Nokia 7577WPONHOU User Manual

WPON Product Overview

WPON HOU 8VHU0DQXDO

WPON Product Overview

3TG-00038-AAAA-TCZZA

Issue: 01

June 2018

Nokia — Proprietary and confidential Use pursuant to applicable agreements

WPON Product Overview

Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners.

The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein.

Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements.

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview Preface

1Preface

This preface provides general information about the documentation for the Nokia WPON solution.

1.1 Scope

The documentation for the WPON solution provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the products in the current release of the WPON solution. The documentation for the WPON solution provides some information about configuring products in the WPON solution.

1.2 Audience

The documentation for the WPON solution is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the products that are part of the WPON solution.

Note — The HOU installation guide that is in the document set

for the WPON solution has been prepared for use by subscribers if it considered appropriate for them, rather than operational personnel, to install or replace an HOU. The HOU installation guide can be used by operational personnel as well.

1.3 Required knowledge

The reader must be familiar with general telecommunications principles.

1.4 Acronyms and initialisms

Expansions and optional descriptions of most acronyms and initialisms used in this document are provided in the glossary that is in this document.

1.5 Assistance and ordering phone numbers

Nokia provides global technical support through regional call centers. Phone numbers for the regional call centers are available at the following URL: http://support.alcatel-lucent.com

For ordering information, contact your Nokia sales representative.

Issue: 01 3TG-00038-AAAA-TCZZA 3

Preface

WPON Product Overview

1.6 Nokia quality processes

Nokia’s WPON quality practices are in compliance with TL 9000 requirements.These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met. The customer or its representatives may be allowed to perform on-site quality surveillance audits, as agreed upon during contract negotiations

1.7 Safety information

For safety information, see the appropriate safety guideline chapters.

1.8 Documents

Documents are available from Nokia using ALED or OLCS.

Procedure 1 To download a ZIP file package of the customer documentation

1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you

are a new user and require access to this service, please contact your Nokia sales representative.

2 From the Technical Content for drop-down menu, choose the product.

3 Click on Downloads: Electronic Delivery.

4 Choose Documentation from the drop-down menu and click Next.

5 Select the image from the drop-down menu and click Next.

6 Follow the on-screen directions to download the file.

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview Preface

Procedure 2 To access individual documents

Individual PDFs of customer documents are also accessible through the Nokia Customer Support website.

1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you

are a new user and require access to this service, please contact your Nokia sales representative.

2 From the Technical Content for drop-down menu, choose the product.

3 Click on Manuals and Guides to display a list of customer documents by title and part

number. You can filter this list using the Release drop-down menu.

4 Click on the PDF to open or save the file.

1.9 Special information

The following are examples of how special information is presented in this document.

Danger — Danger indicates that the described activity or

situation may result in serious personal injury or death; for example, high voltage or electric shock hazards.

Warning — Warning indicates that the described activity or

situation may, or will, cause equipment damage or serious performance problems.

Caution — Caution indicates that the described activity or

situation may, or will, cause service interruption.

Note — A note provides information that is, or may be, of

special interest.

Issue: 01 3TG-00038-AAAA-TCZZA 5

Preface

1.9.1 Steps with options or substeps

When there are options in a step, they are identified by letters. When there are required substeps in a step, they are identified by roman numerals.

Procedure 3 Example of options in a step

At step 1, you must choose option a or b.

1 This step offers two options. You must choose one of the following:

a This is one option.

b This is another option.

2 You must perform this step.

WPON Product Overview

Procedure 4 Example of required substeps in a step

At step 1, you must perform a series of substeps within the step.

1 This step has a series of substeps that you must perform to complete the step. You must

perform the following substeps:

i This is the first substep.

ii This is the second substep.

iii This is the third substep.

2 You must perform this step.

1.10 Multiple PDF document search

You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file.

Note — The PDF files in which you search must be in the same

folder.

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview Preface

Procedure 5 To search mu

1 Open Adobe Acrobat Reader.

2 Choose Edit→Search from the Acrobat Reader main menu. The Search PDF panel appears.

3 Enter the search criteria.

4 Click on the All PDF Documents In radio button.

5 Select the folder in which to search using the drop-down menu.

6 Click on the Search button.

Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol.

ltiple PDF files for a common term

Issue: 01 3TG-00038-AAAA-TCZZA 7

WPON Product Overview

1 Preface.............................................................................................3

1.1 Scope ..........................................................................................................3

1.2 Audience......................................................................................................3

1.3 Required knowledge....................................................................................3

1.4 Acronyms and initialisms .............................................................................3

1.5 Assistance and ordering phone numbers ....................................................3

1.6 Nokia quality processes...............................................................................4

1.7 Safety information........................................................................................4

1.8 Documents ..................................................................................................4

1.9 Special information ......................................................................................5

1.9.1 Steps with options or substeps....................................................................6

1.10 Multiple PDF document search ...................................................................6

2 ETSI environmental and CRoHS guidelines...............................17

2.1 Environmental labels .................................................................................17

2.1.1 Overview....................................................................................................17

2.1.2 Environmental related labels .....................................................................17

2.1.2.1 Products below Maximum Concentration Value (MCV) label....................17

2.1.2.2 Products containing hazardous substances above Maximum

2.2 Hazardous Substances Table (HST).........................................................19

2.3 Other environmental requirements ............................................................20

2.3.1 Environmental requirements......................................................................20

2.3.2 Storage ......................................................................................................20

2.3.3 Transportation ...........................................................................................20

2.3.4 Stationary use............................................................................................20

2.3.5 Thermal limitations ....................................................................................20

2.3.6 Material content compliance......................................................................21

2.3.7 End-of-life collection and treatment ...........................................................21

Table of contents

Concentration Value (MCV) label ..............................................................18

3 ETSI safety guidelines..................................................................23

3.1 Safety instructions .....................................................................................23

3.1.1 Safety instruction boxes ............................................................................23

3.1.2 Safety-related labels..................................................................................24

3.2 Safety standards compliance ....................................................................24

3.2.1 EMC compliance .......................................................................................25

3.2.2 Equipment safety standard compliance.....................................................25

3.2.3 Environmental standard compliance .........................................................25

3.2.4 Laser product standard compliance ..........................................................25

3.3 Electrical safety guidelines ........................................................................26

3.3.1 Power supplies ..........................................................................................26

3.3.2 Cabling ......................................................................................................26

3.3.3 Protective earth .........................................................................................26

3.4 ESD safety guidelines ...............................................................................27

3.5 Environmental requirements......................................................................27

Issue: 01 3TG-00038-AAAA-TCZZA

WPON Product Overview

4 ANSI safety guidelines .................................................................29

4.1 Safety instructions .....................................................................................29

4.1.1 Safety instruction boxes in customer documentation ................................29

4.1.2 Safety-related labels..................................................................................30

4.2 Safety standards compliance ....................................................................31

4.2.1 EMC, EMI, and ESD compliance...............................................................31

4.2.2 Equipment safety standard compliance.....................................................32

4.3 Electrical safety guidelines ........................................................................32

4.3.1 Power supplies ..........................................................................................32

4.3.2 Cabling ......................................................................................................33

4.3.3 Protective earth .........................................................................................33

4.4 ESD safety guidelines ...............................................................................33

4.5 Environmental requirements......................................................................33

5 WPON solution overview .............................................................35

5.1 WPON solution ..........................................................................................35

5.1.1 APs ............................................................................................................37

5.1.1.1 Head AP ....................................................................................................38

5.1.1.2 Relay AP....................................................................................................38

5.1.1.3 Extension AP .............................................................................................38

5.1.2 HOUs......................................................................................................... 39

5.1.3 APs and HOUs in WPONs ........................................................................39

5.2 WPON topologies ......................................................................................39

5.2.1 Basic WPON topology ...............................................................................39

5.2.2 Wireless daisy chain topology ...................................................................40

5.3 WPON architecture....................................................................................42

5.3.1 Underlay network.......................................................................................42

5.3.2 Overlay network.........................................................................................43

5.4 WPON services .........................................................................................43

5.5 WPON management .................................................................................45

5.5.1 WPON management through the WPON manager ..................................45

5.5.2 WPON management through the Nokia Altiplano .....................................46

5.5.3 WPON management through Bluetooth ...................................................47

5.6 WPON planning considerations.................................................................48

5.7 Compatible CPE ........................................................................................48

6 AP unit data sheet ........................................................................49

6.1 AP part numbers and identification............................................................49

6.2 AP general description ..............................................................................51

6.3 AP software and installation feature support .............................................52

6.4 Subscriber traffic interfaces on the AP ......................................................52

6.4.1 AP physical connections and components ................................................53

6.4.2 AP wireless components ...........................................................................55

6.5 AP LED information ...................................................................................55

6.6 AP specifications .......................................................................................56

6.7 AP wireless specifications ......................................................................... 57

6.8 Performance monitoring statistics .............................................................58

6.9 Functional blocks.......................................................................................58

6.10 AP standards compliance..........................................................................59

6.10.1 Energy-related products standby and off modes compliance....................60

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview

6.10.2 AP compliance statement..........................................................................61

7 HOU unit data sheet .....................................................................63

7.1 HOU part numbers and identification ........................................................ 63

7.2 HOU general description ...........................................................................64

7.3 HOU software and installation feature support..........................................64

7.4 Subscriber traffic interfaces on the HOU ...................................................65

7.4.1 HOU physical connections and components............................................. 65

7.4.2 HOU wireless components ........................................................................66

7.5 HOU LED information................................................................................66

7.6 HOU specifications ....................................................................................67

7.7 HOU wireless specifications ......................................................................68

7.8 Performance monitoring statistics .............................................................69

7.9 Functional blocks.......................................................................................69

7.10 HOU standards compliance.......................................................................69

7.10.1 Energy-related products standby and off modes compliance....................70

7.10.2 HOU compliance statement.......................................................................71

8 Installing or replacing APs and HOUs ........................................73

8.1 Installation scenarios for APs and HOUs ..................................................73

8.2 Replacement scenarios for APs and HOUs ..............................................73

8.3 AP installation and replacement ................................................................73

8.4 HOU installation and replacement.............................................................74

8.4.1 HOU pre-installation tasks.........................................................................74

8.4.2 HOU pre-replacement tasks ...................................................................... 75

9 Configure an AP or HOU ..............................................................77

9.1 AP configuration ........................................................................................ 77

9.1.1 Local configuration of an AP......................................................................77

9.2 HOU configuration .....................................................................................77

9.2.1 Local configuration of an HOU ..................................................................78

10 Fiber optic maintenance ..............................................................79

10.1 Purpose .....................................................................................................79

10.2 General......................................................................................................79

10.2.1 Handling considerations ............................................................................79

10.2.2 Fiber optic jumper cable care ....................................................................80

10.2.3 Acceptance criteria for fiber optic device inspections................................80

10.2.4 Acceptance criteria ....................................................................................81

10.3 Prerequisites..............................................................................................83

10.4 Parts list.....................................................................................................84

10.5 Recommended tools..................................................................................84

10.6 Procedure..................................................................................................85

11 Glossary ........................................................................................89

Issue: 01 3TG-00038-AAAA-TCZZA

WPON Product Overview

2 ETSI environmental and CRoHS guidelines...............................17

Figure 1 Products below MCV value label...............................................................18

Figure 2 Products above MCV value label ..............................................................19

Figure 3 Recycling/take back/disposal of product symbol .......................................21

4 ANSI safety guidelines .................................................................29

Figure 4 Sample safety label ...................................................................................31

5 WPON solution overview .............................................................35

Figure 5 High-level representation of the WPON solution .......................................36

Figure 6 WPON example with a 7360 ISAM............................................................37

Figure 7 Example of an AP pair...............................................................................38

Figure 8 Example of a linear daisy chain topology ..................................................41

Figure 9 Example of a daisy chain topology that has an AP pair ............................42

Figure 10 WPON service support with an ISAM........................................................44

Figure 11 WPON service independent an ISAM .......................................................44

6 AP unit data sheet ........................................................................49

Figure 12 AP physical connections............................................................................54

Figure 13 AP LED location ........................................................................................56

Figure 14 Functional blocks of an AP ........................................................................59

List of figures

7 HOU unit data sheet .....................................................................63

Figure 15 HOU physical connections ........................................................................65

Figure 16 HOU LED location .....................................................................................67

Figure 17 Functional blocks of an HOU.....................................................................69

10 Fiber optic maintenance ..............................................................79

Figure 18 Parts of a fiber optic cable .........................................................................80

Figure 19 Single-mode end-face zones.....................................................................82

Figure 20 Preferred condition of fiber optic end-face.................................................82

Issue: 01 3TG-00038-AAAA-TCZZA

WPON Product Overview

3 ETSI safety guidelines..................................................................23

Table 1 Safety labels..............................................................................................24

4 ANSI safety guidelines .................................................................29

Table 2 Safety labels..............................................................................................30

6 AP unit data sheet ........................................................................49

Table 3 AP part numbers and descriptions ............................................................50

Table 4 AP accessories..........................................................................................51

Table 5 AP subscriber traffic interfaces..................................................................53

Table 6 AP physical connections and components ................................................54

Table 7 AP LED behavior description.....................................................................56

Table 8 AP physical specifications .........................................................................57

Table 9 AP power consumption specifications .......................................................57

Table 10 AP environmental requirements ................................................................57

Table 11 Wireless specifications for the AP .............................................................58

7 HOU unit data sheet .....................................................................63

Table 12 HOU part numbers and descriptions .........................................................63

Table 13 HOU subscriber traffic interfaces............................................................... 65

Table 14 HOU physical connections and components.............................................66

Table 15 HOU LED behavior description .................................................................67

Table 16 HOU physical specifications ......................................................................67

Table 17 HOU power consumption specifications.................................................... 68

Table 18 HOU environmental requirements .............................................................68

Table 19 Wireless specifications for the HOU ..........................................................68

List of tables

8 Installing or replacing APs and HOUs ........................................73

Table 20 HOU installation and replacement actions ................................................74

Table 21 Pre-installation tasks for the HOU .............................................................75

Table 22 Pre-replacement tasks for the HOU ..........................................................75

10 Fiber optic maintenance ..............................................................79

Table 23 Single-mode end-face inspection acceptance criteria ...............................81

Table 24 Acceptable and unacceptable conditions for fiber optic end-faces............83

Issue: 01 3TG-00038-AAAA-TCZZA

WPON Product Overview ETSI environmental and CRoHS guidelines

2 ETSI environmental and CRoHS

guidelines

This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of AP and HOU equipment. This chapter also includes environmental operation parameters of general interest.

2.1 Environmental labels

This section describes the environmental instructions that are provided with the customer documentation, equipment, and location where the equipment resides.

2.1.1 Overview

CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold and imported in the territory of the mainland of the People’s Republic of China. EIP refers to products and their accessories manufactured by using electronic information technology, including electronic communications products and such subcomponents as batteries and cables.

2.1.2 Environmental related labels

Environmental labels are located on appropriate equipment. The following are sample labels.

2.1.2.1 Products below Maximum Concentration Value (MCV) label

Figure 1 shows the label that indicates a product is below the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). Products with this label are recyclable. The label may be found in this documentation or on the product.

Issue: 01 3TG-00038-AAAA-TCZZA

ETSI environmental and CRoHS guidelines

18986

Figure 1 Products below MCV value label

WPON Product Overview

2.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label

Figure 2 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). The number contained inside the label indicates the Environment-Friendly User Period (EFUP) value. The label may be found in this documentation or on the product.

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview ETSI environmental and CRoHS guidelines

18985

Figure 2 Products above MCV value label

Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories. These values are based on manufacturers' extensive practical experience of the design, manufacturing, maintenance, usage conditions, operating environments, and physical condition of infrastructure and handsets after years of service. The values reflect minimum values and refer to products operated according to the intended use conditions. See “Hazardous Substances Table (HST)” for more information.

2.2 Hazardous Substances Table (HST)

This section describes the compliance of the AP and HOU equipment to the CRoHS standard when the product and subassemblies contain hazardous substances beyond the MCV value. This information is found in this user documentation where part numbers for the product and subassemblies are listed. It may be referenced in other documentation that describes the AP or HOU equipment.

In accordance with the People’s Republic of China Electronic Industry Standard Marking for the Control of Pollution Caused by Electronic Information Products (SJ/T11364-2006), customers may access the Nokia Hazardous Substance Table, in Chinese, from the following location:

• http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRo

HS.pdf

Issue: 01 3TG-00038-AAAA-TCZZA 15

ETSI environmental and CRoHS guidelines

2.3 Other environmental requirements

Observe the following environmental requirements when handling AP or HOU equipment.

2.3.1 Environmental requirements

See chapter 6 in this guide for more information about temperature ranges for the AP equipment and other AP specifications.

See chapter 7 in this guide for more information about temperature ranges for the HOU equipment and other HOU specifications.

2.3.2 Storage

WPON Product Overview

According to ETS 300-019-1-1 - Class 1.1, storage of AP and HOU equipment must be in Class 1.1, weather-protected, temperature-controlled locations.

2.3.3 Transportation

According to EN 300-019-1-2 - Class 2.3, transportation of AP and HOU equipment must be in packed, public transportation with no rain on packing allowed.

2.3.4 Stationary use

According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of AP and HOU equipment must be in a temperature-controlled location, with no rain allowed, and with no condensation allowed.

2.3.5 Thermal limitations

The thermal limitations for the AP and HOU equipment are:

• operating temperature (ambient): –30°C to 55°C (–22°F to 131°F)

• operating relative humidity: 5% to 85%

• short-term relative humidity: 5% to 95%, but not to exceed 0.024 kg of water/kg

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview ETSI environmental and CRoHS guidelines

2.3.6 Material content compliance

European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive applies to electrical and electronic products placed on the EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment. Nokia products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive.

Nokia has implemented a material/substance content management process. The process is described in: Nokia process for ensuring RoHS Compliance (1AA002660031ASZZA). This ensures compliance with the European Union Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2). With the process equipment is assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC) on Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances.

2.3.7 End-of-life collection and treatment

Electronic products bearing or referencing the symbol shown in Figure 3, when put on the market within the European Union (EU), shall be collected and treated at the end of their useful life, in compliance with applicable EU and local legislation. They shall not be disposed of as part of unsorted municipal waste. Due to materials that may be contained in the product, such as heavy metals or batteries, the environment and human health may be negatively impacted as a result of inappropriate disposal.

Note — In the European Union, a solid bar under the symbol for

a crossed-out wheeled bin indicates that the product was put on the market after 13 August 2005.

Figure 3 Recycling/take back/disposal of product symbol

Issue: 01 3TG-00038-AAAA-TCZZA 17

ETSI environmental and CRoHS guidelines

At the end of its life, AP and HOU equipment is subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE).

There can be different requirements for collection and treatment in different member states of the European Union.

In compliance with legal requirements and contractual agreements, where applicable, Nokia will offer to provide for the collection and treatment of Nokia products bearing the logo shown in Figure 3 at the end of their useful life, or products displaced by Nokia equipment offers. For information regarding take-back of equipment by Nokia, or for more information regarding the requirements for recycling/disposal of product, contact your Nokia account manager or Nokia take back support at sustainability.global@nokia.com.

WPON Product Overview

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview ETSI safety guidelines

3 ETSI safety guidelines

This chapter provides information about the mandatory regulations that govern the installation and operation of AP and HOU equipment in the ETSI market.

3.1 Safety instructions

This section describes the safety instructions that are provided in the customer documentation and on the AP and HOU equipment.

3.1.1 Safety instruction boxes

The safety instruction boxes are provided in the AP and HOU customer documentation. Observe the instructions to meet safety requirements.

The following is an example of the Danger box.

Danger — Possibility of personal injury.

The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm.

Do not proceed beyond a Danger box until the indicated conditions are fully understood and met.

The following is an example of the Warning box.

Warning 1 — Possibility of equipment damage.

Warning 2 — Possibility of data loss.

The Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-damaging situation or provides essential information to avoid the degradation of system operations or data.

Do not proceed beyond a warning until the indicated conditions are fully understood and met.

Issue: 01 3TG-00038-AAAA-TCZZA

ETSI safety guidelines

WPON Product Overview

The following is an example of the Caution box.

Caution 1 — Possibility of service interruption.

Caution 2 — Service interruption.

The Caution box indicates that the described activity or situation may, or will, cause service interruption.

Do not proceed beyond a caution until the indicated conditions are fully understood and met.

The following is an example of the Note box.

Note — Information of special interest.

The Note box provides information that assists the personnel working with AP or HOU equipment. It does not provide safety-related instructions.

3.1.2 Safety-related labels

The AP and HOU equipment is labeled with the specific safety instructions and compliance information that is related to a product, or product variant, of the equipment. Observe the instructions on the safety labels.

Table 1 provides sample safety labels on AP and HOU equipment.

Table 1 Safety labels

Description Label text

ESD warning Caution: This assembly contains an electrostatic sensitive device.

3.2 Safety standards compliance

This section describes AP and HOU equipment compliance with the European safety standards.

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview ETSI safety guidelines

3.2.1 EMC compliance

The AP and HOU equipment complies with the following EMC requirements:

• Electromagnetic compatibility of multimedia equipment - Emission requirements

CISPR 32, EN 55032

• Electromagnetic compatibility of multimedia equipment - Immunity requirements

CISPR 35, EN55035

• Electromagnetic Compatibility (EMC) standard for radio equipment and services;

Part 1: Common technical requirements; Harmonized Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU EN 301489-1

• Electromagnetic Compatibility (EMC) standard for radio equipment and services;

Part 17: Specific conditions for Broadband Data Transmission Systems; Harmonized Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU EN 301489-17

3.2.2 Equipment safety standard compliance

The AP and HOU equipment complies with the requirements of the following:

• EN 60950-1, Safety of Information Technology Equipment for use in a restricted

location (per R-269)

• IEC 60950-22, EN 60950-22: Information Technology Equipment- Safety - Part 22

Equipment to be installed Outdoors

3.2.3 Environmental standard compliance

The AP and HOU equipment complies with the EN 300 019 European environmental standards.

3.2.4 Laser product standard compliance

The AP and HOU equipment is not a laser product.

Issue: 01 3TG-00038-AAAA-TCZZA

ETSI safety guidelines

3.3 Electrical safety guidelines

3.3.1 Power supplies

WPON Product Overview

This section provides the electrical safety guidelines for the AP and HOU equipment.

Note 1 — The AP and HOU equipment complies with the U.S.

National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards.

Note 2 — The AP and HOU equipment complies with BS EN

61140.

The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property.

3.3.2 Cabling

The following are the guidelines regarding cables used for the AP and HOU equipment:

• All cables must be approved by the relevant national electrical code.

• Cables for connection to the AP equipment must be suitable for outdoor use.

• Cables for outdoor connection to the HOU equipment must be suitable for outdoor

use.

• The HOU equipment must be used with the cabling supplied with the equipment.

3.3.3 Protective earth

Earthing and bonding of the AP and HOU equipment must comply with the requirements of local electrical codes.

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview ETSI safety guidelines

3.4 ESD safety guidelines

The AP and HOU equipment is sensitive to ESD if opened. Operations personnel must observe the following ESD instructions when they handle the AP or HOU equipment.

Caution — This equipment is ESD sensitive if opened. Proper

ESD protections should be used if you open the AP or HOU.

Service personnel are not required to wear wrist straps when performing normal installation or maintenance activities.

3.5 Environmental requirements

See chapter 6 in this guide for more information about temperature ranges for the AP equipment and other AP specifications.

See chapter 7 in this guide for more information about temperature ranges for the HOU equipment and other HOU specifications.

During operation in the supported temperature range, condensation inside the AP and HOU equipment caused by humidity is not an issue because the AP and HOU are sealed units.

Issue: 01 3TG-00038-AAAA-TCZZA

WPON Product Overview ANSI safety guidelines

4 ANSI safety guidelines

This chapter provides information about the mandatory regulations that govern the installation and operation of the AP and HOU equipment in the North American or ANSI market.

4.1 Safety instructions

This section describes the safety instructions that are provided in the customer documentation and on the AP and HOU equipment.

4.1.1 Safety instruction boxes in customer documentation

The safety instruction boxes are provided in the AP and HOU customer documentation. Observe the instructions to meet safety requirements.

The following is an example of the Danger box.

Danger — Possibility of personal injury.

Do not proceed beyond a Danger box until the indicated conditions are fully understood and met.

The following is an example of the Warning box.

Warning 1 — Possibility of equipment damage.

Warning 2 — Possibility of data loss.

Do not proceed beyond a warning until the indicated conditions are fully understood and met.

Issue: 01 3TG-00038-AAAA-TCZZA

ANSI safety guidelines

WPON Product Overview

The following is an example of the Caution box.

Caution 1 — Possibility of service interruption.

Caution 2 — Service interruption.

The Caution box indicates that the described activity or situation may, or will, cause service interruption.

Do not proceed beyond a caution until the indicated conditions are fully understood and met.

The following is an example of the Note box.

Note — Information of special interest.

The Note box provides information that assists the personnel working with AP or HOU equipment. It does not provide safety-related instructions.

4.1.2 Safety-related labels

The AP and HOU equipment is labeled with specific safety compliance information and instructions that are related to a product, or product variant, of the equipment. Observe the instructions on the safety labels.

Table 2 provides examples of the text in the various AP and HOU equipment safety labels.

Table 2 Safety labels

Description Label text

UL compliance ETL/cETL

UL50E compliance Type 3

ESD warning Caution: This assembly contains electrostatic sensitive device.

FCC standards compliance Tested to comply with FCC standards for home or office use.

Operation conditions This device complies with Part 15 of the FCC Rules. Operation is

CE marking There are various CE symbols for CE compliance.

Figure 4 shows a sample safety label.

subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

3TG-00038-AAAA-TCZZA Issue: 01

WPON Product Overview ANSI safety guidelines

18533

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la class A est conforme a la norme NMB-003 du Canada

Tested to Comply with FCC Standards

FOR HOME OR OFFICE USE

COMMUNICATION SERVICE EQUIPMENT US LISTED 27FY Type 3R Enclosure - Rainproof

CAUTION

This Assembly Contains Electrostatic Sensitive Devices

Figure 4 Sample safety label

4.2 Safety standards compliance

This section describes the AP and HOU equipment compliance with North American safety standards.

Warning — Changes or modifications to this unit not expressly

approved by the party responsible for compliance could void the user's authority to operate the equipment.

4.2.1 EMC, EMI, and ESD compliance

The AP and HOU equipment complies with the following EMC, EMI, and ESD requirements:

• Federal Communications Commission PART 15-RADIO FREQUENCY DEVICES

Subpart C-INTENTIONAL RADIATORS Title 47 CFR Part 15. Part 15.247, Part

15.255

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

Issue: 01 3TG-00038-AAAA-TCZZA

interference to radio communications.

+ 58 hidden pages