Nokia CR-99 - Cell Phone charger/holder User Manual

Nokia Universal Charging Holder
CR-99

9207241

5

6

7

ENGLISH

© 2007 Nokia. All rights reserved. Nokia and Nokia Connecting People are

registered trademarks of Nokia Corporation.

Introduction

With the Nokia Universal Charging
Holder CR-99, you can secure your
compatible mobile device in a car.

When you install the mobile holder,
ensure that it does not interfere with
or hinder the steering or braking
systems or other systems used in the
operation of the vehicle (for example,
airbags) or disturb your field of vision
while driving. Check that the
deployment of the airbags is not
blocked or impaired in any way.

Ensure that the holder is not installed
where you might come in contact
with it in the event of an accident or
collision.

Only operate the holder and the
mobile device placed in it if it is safe
to do so under all driving conditions.

Read this guide carefully before
installing the holder. Also, read the
user guide for the mounting device to
which you attach the holder. Keep all
accessories and enhancements out of
the reach of small children.

Attach to a mounting device

To attach the holder to the supplied
swivel mount or the Nokia Holder Easy
Mount HH-12, remove the protection

plate with the Nokia text from the
holder, attach the holder to the
mounting device with the supplied

ENGLISH

screw, and replace the protection
plate (see Figure 1 on the title page).

When you attach the holder, ensure
that the display of the mobile device is

Set up

You can use a compatible charger
with a mobile device that is placed in
the holder. For this purpose, the holder
is supplied with two nuts of different
sizes. If the arms of the holder cover
the side keys of your mobile device
when using the preinstalled nut, use
the other nut instead.

clearly visible for the user. For your
safety, install the holder in the upright
position.

Insert the charger cable into the slot
in the nut (3B). Push the nut into the
ring (3C). Attach the locking catch
(3D).

If the charger connector is not located
at the bottom of your mobile device,
remove the locking catch, and push

the nut through the ring (4A). Loop
Push the release buttons at the sides
of the holder to expand the arms to
the maximum width (2).

If the charger connector is located at
the bottom of your mobile device,
remove the locking catch by pulling it
from the holder, and push the nut
through the ring to detach it (3A).

the charger cable onto the nut (4B);

adjust the charger plug so that it

reaches to the charger connector on

your mobile device. Push the nut into

the ring (4C). Attach the locking catch

(4D).

Place or remove a device

ENGLISH

Do not place or remove a mobile
device while driving.

Place the device into the holder from
the top. If the charger connector is
located at the bottom of the device,
slide the ring or rotate the nut to align
the charger plug with the charger
connector (5). Gently push the device

Care and maintenance

Your device is a product of superior
design and craftsmanship and should be
treated with care. The following

downwards to insert the charger plug

in the upright position into the

charger connector, and press the arms

to lock the device firmly in place (6).

To remove the device, press the

release buttons, and pull the device

out (7).

• Do not use harsh chemicals, cleaning
solvents, or strong detergents to
clean the device.

suggestions will help you protect your
warranty coverage.

• Do not use or store the device in
dusty, dirty areas. Its moving parts
can be damaged.

• Do not drop, knock, or shake the
device. Rough handling can break fine
mechanics.

• Do not paint the device. Paint can
clog the moving parts and prevent
proper operation.

If the product is not working properly,
take it to the nearest authorized service
facility for service.

Soporte de cargador universal
Nokia CR-99

9207241

5

6

7