The TS100 is a tabletop, infrared sensor designed for
use with the Niles infrared extender systems.
Installed in a remote room location, the TS100 receives the
2
3
9
IR commands transmitted from your hand-held remote(s).
The IR commands are carried via a category 5 cable to
your A/V equipment in another room, and instantly
“repeated”.
The TS100 represents one of the 3 building blocks necessary to complete a Niles IR repeating system:
• IR Main System Unit—Models MSU140, MSU250,
MSU480 and MSU440Z.
• IR Sensors/Keypads—Models WS100, TS100, MS100,
MVC100IR, MS200, CS100 and the IntelliPad
• IR Flashers—Models MF1, MF1VF, MF2, MF2VF and the
IRB1.
An IR sensor expansion unit, Model IRH610, is available for
IR repeater systems used in more than six rooms.
®
.
T
ABLE-TOPINFRAREDREMOTE SENSOR
Features and Benefits
The TS100 offers a number of improvements over other
table-top IR sensors.
• Plasma-proof performance—allows placement of the TS100
near plasma displays.
• CFL interference resistant—expands installation flexibility to
areas with fluorescent lighting.
• Works under most lighting conditions, including indirect
sunlight—eliminates environmental restrictions.
• Universal system—compatible with virtually all brands of A/V
equipment and remote controls.
• Excellent IR receiving range—you get 18' to 30' of remote
control range (depending upon the strength of your handheld remote).
• 100% factory tested for pickup range and angle.
• Small size of only 2-7/8" wide x 1-1/16" high x 3-1/8 deep—
fits almost anywhere.
• Printed circuit board design uses surface mount technology
(SMT), assuring high reliability.
• Ideal for both home and commercial installations.
• Non-skid, non-scratch feet.
• Two year parts and labor warranty.
2
T
ABLE-TOPINFRAREDREMOTE SENSOR
”Tech Tip“
Wire size is
expressed by it's
AWG (American
Wire Gauge) number. The lower the
AWG number, the
larger the wire, i.e.,
20 AWG wire
is physically larger
than 22 AWG.
3
Installation Considerations
Type of Cable
The TS100 connects to the Niles infrared main system unit or
IRH610 sensor expansion hub with an individual home run of
category 5 cable. When running wires inside walls, most states
and municipalities in the U.S. specify that you must use a special type of wire. Usually, the requirement is that the wire has a
specific “CL” fire rating, such as “CL-2” or “CL-3”. Consult
your Niles dealer, building contractor, or local building and
inspection department if unsure about which type of wire is
best for your application.
MS100 Mounting Location
The TS100 is ideal for use in applications when ceiling or wall-
mounting is undesirable. Its small size and unobtrusive appearance makes it ideal for installation in existing homes or cabinets with great ease and minimal custom work. Installing the
TS100 close to the primary location of the user will ensure
best performance.
The TS100 is designed to mount over or under almost any flat horizontal surface. Convenient mounting locations for the TS100 are:
• On top of a television set
• On a shelf in an entertaiment center
• Under a shelf in an entertanment center
Receiving Range and Pickup Angle
The receiving range of the TS100 will vary according to the IR
output strength of the remote control being used. Remote
strength varies among brands depending on the number and
T
ABLE-TOPINFRAREDREMOTE SENSOR
12V DC power supply
(supplied with the
MSU250 IR main system unit) plugged into
an unswitched
AC outlet powers
the system
Bi-colored LED
Removable
connector pins
Figure 1 Parts guide.
Niles IR flasher
Stereo receiver
MSU250
Power, IR data, and power status signal
via category 5 wire
Connecting the TS100 to a Niles MSU250
IR main system unit broadcasting a status
12V DC power supply
(not supplied, Niles stock#
FG00665) plugged into the
switched outlet
TS100 IR sensor
Figure 2
feedback signal.
4
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.