Nilfisk-ALTO POSEIDON 5-50 PE, POSEIDON 2-35 PE, POSEIDON 5-51 PE+, POSEIDON 5-59 PE, POSEIDON 5-64 PE+ Operating Instructions Manual
...
106169306
Operating
instructions
POSEIDON PE
Copyright © 2013 Nilfisk-ALTO
User manual ..................................................... 3 - 18
Betriebsanleitung .............................................. 19 - 35
Manuel d‘instructions ........................................ 36 - 52
Gebruikershandleiding ...................................... 53 - 70
Manuale di istruzioni ......................................... 71 - 87
Instruktionsbog ................................................. 88 - 103
Instruksjonsbok ................................................. 104 - 119
Instruktionsbok .................................................. 120 - 134
Käyttöohje ......................................................... 135 - 150
3
POSEIDON PE
Original Instructions
Contents
Symbols
1 Important safety notes
2 Description
3 Before starting the
pressure washer
4 Operation and use
5 After using the pressure
washer
6 Maintenance
7 Troubleshooting
8 Further information
.................................................................................................4
.................................................................................................4
2.1 Intended use .............................................................................7
2.2 Operating elements ..................................................................7
3.1 Setting up the pressure washer ................................................8
4.1 Connections .............................................................................8
4.2 Start the pressure washer ......................................................10
4.3 Using detergents ....................................................................11
5.1 Switching off the pressure washer .........................................12
5.2 Disconnecting supply lines .....................................................12
5.3 Storing the cleaner (frost-free) ...............................................12
6.1 Maintenance plan ...................................................................13
6.2 Maintenance work ..................................................................13
...............................................................................................16
8.1 Recycling the pressure washer ..............................................17
8.2 Guarantee ..............................................................................17
8.3 Technical data ........................................................................18
8.4 Declaration of Conformity .......................................................18
4
POSEIDON PE
Original Instructions
Symbols Before starting
up your highpressure washer
for the fi rst time,
this instruction
manual must be
read through carefully. Save the
instructions for later use.
Safety instructions
marked with this
symbol must be
observed to
prevent danger
to persons.
This symbol is used
to mark safety
instructions
that must be
observed to prevent
damage to the machine and its
performance.
This symbol
indicates tips
and instructions to
simplify work and to
ensure a safe operation.
For your own safety
This appliance is not intended
for use by persons (including
children) with reduced physical,
sensory or mental capabilities,
or lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
High pressure washers shall
not be used by children or
untrained personnel.
Children should be supervised
to ensure that they do not play
with the appliance.
Warning
Inhalation of aerosols can be
hazardous to health.
Where applicable use a device
in order to avoid or reduce
aerosols production, e.g., a
shield covering the nozzle.
For protection against aerosols
use a respiratory mark of class
FFP 2 or higher.
General
Use of the high-pressure
washer is subject to the
applicable local regulations.
In addition to the operating
instructions and the binding
accident prevention regulations
in the country of use, the
generally recognised rules
for safe working must also be
observed.
Any method of use endangering
the safety of persons or
equipment is forbidden.
Transport
Transport of the high pressure
washer is easy on its large
wheels.
For safe transport in and on
vehicles we recommend to
prevent the equipment from
sliding and tilting by fi xing it with
belts.
For transport at temperatures
around or below 0°C, antifreeze should be drawn into the
pump beforehand (see chapter
5.3).
Before starting the washer
Before use, check that the high
pressure washer is in a safe
and proper condition.
Operate the pressure washer
only in an upright position!
Please observe the regulations
and provisions applicable in
your country. Before putting
the high-pressure washer into
service, carry out a visual check
of all the major components.
CAUTION!
High-pressure water jets can
be dangerous if misused. The
jet must not be directed at
persons, animals, live electrical
equipment or the pressure
washer itself.
1 Important safety notes
5
POSEIDON PE
Original Instructions
Wear appropriate protective
clothing, hearing and eye
protectors.
Do not direct the jet towards
yourself or towards other
persons in order to clean
clothes or footwear.
During operation of the washer,
recoil forces are produced at
the spray lance and, when
the lance is held at an angle,
a torque is also created. The
lance must therefore be held
fi rmly in both hands.
Do not run belt driven units
without the belt cover.
Do not use the washer when
other people without protective
clothing are in the working area.
Check that cleaning will not
result in dangerous substances
(e.g. asbestos, oil) being
washed off the object to be
cleaned and harming the
environment.
WARNING!
This machine has been
designed for use with the
cleaning agent supplied
or recommended by the
manufacturer. The use of other
cleaning agents or chemicals
may adversely affect the safety
of the machine.
Risk of explosion – Do not spray
flammable liquids.
Do not clean delicate parts
made of rubber, fabric, etc. with
the 0° jet. Always adjust the
distance and thus the pressure
of the nozzle to the surface,
which is to be cleaned to avoid
any damage to the surface
being cleaned.
Do not use the high-pressure
hose for lifting loads.
NOTE!
The maximum permissible
working pressure and
temperature are printed on the
high-pressure hose.
Do not continue to use the
washer if the high pressure
hose is damaged.
WARNING!
Ensure an adequate air
circulation. Do not cover
the washer or operate it in
inadequately ventilated rooms!
WARNING!
Ensure, that any exhaust
emissions are not in a vicinity of
air intakes.
Never use the machine in areas
where there is danger of fi re
or explosion. When using the
pressure washer, stand at least
1 m from buildings, etc.
Store the pressure
washer where it will not
be exposed to frost!
Never operate the pressure
washer without water. Even
brief shortages of water result
in severe damage to the pump
seals.
Switch off the cleaner after
max. 3 minutes.
Water connection
This high pressure
washer is only
allowed to be
connected with the
drinking water
mains, when an appropriate
backfl ow preventer has been
installed, Type BA according to
EN 60335-2-79. The backfl ow
preventer can be ordered under
number 106411177,106411178,
106411179,106411184. The
length of the hose between the
backfl ow preventer and the high
pressure washer must be at
least 12 metres (min diameter
3/4 inch) to absorb possible
pressure peaks. Operation by
suction (for example from a
rainwater vessel) is carried out
without backfl ow preventer.
Recommended suction set:
61256. As soon as water has
fl own through the BA valve, this
water is not considered to be
drinking water any more.
Operation
WARNING!
Incorrect fuels shall not be used
as they may prove hazardous.
CAUTION!
Never spray electrical
equipment with water: danger
for persons, risk of shortcircuiting.
Maintenace and repair
CAUTION!
Before cleaning and servicing
the high pressure washer,
always remove the ignition
plug cable fi rst.
Carry out only the maintenance
operations described in the
operating instructions.
Use only original Nilfi sk-ALTO
spare parts. Do not make any
technical modifi cations to the
high pressure washer.
Ensure that the machine is regularly serviced by Authorised NilfiskALTO dealers in accordance with
the maintenace plan. Failure to do
so will invalidate the warranty .
6
POSEIDON PE
Original Instructions
CAUTION!
High pressure hoses, fi ttings
and couplings are important
for the safety of the washer.
Use only high pressure parts
approved by the manufacturer!
Failure to observe these
instructions can endanger your
safety.
Please contact the Nilfi skALTO service department or an
authorised specialist work-shop
for all other maintenance or
repair work!
Testing
The cleaner conforms to
the German „Guidelines for
Liquid Spray Jet Devices“.
The high-pressure cleaner
must be subjected to a safety
examination in accordance
with the „Accident Prevention
Regulations for Working with
Liquid Spray Jet Devices“ as
required, but at least every
12 months, by an authorised
inspector and this report must
be saved.
The complete „Accident
Prevention Regulations for
Working with Liquid Spray Jet
Devices“ are available from
the Carl Heymanns Verlag
KG, Luxemburger Strasse
449, 50939 Cologne or from
the appropriate association of
employers’ liability insurances.
Unloader valve
Unacceptably high pressure
is fed back without residual
pressure via a bypass line into
the intake line of the pump
when the safety device is
tripped.
The unloader valve is set and
sealed at the factory and must
not be adjusted.
Safety device
Locking device on spray gun:
The spray gun features a
locking device. When the pawl
is activated, the spray gun
cannot be ope rated.
O
I
7
POSEIDON PE
Original Instructions
2 Description
2.1 Intended use This high pressure washer has
been designed for professional
use in
- agriculture
- transport industry
- construction industry
etc.
2.2 Operating elements
1 Start/stop switch
2 Lance
3 Holder for lance
4 Holder for high pressure hose
5 High pressure hose
6 Spray gun
7 Water connection and water
inlet fi lter
8 Connection for high pressure
hose
9 Detergent hose
10 Oil level gauge
11 Regulation of water volume
12 Filling of oil
13 Handle
2
5
6
3
3
3
3
3
3
8
8
8
87 7
7
9
9
9
13
13
13
13
10 10/12
10
11
11
1
1
1
1
8
POSEIDON PE
Original Instructions
3 Before starting the pressure washer
3.1 Setting up the pressure
washer (does not apply
to POSEIDON 2-35 PE /
POSEIDON 3-39 PE)
1. Before using the pressure
washer for the fi rst time,
check it carefully to detect
any faults or damage.
2. In the event of any damage
contact your Nilfi sk-ALTO
dealer immediately.
3. Check whether the oil level
is in the middle of the oil
inspection glass, oil cup or
dip stick. This also applies to
machines with gear.
4 Operation and use
4.1 Connections
4.1.1 Connecting the lance to
the spray gun
1. Pull the blue quick-release
grip (A) of the spray handle
backwards.
2. Insert the nipple of the spray
lance (B) into the quickrelease connection and
release it.
3. Pull forward the spray lance
or any other accessory to
ensure correct mounting
before starting the machine.
NOTE!
Always remove any dirt from
the nipple before connecting
the lanse to the spray gun.
A
B
9
POSEIDON PE
Original Instructions
4.1.2 Connecting the high
pressure hose and the
water hose
1. Connect the high pressure
hose to the high pressure
inlet by means of the quick
coupling. Use max. 50 m
extension hose.
2. Before connecting the water
hose to the washer, rinse the
water hose briefl y to prevent
sand and other dirt from
entering into the washer.
3. Open the tap.
NOTE!
See chapter 8.3 for required
quantity of water and water
pressure.
In the case of poor water quality
(sand, etc.), we recommend
that a fi ne water fi lter is fi tted in
the water inlet.
4.1.3 Fuelling WARNING!
Always shut off the engine
and let it cool for at least two
minutes before fuelling.
Avoid spilling fuel.
If you do spill fuel when fuelling,
do not start the engine before
the spilled fuel has evaporated.
If the washer is on a trailer, any
fuel spills must be wiped up
before the machine is started.
Never expose the machine
to an open fl ame. Smoking is
prohibited during fuelling. Also
read the operating manual for
the fuel engine.
Note: Never operate the
ma chine in a closed room; the
exhaust fumes are dan ger ous.
Follow the safety instructions
in chapter 1!
10
POSEIDON PE
Original Instructions
4.2 Start the washer
4.2.1 Switching on the
washer when it is
connected to a water
supply
2. Unlock the spray gun and
activate it.
3. Lock the safety catch even
during short pauses.
NOTE!
Activate the
spray gun several
times at short intervals to vent
the system.
If it requires too much power to
start the engine, it can be
facilitated by removing the
spray lance and activate the
spray gun during startup.
4.2.2 Switching on the
washer when it is
connected to open
tanks (suction mode)
1. Before connecting the suction
hose to the washer, fi ll the
hose with water.
2. Start the washer.
3. Unlock the spray gun and
activate it.
4. When using this machine in
suction mode, fi rst ensure
that the system has been
bled of air by letting the
machine run without spray
lance mounted until all air
has escaped.
During work breaks of more
than three minutes, switch off
the washer.
NOTE!
For automatic
suction from a tank,
watercourse or similar sup ply,
the inlet hose must be fi lled
with water before you start. The
suction height
depends on the water
temperature. Max. suction
height (see section 8.3
Technical Data) is reached with
cold water (up to 8°C). With
70°C/60°C warm water, the
ma chine must be under or at
the water level.
If the water being suctioned
contains particles, a suction
fi lter must be mounted on the
end of the hose.
In case of risk of running sands,
a sand fi lter must be attached.
1. Start the engine. (See the
operating manual for the fuel
engine.)
11
POSEIDON PE
Original Instructions
4.2.3 Start POSEIDON PE
with electric starter
1. Start the engine by turning
the key (see the operating
instructions for the engine.
2. Check that the throttle lever
is adjusted correctly - need to
be in Run position.
4.3 Using detergents Detergent can be added by
means of the detergent injector.
1. Dilute detergent according
to the manufacturer's
instructions.
2. Set the pressure to the
lowest setting on the lance.
CAUTION!
Never allow
detergent to dry
on the surface to be cleaned
as this may cause damage.
12
POSEIDON PE
Original Instructions
5 After using the washer
5.1 Stop the pressure washer
1. Stop the engine.
2. Close the tap.
3. Operate the spray gun until
the wasser is depressurized.
4. Lock the safety catch.
Switching off POSEIDON PE
with electric start
1. Stop the washer by moving
the throttle lever to STOP
position.
2. Switch off the ignition by
turning the key to OFF
position.
5.2 Disconnecting supply
lines
1. Shut the fuel cock.
2. Remove the water hose from
the washer.
5.3 Storing the washer
(frost-protected)
1. Store the pressure washer in
a dry room without danger of
frost.
IMPORTANT!
If the high-pressure washer
is stored in a room with
temperatures around or
below 0°C, anti-freeze should
be drawn into the pump
beforehand:
1. Remove the water inlet hose
from the washer.
2. Remove the lance.
3. Start the washer and stop it
again after max. one minute.
4. Connect the suction hose
to the water inlet of the
washer and place it in a tank
containing anti-freeze.
5. Start the washer.
6. Hold the spray gun over the
tank containing anti-freeze
and activate it to start suction
of anti-freeze.
7. During suction operate the
spray gun two or three times.
8. Lift the suction hose from the
tank containing anti-freeze
and activate the spray gun to
pump out the remaining antifreeze.
9. Stop the washer.
13
POSEIDON PE
Original Instructions
6 Maintenance
6.1 Maintenance plan
weekly
every six
months or
500 operating
hours
as required
6.2.1 Clean water fi lter
•
6.2.2 Clean high pressure nozzle
•
6.2.3 Check oil level
•
6.2.4 Change oil - Note: First time after 50 hours
•
6.2.5 Check belts (only belt driven units)
•
Maintenance of motor according to separate operating instructions from the engine supplier
6.2 Maintenance work
6.2.1 Clean water fi lter
A water fi lter is fi tted on the
water inlet to prevent large
particles of dirt from entering
into the pump.
1. Unscrew the union nut.
2. Remove the fi lter and rinse it.
Replace damaged fi lter.
3. Tighten the union nut gently,
so as to avoid damaging the
gasket.
6.2.2 Clean high pressure
nozzle
A blocked nozzle causes
excessive pump pressure. It
must therefore be cleaned
immediately.
1. Stop the washer.
2. Remove the lance.
3. Clean the nozzle with a
needle.
4. Rinse the lance with water
from the nozzle side.
WARNING!
Use the cleaning needle only
when the spray lance has been
removed.
NOTE!
The fuel engine
stops automatically
if the oil level is low. You can
start the petrol engine again
once you have added oil (does
not apply to POSEIDON 2-35
PE).
14
POSEIDON PE
Original Instructions
6.2.3 Checking the oil level
(does not apply to
POSEIDON 2-35 PE /
POSEIDON 3-39 PE)
1. Check whether the oil level
is in the middle of the oil
inspection glass, oil cup or
dip stick. Top up with oil if
necessary (see section 8.3
for type of oil).
6.2.4 Changing the pump/
gear oil (does not apply
to POSEIDON 2-35 PE /
POSEIDON 3-39 PE)
1. Before changing the oil,
allow the pressure washer to
become warm.
2. Unscrew/open the plugs/lid at
the top and the bottom of the
pump.
3. Allow the oil to drain into a
suitable container (min. 1 l
capacity) and dispose of oil in
compliance with regulations.
4. Mount plug at the bottom of
the pump.
5. Fill pump with fresh oil (see
8.3 for oil type and quantity).
6. Check the oil level (see
6.2.3).
15
POSEIDON PE
Original Instructions
1. Remove the spark plug cable.
2. Dismantle the cover of the
V-belts.
3. Check the belts for any
damage or missing tension.
4. If required, replace the belts.
5. Mount the cover.
6. Mount the spark plug cable.
6.2.5 Check of V-belts
16
POSEIDON PE
Original Instructions
7 Troubleshooting
Fault
Pressure drop
Pressure fl uctuations
In suction mode
Excess pressure
The motor does not start
Cause
> Air in the system
> High-pressure nozzle
blocked/worn
> Pressure control on the lance
is not set correctly
> Engine speed too low
> Warm/loose belts
> Lack of water
> Pump/accessories partially
frozen
> Water inlet hose is too long or
its cross-section too small
> Lack of water caused by
blocked water fi lter
> Warm/loose belts
> Lack of water because max.
permissible suction height
has not been heeded
> Water too hot
> Pump draws in air (only
possible in suction mode)
> Engine’s throttle control is
defective (accessory)
> Low fuel level
> Low oil level in engine
> The pump is blocked or
frozen
Remedy
• Vent the system by operating
the spray gun several
times at short intervals. If
necessary, dismount the
lance (see section 4.2.2).
• Clean/replace the highpressure nozzle.
• Set the required working
pressure.
• Contact Nilfi sk-ALTO Service
Department.
• Contact Nilfi sk-ALTO Service
Department.
• Open the tap.
• Thaw machine and
accessories.
• Use prescribed size of water
inlet hose.
• Clean the water fi lter in the
water connection (never
operate the machine without
water fi lter mounted!)
• Contact Nilfi sk-ALTO Service
Department.
• See chapter 4.2.2.
• See chapter 4.2.2.
• Check that the suction set is
air-tight. Repeat aeration.
• Give less gas/contact Nilfi skALTO Service Department.
• Open fuel cock/fi ll with fuel.
• Fill with oil.
• Thaw machine/contact
Nilfi sk-ALTO Service
Department.
17
POSEIDON PE
Original Instructions
• Fill with oil.
• Fill with oil
• Clean.
• Fill the detergent tank.
• Adjust the lance to low
pressure.
> Low oil level in engine
> Low oil level in pump(does
not apply to POSEIDON 2-35
PE)
> Injector is dirty or suction
hose is blocked
> Detergent tank is empty
> The lance is not set to low
pressure
The motor stops
When a detergent injector is
used
Fault
Cause
Remedy
8 Further information
8.1 Recycling the pressure
washer
If the pressure washer is
discarded, make it unusable
immediately
1. Dismount the ignition plug.
The pressure washer contains
valuable materials that should
be recycled. Contact your local
waste disposal site. If you have
any queries, please contact
your local authorities or your
nearest dealer.
8.2 Guarantee Your Nilfi sk-ALTO product is
guaranteed for 12 months from
date of purchase (purchase
receipt must be presented) on
the following conditions:
• that defects are attributable
to fl aws or defects in
materials or workmanship.
(Usual wear and tear as well
as misuse are not covered
by the guarantee).
• that repairs have not been
carried out or attempted
by other than Nilfi sk-ALTOtrained service staff.
• that only original
accessories have been
applied.
• that the product has not
been exposed to abuse such
as knocks, bumps or frost.
• that the instructions in the
manual have been carefully
observed.
A warranty repair comprises the
replacement of defective parts,
but it does not cover freight and
packaging charges. Besides we
refer to national Sale of Goods
Act.
Any illegitimate guarantee
repair will be invoiced. (I.e.
malfunctions due to causes
mentioned in section “7
Trouble shooting” of the
instruction manual).
18
POSEIDON PE
Original Instructions
8.3 Technical data
POSEIDON
2-35 PE
POSEIDON
3-39 PE
POSEIDON
3-37 PE+
POSEIDON
5-50 PE
POSEIDON
5-51 PE+
POSEIDON
5-59 PE
POSEIDON
5-64 PE+
POSEIDON
7-61 PE+
Working pressure bar 180 165 150 240 225 250 250 220
Water fl ow (max) l/h 650 750 740 800 840 930 1000 1010
Water fl ow Q
IEC l/h 700 810 800 870 910 1000 1050 1120
Max. water inlet temperature °C 60 60 60 60 60 60 60 80
Min./max. water inlet pressure bar 1/10 1/10 1/10 1/10 1/10 1/10 1/10 1/10
Dimensions (LxWxH) mm
762 x
546 x 603
762 x
546 x 603
1067 x
686 x 660
1041 x
546 x 635
1067 x
686 x 660
1041 x
546 x 635
1067 x
686 x 660
800 x
690 x 810
Noise power level, LWA dB(A) 95.1 93.2 89.6 91 90.8 93.2 93.4 91.9
Thrust N 31.1 31.9 30.8 42.3 42.9 51.8 54.4 52.7
Suction height, primed
(at max. 8°C)
m 1.0 1.0 2.5 2.5 2.5 2.5 2.5 2.5
Oil quantity in pump/gear l - - 0.3 0.5 0.4 0.5 0.5 1.1
Oil quantity in motor l 0.5 1111111
Oil type (motor/gear) SAE 15-40
Oil type (pump) SAE 15-40
Castrol
Alphasyn
150
Vibrations < 2,5 m/s
2
We reserve the right to make alterations.
8.4 EC Declaration of Conformity
Declaration of Conformity
Product: High Pressure Washer
Type: POSEIDON PE
Description: 250 bar / 25 MPa
Petrol driven
The design of the unit corre sponds to the following pertinent
regulations:
EC Machine Directive
2006/42/EC
EC EMC Directive 2004/108/EC
EC-RoHS Directive 2011/65/EC
Applied harmonised standards: EN 2100-1
EN 55012:2007
EN 61000-6-1:2007
EN 60335-2-79
Applied international standards and technical specifi cations: DIN EN 60335-2-79
Name and address of the person autho rised to compile the
technical fi le:
Anton Sørensen
General Manager
, Technical Operations EAPC
Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Identity and signature of the person empowered to draw up the
declaration on behalf of the manufacturer:
Anton Sørensen
General Manager, Technical Operations EAPC
Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Place and date of the declaration Hadsund, 01.05.2013
HEAD OFFICE
DENMARK
Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Tel.: (+45) 4323 8100
www.nilfi sk-advance.com
SALES COMPANIES
ARGENTINA
Nilfi sk-Advance srl.
Herrera 1855, 6 fl oor, Of. A-604
ZC 1293 – Ciudad Autónoma
de Buenos Aires – Argentina
www.nilfi sk-alto.com
AUSTRALIA
Nilfi sk-ALTO
Unit 1, 13 Bessemer Street Blacktown
NSW 2148 Australia
www.nilfi sk-alto.com.au
AUSTRIA
Nilfi sk-ALTO
Geschäftsbereich der Nilfi sk-Advance GmbH
Metzgerstraße 68
A-5101 Bergheim/Salzburg
www.nilfi sk-alto.at
BELGIUM
Nilfi sk-Advance NV/SA
Riverside Business Park
Boulevard Internationalelaan 55
Bâtiment C3/C4 Gebouw
Bruxelles 1070 Brussel
www.nilfi sk.be
CHILE
Nilfi sk-Advance S.A.
San Alfonso 1462, Santiago
www.nilfi sk.com
CHINA
Nilfi sk-Advance Cleaning Equipment
(Shanghai) Co Ltd.
No. 4189, Yindu Road
Xinzhuang Industrial Park
Shanghai 201108
www.nilfi sk.cn
CZECH REPUBLIC
Nilfi sk-Advance s.r.o.
Do Certous 1
VGP Park Horní Pocernice, Budova H2
CZ-190 00 Praha 9
www.nilfi sk.cz
DENMARK
Nilfi sk-ALTO Danmark
Industrivej 1
Hadsund, DK-9560
www.nilfi sk-alto.dk
FINLAND
Nilfi sk-Advance OY Ab
Koskelontie 23E
Espoo, FI-02920
www.nilfi sk.fi
FRANCE
Nilfi sk-Advance SAS
Division ALTO
BP 246
91944 Courtaboeuf Cedex
www.alto-fr.com
GERMANY
Nilfi sk-ALTO
Geschäftsbereich der Nilfi sk-Advance AG
Guido-Oberdorfer-Straße 10
89287 Bellenberg
www.nilfi sk-alto.de
GREECE
Nilfi sk-Advance A.E.
8, Thoukididou Str.
Argiroupoli,Athens, GR-164 52
www.nilfi sk.gr
HOLLAND
Nilfi sk-Advance B.V.
Versterkerstraat 5
1322 AN ALMERE
www.nilfi sk.nl
HONG KONG
Nilfi sk-Advance Ltd.
2001 HK Worsted Mills Ind’l Bldg.
31-39 Wo Tong Tsui St.
Hong Kong, Kwai Chung, N.T.
www.nilfi sk.com
HUNGARY
Nilfi sk-Advance Kereskedelmi Kft.
H-2310 Szigetszentmiklós-Lakihegy
II. Rákóczi Ferenc út 10.
www.nilfi sk.hu
INDIA
Nilfi sk-Advance India Limited
Pramukh Plaza, ‘B’ Wing, 4th fl oor, Unit No. 403
Cardinal Gracious Road, Chakala
Andheri (East), Mumbai 400 099
www.nilfi sk.com
IRELAND
Nilfi sk-Advance
1 Stokes Place
St. Stephen’s Green
Dublin 2, Ireland
www.nilfi sk-alto.ie
ITALY
Nilfi sk-Advance S.p.A.
Strada Comunale Della Braglia, 18
Guardamiglio, Lombardia, I-26862
www.nilfi sk.it
JAPAN
Nilfi sk-Advance Inc.
1-6-6 Kita-Shinyokohama
Kouhoku-Ku
Yokohama 223-0059
www.nilfi sk-advance.co.jp
KOREA
NIlfi sk-Advance Korea
471-4, Kumwon B/D 2F,
Gunja-Dong, Gwangjin-Gu, Seoul
www.nilfi sk-advance.kr
MALAYSIA
Nilfi sk-Advance Sdn Bhd
SD 33, Jalan KIP 10
Taman Perindustrian KIP
Sri Damansara
52200 Kuala Lumpur
Malaysia
www.nilfi sk.com
MEXICO
Nilfi sk Advance de Mexico S. de R.L. de C.V.
Agustin M. Chavez 1, PB-004
Col. Centro Ciudad Santa Fe
C.P. 01210 México, D.F.
www.nilfi sk-advance.com.mx
NEW ZEALAND
Nilfi sk-Advance NZ Ltd
Danish House
6 Rockridge Avenue
Penrose Auckland NZ 1135
www.nilfi sk.com.au
NORWAY
Nilfi sk-Advance AS
Bjørnerudvejen 24
Oslo, N-1266
www.nilfi sk-alto.no
PERU
Nilfi sk-Advance S.A.C.
Calle Boulevard 162, Of. 703, Lima 33- Perú
Lima
www.nilfi sk.com
POLAND
Nilfi sk-Advance Sp. z.o.o
ul. 3-go Maja 8, Bud. B4
Pruszków, PL-05-800
www.nilfi sk-alto.pl
PORTUGAL
Nilfi sk-Advance, Lda.
Sintra Business Park
Zona Industrial Da Abrunheira
Edifi cio 1, 1o A
Sintra, P-2710-089
www.nilfi sk.pt
RUSSIA
Nilfi sk-Advance LLC
Vyatskaya str. 27, bld. 7, 1st fl oor
Moscow, 127015
www.nilfi sk.ru
SOUTH AFRICA
WAP South Africa (Pty) Ltd
12 Newton Street
1620 Spartan, Kempton Park
www.wap.co.za
SINGAPORE
Den-Sin
22 Tuas Avenue 2
Singapore
www.nilfi sk.com
SPAIN
Nilfi sk-Advance, S.A.
Torre D’Ara
Passeig del Rengle, 5 Plta.10ª
Mataró, E-0830222
www.nilfi sk.es
SWEDEN
Nilfi sk-Advance AB
Taljegårdsgatan 4
431 53 Mölndal
Tel.: +46 31 706 73 00
Web: http://www.nilfi sk-alto.se
SWITZERLAND
NA Sondergger AG
Nilfi sk-ALTO Generalvertretung
Mühlestrasse 10
CH-9100 Herisau
www.nilfi sk-alto.ch
TAIWAN
Nilfi sk-Advance Ltd.
Taiwan Branch (H.K.)
No. 5, Wan Fang Road, Taipei
www.nilfi sk-advance.com.tw
THAILAND
Nilfi sk-Advance Co. Ltd.
89 Soi Chokechai-Ruammitr
Viphavadee-Rangsit Road
Jomphol, Jatuchak
Bangkok 10900
www.nilfi sk.com
TURKEY
Nilfi sk-Advance Prof. Tem. Ek. Tic. A.S.
Serifali Mh. Bayraktar Bulv. Sehit Sk. No:7
Ümraniye, Istanbul 34775
www.nilfi sk.com.tr
UNITED KINGDOM
Nilfi sk-ALTO
Bowerbank Way, Gilwilly Industrial Estate
Penrith, Cumbria
GB-CA11 9BQ
www.nilfi sk-alto.co.uk
UNITED ARAB EMIRATES
Nilfi sk-Advance Middle East Branch
SAIF-Zone, P. O. Box 122298
Sharjah
www.nilfi sk.com
USA
Nilfi sk-Advance
14600 21st Ave. North
Plymouth MN 55447-3408
www.nilfi sk-alto.us
VIETNAM
Nilfi sk-Advance Co., Ltd.
No.51 Doc Ngu Str. Lieu Giai Ward
Ba Dinh Dist. Hanoi
www.nilfi sk.com
Loading...