte. Evitee l’expostion direct au faisceau.

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50 dated June 24, 2007

12VDC 3A

I.T.E

Intertek

4006119

CLASS 1 LASER PRODUCT

PRODUIT LASER DE CLASSE 1

DRAFT

Figure 13 Sample laser product safety label on the ONT equipment

4.3.3 Transmit optical output

The maximum transmit optical output of an ONT is +5 dBm.

4.3.4 Normal laser operation

In normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card.

Operating personnel must observe the instructions on the laser explanatory label before plugging in the optical module.

Danger — Risk of eye damage by laser radiation.

4.3.5 Location class

Use cable supports and guides to protect the receptacles from strain.

Issue: 01 Edition 01 41

ANSI ONT safety guidelines

DRAFT

4.4 Electrical safety guidelines

This section provides the electrical safety guidelines for the ONT equipment.

4.4.1 Power supplies

7368 ISAM ONT G-240W-F Product Guide

Note — The ONTs comply with the U.S. National Electrical

Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards.

4.4.2 Cabling

The following are the guidelines regarding cables used for the ONT equipment:

• Use only cables approved by the relevant national electrical code.

• Use cables suitable for outdoor use for outdoor installation of ONTs.

• The ONTs have been evaluated for use with external POTS wiring without primary

protection that may not exceed 140 ft (43 m) in reach. However, the power cable must not exceed 100 ft (31 m).

4.4.3 Protective earth

Earthing and bonding of the ONTs must comply with the requirements of NEC article 250 or local electrical codes.

4.5 ESD safety guidelines

The ONT equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the ONT equipment.

Caution — This equipment is ESD sensitive. Proper ESD

protections should be used when entering the TELCO Access portion of the ONT.

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines

DRAFT

During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD.

Nokia recommends that you prepare the site before you install the ONT equipment. In addition, you must control relative humidity, use static dissipating material for furniture or flooring, and restrict the use of air conditioning.

4.6 Environmental requirements

See the ONT technical specification documentation for temperature ranges for ONTs.

• The door of the ONT not be opened until temperature inside and outside the

enclosure has stabilized.

• If the door of the ONT must be opened after a rapid change in temperature or

humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation.

• When high humidity is present, installation of a cover or tent over the ONT helps

prevent condensation when the door is opened.

Issue: 01 Edition 01 43

ANSI ONT safety guidelines

DRAFT

7368 ISAM ONT G-240W-F Product Guide

Edition 01 Issue: 01

7368 ISAM ONT G-240W-F Product Guide G-240W-F unit data sheet

DRAFT

5 G-240W-F unit data sheet

5.1 G-240W-F part numbers and identification

5.2 G-240W-F general description

5.3 G-240W-F software and installation feature support

5.4 G-240W-F interfaces and interface capacity

5.5 G-240W-F LEDs

5.6 G-240W-F detailed specifications

5.7 G-240W-F GEM ports and T-CONTs

5.8 G-240W-F performance monitoring statistics

5.9 G-240W-F functional blocks

5.10 G-240W-F standards compliance

5.11 G-240W-F special considerations

Issue: 01 Edition 01 45

G-240W-F unit data sheet

DRAFT

5.1 G-240W-F part numbers and identification

Table 3 provides part numbers and identification information for the G-240W-F indoor ONT.

Table 3 Identification of G-240W-F indoor ONTs

7368 ISAM ONT G-240W-F Product Guide

Ordering kit part number

3FE 46649 AA 3FE 46597 AA Package P GPON indoor ONT with two POTS ports, four

3FE 46649 AB 3FE 46597 AA Package P GPON indoor ONT with two POTS ports, four

3FE 46649 AC

Customer-specific

3FE 46649 BA 3FE 46597 AA Package P GPON indoor ONT with two POTS ports, four

Provisioning part number

3FE 46597 AA Package P GPON indoor ONT with two POTS ports, four

Description CLEI CPR ECI/

10/100/1000 Base-T Ethernet interfaces, and one 100 mW Wi-Fi radio with on/off switch.

This ONT features two USB 2.0 ports and supports SC/APC optics.

Includes two 5dBI indoor multi-directional external WiFi antenna (not detachable), one 1.5m CAT-5E Ethernet cable with RJ-45 endpoint, and one 1.5m RJ-11 cable.

Also includes one 2-pin wall-mounted 12V AC/DC power adapter with US plug.

10/100/1000 Base-T Ethernet interfaces, and one 200 mW Wi-Fi radio with on/off switch.