Nokia 6555 User Manual

Nokia

6555

User Guide

Some of the contents in this manual may differ from your phone depending on the software of the phone or your service provider.

© 2007 AT&T Knowledge Ventures. All rights reserved. AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures. Subsidiaries and affiliates of AT&T Inc. provide products and services under the AT&T brand. Nokia is a registered trademark of Nokia Corporation. Printed in Mexico.

Nokia 6555 User Guide

9255446

Issue 1, Part No. 9255446

Nokia, Nokia Connecting People, Navi or registered trademarks of Nokia Corporation. Nokia tune is a sound mark of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of

, and Nokia Original En hancements logo are trademarks

their respective owners.

Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited.

Includes RSA BSAFE cryptographic or security protocol software from RSA Security.

Java is a trademark of Sun Microsystems, Inc.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

This product is licensed under the MPEG-4 Visual Patent Portfolio License (i) for personal and noncommercial use in connection with information which has been encoded in compliance with the MPEG-4 Visual Standard by a consumer engaged in a personal and noncommercial activity and (ii) for use in connection with MPEG-4 video provided by a licensed video provider. No license is granted or shall be implied for any other use. Additional information including that relating to promotional, internal and commercial uses may be obtained from MPEG LA, LLC. See http://www.mpegla.com

Nokia operates a policy of ongoing development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL NOKIA OR ANY OF ITS LICENSORS BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER CAUSED.

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TO REVISE THIS DOCU MEN T OR W ITHD RAW I T AT ANY TIME WITHOUT PRIOR NOTICE.

The availability of particular products and applications and services f or these products may vary by region. Please check with the Nokia dealer for details, and availability of language options.

Export controls

This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited.

FCC NOTICE

Your device may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service facility. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Nokia could void the user's authority to operate this equipment.

Contents

For your safety....................................................................................................... 5

General information............................................................................................. 8

1. Get started .................................................................................................... 10

2. Your phone.................................................................................................... 17

3. Call functions ............................................................................................... 23

4. Navigate the menus ................................................................................... 25

5. Push to Talk .................................................................................................. 26

6. Write text...................................................................................................... 30

7. Messaging ..................................................................................................... 32

8. Recent Calls.................................................................................................. 46

9. MEdia Net ..................................................................................................... 47

10. AT&T Mall...................................................................................................... 53

11. AT&T Music................................................................................................... 54

12. My Stuff......................................................................................................... 55

13. Address Book ................................................................................................ 64

14. Settings......................................................................................................... 67

15. PC connectivity............................................................................................ 77

16. Battery and charger information............................................................ 78

Care and maintenance ...................................................................................... 80

Additional safety information ......................................................................... 81

Index....................................................................................................................... 85

For your safety

Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.

SWITCH ON SAFELY

Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger.

ROAD SAFETY COMES FIRST

Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.

INTERFERENCE

All wireless phones may be susceptible to interference, which could affect performance.

SWITCH OFF IN HOSPITALS

Follow any restrictions. Switch the phone off near medical equipment.

SWITCH OFF IN AIRCRAFT

Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELLING

Do not use the phone at a refuelling point. Do not use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Follow any restrictions. Do not use the phone where blasting is in progress.

USE SENSIBLY

Use only in the positions as explained in the product documentation. Do not touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel may install or repair this product.

ENHANCEMENTS AND BATTERIES

Use only approved enhancements and batteries. Do not connect incompatible products.

For your safety

WATER-RESISTANCE

Your phone is not water-resistant. Keep it dry.

BACK-UP COPIES

Remember to make back-up copies or keep a written record of all important information stored in your phone.

CONNECTING TO OTHER DEVICES

When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.

EMERGENCY CALLS

Ensure the phone function of the device is switched on and in service. Press the end key as many times as needed to clear the display and return to the standby mode. Enter the emergency number, then press the call key. Give your location. Do not end the call unti l given permission to do so.

■ About your device

The wireless device described in this guide is approved for use on the WCDMA 850 and 1900, EGSM 850 and 900, and GSM 1800 and 1900 networks. Contact your service provider for more information about networks.

When using the features in this device, obey all laws and respect local customs, privacy and legitimate rights of others, including copyrights.

Copyright protections may prevent some images, music (including ringing tones), and other content from being copied, modified, transferred, or forwarded.

Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device on when wireless device use may cause interference or danger.

■ Network services

To use the phone you must have service from a wireless service provider. Many of the features require special network features. These features are not available on all networks; other networks may require that you make specific arrangements with your service provider before you can use the network services. Your service provider can give you instructions and explain what charges will apply. Some networks may have limitations that affect how you can use network services. For instance, some networks may not support all language-dependent characters and services.

For your safety

Your service provider may have requested that certain features be disabled or not activated in your device. If so, these features will not appear on your device menu. Your device may also have a special configuration such as changes in menu names, menu order, and icons. Contact your service provider for more information.

This device suppo rts WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protoc ols. Some features of this device, such as multimedia messaging (MMS), browsing, e-mail application, instant messaging, presence enhanced contacts, remote synchronization, and content downloading using the browser or MMS, require network support for these technologies.

■ Shared memory

The following features in this device may share memory: Tones and Graphics, Contacts, Text Messages, Multimedia, and Instant Messages, E-mail, Calendar, To-Do Notes, Java or more of these features may reduce the memory available for the remaining features sharing memory. For example, saving many Java applications may use all of the available memory. Your device may display a message that the memory is full when you try to use a shared memory feature. In this case, delete some of the information or entries stored in the shared memory features before continuing. Some of the features, such as text messages, may have a certain amount of memory specially allotted to them in addition to the memory shared with other features.

Games and Applications, and the Note application. Use of one

■ Enhancements

A few practical rules about accessories and enhancements

• Keep all accessories and enhancements out of the reach of small children.

• When you disconnect the power cord of any accessory or enhancement, grasp and pull the plug, not the cord.

• Check regularly that enhancements installed in a vehicle are mounted and are operating properly.

• Installation of any complex car enhancements must be made by qualified personnel only.

General information

■ Access codes

Security code

The security code (5 to 10 digits) helps to protect your ph one against unauthorized use. For more information on security codes, see "Security," p. 76.

PIN codes

The personal identification number (PIN) code and the universal personal identification number (UPIN) code (4 to 8 digits) help to protect your SmartChip card against unauthorized use. See "Security," p. 76.

The PIN2 code (4 to 8 digits) may be supplied with the SmartChip card and is required for some functions.

The module PIN is required to access the information in the security module. See "Security module," p. 51.

The signing PIN is required for the digital signature. See "Digital signature," p. 52.

PUK codes

The personal unblocking key (PUK) code and the universal personal unblocking key (UPUK) code (8 digits) is required to change a blocked PIN code and UPIN code, respectively. The PUK2 code (8 digits) is required to change a blocked PIN2 code. If the codes are not supplied with the SmartChip card, contact your local service provider for the codes.

Restriction password

The restriction password (4 digits) is required when using the Call restrict ion

service. See "Security," p. 76.

■ Configuration settings service

To use some of the network services, such as mobile internet services, MMS, Nokia Xpress audio messaging, or remote internet server synchronization, your phone needs the correct configuration settings. For more information on availability, contact your network operator, service provider, nearest authorized Nokia dealer, or visit the support area on the Nokia website, www.nokia.com/support

General information

When you have received the settings as a configuration message, and the settings are not automatically saved and activated, Configuration settings

received is displayed.

To save the settings, select Show > Save. If required, enter the PIN code supplied by the service provider.

To discard the received settings, select Exit or Show > Discard.

■ Download content

You may be able to download new content (for example, themes) to the phone (network service).

For the availability of different services and pricing, contact your service provider.

Important: Use only services that you trust and that offer adequate security and protection against harmful software.

■ Assisted Global Positioning System

Your phone may have Assisted Global Positioning System (A-GPS), a positioning system that uses an assistance server and reference network to make measurements and determine location. A-GPS is dependent on your network service. Contact your provider for additional information.

A-GPS may also utilize cellular radio networks for aiding in positioning in some circumstances where standalone GPS positioning is unavailable. This feature requires network support and coverage.

A-GPS should not be used for precise location measurement, and you should never rely solely on location data from the A-GPS module.

■ Nokia support

Check www.nokia.com/support or your local Nokia website for the latest version of this guide, additional information, downloads, and services related to your Nokia product.

On the website, you can get information on the use of Nokia products and services. If you need to contact customer service, check the list of local Nokia Care contact centers at www.nokia.com/customerservice

For maintenance services, check your nearest Nokia service center at

www.nokia.com/repair

Get started

1. Get started

■ Install SmartChip card and battery

Always switch the device off and disconnect the charger before removing the battery. Keep all SmartChip cards out of the reach of small children. For availability and information on using SmartChip card services, contact your

SmartChip card vendor. This may be the service provider, network operator, or other vendor.

This device is intended for use with BL-5C battery. Always use original Nokia batteries. See "Nokia battery authentication," p. 79.

Always switch off the power and disconnect the charger and any other device before removing the covers. Avoid touching electronic components while changing the covers. Always store and use the device with the covers attached.

Warning: Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous.

The SmartChip card and its contacts can easily be damaged by scratches or bending, so be careful when handling, inserting, or removing the card.

To remove the back cover of the phone, press (1) and slide the cover as shown (2).

Remove the battery as shown.

Open the SmartChip card holder (1) and lift the holder up (2).

Insert the SmartChip card properly into the holder.

Close the SmartChip card holder.

Replace the battery. To replace the back cover, align the tabs on the cover to the slots on the back of the phone (1). Push the cover into place as shown (2).

Get started

■ Insert a microSD card

Keep all microSD memory cards out of the reach of small children. A microSD card can be loaded with ringing tones, themes, tones,

images and videos. If you delete, reload, or replace this card, these functions and features may not function properly.

Use only compatible microSD cards with this device. Other memory cards, such as reduced size MultiMedia cards, do not fit in the microSD card slot and are not compatible with this device. Using an incompatible memory card may damage the memory card as well as the device, and data stored on the incompatible card may be corrupted.

Use only microSD cards approved by Nokia for use with this device. Nokia utilizes the approved industry standards for memory cards but not all other brands may function correctly or be fully compatible with this device.

1. Remove the back cover and the battery. Push the memory card holder forward (1)and swing card holder up (2),

2. Insert the card into the memory card holder with the gold-colored contact area facing down (3).

3. Close the card holder (3 and 4) and slide the card holder back in place (5). Replace the battery and back cover.

Memory card

Keep all memory cards out of the reach of small children.

Get started

You can use the microSD memory card to store your multimedia files such as video clips, music tracks, and sound files, images, and messaging data, and to back up information from phone memory.

Some of the folders in Tones & Graphics with content that the phone use, for example, Themes, may be stored on a memory card.

To insert and remove the microSD memory card see "Insert a microSD card," p. 12.

Format the memory card

When a memory card is formatted, all data on the card is permanently lost. Some memory cards are supplied preformatted and others require formatting. Consult your retailer to find out if you must format the memory card before you can use it.

To format a memory card, select Menu > My Stuff > Tones & Graphics or Games

& apps the memory card folder , Options > Format memory card > Yes.

When formatting is complete, enter a name for the memory card. An unformatted memory card may have NO NAME listed instead of Memory card.

Lock the memory card

To set a password to lock your memory card to help prevent unauthorized use, select

Menu > My Stuff > Tones & Graphics > the memory card folder > Options > Set password. The password can be up to eight characters long.

The password is stored in your phone, and you do not have to enter it again while you are using the memory card on the same phone. If you want to use the memory card on another phone, you are asked for the password. To delete the password, select Options > Delete password.

Check memory consumption

To check the memory consumption of different data groups and the available memory for installing new applications or software on your memory card, select Options > Details.

■ Charge the battery

Check the model number of any charger before use with this device. This device is intended for use when supplied with power from an AC-3U or AC-4U charger.

Warning: Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous.

For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any enhancement, grasp and pull the plug, not the cord.

Get started

1. Connect the charger to a wall socket.

2. Connect the charger to your phone.

A CA-44 charging adapter can be used with older charger models.

If the battery is completely discharged, it may take a few minutes before the charging indicator appears on the display or before any calls can be made.

The charging time depends on the charger used. Charging a BL-5C battery with the AC-4U charger takes approximately 2 hours and 20 minutes while the phone is in the standby mode.

■ Open and close the phone

Open and close the phone manually. When you open the fold of the phone, it opens up to approximately 165 degrees. Do not try to force the fold open more.

Depending on the selected theme, a tone sounds when the fold is opened or closed.

■ Switch the phone on and off

Warning: Do not switch the phone on when wireless phone use is

prohibited or when it may cause interference or danger.

To switch the phone on or off, press and hold the power key. See "Keys and parts," p. 17.

If the phone asks for a PIN or a UPIN code, enter the code (displayed as ****), and select OK.

Set the time, time zone, and date

Enter the local time, select the time zone of your location in terms of the time difference with respect to Greenwich Mean Time (GMT), and enter the date. See "Set time and date," p. 68.

Get started

■ Connect a headset

You can connect a universal 2.5 mm headset to your device. Connect the headset to the device as shown.

Connect stereo headphones

You can use 3.5 mm stereo headphones with your phone to listen to music. Connect the AD-61 headset adaptor to your headphones first. Then connect the AD-61 adaptor to your phone.

Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset where it can endanger your safety.

■ Antenna

Your device has an internal antenna located at the bottom of the phone.

Get started

Note: As with any other radio transmitting

device, do not touch the antenna unnecessarily when the device is switched on. Contact with the antenna affects call quality and may cause the device to operate at a higher power level than otherwise needed. Avoiding contact with the antenna area when operating the device optimizes the antenna performance and the battery life.

■ Phone strap

Remove the back cover of the phone. Insert a thread through the eyelet. Place the thread around the post of the phone as shown in the picture. Tighten the thread. Put the back cover back in place.

■ Digital rights management

Content owners may use different types of digital rights management (DRM) technologies to protect their intellectual property, including copyrights. This device uses various types of DRM software to access DRM-protected content. With this device you may be able to access content protected with WMDRM 10. If certain DRM software fails to protect the content, content owners may ask that such DRM software’s ability to access the new DRM-protected content be revoked. Revocation may also prevent renewal of such DRM-protected content already in your device. Revocation of such DRM software does not affect the use of content protected with other types of DRM or the use of non-DRM-protected content.

Digital rights management (DRM) protected content comes with an associated activation key that defines your rights to use the content. If your device has WMDRM protected content, both the activation keys and the content will be lost if the device memory is formatted. You may also lose the activation keys and the content in case the files on your device get corrupted. Losing the activation keys or the content may limit your ability to use the same content on your device again. For more information, contact your service provider.

2. Your phone

■ Keys and parts

1 Earpiece 2 Main display

key

3 Navi 4 Right selection key 5 Cellular Video key 6 End and power key 7 Keypad 8 PTT key 9 Volume and

camera/ video key

10 Micro USB connector 11 Charger connector 12 Call key 13 MEdia Net key 14 Left selection key 15 Universal headset

connector

16 Mini display

Your phone

■ Side key functions

The Push to Talk (PTT) key (8) and the Volume and camera/video key (9) have multiple functions:

• The PTT key is used to activate PTT and to talk to PTT contacts or groups, with the fold closed or open.

When the camera is activated, the key functions to capture a photo.

• During calls, the Volume key (9) functions only to increase or decrease volume.

Your phone

• While not in a call, the camera/video key (9) functions are available to activate the camera or video with the fold open, or closed for a self-portrait. See "Selfportrait," p. 57 for more information on self-portraits. With the fold closed, press and hold the key at the top until the camera is activated.

Once the camera is activated, use the key to zoom in or out. Press the PTT key (8) to capture a photo.

• With the fold closed, press and hold the camera/video key at the bottom to activate voice commands

■ Key functions

The Navi TM key and selections keys have the following functions:

1. Navi

2. Right selection key — connect to Music

3. Cellular Video — connect to Cellular Video. For more information visit

4. Camera and video key — connect to the camera or video

5. Left selection key — Options connects to shortcuts.

6. MEdia Net key — connect to MEdia Net’s wireless internet

key — scroll up, down, left, right, and

select with the center key

wireless.att.com/3g

■ Standby mode

When the phone is ready for use, and you have not entered any characters, the phone is in the standby mode.

Mini display

1 Network mode indicator 2 Signal strength of the cellular network 3 Battery charge status 4 Indicators 5 Network name or the operator logo 6 Time and date

Analog clock

The Mini display settings include a screensaver to display an analog clock. To show the clock, select

Menu > Settings > Mini display > Screen saver > Analog clock. The time-out default to display the clock

after closing the fold is ten seconds. To display the clock sooner, select Menu > Settings > Mini display > Screen

saver > Time-out and set the time to five seconds.

Main display

1 Network mode indicator 2 Signal strength of the cellular network 3 Battery charge status 4 Indicators 5 Network name or the operator logo 6 Clock 7 Main display 8 The left selection key 9 The middle selection key 10 The right selection key

Your phone

Right selection key

Music is the right selection key on your device. This menu provides access to the

music player, various music-related tools, music downloads, applications, and services. See "Music player," p. 58 for more information on using the music player.

Your phone

Active standby

In the active standby mode there is a list of selected phone features and information on the screen that you can directly access in the standby mode. To switch on or off the mode, select Menu > Settings > Main display > Active

standby > Active standby mode > On or Off.

In the active standby mode, scroll up or down to navigate the list. Left and right arrows at the beginning and end of a line indicate that further information is available by scrolling left or right. To end the active standby navigation mode, select Exit.

To organize and change the active standby mode, select Menu > Settings >

Main display > Active standby > Options > Change or Personalize view.

Indicators

You have unread messages.

You have n ew voic e mai l.

You have unsent, canceled or failed messages.

The phone registered a missed call.

, Your phone is connected to the instant messaging service, and the

availability status is online or offline.

You received one or several instant messages.

The keypad is locked.

The phone does not ring for an incoming call or text message.

The alarm clock is activated.

The countdown timer is running.

The stopwatch is running.

The phone is registered to the GPRS or EGPRS network.

A GPRS or EGPRS connection is established.

The GPRS or EGPRS connection is suspended (on hold).

A Bluetooth connection is active.

, Push-to-talk connection is active or suspended.

Your phone

If you have two phone lines, the second phone line is selected.

All incoming calls are forwarded to another number.

The loudspeaker is activated, or the music stand is connected to the phone.

Calls are limited to a closed user group.

The timed profile is selected.

, , , or A headset, handsfree, loopset, or music stand

enhancement is connected to the phone.

■ Keypad lock (keyguard)

Select Menu or Unlock, and press * within

1.5 seconds to lock or unlock the keypad. To set the automatic keyguard on with a time

delay, select Menu > Settings > Phone settings >

Automatic keyguard.

To answer a call when the keyguard is on, press the call key or open the phone. When you end or reject the call, the keypad automatically locks.

Security keyguard

The security keyguard requires a 5 to 10 digit code to protect against unauthorized use. The preset code is 12345. To change the code and activate the security keyguard, select Menu > Settings > Phone settings >

Security keyguard.

When the security keyguard is activated, enter the security code if requested. For more information, see Security keyguard, in "Phone settings," p. 74. When the automatic or security keyguard is on, calls still may be possible to the

official emergency number programmed into your device.

■ Flight mode

You can deactivate all radio frequency functions and still have access to offline games, calendar, and phone numbers. Use the flight mode in radio sensitive environments—on board aircraft or in hospitals. When the flight mode is active, is shown.

Select Menu > Settings > Set profile > Flight > Activate or Customize.

Your phone

To deactivate the flight mode, select any other profile. In the flight mode you can make an emergency call. Enter the emergency number,

press the call key, and select Yes when asked Exit flight profile? The phone attempts to make an emergency call.

When the emergency call ends, the phone automatically changes to the normal profile mode.

Warning: With the flight mode profile, you cannot make or receive any calls, including emergency calls, or use other features that require network coverage. To make calls, you must first activate the phone function by changing profiles. If the device has been locked, enter the lock code. If you need to make an emergency call while the device is locked and in the flight profile, you may be also able to enter an official emergency number programmed in your device in the lock code field and select Call. The device will confirm that you are about to exit flight profile to start an emergency call.

■ Functions without a SmartChip card

Several functions of your phone may be used without installing a SmartChip card (for example, the data transfer with a compatible PC or another compatible device). Without a SmartChip card, some functions appear dimmed in the menus and cannot be used.

For an emergency call, some networks may require that a valid SmartChip card is properly inserted in the device.

Call functions

3. Call functions

■ Make a voice call

1. Enter the phone number, including the area code.

For international calls, press * twice for the international prefix (the + character replaces the international access code), enter the country code, the area code without the leading 0, if necessary, and the phone number.

2. To call the number, press the call key. To increase the volume in a call, press the volume up key and to decrease

press the volume down key.

3. To end the call or to cancel the call attempt, press the end key.

To search for a name or phone number that you have saved in Address book, see"Find a contact," p. 64. Press the call key to call the number.

To access the list of dialed numbers, press the call key once in the standby mode. To call the number, select a number or name, and press the call key.

Speed dialing

Assign a phone number to one of the speed-dialing keys, 2 to 9. See "Speed dial list," p. 66. Call the number in either of the following ways:

• Press a speed-dialing key, then the call key.

•If Speed dialing is set to On, press and hold a speed-dialing key until the call begins. See Speed dialing in "Call settings," p. 73.

Enhanced voice dialing

You can say the name saved in the contact list of the phone to make a phone call. Voice commands are not language-dependent. To set the language, see Vo ice

playback lang. in "Phone settings," p. 74.

Note: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely upon voice dialing in all circumstances.

1. In the standby mode, press and hold the right selection key or press and hold the volume down key. A short tone is played, and Speak now is displayed.

Call functions

2. Say the voice command clearly. If the voice recognition was successful, a list with matches is shown. The phone plays the voice command of the match on the top of the list. If the result is not the correct one, scroll to another entry.

Using voice commands to carry out a selected phone function is similar to voice dialing. See Voice commands in "My shortcuts," p. 68.

■ Answer or reject a call

To answer an incoming call, press the call key, or open the phone. To end the call, press the end key or close the phone.

To reject an incoming call, press the end key or close the phone. To reject an incoming call when the phone is closed, press and hold a volume key.

To mute the ringing tone, press a volume key when the phone is closed, or select

Silence when the phone is open.

Call waiting

To answer the waiting call during an active call, select Answer. The first call is put on hold. To end the active call, press the end key. To switch back to the first call without ending the second call, select Options > Swap.

To activate the call waiting function, see "Call settings," p. 73.

■ Options during a voice call

Many of the options that you can use during a call are network services. For availability, contact your service provider.

During a call, select Options and from the following: Call options are Mute or Unmute, Address book, Menu, Lock keypad, Record,

Loudspeaker or Handset.

Network services options are Answer or Reject, Hold or Unhold, PT T Contacts,

New call, Add to conference, End call, En d all calls, and the following: Touch tones — to send tone strings Swap — to switch between the active call and the call on hold Transfe r — to connect a call on hold to an active call and disconnect yourself Conference — to make a conference call of up to five persons Private call —to discuss privately in a conference call

Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.

Navigate the menus

4. Navigate the menus

The phone offers you an extensive range of functions, which are grouped into menus.

1. To access the menu, select Menu. To change the menu view, select Options > Main menu view > Grid,

Grid with labels, or Tab.

To rearrange the menu, scroll to the menu you want to move, and select

Options > Organize > Move. Scroll to where you want to move the menu,

and select OK. To save the change, select Done > Yes.

2. Scroll through the menu, and select an option (for example, Settings).

3. If the selected menu contains further submenus, select the one you want (for example, Call).

4. If the selected menu contains further submenus, repeat step 3.

5. Select the setting of your choice.

6. To return to the previous menu level, select Back. To exit the menu, select Exit.

Push to Talk

5. Push to Talk

Select Menu > PTT. Push to Talk (PTT) is a two-way radio service available over a GSM cellular network

(network service). You can use PTT to have a conversation with one person or with a group of people

having compatible devices and service. While you are connected to the PTT service, you can use the other functions of the phone.

To check availability and costs, and to subscribe to the service, contact your network operator. Service availability may differ from that for normal calls. Visit

wireless.att.com/ptt

Before you can use the PTT service, you must define the required PTT service settings. See "PTT Settings," p. 29.

Always switch PTT off before switching the phone off or removing the battery.

■ Switch PTT on and off

To disconnect from the PTT service, select Menu > PTT > PTT settin gs > PTT

Service > Off.

To connect to the PTT service, select Menu > PTT. If you have added groups to the phone, you are automatically joined to the active groups. There may be a brief delay while PTT connects.

Connection Indicators

These indicators appear on the standby screen next to the clock.

PTT is connected; your status is Available

Service is disconnected

Information is waiting

Your status is Do Not Disturb

for additional information.

Push to Talk

■ Add Contacts

You can add individual contacts or create contact groups to call several people at once.

Add a one-to-one contact

To add a contact to the PTT contacts list, select Menu > PTT > Add Contact. Enter the name and telephone number of the new contact. An invitation is sent to the person.

Add a contact group

You can save a group of contacts so you can call them collectively. To add a PTT contact group, select Menu > PTT > Add Group and name the group. To add an existing contact to the group, select From PTT contacts and mark the

contacts you want added to the new group. To add a new contact to the group, select Enter Manually. Enter the name and

telephone number of the new contact. An invitation is sent to the person.

■ Make and receive a PTT call

Warning: Do not hold the device near your ear when the loudspeaker is

in use, because the volume may be extremely loud.

To make a group call, a one-to-one call, or a call to multiple recipients, you must hold the PTT key as long as you talk. To listen to the response, release the PTT key.

You can check the login status of your contacts in Menu > PTT > PTT Contact s. To add a contact, select Menu > PTT > Add Contact. See "Add a one-to-one contact," p. 27 for more information.

Contact status indicators

These indicators appear next to your contacts and provide information about their connection status.

Contact is available

Contact is available with phone set to vibrate or silent

Do not disturb; you cannot contact this person

Invitation is in progress; you cannot contact this person

Contact has PTT switched off; you cannot contact this person

Push to Talk

Make a one-to-one call

To start a one-to-one call from the list of contacts to which you have added the PTT telephone number, select Menu > PTT > PTT Contacts. Scroll to a contact, and press and hold the PTT key while talking. Remember that you must release the PTT key to receive their reply.

To start a one-to-one call from the list of PTT groups, select PTT Contacts, scroll to the desired group, and select View. Scroll to the desired contact, and press and hold the PTT key while talking.

Make a group call

To make a call to a group, select PTT Contac ts in the PTT menu, scroll to the desired group, and press and hold the PTT key while talking.

Make a PTT call to multiple recipients

To select multiple PTT contacts from the contact list, create a Quick Group. The recipients receive an incoming call. If a recipients phone is set to silent or vibrate, they must accept the call in order to participate.

1. Select Menu > PTT > PTT Contacts and mark the desired contacts. The Quick

Group is automatically created.

2. Press and hold the PTT key to start the call. The group name is shown on the display, as soon as members join the call.

3. Press and hold the PTT key to talk to them. Release the PTT key to hear the response.

4. Press the end key to terminate the call.

Receive a PTT call

A short tone notifies you of an incoming PTT call. Information, such as the group, the phone number, or the nickname of the caller are displayed.

You can either accept or reject an incoming one-to-one call if you have set the phone to silent or vibrate.

When you press and hold the PTT key while the caller is talking, you hear a queuing tone. Release the PTT key, and wait for the other person to finish; then you can press and hold the PTT key and begin talking.

Push to Talk

■ Change from PTT to mobile call

You can convert a one-to-one or group PTT call to a standard mobile call if you initiated the PTT call. Anytime during the PTT call select Options > Convert to Cellular . The call recipient(s) can then join your mobile call by pressing the PTT key.

■ Call Me Alerts

If you make a one-to-one call and do not get a response, you can send a request for the person to call you back.

Send a Call Me Alert

You can send a Call Me Alert in the following ways: To send a Call Me Alert from the contacts list in the PTT menu, select PTT

contacts. Scroll to a contact, and select Options > Call Me Alert.

To send a Call Me Alert from the group list in the PTT menu, select PTT contacts , and scroll to the desired group. Select View, scroll to the desired contact, and select Options > C all Me Alert.

Respond to a Call Me Alert

When someone sends you a Call Me Alert, Please call (sender’s name) is displayed in the standby mode.

To call the sender, press and hold the PTT key. To send a Call Me Alert to the sender, select Options > Call Me Alert .

■ Voice Messages

You can send a voice message to one of your PTT contacts or groups. From the PTT

contacts menu, select the individual or group to receive the voice message.

Select Options > Voice Messages. Push and hold the PTT key while speaking. Release the PTT key to deliver the message.

■ PTT Settings

Select Menu >PTT > PTT Settings.

My Availability — to set your PTT status to Available or Do Not Disturb Contact Alerts — to set a notification for when a contact becomes available Set My Name — to set how your PTT name appears to your contacts and groups Auto Accept Invites — to set the phone to automatically accept invitations from

other PTT users

PTT Service — to switch the PTT service on or off

+ 93 hidden pages