Page 1
Customer Care Solutions
Technical Documentation
4-Service Tools
Issue 1 11/2004 COMPANY CONFIDENTIAL 1
Copyright © 2004 Nokia. All Rights Reserved.
Page 2
CCS Technical Documentation
Contents
Service Tools................................................................................................................. 3
RM-12
2 COMPANY CONFIDENTIAL Issue 1 11/2004
Copyright © 2004 Nokia. All Rights Reserved.
Page 3
RM-12
CCS Technical Documentation
Service Tools
Product Service Tool Photo Description Info
ACF-8 Universal Power
Supply
ACP-8 Charger To be used with JBT-9.
AXP-8 Printer Cable The Parallel Printer Cable con-
AXS-4 D9-D9 Cable The AXS-4 D9-D9 service cable
ACF-8 is used to power FPS-8.
ACF-8 has 6 Vdc and 2.1A output.
nects the parallel connector of
the PC and the parallel input of
the FPS-8.
is used to connect two 9-pin
connectors (e.g., between PC
and FPS-8). AXS-4 length is
2meters.
CA-5S DC Cable The DC Cable CA-5S is used to
connect the docking station to
the charger connection (Vin) of
the phone to conduct the
charger calibration service procedure.
CA10DS
Issue 1 11/2004 COMPANY CONFIDENTIAL 3
Parallel cable
Copyright © 2004 Nokia. All Rights Reserved.
Page 4
CCS Technical Documentation
Product Service Tool Photo Description Info
RM-12
CA-
Cable for FLS-4S
28DS
CA33DS
DA-43 Docking station
adapter
Test pins for DA-
43 (10 pcs)
DA-43 is used with SA-63 RF
adapter.
Note! When attaching DA-43
with RM-12, be extra careful.
This is important in order to
avoid damaging the RF connector in RM-12.
See the end of this document
for more information.
DAU-9S MBUS Cable The MBUS cable DAU-9S has a
modular connector and is used
between PC serial port and, for
example, the MJ-32, or JBV-1..
DKU-2 U SB Cable Note! The cable cannot be used
as a straight-through USB connection cable.
4 COMPANY CONFIDENTIAL Issue 1 11/2004
Copyright © 2004 Nokia. All Rights Reserved.
Page 5
RM-12
CCS Technical Documentation
Product Service Tool Photo Description Info
FLA-46 POS flash
adapter
This accessory replaces the
phone battery and allows the
service SW to communicate
with the handset for flashing
Test pins for
FLA-46 (10 pcs)
and other POS functions using
the FLS-4S device setup.
The device can also be pow-
ered by an external P/S (3.9-4.5
VDC...DO NOT exceed
4.5.VDC). Pins (0770450) are
replaceable as long as they do
not get stuck inside the PIN
tower.
FLC-2 DC Cable FLC-2 is used to supply a con-
trolled operating voltage.
FLS-4S POS Flash
Adapter
The Point of Sale (POS) flash is
a low-cost software upgrade
tool (dongle and flash device
incorporated). This requires the
XCS-1 cable and ACP-8U for
operation.
FPS-8 Flash Prommer The Flash Prommer FPS-8 is
used for heavy flashing.
FPS-10 Flash Prommer
Issue 1 11/2004 COMPANY CONFIDENTIAL 5
Copyright © 2004 Nokia. All Rights Reserved.
Page 6
RM-12
CCS Technical Documentation
Product Service Tool Photo Description Info
JBT -9 Test & IF- b ox for
Bluetooth testing
JBV-1 Docking Station The Docking Station and the
Docking Station Adapter are
needed for Mbus, Fbus, RF,
and audio connections.
This setup allows connection
between flash prommers. When
the audio box is connected, it
has to be connected to the
phone’s audio connector. The
Docking Station can be pow-
ered by FPS-8 or external
power supply.
MJ-32 Module Jig
Test pins for MJ32 (10 pcs)
Fuse for MJ-32
(10 pcs)
Sp are flex unit for
MJ-32
MJS-76 LGA rework jig
Used for testing the following
modules: User Interface as well
as Baseband and RF on system
module.
Display can be On or Off during
the repair process.
Incl. flex opening tool SS-34.
Extra UI flex for module jig.
6 COMPANY CONFIDENTIAL Issue 1 11/2004
Copyright © 2004 Nokia. All Rights Reserved.
Page 7
RM-12
CCS Technical Documentation
Product Service Tool Photo Description Info
PCS-1 Power Cable The Power Cable PCS-1 is
used to connect the service
tools (JBV -1, MJS-57) to an
external power supply.
PKD-1 SW Security
Device
SW security device PKD-1 is
hardware device that, when
connected to the parallel (LPT)
port of the PC, enables the use
of the service software. Without
the dongle present, it is not pos-
sible to use the service soft-
ware. Printers or other
peripheral devices can be con-
nected to the PC through the
dongle, if needed.
Caution: Make sure that you
have switched off the PC and
the printer before making con-
nections!
Caution: Do not connect the
PKD-1 to the serial port. You
may damage your PKD-1!
RJ-24 Rework jig For rework of the FM radio chip
N6100.
RJ-37 Soldering jig
SA-63 RF adapter To be used with DA-43 and MJ-
32.
Note! Cable includes RF attenu-
ation values.
Issue 1 11/2004 COMPANY CONFIDENTIAL 7
Copyright © 2004 Nokia. All Rights Reserved.
Page 8
CCS Technical Documentation
Product Service Tool Photo Description Info
SES-3 LGA rework
stencil
RM-12
SF-12 S-RAM module
for FPS-8
SPS-1 Solder paste
spreader
SPS- 2 Solder paste
spreader
Extra memory for FPS-8.
For rework jig and stencil.
SRT-6 Camera removal/
insert tool
8 COMPANY CONFIDENTIAL Issue 1 11/2004
Copyright © 2004 Nokia. All Rights Reserved.
Page 9
RM-12
CCS Technical Documentation
Product Service Tool Photo Description Info
SS-34 Flex opening tool
For MJ-32 module jig.
ST-5 Rework stencil For rework of the FM radio chip
N6100.
SX-2 Smart card Smart card for FPS-10/11.
XCS-1 Service Cable The XCS-1 Service Cable is
used to connect FLS-4 to FLA-
46.
XCS-4 Service Cable XCS-4 is a shielded (one spe-
cially shielded conductor) serv-
ice cable for flashing and
service purposes.
Issue 1 11/2004 COMPANY CONFIDENTIAL 9
Copyright © 2004 Nokia. All Rights Reserved.
Page 10
RM-12
CCS Technical Documentation
Product Service Tool Photo Description Info
XRF-1 RF Cable RF cable XRF-1 is used to connect
e.g. MJ-32 and DA-43 to RF mea-
surement equipment.
N/A Standard USB
cable
Proper Attachment of RM-12 with DA-43
Instructions:
2
1 The device should be as much as possible pressed into the battery hooks.
2 Press the device down.
1
1
10 COMPANY CONFIDENTIAL Issue 1 11/2004
Copyright © 2004 Nokia. All Rights Reserved.
Page 11
Service Tool Reuse from Other Programs
Description Note
SK-5 Rework Kit for N6100 Contains RJ-24 and ST-5
ST-5 Rework Stencil for N6100 For radio chip.
Rework Jig for N7000 For power amplifier.
Rework Stencil for N7000
Loading...