Nokia 7577WPONHOU User Manual

Download

Page 1

HOU Product Guide

WPON solution

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT March 29, 2018

Nokia — Proprietary and confiden tial Use pursuan t to applicable agreements

DRAFT

Page 2

HOU Product Guide

Nokia is a registered trademark of Nok ia Corpor ation. Other pr oduct s and company names mentioned herein may be trademarks or tradenames of their respective owners.

The information presented is subject t o change without notice. No responsibility is assumed for inaccuracies contained herein.

not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 3

HOU Product Guide Preface

1 Preface

This preface provides general informa ti on a bout the documentation for the Home Outside Unit (HOU) of the Nokia WPON solution.

1.1 Scope

The documentation for the HOU provides information about saf ety, features and functionality, ordering, hardware install ation and maintenance, and software installation procedures for the HOU in the current release of the WPON solution.

1.2 Audience

The documentation for the HOU is intended for pla nners, admi nis trator s, operat ors , and maintenance personnel involved in inst alling, upgrading, or maintaining the HOU.

1.3 Required knowledge

The reader must be familiar with general telecommunications principles.

1.4 Acronym s and initialisms

The expansions and optional descriptions of most acronyms and initialisms appear in the glossary.

1.5 Assistance and ordering phone numbers

Nokia provides global technical support through regional call centers. Phone numbers for the regional call centers are available at the following URL: http://support.alcatel-lucent.com

For ordering information, contact your Nokia sales representative.

Issue: 01 DRAFT << doc part number tbd >> 3

DRAFT

Page 4

Preface

HOU Product Guide

1.6 Nokia quality processes

Nokia’s HOU quality practices are in compliance with TL 9000 requi rements.These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met. The customer or its representatives may be allowed to perform on-site quality surveillance audits, as agreed upon during contract negotiations

1.7 Safety information

For safety information, see the appropriate safety guidelines chapter.

1.8 Documents

Documents are available from Nokia using ALED or OLCS.

Procedure 1 To download a ZIP file package of the customer documentation

1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you

are a new user and require access to this service, please contact your Nokia sales representative.

2 From the Technical Content for drop-down menu, choose the product.

3 Click on Downloads: Electronic Delivery.

4 Choose Documentation from the drop-down menu and click Next.

5 Select the image from the drop-down menu and click Next.

6 Follow the on-screen directions to download the file.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 5

HOU Product Guide Preface

Procedure 2 To access individual documents

Individual PDFs of customer documents are also accessible through the Nokia Customer Support website.

1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you

are a new user and require access to this service, please contact your Nokia sales representative.

2 From the Technical Content for drop-down menu, choose the product.

3 Click on Manuals and Guides to display a list of customer documents by title and part

number. You can filter this list using the Release drop-down menu.

4 Click on the PDF to open or save the file.

1.9 Special information

The following are examples of how special inf ormation is presented in this document.

Danger — Danger indicates that the descri bed activity or

situation may result in serious personal injury or death; for example, high voltage or electric shock hazards.

Warning — Warning indicates that the described acti vity or

situation may, or will, cause equipment damage or serious performance problems.

Caution — Caution indicates that the described activi ty or

situation may, or will, cause service interruption.

Note — A note provides information that is, or may be, of

special interest.

Issue: 01 DRAFT << doc part number tbd >> 5

DRAFT

Page 6

Preface

1.9.1 Steps with options or substeps

When there are options in a step, they are identi fied by letters. When there are required substeps in a step, they are identified by roman numerals.

Procedure 3 Example of options in a step

At step 1, you must choose option a or b.

1 This step offers two options. You must choose one of the following:

a This is one option. b This is another option.

2 You must perform this step.

HOU Product Guide

Procedure 4 Example of required substeps in a step

At step 1, you must perform a series of substeps within the step.

1 This step has a series of substeps that you must perform to complete the step. You must

perform the following substeps:

i This is the first substep. ii This is the second substep. iii This is the third substep.

2 You must perform this step.

1.10 Multiple PDF document search

You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single displ ay panel. The results are grouped by PDF file, and you can expand the entry for each file.

Note — The PDF files in which you search must be in the same

folder.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 7

HOU Product Guide Preface

Procedure 5 To search multiple PDF files for a common term

1 Open Adobe Acrobat Reader.

2 Choose EditSearch from the Acrobat Reader main menu. The Search PDF panel appears.

3 Enter the search criteria.

4 Click on the All PDF Documents In radio button.

5 Select the folder in which to search using the drop-down menu.

6 Click on the Search button.

Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol.

Issue: 01 DRAFT << doc part number tbd >> 7

DRAFT

Page 8

Preface

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 9

HOU Product Guide HOU legal and data privacy information

2 HOU legal and data privacy

information

2.1 Purpose

2.2 Data privacy

2.1 Purpose

This chapter describes legal and data privacy information for the HOU. The information shall not be interpreted as a specification, modification, or

amendment to the specification, or additional or other warranty of any kind. In case of discrepancy between this document and product speci fi cation or terms and conditions of the valid supply agreement between Nokia and the customer, the supply agreement and product specificati on shall always prevail over thi s document.

2.2 Data privacy

2.2.1 Privacy rules

Nokia intends to serve our cus tomer s wit h innovat ive offeri ngs while complyi ng with privacy rules, and enable our customers to satisfy legal and social privacy requirements.

The development of products, sys tems, and soluti ons according to Nokia pr ocesses ensures the following:

• respect of end-user privacy

• compliance with privacy laws

• makes it simple and straightforward for Nokia customer s to buil d

privacy-respecting services

• offer enhanced protection against uni ntended use

Nokia strives to perform the following:

• provide products with design and features that enabl e its operator customers to

comply with their privacy obligations

• use reliable and trustworthy methods, that is, no security breaches

• ensure that Nokia products respect the privacy of end- users

Issue: 01 DRAFT << doc part number tbd >> 9

DRAFT

Page 10

HOU legal and data privacy information

2.2.2 Privacy impact assessment

A privacy impact assessment analyzes what subscri ber personal data the product supports and what is the effect of potential breaches.

Subscriber personal data is information r elating to an i dentified or ident ifiable natural person.

Some applications support the export and backup of application data. If the application data contains subscriber personal data, then this subscriber personal data is also exported.

Table 1 describes the data that the HOU col lects and stores, and the sa feguards that are in place to protect data privacy.

Note — The information in the table is applicable to the current

(first) release of the HOU.

<< the table is based on a template that TechComms is developing in consultation with Shawn Abigail; info in the table is taken from 3TG-00001-0007-DSZZA-01P05-Personal Data Inventory for WPON.xlsx; it should be noted that there are discrepancies between the template as used here and the spreadsheet that will need to be resolved, including a separate table for safeguards (the discrepancies are not indicated here, and will need to be approved by Shawn) >>

HOU Product Guide

<< it is not clear to me why there is a row for Serial number >>

Table 1 HOU data privacy strategy and safeguards

Data type Collected byPurpose

of data collection

HOU location (HOU GPS longitude, latitude and elevation information)

(1 of 2)

GPS Needed to

identify the location for HOU equipment

Stored by Retention

period

Stored in ConfD

Data is retained as long as the customer record is active. If there are system backups, data may be retained after a customer record is inactive.

Processed Access

No Only the

restricted by role

respective users and administrat ors have access

Anonymization support

Not anonymized Saved in

Safeguards

ConfD in Binary

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 11

HOU Product Guide HOU legal and data privacy information

Data type Collected byPurpose

of data collection

MAC address (subscriber's MAC address)

Serial number (equipment serial number)

Operator Used for

Not collected

black and white list in ACL

Hardware identificati on

Stored by Retention

period

Stored in ConfD

Saved in flash memory

Data is retained as long as the customer record is active. If there are system backups, data may be retained after a customer record is inactive.

Processed Access

restricted by role

Yes Only the

Not applicable

respective users and administrat ors have access

Not applicable

Anonymization support

Not anonymized Saved in

Not applicable It is not

Safeguards

ConfD in Binary

collected, and not used by application

(2 of 2)

Issue: 01 DRAFT << doc part number tbd >> 11

DRAFT

Page 12

HOU legal and data privacy information

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 13

HOU Product Guide

1 Preface.............................................................................................3

1.1 Scope ..........................................................................................................3

1.2 Audience......................................................................................................3

1.3 Required knowledge....................................................................................3

1.4 Acronyms and initialisms.............................................................................3

1.5 Assistance and ordering phone numbers....................................................3

1.6 Nokia quality processes...............................................................................4

1.7 Safety information........................................................................................4

1.8 Documents ..................................................................................................4

1.9 Special information......................................................................................5

1.9.1 Steps with options or substeps....................................................................6

1.10 Multiple PDF document search ...................................................................6

2 HOU legal and data p rivacy informa tion ............. ............... ..........9

2.1 Purpose.......................................................................................................9

2.2 Data privacy.................................................................................................9

2.2.1 Privacy rules................................................................................................9

2.2.2 Privacy impact assessment.......................................................................10

3 ETSI environmental and CRoHS guidelines...............................21

3.1 Environmental labels .................................................................................21

3.1.1 Overview....................................................................................................21

3.1.2 Environmental related labels.....................................................................21

3.1.2.1 Products below Maximum Concentration Value (MCV) label....................22

3.1.2.2 Products containing hazardous substances above Maximum

Concentration Value (MCV) label..............................................................22

3.2 Hazardous Substances Table (HST).........................................................23

3.3 Other environmental requirements............................................................24

3.3.1 HOU environmental requirements.............................................................24

3.3.2 Storage......................................................................................................24

3.3.3 Transportation ...........................................................................................24

3.3.4 Stationary use............................................................................................24

3.3.5 Thermal limitations ....................................................................................25

3.3.6 Material content compliance......................................................................25

3.3.7 End-of-life collection and treatment...........................................................25

4 ETSI safety g u id e li n e s................................ ............... ...................27

4.1 Safety instructions .....................................................................................27

4.1.1 Safety instruction boxes ............................................................................27

4.1.2 Safety-related labels..................................................................................28

4.2 Safety standards compliance ....................................................................29

4.2.1 EMC, EMI, and ESD compliance...............................................................29

4.2.2 Equipment safety standard compliance.....................................................29

4.2.3 Environmental standard compliance .........................................................30

4.2.4 Resistibility requirements compliance .......................................................30

4.2.5 Acoustic noise emission standard compliance..........................................30

4.3 Electrical safety guidelines........................................................................30

Issue: 01 DRAFT << doc part number tbd >> 13

DRAFT

Page 14

HOU Product Guide

4.3.1 Power supplies..........................................................................................30

4.3.2 Cabling ......................................................................................................31

4.3.3 Protective earth .........................................................................................31

4.4 ESD safety guidelines ...............................................................................31

4.5 Environmental requirements......................................................................31

5 ANSI safety guidelines .................................................................33

5.1 Safety instructions .....................................................................................33

5.1.1 Safety instruction boxes in customer documentation................................33

5.1.2 Safety-related labels..................................................................................34

5.2 Safety standards compliance ....................................................................36

5.2.1 EMC, EMI, and ESD standards compliance..............................................36

5.2.2 Equipment safety standard compliance.....................................................37

5.2.3 Environmental standards compliance........................................................37

5.2.4 Resistibility requirements compliance .......................................................37

5.3 Electrical safety guidelines........................................................................37

5.3.1 Power supplies..........................................................................................38

5.3.2 Cabling ......................................................................................................38

5.3.3 Protective earth .........................................................................................38

5.4 ESD safety guidelines ...............................................................................38

5.5 Environmental requirements......................................................................39

6 WPON solution overview .............................................................41

6.1 << something to consider >>.....................................................................41

6.2 WPON solution..........................................................................................41

6.2.1 APs and AP pairs ......................................................................................42

6.2.2 HOUs.........................................................................................................42

6.2.3 WPONs......................................................................................................43

6.2.4 More information about the WPON solution..............................................43

6.3 Compatible CPE........................................................................................43

7 HOU unit data s h ee t ................. ............................. ............... ........4 5

7.1 HOU part numbers and identification ........................................................45

7.2 HOU general description ...........................................................................46

7.3 HOU software and installation feature support..........................................47

7.4 Subscriber traffic interfaces on the HOU...................................................48

7.4.1 HOU physical connections and components.............................................48

7.4.2 HOU wireless components........................................................................49

7.5 HOU LED information................................................................................49

7.6 HOU specifications....................................................................................49

7.7 GEM ports and T-CONTs..........................................................................50

7.8 Performance monitoring statistics .............................................................51

7.9 Functional blocks.......................................................................................53

7.10 HOU standards compliance.......................................................................54

7.10.1 Energy-related products standby and off modes compliance....................54

7.10.2 HOU compliance statement.......................................................................55

7.10.3 Responsible party......................................................................................55

7.11 HOU special considerations......................................................................56

8 Pre-installation steps fo r a n HOU . .......................................... ....57

8.1 General......................................................................................................57

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 15

HOU Product Guide

8.2 Scan the HOU identifier.............................................................................57

8.3 Create and provision the HOU ..................................................................57

8.4 AP installation information.........................................................................58

8.5 << placeholder in case needed >>............................................................58

9 Procedures to install an HOU......................................................59

9.1 Purpose.....................................................................................................59

9.2 General......................................................................................................59

9.3 Prerequisites..............................................................................................59

9.4 Recommended tools..................................................................................60

9.5 Safety information......................................................................................60

9.6 Identify the mounting site...........................................................................62

9.7 Make preparations at the mounting site ....................................................62

9.8 Mount the HOU and make connections.....................................................63

9.9 Complete the installation...........................................................................63

10 Procedures to replace an HOU.................................... ................65

10.1 Purpose.....................................................................................................65

10.2 General......................................................................................................65

10.3 Prerequisites..............................................................................................65

10.4 Recommended tools..................................................................................65

10.5 Safety information......................................................................................65

10.6 HOU replacement procedure.....................................................................66

11 Configu re an H O U..... ................ ............... ............................. ........7 3

11.1 Remote configuration .................. ....... ...... ....... ...... ....... .............................73

11.2 Local configuration ....................................................................................73

12 Grounding safety ..........................................................................75

12.1 Ground safety information .........................................................................75

Issue: 01 DRAFT << doc part number tbd >> 15

DRAFT

Page 16

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 17

HOU Product Guide

List of figures

3 ETSI environmental and CRoHS guidelines...............................21

Figure 1 Products below MCV value label...............................................................22

Figure 2 Products above MCV value label ..............................................................23

Figure 3 Recycling/take back/disposal of product symbol.......................................26

4 ETSI safety g u id e li n e s................................ ............... ...................27

Figure 4 PSE certification ........................................................................................29

5 ANSI safety guidelines .................................................................33

Figure 5 Sample safety label on the HOU equipment .............................................35

6 WPON solution overview .............................................................41

Figure 6 High-level representation of the WPON solution.......................................41

Figure 7 Example of three WPONs connected to a PON that uses a P-OLT..........42

Figure 8 Example of an AP pair...............................................................................42

7 HOU unit data s h ee t ................. ............................. ............... ........4 5

Figure 9 HOU physical connections and components.............................................48

Figure 10 HOU LED location .....................................................................................49

Figure 11 Functional blocks of an HOU.....................................................................53

Figure 12 SOC functional block.................................................................................53

10 Procedures to replace an HOU.................................... ................65

Figure 13 G-241G-A ONT connections .................... ....... ...... ....... ...... ....... ...... ....... ...66

Figure 14 G-241G-A ONT mounted in an outdoor enclosure....................................68

Issue: 01 DRAFT << doc part number tbd >> 17

DRAFT

Page 18

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 19

HOU Product Guide

List of tables

2 HOU legal and data p rivacy informa tion ............. ............... ..........9

Table 1 HOU data privacy strategy and safeguards...............................................10

4 ETSI safety g u id e li n e s................................ ............... ...................27

Table 2 Safety labels..............................................................................................28

5 ANSI safety guidelines .................................................................33

Table 3 Safety labels..............................................................................................34

7 HOU unit data s h ee t ................. ............................. ............... ........4 5

Table 4 HOU part numbers and identification ........................................................46

Table 5 HOU accessories.......................................................................................46

Table 6 HOU subscriber traffic interfaces...............................................................48

Table 7 HOU physical connections and components.............................................48

Table 8 HOU LED behavior description .................................................................49

Table 9 HOU physical specifications......................................................................50

Table 10 HOU power consumption specifications....................................................50

Table 11 HOU environmental requirements.............................................................50

Table 12 G-241G-A ONT capacity for GEM ports and T-CONTs.............................51

Table 13 G-241G-A ONT ONTENET performance monitoring statistics..................51

Table 14 G-241G-A ONT ONTL2UNI performance monitoring statistics....... ....... ...52

Table 15 G-241G-A ONT PONONTTC, PONONTMCTC, PONONTTCHSI,

PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP

performance monitoring statistics..............................................................52

Table 16 G-241G-A ONT PONONTTC aggregate performance monitoring

statistics.....................................................................................................53

Table 17 Responsible party contact information ......................................................56

Table 18 G-241G-A ONT considerations and limitations ...................................... ...56

Issue: 01 DRAFT << doc part number tbd >> 19

DRAFT

Page 20

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 21

HOU Product Guide ETSI environmental and CRoHS guidelines

3 ETSI environmental and CRoHS

guidelines

This chapter provides i nformation about the ETSI env ironmental China Restri ction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line terminati on (OLT) and Ho me Outs ide Unit (HOU) equipment. This chapter also includes envir onme ntal operation parameters of general interest.

<< does this chapter need to include OLT info, or should it only cover the HOU? >>

<< this chapter needs to be closely looked at to make sure that it only provides applicable info for the HOU and that no relevant HOU info is missing, as it was copied from a similar chapter in the G-241G-A Product Guide >>

3.1 Environmental labels

This section describes the environmental instructions that are provided with the customer documentation, equipment, and location where the equipment resides.

3.1.1 Overview

CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold and imported in the territory of the mainland of the People’s Republic of China. EIP refers to products and their accessories manufactured by using electronic information technology, includi ng electronic communications products and such subcomponents as batteries and cables.

3.1.2 Environmental rel ated labels

Environmental labels are located on appropri ate equipment. The following are sample labels.

Issue: 01 DRAFT << doc part number tbd >> 21

DRAFT

Page 22

ETSI environmental and CRoHS guidelines

18986

3.1.2.1 Products below Maximum Concentration Value (MCV) label

Figure 1 shows the label that indicates a product is below the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). Products with this labe l are recyclable. The label may be found in this documentation or on the product.

Figure 1 Products below MCV value label

HOU Product Guide

3.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label

Figure 2 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). The number conta ined inside the label i ndicates the Environment-Friendly User Period (EFUP) value. The label may be found in this documentation or on the product.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 23

HOU Product Guide ETSI environmental and CRoHS guidelines

18985

Figure 2 Products above MCV value label

Together with major int ernational telecommuni cations equi pment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories. These values are based on manufacturers' extensive practical experience of the design, manufacturing, maintenance, usage conditions, operating environments, and physical condition of infrastructure and handsets after years of service. The values reflect minimum values and refer to products operated according to the intended use conditions. See “Hazardous Substances Table (HST)” for more information.

3.2 Hazardous Substances Table (HST)

This section describes the c ompliance of the OLT and HOU equipment to the CRoHS standard when the product and subassemblies contain haza rdous substances beyond the MCV value. This information is found in this user documentat ion where part numbers for the product and subassemblies are listed. It may be referenced in other OLT and HOU documentation.

In accordance with the People’s Republic of China Electronic Indu stry Standard Marking for the Control of Pollution Caused by Electronic Information Products (SJ/T11364-2006), customers may access th e Nokia Hazardous Substance Table, in Chinese, from the following location:

• http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRo

HS.pdf

Issue: 01 DRAFT << doc part number tbd >> 23

DRAFT

Page 24

ETSI environmental and CRoHS guidelines

3.3 Other environmental requiremen ts

Observe the following environmental requirements when handling the OLT or HOU equipment.

3.3.1 HOU environmental requirements

See chapter 7 in this product guide for more information about temperatu re rang es.

3.3.2 Storage

According to ETS 300-019-1-1 - Class 1.1, storage of HOU equipment must be in Class 1.1, weather-protected, temperature-controlled locations.

HOU Product Guide

<< is the above correct? >>

3.3.3 Transportation

According to EN 300-019-1-2 - Class 2.3, transportation of the HOU equipment must be in packed, public transportation with no rain on packing allowed.

<< is the above correct? >>

3.3.4 Stationa ry use

According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment must be in a temperature-controlled location, with no rain allowed, and with no condensation allowed.

<< is there an equivalent statement to the above for the HOU? >>

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 25

HOU Product Guide ETSI environmental and CRoHS guidelines

3.3.5 Thermal limitations

When the OLT is installed in the CO or CEV, install air filt ers on the OLT. The thermal limitations for OLT operation in a CO or CEV are:

• operating temperature: 5C to 40C (41F to 104F)

• short-term temperature: –5C to 50C (23F to 122F)

• operating relative humidity: 5% to 85%

• short-term relative humidity: 5% to 95%, but not to exceed 0.024 kg of water/kg

<< is there an equivalent to the above for the HOU? >>

3.3.6 Material content compliance

European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive a pplies to electr ical and electroni c products placed on the EU market after 1 July 2006, with various exemptions , including an exemption for lead solder in network infrastructure equipment. Nokia products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive.

Nokia has implemented a material/substance content management proces s. The process is described in: Nokia process for ensuring RoHS Compliance (1AA002660031ASZZA). This ensures compliance with the European Union Directive 2011/65/EU on the Restri ction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2). With the process equipment is assessed in accordance wit h the Harmonised Standard EN50581 :2012 (CENELEC) on Technical documentation for the assessment of electr ical and electronic products with respect to the restriction of hazardous substances.

3.3.7 End-of-life collection and treatment

Electronic products bearing or referencing the symbol shown in Figure 3, wh en put on the market within the European Union (EU), shall be collec ted and treat ed at the end of their useful life, in compliance wit h applicable EU and local legislation. They shall not be disposed of as part of unsorted municipa l waste. Due to materials that may be contained in the product, such as heavy metals or batteries, t he environment and human health may be negatively impacted as a result of inappr opriat e dispo sal.

Note — In the European Union, a solid bar under the symbol for

a crossed-out wheeled bin i ndicates that the product was put on the market after 13 August 2005.

Issue: 01 DRAFT << doc part number tbd >> 25

DRAFT

Page 26

ETSI environmental and CRoHS guidelines

Figure 3 Recycling/take back/disposal of product symbol

At the end of their life, the OLT and HOU are subject to the applicable local legislations that implement the European Dir ective 2012/19EU on waste electrical and electronic equipment (WEEE).

There can be different requirements fo r collection and treatment in different member states of the European Union.

HOU Product Guide

In compliance with legal requirements and contractual agreements, whe re applicable, Nokia will offer to provide for the collection and treatment of Nokia products bearing the logo shown in Figure 3 at the en d of their useful life, or product s displaced by Nokia equipment offers. For information regarding take-back of equipment by Nokia, or for more information regarding the requirements for recycling/disposal of product, contact your Nokia account manager or Nokia take back support at sustainability.global@nokia.com.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 27

HOU Product Guide ETSI safety guidelines

4 ETSI safety guidelines

This chapter provides information about the mandat ory regulations that govern the installation and operation of the Home Outside Units (HOUs) of the Nokia WPON solution in the ETSI market.

4.1 Safety instructions

This section describes the safety instructi ons that are provi ded in the HOU customer documentation and on the HOU equipment.

4.1.1 Safety instruction boxes

The safety instruction boxes are provided in the HOU customer documentation. Observe the instructions to meet safety requirements.

The following is an example of the Danger box.

Danger — Possibility of personal injury.

The Danger box indicates that the described activity or situation may pose a threat to personal safety. It call s a ttenti on to a situat ion or procedur e which, if not c orrect ly performed or adhered to, may result in death or seri ous physical harm.

Do not proceed beyond a Danger box until the indicated condit ions are fully understood and met.

The following is an example of the Warning box.

Warning 1 — Possibility of equipment damage. Warning 2 — Possibility of data loss.

The Warning box indicates that the described activ ity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-damaging situation or provides essential information to avoid the degradation of system operations or data.

Issue: 01 DRAFT << doc part number tbd >> 27

DRAFT

Page 28

ETSI safety guidelines

HOU Product Guide

Do not proceed beyond a warning until the indica ted condit ions are fully und erstood and met.

The following is an example of the Caution box.

Caution 1 — Possibility of service interruption. Caution 2 — Service interruption.

The Caution box indicates that th e describe d acti vity or si tuati on may, or will , cause service interruption.

Do not proceed beyond a caution until the indicated conditions are fully und erstood and met.

The following is an example of the Note box.

Note — Information of special interest.

The Note box provides information that assists the personnel working with HOU equipment. It does not provide safety-related instructions.

4.1.2 Safety-related labels

The HOU equipment is labeled with the specific safety ins tructions and compliance information that is rela ted to a product, or product variant, of the HOU equipment. Observe the instructions on the safety labels.

Table 2 provides sample safety labels on the HOU equipment.

Table 2 Safety labels

Description Label text

ESD warning Caution: This assembly contains an electrostatic sensitive device. PSE marking These power supplies are Japan PSE certified and compliant with

Figure 4 shows the PSE certification.

Japan VCCI emissions standards.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 29

HOU Product Guide ETSI safety guidelines

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

Warning

19841

Figure 4 PSE certification

4.2 Safety standards compliance

This section describes the HOU equipment compliance with the European safety standards.

4.2.1 EMC, EMI, and ESD compliance

The HOU equipment complies with the foll owing EMC, EMI, and ESD requ irements :

• EN 300-386 V1.5.1: Electromagnetic Compatibility and Radio Spectrum Matters

(ERM): Telecommunications Network Equipment; Electromagnet ic Compatibil ity (EMC) requirements; Electrostatic Discharge (ESD) requirements

• EN 55022 (2006): Class B, Information Technology Equipment, Radio

Disturbance Characteristics, limits and methods of measurement

• EN 55024 (2010): Information Technology Equipment , Immunity Charact eristic s,

limits and methods of measurement

• European Council Directive 2004/108/EC

• EN 300-386 V1.4.1: 2008

• EN 55022:2006 Class B

4.2.2 Equipment safety standard compliance

The HOU equipment complies with the requirements of EN 60950-1, Safety of Information Technology Equipment for use in a restricted location (per R-269).

Issue: 01 DRAFT << doc part number tbd >> 29

DRAFT

Page 30

ETSI safety guidelines

4.2.3 Environmental standard comp liance

4.2.4 Resistibility requirements compliance

4.2.5 Acoustic noise emission standard compliance

HOU Product Guide

The HOU equipment complies with the EN 300 019 European environmental standards.

The HOU equipment complies with the requirements of ITU Recommendation K.21 for resistibility of tele communication equipment installed in customer premises to over voltage and overcurrents.

<< does the above statement apply to the HOU? >>

The HOU equipment complies with EN 300 753 acoustic noise emission limit and test methods.

4.3 Electrical safety guidelines

This section provides the electrical safety guidelines for the HOU equipment.

Note 1 — The HOU equipment complies with the U.S. National

Electrical Code. However, local electrical authorities have jurisdiction when there are differences bet ween the local and U.S. standards.

Note 2 — The HOU equipment complies with BS EN 61140.

4.3.1 Power supplies

The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nok ia. Such use wil l void any warranty or support co ntract with Nokia. Such use greatly increases the danger of damage to equipment or property.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 31

HOU Product Guide ETSI safety guidelines

4.3.2 Cabling

The following are the guidelines regarding cables used for the HOU equipment:

• All cables must be approved by the relevant national electrical code.

• The cables for outdoor connection to the HOU equipment must be suitable for

outdoor use.

• POTS wiring run outside the subscriber premises must comply wit h the

requirements of local electrical codes. In some markets, the maximum allowed length of the outside run is 140 feet (43 m). If the outside run is longer, NEC requires primary protection at both the exit and entry points for the wire.

<< remove the last bullet since it refers to POTS? >>

4.3.3 Protective earth

Earthing and bonding of the HOU equipment must comply with the requirements of local electrical codes .

4.4 ESD safety guidelines

The HOU equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the HOU equipment.

Caution — This equipment is ESD sensitive. Proper ESD

protections should be u sed when you enter t he TELCO Access portion of HOU equipment.

During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD.

4.5 Envir onmental requireme nts

See section 7.6 in this guide for information about temper ature ranges.

Issue: 01 DRAFT << doc part number tbd >> 31

DRAFT

Page 32

ETSI safety guidelines

HOU Product Guide

During operation in the support ed temperatur e range, condens ation insi de the HOU equipment caused by humidity is not an issue. To avoid condensation caused by rapid changes in temperature and humidity, Nokia recommends:

• The door of the HOU equipment not be opened until temperature inside and

outside the equipment has stabilized.

• If the door of the HOU equipment must be opened after a rapid change in

temperature or humidity, use a dry cloth to wipe down the meta l interior to prevent the risk of condensation.

• When high humidity is present, installation of a cover or tent over the HOU

equipment helps prevent condensation when the door is opened.

<< does the HOU have a “door”? >>

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 33

HOU Product Guide ANSI safety guidelines

5 ANSI safety guidelines

This chapter provides information about the mandat ory regulations that govern the installation and operation of the Home Outside Units (HOUs) of the Nokia WPON solution in the North American or ANSI market.

5.1 Safety instructions

This section describes the safety instructi ons that are provi ded in the HOU customer documentation and on the HOU equipment.

5.1.1 Safety instruction boxes in customer documentation

The safety instruction boxes are provided in the HOU customer documentation. Observe the instructions to meet safety requirements.

The following is an example of the Danger box.

Danger — Possibility of personal injury.

Do not proceed beyond a Danger box until the indicated condit ions are fully understood and met.

The following is an example of the Warning box.

Warning 1 — Possibility of equipment damage. Warning 2 — Possibility of data loss.

Issue: 01 DRAFT << doc part number tbd >> 33

DRAFT

Page 34

ANSI safety guidelines

HOU Product Guide

Do not proceed beyond a warning until the indica ted condit ions are fully und erstood and met.

The following is an example of the Caution box.

Caution 1 — Possibility of service interruption. Caution 2 — Service interruption.

The Caution box indicates that th e describe d acti vity or si tuati on may, or will , cause service interruption.

Do not proceed beyond a caution until the indicated conditions are fully und erstood and met.

The following is an example of the Note box.

Note — Information of special interest.

The Note box provides information that assists the personnel working with HOU equipment. It does not provide safety-related instructions.

5.1.2 Safety-related labels

The HOU equipment is labeled with specific safety compliance i nformation and instructions that are relat ed to a variant of the HOU. Obser ve the ins tructions o n the safety labels.

Table 3 provides examples of the text in the various HOU equipment safety labels.

<< some of the examples in the table have “ONT” >>

Table 3 Safety labels

Description Label text

UL compliance Communication service equipment US listed. Type 3R enclosure -

TUV compliance Type 3R enclosure - Rainproof.

Rainproof.

(1 of 2)

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 35

HOU Product Guide ANSI safety guidelines

18533

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la class A est conforme a la norme NMB-003 du Canada

Tested to Comply with FCC Standards

FOR HOME OR OFFICE USE

COMMUNICATION SERVICE EQUIPMENT US LISTED 27FY Type 3R Enclosure - Rainproof

CAUTION

This Assembly Contains Electrostatic Sensitive Devices

Description Label text

ESD warning Caution: This assembly contains electrostatic sensitive device. Laser classification Class 1 laser product Laser product compliance This laser produc t conforms to all applicable standards of 21 CFR

FCC standards compliance Tested to comply with FCC standards for home or office use. CDRH compliance Complies with 21 CFR 1040.10 and 1040.11 except for deviations

Operation conditions This device complies with Part 15 of the FCC Rules. Operation is

Canadian standard compliance (modular ONT)

Canadian standard compliance (outdoor ONT)

CE marking There are various CE symbols for CE compliance.

(2 of 2)

1040.10 at date of manufacture.

pursuant to Laser Notice No. 50, dated June 24, 2007

subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES-003.

This Class B digital apparatus complies with Canadian ICES-003.

Figure 5 shows a sample safety label on the HOU equipment.

<< will need a new label, as the existing one shows “home or office use” >>

Figure 5 Sample safety label on the HOU equipment

Issue: 01 DRAFT << doc part number tbd >> 35

DRAFT

Page 36

ANSI safety guidelines

5.2 Safety standards compliance

5.2.1 EMC, EMI, and ESD standards compliance

HOU Product Guide

This section describes the HOU equipment compliance with North American safety standards.

Warning — Changes or modifications to this unit not expressly

approved by the party responsible for compli ance could void the user's authority to operate the equipment.

The HOU equipment complies with the following requirements:

<< reword first bullet? >>

• Federal Communications Commission (FCC) CFR 47, Part 15, Subpart B, Cla ss

A requirements for << HOU? >> equipment

• GR-1089-CORE requirements, including:

• Section 3 Electromagnetic Interference, Emissions Radiated and Conducted

• Section 3 Immunity, Radiated and Conducted

• Section 2 ESD Discharge Immunity: System Level Electrostatic Discharge and EFT

Immunity: Electrically Fast Transients

• ICES-003

• CAN/CSA C22.2 No. 60950-1

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This eq uipment generates, us es and can radiate radio frequenc y energy and, if not installed and us ed in accordance with t he instructions, may ca use harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turni ng the equipment of f and on, th e user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the recei ving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is needed.

• Consult the dealer or an experienced radio/TV technician for help.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 37

HOU Product Guide ANSI safety guidelines

5.2.2 Equipment safety standard compliance

The HOU equipment complies with the requirements of UL60950-1, Outdoor ONTs to “Communication Service Equipment” (CSE) and Indoor ONTs to Information Technology Equipment (ITE).

<< is “ONT” valid for both of these in the above statement? >>

5.2.3 Environmental standards c omplianc e

The HOU equipment complies with the following standards:

• GR-63-CORE (NEBS): requirements related to operating, storage, humidity,

altitude, earthquake, office vibration, transportation and handling, fire resistance and spread, airborne contaminants, illumination, and acoustic noise

• GR-487-CORE: requirements related to ra in, chemical, sand, and dust

• GR-487 R3-82: requirements related to condensation

• GR-3108: Requirements for Network Equipment in the Outside Plant (OSP)

• TP76200: Common Systems Equipment Interconnections Standards

5.2.4 Resistibility requirements compliance

The HOU equipment complies with the requirements of ITU Recommendation K.21 for resistibility of tele communication equipment installed in customer premises to overvoltage and overcurrents.

<< does the above statement apply to the HOU? >>

5.3 Electrical safety guidelines

This section provides the electrical safety guidelines for the HOU equipment.

Note — The HOU equipment complies with the U.S. National

Electrical Code. However, local electrical authorities have jurisdiction when there are differences bet ween the local and U.S. standards.

Issue: 01 DRAFT << doc part number tbd >> 37

DRAFT

Page 38

ANSI safety guidelines

5.3.1 Power supplies

5.3.2 Cabling

HOU Product Guide

The following are the guidelines regarding cables used for the HOU equipment:

• Use only cables approved by the relevant national electri cal code.

• Use cables suitable for outdoor use for connection to HOU equipment.

• The HOU equipment has been evaluated for use with external POTS wiring

without primary protection that may not exceed 140 ft (43 m) in reach. However, the power cable must not exceed 100 ft (31 m).

<< remove last bullet since it refers to POTS? >>

5.3.3 Protective earth

Earthing and bonding of the HOU equipment must comply with the requirements of NEC article 250 or local electrical codes.

5.4 ESD safety guidelines

The HOU equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the HOU equipment.

Caution — This equipment is ESD sensitive. Proper ESD

protections should be used when entering the TELCO Access portion of the HOU equipment.

During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD.

Nokia recommends that you prepare the site before you install the HOU equipment. In addition, you must control relative humidity, use static dissipating material for furniture or flooring, and restrict the use of air conditioning.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 39

HOU Product Guide ANSI safety guidelines

5.5 Envir onmental requireme nts

See section 7.6 in this guide for temperature ranges for HOU equipment. During operation in the support ed temperatur e range, condens ation insi de the HOU

equipment caused by humidity is not an issue. To avoid condensation caused by rapid changes in temperature and humidity, Nokia recommends:

• The door of the HOU equipment not be opened until temperature inside and

outside the enclosure has stabilized.

• If the door of the HOU equipment must be opened after a rapid change in

temperature or humidity, use a dry cloth to wipe down the meta l interior to prevent the risk of condensation.

• When high humidity is present, installation of a cover or tent over the HOU

equipment helps prevent condensation when the door is opened.

<< does the HOU have a door? >>

Issue: 01 DRAFT << doc part number tbd >> 39

DRAFT

Page 40

ANSI safety guidelines

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 41

HOU Product Guide WPON solution overview

6 WPON solution overview

6.2 WPON solution

6.3 Compatible CPE

6.1 << something to consider >>

<< A more detailed version of this chapter (12+ pages) is in the AP Product Guide.We need to determine if the stripped down version presented here should remain or if it should be replaced with one like the chapter in the AP Product Guide. It should be kept in mind that keeping two almost identical chapters in the two product guides is an invitation for them getting out of sync and as well the AP as an entity is more of a WPON big picture kind of item and the HOU as an entity is more of just a subscriber-type item that wirelessly connects to an AP. It seems to make sense to have the stripped version in the HOU Product Guide as presented here. >>

6.2 WPON solution

The Nokia Wireless PON solution provides a 60 GHz wireless drop for PON or P2P-based optic networks so that fiber optic cables are not used for connection to subscribers’ homes. The WPON has an Access Point (AP) that phys ica lly connec ts to the PON or P2P-based optic network. The AP uses 802.11ad for wireless communication with up to six Home Outside Units (HOUs) that provide Gigabit Ethernet connectivity to CPE inside subscribers homes.

<< do we need to provide more info about PONs and/or or P2P-based optic networks? What exactly is a “P2P-based optic network” - does it refer to GE, 2,5G, 10G Optical Ethernet? >> << there is quite a difference between a PON, which is a “point to multipoint” network, and a point to point network >> << can the PON be GPON, EPON, or other types of PONs? >>

By using 802.11ad, the WPON solution offers limited inte rference between sy stems because of narrow beams and inherent propagation limitati ons.

Figure 6 shows a high-level representation of the WPON solution providing a wireless drop from a PON or P2P-based optic network to three subscri ber homes.

Figure 6 High-level representation of the WPON solution

Issue: 01 DRAFT << doc part number tbd >> 41

DRAFT

Page 42

WPON solution overview

<< new figure to go here >> The WPON solution can be used with a fiber distribution network that incl udes the

Nokia 7342 ISAM FTTU P-OLT as shown in Figure 7.

Figure 7 Example of three WPONs connected to a PON that uses a P-OLT

new figure that has three WPONs instead of the nine ONTs that are

in the “fiber distribution network” figure typically used in the OLT and ONT documentation

6.2.1 APs and AP pairs

The AP provides the optical-to-wireless conversion for the WPON solution. The AP can be installed on a uti lity pole or on t he outside of a bui lding and uses 802.11ad for wireless line-of-sight communi cation with u p to si x HOUs up t o 300 m away << or is

it 100m? >>. An AP contains a GPS and magnetometer, enabling it to report its

location and orientation to the management system. See the AP Product Guide for detailed information about APs.

HOU Product Guide

<< check distance in above paragraph >>

Two APs can be installed as a pair on a utility pole to provide wider wireless coverage, such as to HOUs on houses on both sides of a street, In thi s case the two APs are known as an AP pair and they are connected to each other through a 2.5 Gigabit electrical Ethernet cable that ha ndles all t he traffic bet ween the two APs. An AP pair is considered to be a single AP, with one of APs of the pair serving as the Main AP and the other AP as the Extension AP.

Figure 8 shows an AP pair, with e ach AP of the AP pa ir using 8 02.11 ad for wi re les s line-of-sight communicati on with three HOUs.

Figure 8 Example of an AP pair

new figure to go here >>

6.2.2 HOUs

An HOU provides the wireless-to-Gigabit Ethernet electrical convers ion for the WPON solution at the subscriber premises. Based on 802.11ad, an HOU can be considered to be a wireless station (STA). An HOU is installed on the outside of a subscriber’s home and uses a Gigabit Ethernet elec trical cable for physical connectivity to CPE such as a residential gateway i nside the home. The same cable is used to provide power over Ethernet to the HOU. An HOU contains a GPS and magnetometer, enabling it to report its location and orientation to the management system.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 43

HOU Product Guide WPON solution overview

After physical installation and power up, an HOU automatically connect s to the best AP available, reports its presence, gets confi gured, and initiates service per the customer subscribed service type. Th e HOU also detects any neighbo ring APs in its line of sight and reports these to the management system.

See chapter 7 for detailed information about HOUs.

6.2.3 WPONs

A PON or a P2P-based optic network can have multiple WPONs; for example, the PON shown in Figure 7 has three WPONs.

At a minimum, a WPON consists of one AP and at least one HOU. A WPON has a single NNI point at the optical connection point of the AP with the

PON or P2P-based optic network. A WPON can have multiple UNI points, one at each HOU that is part of the WPON. An OLT in the PON sees each WPON as a NNI; the OLT does not see the UNIs. In

this respect, a WPON is seen in a simil ar way as a subtending node, such as a DPU. The number of APs and HOUs in a WPO N depends on the topology used for the

WPON. See the AP Product Guide for more information about WPON topologies.

6.2.4 More information about the WPON solution

See the AP Product Guide for more information about the WPON solu tion.

6.3 Compatible CPE

<< Include a table here, or in the CRN, that lists CPE that can connect to the HOU? If here, should it be in the AP product guide as well as in the HOU product guide? >>

The following table lists CPE that is compatible with the HOU.

<< need info to create table >>

Issue: 01 DRAFT << doc part number tbd >> 43

DRAFT

Page 44

WPON solution overview

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 45

HOU Product Guide HOU unit data sheet

7 HOU unit data sheet

7.1 HOU part numbers and identification

7.2 HOU general description

7.3 HOU software and installation feature support

7.4 Subscriber traffic interfaces on the HOU

7.5 HOU LED information

7.6 HOU specifications

7.7 GEM ports and T-CONTs

7.8 Performance monitoring statistics

7.9 Functional blocks

7.10 HOU standards compliance

7.11 HOU special considerations

7.1 HOU part numbers and identification

Table 4 provides part numbers and identification information for the HOU.

Issue: 01 DRAFT << doc part number tbd >> 45

DRAFT

Page 46

HOU unit data sheet

Table 4 HOU part numbers and identification

HOU Product Guide

Part number Provisioning

3FE 47290 AA

confirm >>

number

need >> HOU with one 802.11ad baseband unit and one Gigabit

Table 5 provides accessory or dering information for HOUs.

<< are there any orderable accessories for the HOUs? what about the Cat5 cable and wall-mounting hardware? >>

Table 5 HOU accessories

Accessory Orderable part number Notes

need >> << need >> << need >> need >> << need >> << need >>

Description CLEI CPR ECI/

Ethernet port.

<< need >> <<

The 802.11ad baseband unit is used for wireless connection to an AP.

The Gigabit Ethernet port is used for connection to CPE, such as a residential gateway, through a Cat5 cable. The HOU is POE-powered through the Cat 5 cable.

need

Bar code

need

<< is anything included, such as the Cat5 cable and mounting hardware? since we don’t know the length of cabling needed between the HO and CPE, is it even possible to provide a cable >>

7.2 HOU ge neral description

An HOU provides the wireless-to-Gigabit Ethernet electrical convers ion for the WPON solution at the subscriber premises. The HOU is i nstalled on the outside of a subscriber’s home and uses a Gigabit Ethernet elec trical cable for physical connectivity to CPE such as a r esidenti al gateway i nside the home. See sect i on 6.2 in this guide for more information about the WPON solution.

On the wireless side, the HOU is compliant with 802.11ad support ing unlicensed 60 GHz mmW ave wireless line-of-sight communication with 1 Gb/s peak speeds.

On the subscriber side, the HOU is compliant with <<need info >>

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 47

HOU Product Guide HOU unit data sheet

The HOU is managed through the WPON manager and the Nokia Altiplano cloud-native access platform. A loca l craft terminal access point is provided on the HOU through a Bluetooth interface (classical Bluetooth, reach greater than 20 m). See the AP Product Guide for more information about management of the WPON solution.

The HOU provides the following functions and features:

• wireless-to-Gigabit Ethernet conversion

• up to 3 Gbps aggregate capacity, support ing 1 Gbps peak s peeds to an AP up t o

100 m << or is it 300 m >> away << confirm aggregate vs peak values >>

• automatically connects to the best AP availabl e, reports its presence, gets

configured, and initiates service per the customer subscribed service type

• detects any neighboring APs in its line of sight and reports these to the

management system

• beam-forming antennas for fast and reliable wireless connection

• wide field of view for antennas (180 degrees horizontal and 60 degrees vertical)

means there is no need to aim the antenna

• installed on the outside of a subscriber’s hom e

• provides symmetrical Ether net connectivity at Gigabit speeds t o CPE over a Cat5

cable

• POE-powered over the Cat5 cable that connects to the CPE

• sends dying gasp signal upstream if loss of power occurs

• has a built-in GPS and magnetometer

• robust design for harsh conditions (IP66)

• small size (12 cm by 12 cm by 4 cm) means that it is barely noticeable on buildi ng

• MDI/MDIX auto sensing << confirm the HOU has this for its Ethernet

connection to the CPE

• network demarcation for all services << confirm if the AP or HOU does this

• interworking functions between the GEM and Ethernet layers << confirm the

HOU does this

• mux and demux functions to the PON or P2P optic al network<< confirm the AP,

not the HOU does this

• G984.4 standard and revised compliant OMCI interface for management and

provisioning <<

confirm the HOU has this >>

• on/off button << confirm the HOU has this >>

• support for AIS with DOWN MEP << confirm the HOU has this >>

7.3 HOU software and i nstallation feature s upport

Software for the HOU is managed through the WPON manager and the Nokia Altiplano; see the AP Product Guide for information about the WPON manager and Nokia Altiplano.

Issue: 01 DRAFT << doc part number tbd >> 47

DRAFT

Page 48

HOU unit data sheet

7.4 Subscriber traffic interfaces on the HOU

HOU Product Guide

For information about installing or repl acing an HOU, see the following chapters:

• chapter 8 (Pre-installation steps for an HOU)

• chapter 9 (Procedures to install an HOU)

• chapter 10 (Procedures to replace an HOU)

Table 6 describes the supported subscriber traffic interfaces for the HOU.

Table 6 HOU subscriber traffic interfaces

Wireless Ethernet

One for communication with an AP One Gigabit Ethernet for connection to CPE; the same connection is

used for power over Ethernet

7.4.1 HOU physical connections and components

Figure 9 shows the HOU physical connections and components and section 7.4.2 describes the wireless components.

Figure 9 HOU physical connections and components

add figure that has HOU connections and components (if no

components, then change title of section and figure)

Table 7 describes the HOU physical connections and components.

Table 7 HOU physical connections and components

Connectio n or component

Ethernet connection

Ground connection

On/off button This button turns the HOU on or off << Reset button This button turns resets the HOU <<

Description

This connection is provided through an RJ 25 connector. It is used for used for connecting to CPE, such as a residential gateway, through a Cat5 cable. POE power is provided through the same cable.

is there a ground point? >>

narrow hole?

is there an on/off button? >>

is there a reset; if yes is it a button with a

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 49

HOU Product Guide HOU unit data sheet

7.4.2 HOU wireless components

The HOU has one 802.11ad base band unit for wireless communication with an AP:

• the 802.11ad baseband unit has three si ngle-tile 32-ant enna/RF arrays t hat have

a scan range of +/- 90° Azimuth, +30°+x /-30°+x elevati on, antenna tiles tilted upwards, angle x <<

need values for “x” >>

• the 32-antenna/RF arrays use vertical polarization and are located at the center

line of the HOU

7.5 HOU LED information

The HOU has a single multifunction LED that is software-defined to light under certain conditions.

Figure 10 shows the location of the LED.

Figure 10 HOU LED location

add figure showing location of the LED>>

<< Table 8 describes the HOU LED. <<

Table 8 HOU LED behavior description

LED color and behavior

Off << Solid green << Solid red << Flashing green (fast) << Flashing green (slow) << Flashing red (fast) << Flashing red (slow) <<

any other (eg

alternating red and green)?

LED behavior description

need >> need >> need >> need >> need >> need >> need >> need >>

7.6 HOU specifications

need info for HOU LED >>

Table 9 lists the physical specifications for the HOU.

Issue: 01 DRAFT << doc part number tbd >> 49

DRAFT

Page 50

HOU unit data sheet

Table 9 HOU physical specifications

Dimensions Specifications

Height << Width << Depth << Weight [within  0.5 lb (0.23 kg)] <<

need >> need >> need >> need >>

Table 10 lists power consumption specifications for the HOU.

Table 10 HOU power consumption specifications

HOU Product Guide

Maximum power (not to exceed)

need >> << need >> << need >> << need >>

Condition Minimum

power

Table 11 lists the environmental requirements for the HOU.<<

Table 11 HOU environmental requirements

Mounting method

On an outside wall

Temperature range and humidity Altitude

Operating: 23F to 122F (-5C to 50C) ambient temperature 5% to 85% relative humidity, non-condensing

Storage: –40F to 140F (–40 to 60C) 5% to 93% relative humidity, non-condensing

7.7 GEM ports and T-CONTs

Condition

need to verify >>

Maximum operating altitude is 10 000 ft (3048 m) above mean sea level

Maximum non-operating altitude is 40 000 ft (12 192 m) above mean sea level

<< this section is as per the G-241G-A ONT product guide - does any of

it apply to the HOU?

Table 12 lists the maximum number of supported T-CONTs and GEM ports for G-241G-A ONT. Not all ONTs will be supported in all of the releases indicated the table. See the appropriate release Customer Release Notes for the most accurate list of supported devices.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 51

HOU Product Guide HOU unit data sheet

Table 12 G-241G-A ONT capacity for GEM ports and T-CONTs

ONT or MDU Maximum Notes Package P ONTs

GEM ports per ONT 124 124 are present; 122 are available, and 2 are reserved for multicast

T-CONTs per ONT 32 32 are present; 31 are available, and 1 is reserved for OMCI

and debugging

7.8 Performance monito ring statistics

<< this section is as per the G-241G-A ONT product guide - does any of

it apply to the HOU?

The following section identifies the supported performance monitoring statistics for G-241G-A ONT. A check mark indicates the statistic is supported on that ONT. An empty cell indicates the statistic is not supported. The following tables are categorized by supported alarm types:

• Table 13 provides statistics for ONTENET type counters

• Table 14 provides statistics for ONTL2UNI type counters

• Table 15 provides statistics for PONONTTC, PONONTMCTC, PONONTTCHSI,

PONONTTCCES, PONONTTCFLOW, and PONONTTCVOIP type counters

• Table 16 provides statistics for PONONTTC aggregate type counters

Note — If you have trouble accessing G-241G-A ONT

performance monitoring statistics using TL1, please contact your Nokia support representative for more information about how to access and retrieve performance monitoring type counters.

Table 13 G-241G-A ONT ONTENET performance monitoring statistics

ONT ONTENET statistics

FCSE

GPON

G-241G-A

Note

(1)

A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds

✓✓✓✓✓✓✓✓✓✓✓✓✓✓

RBO

SCF

MCF

IMTE

CSE

FTL

TBO

IMRE

SQE

Issue: 01 DRAFT << doc part number tbd >> 51

DRAFT

Page 52

HOU unit data sheet

HOU Product Guide

Table 14 G-241G-A ONT ONTL2UNI performance monitoring statistics

ONT ONTL2UNI statistics

BYTES

FRAMES

GPON

(1)

G-241G-A

Note

(1)

A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds

✓✓✓✓✓✓✓✓✓✓✓

MCFRAMES

DSDRPDFRMS

USDRPDFRMS

USFRAMES

USBYTES

DSFRAMES

DSBYTES

USMCFRAMES

DSMCFRAMES

Table 15 G-241G-A ONT PONONTTC, PONONTMCTC, PONONTTCHSI,

PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics

ONT PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES,

GPON

G-241G-A

Note

(1)

A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds

PONONTTCFLOW, PONONTTCVOIP statistics

TXBLOCKS

✓✓✓✓✓

TXFRAGS

RXBLOCKS

RXFRAGS

LOSTFRAGS

BADGEMHDRS

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 53

HOU Product Guide HOU unit data sheet

Table 16 G-241G-A ONT PONONTTC aggregate performance monitoring

statistics

ONT PONONTTC (aggregate) statistics

GPON

G-241G-A

Note

(1)

A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds

7.9 Functional blocks

Figure 11 shows the functional blocks for the HOU.

Figure 11 Functional blocks of an HOU

add figure showing the functional blocks of an HOU >>

<< Figure 12 shows the SoC functional block in more detail.

Figure 12 SOC functional block

TXBLOCKS

✓✓✓✓✓

TXFRAGS

RXBLOCKS

RXFRAGS

LOSTFRAGS

BADGEMHDRS

add figure showing the SoC functional block >>

<< The SoC for the HOU consists of the following key elements:

• Ethernet MAC:

The SoC provides up to four GE MACs. <<

confirm >>

• Control Processor:

The Control Processor features an integra l memory man agement unit that supports a dedicated 64 kbyte instructi on cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 400 MHz.

Issue: 01 DRAFT << doc part number tbd >> 53

DRAFT

Page 54

HOU unit data sheet

7.10 HOU standards compliance

HOU Product Guide

•

Switch matrix: The Switch matrix provides an integrated data channel between the f our GE

MACs, the GPON MAC, the control processor, and the oth er integrated elements such as flash memory, DRAM, and the local bus controller.

The HOUcompliant with the f ollowing standards: < < the following list is from the

G-241G-A ONT product guide - it needs to be reviewed carefully to make sure that it is complete and accurate with respect to the HOU

• EN-300019-2-1 (Class T1.2)

• EN-300019-2-2 (Class T2.3)

• EN-300019-2-3 (Class T3.2))

• ETL

• FCC (Class B)/CAN ICES-003

• IEEE 802.1p (QoS)

• IEEE 802.1q (VLANs)

• IEEE 802.3ab, 3i 3u (GE)

• IEEE 802.3 (2012) (auto-negotiation)

• IEEE 802.3x (flow control)

• MEF 2.0

• ITU-T G.984 (GPON interface framing)

• ITU-T G.984.2 (1.25 Gb/s, 2.5 Gb/s)

• ITU-T G.984.3 (activation with automatic discovery of a serial number and a

password)

• ITU-T G.984.4 (standard and revised) (OMCI interface for ONT management and

provisioning)

7.10.1 Energy-related products standby and off modes compliance

<< this section needs to be confirmed >> Hereby, Nokia declares that the HOU is in compliance with the essenti al

requirements and other relevant provisions of Directive 2009/125/EC together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013.

The HOU qualifies as equipment with high network availabi lity (HiNA) functionality. Since the main purpose of the HOU is to provide network functionality with HiNA 7 days /24 hours, the modes Off/Standby, Power Management, and Networked Standby are inappropriate.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 55

HOU Product Guide HOU unit data sheet

For information about the type and number of network ports, see “Subscriber traffic

interfaces on the HOU” in this chapter.

For information about power consumption, see “HOU specifications” in this chapter.

7.10.2 HOU compliance st atement

<< this section needs to be confirmed >> This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: 1 This device may not cause harmful interference.

2 This device must accept any interference received, including interference that

may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance c ould void the us er' s author ity t o opera te the equi pment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection agai nst harmful interference in a residential installati on. This equipment generates, uses and can radiate radio frequency energy and, if not install ed and used in accor dance with the instructions, may cause harmful interference to radio communications.

• Reorient or relocate the recei ving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is needed.

• Consult the dealer or an experienced radio/TV technician for help.

7.10.3 Responsible party

<< this section needs to be confirmed >>

<< if it is Raleigh, is the phone number and other info correct? >>

Table 17 lists the party in the US responsible for the HOU.

Issue: 01 DRAFT << doc part number tbd >> 55

DRAFT

Page 56

HOU unit data sheet

7.11 HOU special consid erations

HOU Product Guide

Table 17 Responsible party contact information

Legal Company name Nokia USA Inc. Address 2301 SUGAR BUSH RD. STE 300, RALEIGH,NC 27612 Phone, Fax +1 919 850 6127

<< are there any special considerations and limitations for the HOU? >>

the following table is for reference, as it is from the G-241G-A ONT

product guide

Table 18 G-241G-A ONT considerations and limitations

Considerations and limitations

Call History Data collection (ONTCALLHST) is supported, except for the following parameters: RTP packets (discarded), far-end RTCP and RTCP-XR participation, RTCP average and peak round trip delay, MOS, average jitter, number of jitter-buffer over-runs and under runs.

Some voice features are configurable on a per ONT basis, including Call Waiting, Call Hold, 3-Way Calling, and Call Transfer.

The following voice features / GSIP parameters are configurable on a per-Client/ per-ONT basis (not per-Subscriber):

• Enable Caller ID and Enable Caller Name ID

• Digitmap and the associated Interdigit and Critical timers and Enter key parameters

• Warmline timer is enabled per subscriber, but the warmline timer value is configured per ONT and must have

a lower value than the Permanent time

• Miscellaneous timers: Permanent, Timed-release, Reanswer, Error-tone, and CW-alert timers

• Features / functions: Message waiting mode, WMWI refresh interval, DTMF volume level

• Service Codes for the following features: CCW, Call Hold and Warmline

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 57

HOU Product Guide Pre-installation steps for an HOU

8 Pre-installation steps for an HOU

8.1 General

8.2 Scan the HOU identifier

8.3 Create and provision the HOU

8.4 AP installation information

8.5 << placeholder in case needed >>

8.1 General

<< the purpose of this chapter is to cover installation-related items that should be addressed at the CO or before the installer goes out to the installation site >>

<< briefly describe the various installation scenarios (such as installing

first AP (or a pair of APs) and one or more HOUs, adding an HOU to an existing WPON provided by an AP, adding a Relay AP (and one or more HOUs) to an existing WPON provided by an AP), and adding a second AP (and one or more HOUs) to create an AP pair? Is it likely that an AP would be installed by itself without at least one HOU being installed at the same time? It certainly seems possible that just a single HOU could be installed by itself for a "late uptake" customer. This could perhaps be covered at a general level in the WPON Overview chapter, with any specific info about the AP here, with a reference to the WPON Overview chapter.

8.2 Scan the HOU identifier

<< Scan the HOU identifier, as the WPON (Wireless PON) wiki of Feb

06/18 indicates to do this before installing the HOU (this reports the serial number of the <<xx>> to the WPON manager) on how to do this

>> << need details

8.3 Create and provision the HOU

<< Create and provision the HOU, through the WPON manager, as the

WPON (Wireless PON) wiki of Feb 06/18 indicates to do this before installing the HOU

>> << need details on how to do this >>

Issue: 01 DRAFT << doc part number tbd >> 57

DRAFT

Page 58

Pre-installation steps for an HOU

8.4 AP installation information

If you will be installing any APs while you are installing the HOU, refer to the AP Product Guide for information about APs, includi ng pre-installation steps and

procedures on installing APs.

8.5 << placeholder in case needed >>

<< if needed, for any other pre-installation activities >>

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 59

HOU Product Guide Procedures to install an HOU

9 Procedures to install an HOU

9.1 Purpose

9.2 General

9.3 Prerequisites

9.4 Recommended tools

9.5 Safety information

9.6 Identify the mounting site

9.7 Make preparations at the mounting site

9.8 Mount the HOU and make connections

9.9 Complete the installation

9.1 Purpose

This chapter provides the procedures to install an HOU.

9.2 General

<< need to determine what should go here or if this section is even

needed

9.3 Prerequisites

You need the following items before beginning the installation:

• HOU

• Cat5 Ethernet cabling and the following connectors: << confirm >>

• RJ-45 connector for connecting the cable to the HOU

• connector suitable for connecting the cable to the CPE

• wall-mounting brackets and fasteners for the HOU << confirm >>

• silicon or other waterproof sealing/caulking compound < < confirm >>

• mobile phone or tablet for local management of the HOU via Bluetooth

• << anything else? >>

Issue: 01 DRAFT << doc part number tbd >> 59

DRAFT

Page 60

Procedures to install an HOU

9.4 Recommended tools

You need the following tools for the installation:

• scanner for reading bar code on the HOU

• wire cutters and tools for attaching connectors to the Cat5 cabling

• something << what? >> for measuring distance << others?>> << note that

the rest of the items in the list are from the G-241G-A ONT Product Guide and might not apply to an HOU installation

• #2 Phillips screwdriver

• 1/4 in. (6 mm) flat bl ade screwdriver

• wire strippers

• RJ-45 cable plug crimp tool

• voltmeter or multimeter

• drill and drill bits

• pin-in-hex screwdriver

HOU Product Guide

9.5 Safety information

Read the following safety information before beginning the installation

need to confirm that the info in this section applies to the HOU, as it

is from the G-241G-A Product Guide

include height/fall safety info (or is it not needed for HOU)?

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 61

HOU Product Guide Procedures to install an HOU

- do we need to add a reference to chapter 11 for grounding safety? >>

Danger 1 — Hazardous electrical voltages and cur rent s can

cause serious physical harm or death. Always use insulated tools and follow prop er safety precautions when connecting or disconnecting power circuits.

Danger 2 — Make sure all sources of power a re turned off and

have no live voltages present on feed lines or termina ls. Use a voltmeter to measure for voltage before proceedi ng.

Danger 3 — Always contact the local utility company befor e

connecting the enclosure to the utilities.

Warning 1 — This equipment is ESD sensitive. Proper ESD

protections should be used when removing the fiber access cover of the HOU.

<< does the HOU have an access cover? >>

Warning 2 — The intra-building port(s) of the equipment or

subassembly is suitable for connecti on to intra-building or unexposed wiring or cabling only. The intra-building port(s) of the equipment or subassembly MUST NOT be metallically connected to interfaces that connect to the OSP or its wiring. These interfaces are designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in GR-

1089) and require isol ation from the exposed OSP ca bling. The addition of Primary Protectors is not suff icient protection in order to connect these interfaces metallically to OSP wiring.

Note 1 — Observe the local and national laws and regulations

that may be applicable to this install ation.

Note 2 — The HOU should be installed in accordance with the

applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC.

Note 3 — The HOU must be installed by qualified service

personnel.

Note 4 — See HOU specifications in chapter 7 for the

temperature ranges for the HOU.

Issue: 01 DRAFT << doc part number tbd >> 61

DRAFT

Page 62

Procedures to install an HOU

9.6 Identify the mounting site

<<intro needed >>

1 Identify the exact location for the HOU on an outside wall of the house; confi rming that there

is line of sight and there is less than 100 m (or is it 300 m?) between the prospective HOU location and planned or installed AP(s) (lines of sight will depend on the installation scenario, covered in section 8.1) << need details >> If possible, find a location below a window that can easily be accessed and worked on from within the house.

2 Confirm that the prospective HOU location is acceptable within the house, and that Cat5

cabling can be run inside the house from the CPE or prospective CPE location to the prospective HOU location.

3 STOP. This procedure is complete.

9.7 Make preparation s at the mounting site

HOU Product Guide

<< intro needed >>

1 Confirm that the CPE that the HOU is going to connect to is installed and powered up, or

install and power up the CPE <<

2 Connect the Cat5 cabling to the CPE (may need to attach a connector to the cabling first) and

route the cable to the installation location for the HOU. The Cat5 cable must be routed inside the house to a point inside the house from the installation location and must have enough length to be able to pass through the wall to reach the HOU once it is mounted on the outside of the wall.

need details >>

3 << is there a ground point on the HOU? If yes, then this step should be about

making sure the far-end of the ground cable is attached to ground, presumably outside, and routing the ground cable to the installation location for the HOU - will need details >>

4 Scan the HOU if it was not done in section 8.2 (assuming that it is not too late if it was not

already scanned)? <<

5 Do any pre-work on the HOU and/or wall before mounting the HOU on the wall, esp since

that actually mounting of the HOU could be high up and so it would be good to do what can be done while on the ground (such as attaching a mounting plate to the HOU) or before mounting the HOU (such as attaching a bracket to the wall) in order to minimize how many times the installer needs to go up the pole or on a ladder. <<

need details >>

6 STOP. This procedure is complete.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 63

HOU Product Guide Procedures to install an HOU

9.8 Mount the HOU and make connections

<< need intro >> << Perhaps chapters 18 and 19 of the 7368 ISAM ONT Hardware

and Cabling guide might have useful info

1 Drill a << what diameter? >> hole through the wall at the HOU location and thread the Cat5

cable through the hole (may need to attach connector to the cabling after threading) <<

details

2 Connect ground to the HOU << need details >> << perhaps use info from chapter 6 in the

7368 ISAM ONT Hardware and Cabling guide >> << may need to trim to an appropriate length first >>

3 Connect the protruding end of the Cat5 cable to the HOU (may need to attach connector to

the cabling) <<

4 Mount the HOU (with attached ground and Cat5 cables) on the wall << need details >> <<

what about sealing around the HOU with silicon caulking etc and sealing the hole on the inside? >>

need details >> << may need to trim to an appropriate length first >>

need

5 STOP. This procedure is complete.

9.9 Complete the installation

<< need intro >>

1 Power up the HOU by using the ON/OFF power switch. << add a figure showing

location of switch?

2 Verify the HOU LED and voltage status << need details >> << are there applicable details

in the 7368 Hardware and Cabling Installation Guide that could be added here? >>

3 Verify system functionality of the HOU << assume that this can be done via Bluetooth (used

with external app of mobile phone or tablet for local device management) >> <<

details

4 If the AP or APs for the HOU have been installed, check that the HOU has wireless

connectivity with the AP and APs <<

>> << configure anything on the HOU via Bluetooth >>

need details >>

need

Issue: 01 DRAFT << doc part number tbd >> 63

DRAFT

Page 64

Procedures to install an HOU

5 If necessary, reset the HOU. << can the HOU be reset as described here? >>

i Locate the Reset button. ii Insert the end of a straightened paper clip or other narrow object into the hole in the

6 STOP. This procedure is complete.

HOU Product Guide

Reset button to reset the HOU.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 65

HOU Product Guide Procedures to replace an HOU

10 Procedures to replace an HOU

10.1 Purpose

10.2 General

10.3 Prerequisites

10.4 Recommended tools

10.5 Safety information

10.6 HOU replacement procedure

10.1 Purpose

This chapter provides t he procedures to replac e an HOU. << work on this chapter

after working on the installation chapter

10.2 General

<< is this section needed? >>

10.3 Prerequisites

<< work on this section after working on the installation chapter >>

10.4 Recommended tools

<< work on this chapter after working on the installation chapter >>

10.5 Safety information

<< work on this chapter after working on the installation chapter >>

Issue: 01 DRAFT << doc part number tbd >> 65

DRAFT

Page 66

Procedures to replace an HOU

10.6 HOU replacement procedure

<< work on HOU replacement procedures after working on the HOU installation

chapter and is left here for use as a model for the HOU

1 Deactivate the ONT services at the P-OLT.

If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS).

i Use the RTRV-ONT command to verify the ONT status and the associated services.

ii If the ONT is in service, place the ONT in OOS state.

HOU Product Guide

>> << this procedure is currently the one for replacing the G-241G-A ONT

Record the serial number or the SLID of the ONT displayed in the command output. Example:

RTRV-ONT::ONT-1-1-1-1-1;

Example:

ED-ONT::ONT-1-1-1-1-1;

2 Power down the ONT unit by using the ON/OFF power switch.

3 Disconnect the video, POTS, Ethernet, power, and ground cables from the ONT; see Figure

13.

Figure 13 G-241G-A ONT connections

POTS 1Video POTS 2

RF VideoGround lug

4 Unplug the SC/APC fiber optic cable from the ONT.

i Loosen the lock screw on the fiber optic connection clip. ii Lift the connection clip up. iii Unplug the fiber optic cable with SC/APC adapter from the fiber optic connector; see

POTS ports

(RJ-14)

Figure 13.

DATA 1 DATA 2 DATA 3 DATA 4

Gigabit Ethernet

ports (RJ-45)

ON/OFF

On/off button

POWER

Power

connector

SC/APC

connector

28061

iv Lower the clip and tighten the lock screw.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 67

HOU Product Guide Procedures to replace an HOU

5 Replace the ONT with a new unit:

a On a flat surface, such as a desk, substitute a replacement ONT for the old ONT; go to

step 8.

b On a wall. The G-241G-A can be wall-mounted with or without a fiber storage tray.

Note — If the Emerson 24W AC/DC Power Adapter or the Delta

DUPS-1232GA will be used, the ONT must be mounted a minimum of

31.5 in (0.8 m) above the floor. If the Delta DUPS-1232A will be used, the ONT must be mounted a

minimum of 59 in (1.5 m) above the floor.

i Slide the old ONT upward and then away from the two mounting screws until the

ONT is free of the wall.

ii Slide the wall mount keyholes on the ONT enclosure or fiber storage tray of the

replacement ONT down over the mounting screws until it is securely seated.

c In a wall-mounted outdoor enclosure.

i Unfasten the G-241G-A ONT by turning the brackets to the open position and

remove the unit; see Figure 14.

Issue: 01 DRAFT << doc part number tbd >> 67

DRAFT

Page 68

Procedures to replace an HOU

Figure 14 G-241G-A ONT mounted in an outdoor enclosure

HOU Product Guide

Mounting hole

ONT bracket

Mounting hole

ONT bracket

Mounting hole

28068

ii Position the replacement G-241G-A ONT within the outdoor enclosure and

between the ONT brackets, as shown in Figure 14.

iii Secure the G-241G-A ONT by turning the brackets to the closed position.

Warning — Do not overtighten the ONT bracket when securing the

G-241G-A ONT to the outdoor enclosure. The unit can become skewed and compromise the environmental seal of the ONT mounted in the outdoor enclosure.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 69

HOU Product Guide Procedures to replace an HOU

6 To ground a G-241G-A ONT:

Danger 1 — Hazardous electrical voltages and currents can cause

serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits. For more information on grounding safety, see chapter 12.

Danger 2 — Make sure all sources of power are turned off and have no

live voltages present on feed lines or terminals. Use a voltmeter to measure for voltage before proceeding.

Danger 3 — Always contact the local utility company before connecting

the enclosure to the utilities.

a An indoor desktop or wall-mounted G-241G-A ONT is grounded by the 3-pin power

adapter or a grounded UPS.

Warning — Do not connect the ground lug of the G-241G-A ONT for

indoor installations; the ONT is grounded by the power adapter or UPS.

b A G-241G-A ONT mounted in an outdoor enclosure must be grounded with a

permanent ground wire. Connect a single #6 to #14 AWG ground wire to the recessed ground lug on the

G-241G-A ONT. The ground wire exits from the back of the ONT unit in the same way as the cables.

7 Connect the RF video coaxial cable; see Figure 13.

8 Route up to four Ethernet cables to the RJ-45 ports, as shown in Figure 13. Connect the

Ethernet cables.

9 Route up to two POTS cables to the RJ-14 ports, as shown in Figure 13. Connect the POTS

cables.

10 If required, have approved service personnel who are trained to work with optic fiber clean

the fiber optic connection. See the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information about fiber optic handling, inspection, and cleaning.

Danger — Fiber optic cables transmit invisible laser light. To avoid eye

damage or blindness, never look directly into fibers, connectors, or adapters.

Issue: 01 DRAFT << doc part number tbd >> 69

DRAFT

Page 70

Procedures to replace an HOU

11 Connect the fiber optic cable to a G-241G-A ONT.

i Route the fiber optic cable to the ONT. ii Loosen the lock screw on the fiber optic connection clip. iii Lift the connection clip up. iv Plug the fiber optic cable with SC/APC adapter into the fiber optic connector; see Figure

v Lower the clip so that it secures the fiber optic cable. vi Tighten the lock screw.

12 Install the power supply according to manufacturer specifications.

HOU Product Guide

Warning — Be careful to maintain a bend radius of no less than 1.5

inches (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber.

13.

Warning — Units must be powered by a Listed or CE approved and

marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A.

13 Connect the power cable with an 8-pin Molex connector or 3-pin power adapter to the ONT

unit.

14 For a G-241G-A ONT installed in an outdoor enclosure with an FSST, coil the excess cable

in a clockwise direction allowing it to exit the lower right cable exit port.

Note — Observe the following:

• There must be approximately 18 in. (45.72 cm) of cable stub exiting

the FSST at the right cable exit point.

• The FSST stores a maximum of 75 ft (22.86 m) of cable.

15 Power up the ONT unit by using the ON/OFF power switch.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 71

HOU Product Guide Procedures to replace an HOU

16 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and

Troubleshooting Guide.

Note — A new SLID or the old SLID may be used with the replacement

ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details.

17 If necessary, reset the ONT.

i Locate the Reset button. ii Insert the end of a straightened paper clip or other narrow object into the hole in the

Reset button to reset the ONT.

18 Verify the ONT LEDs, voltage status, and optical signal level; see the 7368 Hardware and

Cabling Installation Guide.

19 Activate and test the services; see the 7368 Hardware and Cabling Installation Guide.

20 For a G-241G-A ONT installed in an outdoor enclosure, close the access cover of the outdoor

enclosure and secure using the pin-in-hex screw.

21 STOP. This procedure is complete.

Issue: 01 DRAFT << doc part number tbd >> 71

DRAFT

Page 72

Procedures to replace an HOU

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 73

HOU Product Guide Configure an HOU

11 Configure an HOU

11.1 Remote configuration

11.2 Local configuration

11.1 Remote configuration

The WPON manager and Nokia Altiplano can be used t o configure an HOU remotely; see the AP Product Guide for more information about the WPON manager and Noki a Altiplano.

11.2 Local configuration

Local craft terminal access for an HOU is provided through a Bluetooth interface (classical Bluetooth, reach greater than 20 m) on the HOU.

The Bluetooth interface provides access to a Blueto oth server that can be used for local management of the HOU by a Bluetooth-equipped mobile phone or tablet or other external device.

You can configure the following through the Blu etooth interface of an HOU:

need info on how to configure the HOU through the Bluetooth

interface

Issue: 01 DRAFT << doc part number tbd >> 73

DRAFT

Page 74

Configure an HOU

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 75

HOU Product Guide Grounding safety

12 Grounding safety

12.1 Ground safety information

<< this section is based on the equivalent section in the G-241-G-A ONT

product guide, with “ONT” changed to “HOU” - the section needs to be reviewed carefully to make sure that it is complete and accurate with respect to the HOU

Improper grounding can result in personal injury or equipment damage. See below for specific dangers and considerati ons when handling grounding equipment.

Danger — Hazardous electrical voltages and currents can

cause serious physical harm or death. Always use insulated tools and follow prop er safety precautions when connecting or disconnecting power circuits.

Danger — Make sure all sources of power are turned off and

have no live voltages present on feed lines or termina ls. Use a voltmeter to measure for voltage before proceedi ng.

Danger — Always contact the local utility company before

connecting the enclosure to the utilities.

Danger — You must connect the HOU to earth ground before

connecting the power supply to the HOU.

<< change “power supply” to “Cat5 cable that provides power over Ethernet”? >>

Danger — The earth bonding terminal shal l be connected to an

approved earth connection before the ac power is applied.

Issue: 01 DRAFT << doc part number tbd >> 75

DRAFT

Page 76

Grounding safety

HOU Product Guide

Danger — Earthing and bonding of the HOU must comply with

the ANSI-specific requirements found in NEC Article 250.

• Insulation - The grounding conductor must be insulated and

listed as suitable for the purpose.

• Material - The grounding conductor sha ll be copper or other

corrosion-resistant conductive material stranded or solid.

• Size - The grounding conductor must be a minimum of

14 AWG per UL investigation. If local code or regulations require more, follow per local codes or regulation.

• Length - The primary protector gr ounding conductor must be

as short as practicable. In one- and two-family dwellings, the primary protector grounding conductor must be as short as practicable, not to exceed 20 ft (6.0 m) in length.

• If the building or structure ser ved has no groundi ng means,

as described in 800.100 (B)(1) or (B)(2)(1) of NEC Article 250, the communications grounding conductor must be connected to either of the following:

a) to any one of the individual electrodes described i n 250.52 (A)(1), (A)(2), (A)(3), or (A)(4).

b) to an effectively grounded metal structure or to a ground rod or pipe not less than 5 ft (1.5 m) in length and 1/ 2 in. (12.7 mm) in diameter, driven, where practical, into permanently damp earth, and the communications ground rod shall be bonded to the power grounding electrode system in accordance with 800.100 (D).

Warning — This equipment is ESD sensitive. Proper ESD

protection must be used when entering the TELCO Access portion of the HOU.

Warning — ANSI-specific: If using cable other th an the

recommended brands, select only UL-list ed cable, rated for the specific installation.

Warning — ANSI-specific: If using cable other th an the

recommended brands, select only UL-list ed cable, rated for the specific installation.

Note — Earthing and bonding of the HOU must comply with the

ETSI-specific requirements found in local electrical wiring codes.

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 77

HOU Product Guide Grounding safety

Note — Observe all local and national laws and regulations

that may be applicable to this install ation.

Issue: 01 DRAFT << doc part number tbd >> 77

DRAFT

Page 78

Grounding safety

HOU Product Guide

<< doc part number tbd >> Issue: 01 DRAFT

DRAFT

Page 79

Customer document and product support

Customer documentation

Customer Documentation Welcome Page

Technical Support

Customer Documentation Technica l Support

Documentation feedback

Customer Documentation Feedback

Page 80

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference

operation.

FCC Radiation Exposure Statement:

received, including interference that may cause undesired

This equipment c

omplies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

<< doc part number tbd >>

Nokia 7577WPONHOU User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Preface

1.1 Scope

1.2 Audience

1.3 Required knowledge

1.4 Acronym s and initialisms

1.5 Assistance and ordering phone numbers

1.6 Nokia quality processes

1.7 Safety information

1.8 Documents

1.9 Special information

1.9.1 Steps with options or substeps

1.10 Multiple PDF document search

HOU Product Guide HOU legal and data privacy information

2.1 Purpose

2.2 Data privacy

2.2.1 Privacy rules

2.2.2 Privacy impact assessment

Table of contents

List of figures

List of tables

HOU Product Guide ETSI environmental and CRoHS guidelines

3.1 Environmental labels

3.1.1 Overview

3.1.2 Environmental rel ated labels

3.1.2.1 Products below Maximum Concentration Value (MCV) label

3.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label

3.2 Hazardous Substances Table (HST)

3.3 Other environmental requiremen ts

3.3.1 HOU environmental requirements

3.3.2 Storage

3.3.3 Transportation

3.3.4 Stationa ry use

3.3.5 Thermal limitations

3.3.6 Material content compliance

3.3.7 End-of-life collection and treatment

4 ETSI safety guidelines

4.1 Safety instructions

4.1.1 Safety instruction boxes

4.1.2 Safety-related labels

4.2 Safety standards compliance

4.2.1 EMC, EMI, and ESD compliance

4.2.2 Equipment safety standard compliance

4.2.3 Environmental standard comp liance

4.2.4 Resistibility requirements compliance

4.2.5 Acoustic noise emission standard compliance

4.3 Electrical safety guidelines

4.3.1 Power supplies

4.3.2 Cabling

4.3.3 Protective earth

4.4 ESD safety guidelines

4.5 Envir onmental requireme nts

5 ANSI safety guidelines

5.1 Safety instructions

5.1.1 Safety instruction boxes in customer documentation

5.1.2 Safety-related labels

5.2 Safety standards compliance

5.2.1 EMC, EMI, and ESD standards compliance

5.2.2 Equipment safety standard compliance

5.2.3 Environmental standards c omplianc e

5.2.4 Resistibility requirements compliance

5.3 Electrical safety guidelines

5.3.1 Power supplies

5.3.2 Cabling

5.3.3 Protective earth

5.4 ESD safety guidelines

5.5 Envir onmental requireme nts

6 WPON solution overview

6.2 WPON solution

6.1 << something to consider >>

6.2.1 APs and AP pairs

6.2.2 HOUs

6.2.3 WPONs

6.2.4 More information about the WPON solution

6.3 Compatible CPE

7 HOU unit data sheet

7.1 HOU part numbers and identification