Nilfisk MAXXI 4S-73S Instructions Manual

MAXXI 4-73S
Instruction manual .............................. 3 - 13
Betriebsanleitung ................................ 14 - 24
Manuel d’Instructions .......................... 25 - 36
Gebruikershandleiding ........................ 37 - 47
Manuale di istruzioni ........................... 48 - 58
Manual de instrucciones ..................... 59 - 70
Priročnik z navodili za uporabo ........... 71 - 81
Contents
1 Important safety
instructions
................................................................................15
2 Description
3 Before starting the washer
4 Operation
5 After using the machine
6 Maintenance
2.1 Purpose ..............................................................................17
2.2 Operating elements ............................................................17
3.1 Installation environment .....................................................18
3.1.1 Temperature conditions ...........................................18
3.1.2 Conditions of distance .............................................18
3.2 Mounting instructions .........................................................18
3.3 Setting up the machine .......................................................19
3.4 Connecting the high pressure hose ....................................19
3.5 Connecting the water supply ..............................................19
3.6 Electrical connection ..........................................................19
4.1 Connecting the spray lance to the spray gun .....................20
4.2 Switching on the washer ....................................................20
4.2.1 Switching on the washer when it is connected
to a water supply .....................................................20
4.2.2 Switching on the cleaner when it is connected
to open tanks (suction mode) ..................................20
4.3 Sleep function .....................................................................20
5.1 Switching off the machine ..................................................21
5.2 Disconnecting supply lines .................................................21
6.1 Maintenance plan ...............................................................21
6.2 Maintenance work ..............................................................21
6.2.1 Cleaning water inlet filter .........................................21
6.2.2 Checking the pump oil level ....................................22
6.2.3 Changing the pump oil ............................................22
7 Troubleshooting
8 Further information
...............................................................................23
8.1 Recycling the washer .........................................................24
8.2 Guarantee ..........................................................................24
8.3 Technical Specifications .....................................................24
8.4 EU Declaration of Conformity .............................................24
1 Important safety instructions
Symbols used to mark in­structions
For your own safety
The high-pressure washer may only be used by persons instruc ed in its use and who have been expressly authorised to do so.
Before using the high-pressure washer, be sure to also read the enclosed operat-
ing instructions and keep them within reach at all times.
Safety instructions in these operating instructions which
must be observed to prevent risks to persons are marked with this danger sym­bol.
Before starting the washer
If your 3-phase washer was supplied without a plug, have it fitted with a suitable 3-phase plug with earth conductor, by an electrician.
Before use, check that the high­pressure washer is safe and in proper condition.
This symbol is used to mark safety instruc­tions that must be observed to
prevent damage to the machine and its perform­ance.
This indicates tips
and in structions to simplify work and to ensure safe operation.
We strongly recommend that the power supply to the high pressure washer be connected via a residual current circuit breaker.
This device stops the supply of electricity if the leakage cur­rent to earth exceeds 30 mA for 30 ms or it has an earth tester circuit.
Although extremely easy to operate, children should not be allowed to use the washer.
General
Use of the high-pressure wash­er is subject to the applicable local regulations. Besides the operating instruc­tions and the binding accident prevention regulations valid in the country of use, observe recognised regulations for safe­ty and proper use. Do not use any unsafe work techniques.
Regularly check whether the electric cable is damaged or shows signs of ageing.
Use the high-pressure washer only when the electric cable is in a safe condition. (risk of elec­tric shock if damaged!).
Check the rated voltage of the high-pressure washer before connecting it to the mains power supply. Ensure that the voltage shown on the rating plate corresponds to the volt­age of the local mains power supply.
Please observe the regula­tions and provisions applicable in your country. Before putting the high-pressure washer into service, carry out a visual check of all the major components.
CAUTION! High-pressure water jets can be dangerous if misused. The jet must not be directed at persons, animals, live electri­cal equipment or the washer itself.
Wear appropriate protective clothing and eye protectors.
Do not direct the jet towards yourself or towards other per­sons in order to clean clothes or footwear.
During operation of the washer, recoil forces are produced at the spraying device and, when the spray lance is held at an angle, a torque is also created. The spraying device must therefore be held firmly in both hands.
Do not use the washer when other people without protective clothing are in the working area.
Check that cleaning will not result in dangerous substances (e.g. asbestos, oil) being washed off the object to be cleaned and harming the envi­ronment.
Do not clean delicate parts made of rubber, fabric, etc. with the 0° jet. Keep some distance between high pressure nozzle and surface in order to prevent the surface from damage.
Operation
CAUTION! Unsuitable extension cords can represent a source of danger. Always unwind cord from the reels completely to prevent the electric cable overheating.
When using an extension cord, connectors must be of water­tight construction.
When using an extension cord, check the minimum cross-sec­tions of the cable:
Cable length m
up to 20 m
20 to 50 m
Cross section
<16 A <25 A
ø1.5mm² ø2.5mm²
ø2.5mm² ø4.0mm²
Do not damage the electric ca­ble (e.g. by driving over it, pull­ing or crushing it). Disconnect the electric cable by pulling the plug only (do not pull or tug the electric cable).
Maintenance and repair
CAUTION! Always disconnect the ma­chine from the mains plug socket before cleaning or car­rying out maintenance work on the washer.
Carry out only the maintenance operations described in the operating instructions. Use only original spare parts. Do not make any technical modifications to the high-pres­sure washer.
Ensure that the machine is regularly serviced by Autho­rised dealers in accordance with the maintenace plan. Failure to do so will invalidate the warranty.
CAUTION! High-pressure hoses, fittings and couplings are important for the safety of the washer. Use only high-pressure parts approved by the manufac­turer!
Do not use the high-pressure hose for lifting loads.
NOTE!
The specifications of the high­pressure hose (max. permissi­ble pressure and temperature) are printed on the hose. Do not continue to use the washer if the electric cable or high-pressure hose is damaged. Ensure adequate air circulation. Do not cover the washer or op­erate it in inadequately ventila­ted rooms!
Store the washer where it will not be exposed to frost!
Never operate the washer without water. Even brief short­ages of water result in severe damage to the pump seals.
Electrical equipment
CAUTION! Never spray electrical equip­ment with water: danger for persons, risk of short­circuiting.
The washer may only be con­nected to a correctly installed plug socket.
Switching on the washer may cause voltage fluctuations. Voltage fluctuations should not occur if the impedance at the transfer point is less than 0.15 Ω. If in doubt ask your local electricity supplier.
If the electric cable is damaged, it must be replaced by autho­rized Service or an electrician to avoid danger before use of the cleaner is continued.
Use only the type of electric cable specified in the operating manual. Please contact the Service de­partment or an authorised spe­cialist work-shop for all other maintenance or repair work!
Testing
The washer conforms to the German „Guidelines for Li­quid Spray Jet Devices“. The high-pressure washer must be subjected to a safety examina­tion in accordance with the „Ac­cident Prevention Regulations for Working with Liquid Spray Jet Devices“ as required, but at least every 12 months, by an authorised inspector.
Loading...
+ 9 hidden pages