Nokia 6225 Service Manual 6rh27adisass

CCS Technical Documentation

RH-27 Series Transceivers

Disassembly

Issue 1 11/2003 Confidential ©2003 Nokia Corporation

RH-27

Disassembly CCS Technical Documentation

Step-by-Step Disassembly Instructions

Alway use ESD protection

Disassembly Instructions

Step-by-Step Disassembly Instructions (Model 6225)

1. Place the phone face down, press the Release Key,

and slide the battery cover downward.

2. Flip gently the A-cover from the down corner.
Remove the A-cover.

3. Remove the Keymat. 4. Spread the B-cover from both sides until snaps
inside will release it.

Page 2 ©2003 Nokia Corporation Confidential Issue 1 11/2003

RH-27

CCS Technical Documentation Disassembly

Step-by-Step Disassembly Instructions (Model 6225)

5. Remove the B-cover. 6. Remove the antenna.

Note! Use only a specified opening tool and be careful
not to damage the mechanical parts. Do not touch the
antenna plate inside without gloves.

7. Remove the screws (6 pieces) to get the module out

of the C-cover.

9. Remove the UI Module from the engine board. 10. The UI Module and the engine board are linked

8. Remove the module from the C-cover.

Note! Always use the specified tools.

together by two board-to-board connectors. Be careful
not to damage them.

Issue 1 11/2003 Confidential ©2003 Nokia Corporation Page 3

RH-27

Disassembly CCS Technical Documentation

Step-by-Step Disassembly Instructions (Model 6225)

11 . Note! The UI Module and the engine board are linked
together by two board-to-board connectors. Be careful
not to damage them.

13. Remove the Speaker by lifting it from the guiding

pin.

Note! The speaker is attached into the frame by adhe­sive tape. Therefore, it may not loosen easily.

12. Remove the Microphone by pressing it from its
edge or take the tweezers between the frame and the
microphone and lift it out from the frame.

14. To remove the Display shield, open the snaps from
both sides by using the specified tool and remove the
shield.

15. To remove the Display shield, open the snaps from

both sides by using the specified tool and remove the
shield.

Note! Be careful not to damage the shield.

16. To remove the LCD Module, keep it on a table by
using a soft cloth, and flip the LCD frame gently until
the LCD Module detaches.

Note! Be careful not to damage the sensitive parts. Do
not press the LCD module.

Page 4 ©2003 Nokia Corporation Confidential Issue 1 11/2003

RH-27

CCS Technical Documentation Disassembly

Step-by-Step Disassembly Instructions (Model 6225)

17. To remove the LCD Module, keep it on a table by

using a soft cloth, and flip the LCD frame gently until
the LCD Module detaches.

Note! Be careful not to damage the sensitive parts. Do
not press the LCD module.

19. Remove the Volume Key and the Power Key. 20. Remove the Vibra by lifting it out of its place.

18. Remove the UI board from the LCD frame.

Note! The UI board is attached into the frame by adhe­sive tape. Therefore, it may not loosen easily. Be careful
not to damage the LCD frame.

21. Remove the DC Jack by lifting it out of its place.

Note! Be careful not to damage the C-cover.

22. Lift the Release Spring by tweezing it from its
place.

Issue 1 11/2003 Confidential ©2003 Nokia Corporation Page 5

RH-27

Disassembly CCS Technical Documentation

Step-by-Step Disassembly Instructions (Model 6225)

23. Remove the Release Key by pressing the snaps

toward the center from the inside.

Page 6 ©2003 Nokia Corporation Confidential Issue 1 11/2003