Index ........................................................................................... 242
viii
For Your Safety
To prevent damage to your Nikon product or injury to yourself or to others,
read the following safety precautions in their entirety before using this equipment. Keep these safety instructions where all those who use the product will
read them.
The consequences that could result from failure to observe the precautions
listed in this section are indicated by the following symbol:
This icon marks warnings. To prevent possible injury, read all warn-
A
ings before using this Nikon product.
❚❚WARNINGS
Keep the sun out of the frame. Keep the
A
sun well out of the frame when
shooting backlit subjects. Sunlight
focused into the camera when the
sun is in or close to the frame could
cause a fire.
Turn off immediately in the event of mal-
A
function. Should you notice smoke or
an unusual smell coming from the
equipment or AC adapter (available
separately), unplug the AC adapter
and remove the battery immediately,
taking care to avoid burn s. Continued
operation could result in injury. After
removing the battery, take the equipment to a Nikon-authorized service
center for inspection.
Do not use in the presence of flammable
A
gas. Do not use electronic equipment
in the presence of flammable gas, as
this could result in explosion or fire.
Keep dry. Do not immerse in or expose
A
to water or handle with wet hands.
Failure to keep the product dry could
result in damage to the product, fire,
or electric shock, while handling the
product with wet hands could result
in electric shock.
Do not disassemble. Touching the prod-
A
uct’s internal parts could result in
injury. In the event of malfunction,
the product should be repaired only
by a qualified technician. Should the
product break open as the result of a
fall or other accident, remove the battery and/or AC adapter and then take
the product to a Nikon-authorized
service center for inspection.
Keep out of reach of children. Failure to
A
observe this precaution could result
in injury. In addition, note that small
parts constitute a choking hazard.
Should a child swallow any part of
this equipment, consult a physician
immediately.
Do not place the strap around the neck of
A
an infant or child. Placing the camera
strap around the neck of an infant or
child could result in strangulation.
Follow the instructions of airline and hos-
A
pital personnel.
ix
Do not remain in contact with the camera,
A
battery, or charger for extended periods
while the devices are on or in use. Parts of
the device become hot. Leaving the
device in direct contact with the skin
for extended periods may result in
low-temperature burns.
Do not leave the product where it will be
A
exposed to extremely high temperatures,
such as in an enclosed automobile or in
direct sunlight. Failure to observe this
precaution could cause damage or
fire.
Do not aim the flash at the operator of a
A
motor vehicle. Failure to observe this
precaution could result in accidents.
Observe caution when using a flash.
A
• Using the camera with the flash in
close contact with the skin or other
objects could cause burns.
• Using a flash close to the subject’s
eyes could cause temporary visual
impairment. The flash should be no
less than one meter (3 ft 4 in.) from
the subject. Particular care should
be observed when photographing
infants.
Avoid contact with liquid crystal. Should
A
the display break, care should be
taken to avoid injury due to broken
glass and to prevent the liquid crystal
from the display touching the skin or
entering the eyes or mouth.
Do not carry tripods with a lens or camera
A
attached. You could trip or accidentally
strike others, resulting in injury.
Do not touch the moving parts of the lens.
A
Failure to observe this precaution
could result in injury.
Observe proper precautions when handling
A
batteries. Batteries may leak, overheat,
rupture, or catch fire if improperly
handled. Observe the following precautions when handling batteries for
use in this product:
• Use only batteries approved for use
in this equipment.
• Do not short or disassemble the
battery.
• Do not expose the battery or the
camera in which it is inserted to
powerful physical shocks.
• Be sure the product is off before
replacing the battery. If you are
using an AC adapter, be sure it is
unplugged.
• Do not attempt to insert the battery
upside down or backwards.
• Do not expose the battery to flame
or to excessive heat.
• Do not immerse in or expose to
water.
• Replace the terminal cover when
transporting the battery. Do not
transport or store the battery with
metal objects such as necklaces or
hairpins.
• Batteries are prone to leakage when
fully discharged. To avoid damage
to the product, be sure to remove
the battery when no charge
remains.
• When the battery is not in use,
attach the terminal cover and store
in a cool, dry place.
x
• The battery may be hot immedi-
ately after use or when the product
has been used on battery power for
an extended period. Before removing the battery turn the camera off
and allow the battery to cool.
• Discontinue use immediately
should you notice any changes in
the battery, such as discoloration or
deformation.
Observe proper precautions when handling
A
the charger:
• Keep dry. Failure to observe this pre-
caution could result in injury or
product malfunction due to fire or
electric shock.
• Do not short the charger terminals.
Failure to observe this precaution
could result in overheating and
damage to the charger.
• Dust on or near the metal parts of
the plug should be removed with a
dry cloth. Continued use could
result in fire.
• Do not go near the charger during
thunderstorms. Failure to observe
this precaution could result in electric shock.
• Do not handle the plug or charger
with wet hands. Failure to observe
this precaution could result in injury
or product malfunction due to fire
or electric shock.
• Do not use with travel converters or
adapters designed to convert from
one voltage to another or with DCto-AC inverters. Failure to observe
this precaution could damage the
product or cause overheating or fire.
Use appropriate cables. When connect-
A
ing cables to the input and output
jacks, use only the cables provided or
sold by Nikon for the purpose to
maintain compliance with product
regulations.
xi
Notices
• No part of the manuals included
with this product may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form,
by any means, without Nikon’s prior
written permission.
• Nikon reserves the right to change
the specifications of the hardware
and software described in these
manuals at any time and without
prior notice.
Notice for Customers in Canada
CAN ICES-3 (B) / NMB-3 (B)
Notice for Customers in Europe
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
This symbol indicates that
electrical and electronic
equipment is to be collected separately.
The following apply only to
users in European countries:
• This product is designated for separate collection at an appropriate collection point. Do not dispose of as
household waste.
• Separate collection and recycling
helps conserve natural resources
and prevent negative consequences
for human health and the environment that might result from incorrect disposal.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
• Nikon will not be held liable for any
damages resulting from the use of
this product.
• While every effort has been made to
ensure that the information in these
manuals is accurate and complete,
we would appreciate it were you to
bring any errors or omissions to the
attention of the Nikon representative in your area (address provided
separately).
This symbol on the battery
indicates that the battery is
to be collected separately.
The following apply only to
users in European countries:
• All batteries, whether marked with
this symbol or not, are designated
for separate collection at an appropriate collection point. Do not dispose of as household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
xii
Notice for Customers in the U.S. A.
The Battery Charger
IMPORTANT SAFETY INSTRUCTIONS—SAVE THESE
INSTRUCTIONS
DANGER—TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS
For connection to a supply not in the U.S.A., use an attachment plug adapter
of the proper configuration for the power outlet if needed. This power unit
is intended to be correctly oriented in a vertical or floor mount position.
Federal Communications Commission (FCC) Radio Frequ ency Interference Statement
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not
installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to
try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced
radio/television technician for help.
CAUTIONS
Modifications
The FCC requires the user be notified
that any changes or modifications
made to this device that are not
expressly approved by Nikon Corporation may void the user’s authority to
operate the equipment.
Interface Cables
Use the interface cables sold or provided by Nikon for your equipment.
Using other interface cables may
exceed the limits of Class B Part 15 of
the FCC rules.
Notice for Customers in the State of California
WARNIN G: Handling the cord on this
product may expose you to lead, a
chemical known to the State of California to cause birth defects or other
reproductive harm. Wash hands afterhandling.
Nikon Inc., 1300 Walt Whitman Road,
Melville, New York 11747-3064, U.S.A.
Tel.: 631-547-4200
xiii
Notice Concerning Prohibition of Copying or Reproduction
Note that simply being in possession of material that has been digitally copied or reproduced by means of a scanner, digital camera, or other device may
be punishable by law.
• Items prohibited by law from being copied
or reproduced
Do not copy or reproduce paper
money, coins, securities, government bonds, or local government
bonds, even if such copies or reproductions are stamped “Sample.”
The copying or reproduction of
paper money, coins, or securities
which are circulated in a foreign
country is prohibited.
Unless the prior permission of the
government has been obtained, the
copying or reproduction of unused
postage stamps or post cards issued
by the government is prohibited.
The copying or reproduction of
stamps issued by the government
and of certified documents stipulated by law is prohibited.
• Cautions on certain copies and reproduc-
tions
The government has issued cautions
on copies or reproductions of securities issued by private companies
(shares, bills, checks, gift certificates,
etc.), commuter passes, or coupon
tickets, except when a minimum of
necessary copies are to be provided
for business use by a company. Also,
do not copy or reproduce passports
issued by the government, licenses
issued by public agencies and private groups, ID cards, and tickets,
such as passes and meal coupons.
• Comply with copyright notices
The copying or reproduction of
copyrighted creative works such as
books, music, paintings, woodcuts,
prints, maps, drawings, movies, and
photographs is governed by
national and international copyright
laws. Do not use this product for the
purpose of making illegal copies or
to infringe copyright laws.
xiv
Disposing of Data Storage Devices
Please note that deleting images or formatting memory cards or other data
storage devices does not completely erase the original image data. Deleted
files can sometimes be recovered from discarded storage devices using commercially available software, potentially resulting in the malicious use of personal image data. Ensuring the privacy of such data is the user’s responsibility.
Before discarding a data storage device or transferring ownership to another
person, erase all data using commercial deletion software, or format the
device and then completely refill it with images containing no private information (for example, pictures of empty sky). Wi-Fi settings can be reset to
default values by selecting Reset Wi-Fi settings for Wi-Fi connection type in
the Wi-Fi menu (0 117). Care should be taken to avoid injury when physically
destroying data storage devices.
ANDNON-COM MERCIALUSEOFACONSUMERTO (i) ENCODEVIDEOINCOMPLIANCEWITH
THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEOTHATWASENCODED
BYACONSUMERENGAGEDINAPERSONALANDNON-COMMERCIALACTIVITYAND/ORWAS
OBTAINEDFROMAVIDEOPROVIDERLICENSEDTO PROVIDE AVC VIDEO. NOLICENSEIS
GRANTEDORSHALLBEIMPLIEDFORANYOTHERUSE. ADDITIONALINFORMATIONMAYBE
OBTAINEDFROM MPEG LA, L.L. C. SEEhttp://www.mpegla.com
Temperature Warnings
The camera may become warm to the touch during use; this is normal and
does not indicate a malfunction. At high ambient temperatures, after
extended periods of continuous use, or after several photographs have been
taken in quick succession, a temperature warning may be displayed, following which the camera will turn off automatically to minimize damage to its
internal circuits. Wait for the camera to cool before resuming use.
xv
Use Only Nikon Brand Electronic Accessories
Nikon cameras are designed to the highest standards and include complex
electronic circuitry. Only Nikon brand electronic accessories (including chargers, batteries, AC adapters, and lens accessories) certified by Nikon specifically for use with this Nikon digital camera are engineered and proven to
operate within the operational and safety requirements of this electronic circuitry.
The use of non-Nikon electronic accessories could damage the
camera and may void your Nikon warranty. The use of thirdparty rechargeable Li-ion batteries not bearing the Nikon holographic seal shown at right could interfere with normal operation of the camera or result in the batteries overheating, igniting, rupturing, or leaking.
For more information about Nikon brand accessories, contact a local authorized Nikon dealer.
xvi
Use Only Nikon Brand Accessories
D
Only Nikon brand accessories certified by Nikon specifically for use
with your Nikon digital camera are engineered and proven to operate
within its operational and safety requirements. T
ACCESSORIES
RANTY.
D
The camera is a precision device and requires regular servicing. Nikon
recommends that the camera be inspected by the original retailer or a
Nikon-authorized service representative once every one to two years,
and that it be serviced once every three to five years (note that fees
apply to these services). Frequent inspection and servicing are particularly recommended if the camera is used professionally. Any accessories regularly used with the camera, such as lenses, should be included
when the camera is inspected or serviced.
A
Before taking pictures on important occasions (such as at weddings or
before taking the camera on a trip), take a test shot to ensure that the
camera is functioning normally. Nikon will not be held liable for damages or lost profits that may result from product malfunction.
A
As part of Nikon’s “Life-Long Learning” commitment to ongoing product support and education, continually-updated information is available on-line at the following sites:
• For u sers in the U.S. A.: http://www.nikonusa.com/
• For users in Europe and Africa: http://www.europe-nikon.com/support/
• For users in Asia, Oceania, and the Middle East: http://www.nikon-asia.com/
Visit these sites to keep up-to-date with the latest product information, tips, answers to frequently-asked questions (FAQs), and general
advice on digital imaging and photography. Additional information
may be available from the Nikon representative in your area. For contact information, visit http://imaging.nikon.com/
COULDDAMAGEYOURCAMERAANDMAYVOIDYOUR NIKONWAR-
Servicing th e Camera and Accessories
Before Taking Important Pictures
Life-Long Learning
HEUSEOFNON-NIKON
xvii
Wireless
This product, which contains encryption software developed in the United
States, is controlled by the United States Export Administration Regulations
and may not be exported or re-exported to any country to which the United
States embargoes goods. The following countries are currently subject to
embargo: Cuba, Iran, North Korea, Sudan, and Syria.
The use of wireless devices may be prohibited in some countries or regions.
Contact a Nikon-authorized service representative before using the wireless
features of this product outside the country of purchase.
Notices for Customers in the U. S. A.
This device complies with Part 15 of FCC Rules and Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause inter ference, and (2) this device must a ccept any
interference, including interference that may cause undesired operation of
the device.
FCC WARNING
The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by Nikon Corporation
may void the user’s authority to operate the equipment.
FCC Radio Frequency Interference Statement
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Co-location
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
Nikon Inc., 1300 Walt Whitman Road, Melville, New York 11747-3064, U.S.A.
Tel.: 631-547-4200
xviii
Notices for Customers in Canada
This device complies with Part 15 of FCC Rules and Industry Canada licenceexempt RSS standard(s). Operation is subjec t to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of
the device.
FCC/IC RF Exposure Statement
The available scientific evidence does not show that any health problems are
associated with using low power wireless devices. There is no proof, however,
that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave
range while being used. Whereas high levels of RF can produce health effects
(by heating tissue), exposure of low-level RF that does not produce heating
effects causes no known adverse health effects. Many studies of low-level RF
exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not
been confirmed by additional research. The 1 J5, which is equipped with a
DW092 (FCC ID:EW4DW092 / IC ID:4634A-3149EC) wireless LAN module, has
been tested and found to comply with FCC/IC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio frequency
(RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC
radio frequency (RF) Exposure rules. Please refer to the SAR test report that
was uploaded to FCC website.
Notices for Customers in Europe
Hereby, Nikon Corporation, declares that the 1 J5 is in compliance
with the essential requirements and other relevant provisions of
Directive 1999/5/EC. The declaration of conformity may be consulted at http://imaging.nikon.com/support/pdf/DoC_1J5.pdf
Notice for Customers in Singapore
Trade Name:
Model: 1 J5
This device complies with radio-frequency regulations. The content of certification labels not affixed to the device is given below.
Complies w ith
IDA Standards
DA103423
xix
Notice for Customers in Algeria
This device complies with Part 15 of FCC Rules and Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause inter ference, and (2) this device must a ccept any
interference, including interference that may cause undesired operation of
the device.
Co-location
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
FCC/IC RF Exposure Statement
The available scientific evidence does not show that any health problems are
associated with using low power wireless devices. There is no proof, however,
that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave
range while being used. Whereas high levels of RF can produce health effects
(by heating tissue), exposure of low-level RF that does not produce heating
effects causes no known adverse health effects. Many studies of low-level RF
exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not
been confirmed by additional research. The 1 J5, which is equipped with a
DW092 (FCC ID:EW4DW092 / IC ID:4634A-3149EC) wireless LAN module, has
been tested and found to comply with FCC/IC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio frequency
(RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC
radio frequency (RF) Exposure rules. Please refer to the SAR test report that
was uploaded to FCC website.
Security
Although one of the benefits of this product is that it allows others to freely
connect for the wireless exchange of data anywhere within its range, the following may occur if security is not enabled:
• Data theft: Malicious third-parties may intercept wireless transmissions to
steal user IDs, passwords, and other personal information.
• Unauthorized access: Unauthorized users may gain access to the network
and alter data or perform other malicious actions. Note that due the design
of wireless networks, specialized attacks may allow unauthorized access
even when security is enabled.
xx
Introduction
s
Before You Begin
Before using your camera for the first time, confirm that the
package contains the items listed in the User’s Manual.
s
1
Parts of the Camera
Take a few moments to familiarize yourself with camera controls
and displays. You may find it helpful to bookmark this section
and refer to it as you read through the rest of the manual.
The area recorded when electronic vibration
reduction (0 183) is in effect during movie
recording is shown by a frame in the shooting display.
s
5
The Mode Dial
The camera offers a choice of the following shooting modes:
s
CAuto mode (0 33): Let the camera pick the settings for photographs
and movies.
aSports mode (0 74): The camera takes pic-
tures continuously while the shutter-release
button is pressed. Choose for sporting
events and other scenes with fast-moving
subjects.
wCreative mode (0 58): Use special effects or match settings to the
scene.
P Pop
Q Retro
R High-contrast
monochrome
S Nostalgic sepia
5 HDR
q Soft
p Easy panorama
r Miniature effect
s Selective color
6 Cross process
7 Toy c ame ra e ffe ct
T Cross screen
U Fisheye
Mode dial
V Skin softening
j Night landscape
o Night portrait
l Landscape
n Close-up
k Portr ait
6
t, u, v, and w modes (0 67): Control shutter speed and aperture for
advanced photographic effects.
• P: Programmed auto (0 67)
• S: Shutter-priority auto (0 68)
u Best moment capture mode (0 76): Choose
Active Selection to select the best picture
from 20 shots in temporary storage, Slowview to choose the best timing for the shot
while the scene plays back in slow motion,
or Smart Photo Selector to let the camera
pick the best shot based on composition
and movement.
zMotion Snapshot mode (0 88): Each time the
shutter is released, the camera records a still
image and about 1.6 s of movie footage.
When the resulting “Motion Snapshot” is
viewed on the camera, the movie will play
back in slow motion over approximately 4 s,
followed by the still image.
vAdvanced movie mode (0 49): Choose an exposure mode and adjust
shutter-speed or aperture or record movies in slow or fast motion or
with other special effects.
• A: Aperture-priority auto (0 69)
• M: Manual (0 70)
s
7
The Multi Selector
The multi selector and J button are used
to adjust settings and navigate the camera menus.
s
Settings: &
Access the & (feature) menu, a context-sensitive menu listing options for shooting or playback (0 11).
Menu navigation: 1
Move cursor up.
Settings:
C
View continuous
shooting/self-timer
menu (0 74, 97, 99).
Menu navigation: 4
Return to previous
menu.
Settings: M
View flash mode menu (0 102, 104).
Menu navigation: 3
Move cursor down.
The Multi Selector
A
Items can be highlighted by rotating the multi selector
as shown at right.
Multi selector
Select highlighted
item.
Settings: E
View exposure compensation menu
(0 101).
Menu navigation: 2
Select highlighted item
or display sub-menu.
8
The G Button
Most shooting, playback, setup, and Wi-Fi
options can be accessed from the camera
menus. To view the menus, press the
G button.
G button
Tab s
Choose from the following menus:
D Playback menu (0 149)
C w PSAM a v u z Shooting menu (0 158)
B Setup menu (0 193)
v Wi-Fi menu (0 114)
Menu options
Options in current menu.
Slider shows position in
current menu.
Using the Menus
A
The items listed may vary with camera settings. Items displayed in gray
are not currently available. To exit the menus and return to shooting
mode, press the shutter-release button halfway (0 39).
s
9
❚❚ Using the Menus
Use the multi selector (0 8) to navigate
the playback, shooting, setup, and Wi-Fi
menus.
s
Select a menu.
1
Press 1 or 3 to highlight tabs and
press 2 to position the cursor in the
highlighted menu.
Select an item.
2
Press 1 or 3 to highlight menu items
and press 2 to view options for the
highlighted item.
Select an option.
3
Press 1 or 3 to highlight the desired option and press J to
select.
Touch Controls
A
Slide up or down to scroll and tap menu
items or icons to select options or adjust settings (0 19).
Multi selector
10
The & (Feature) Menu
To display the feature menu and adjust
camera settings or access playback
options, press & (feature) on the multi
selector.
& menu (shooting mode)& menu (playback)
Select an item.
1
Use the multi selector to highlight an
item and press J to display options
(to exit the & menu, press the shutterrelease button halfway as described
on page 39 or highlight 1 and press
J).
Select an option.
2
Highlight the desired option or value and press J to select.
s
11
The & Menu
A
The & menu is context-sensitive: its contents vary with camera settings or the type of image displayed; options that are currently unavailable are shown in gray. The & menu is not available in auto or sports
mode.
& Menu Touch Controls
A
Items in the & menu can also be selected by
tapping the monitor.
s
12
The Function (Fn) Button
The Fn button can be used for quick recall
of frequently-used settings during shooting. To choose the role played by the Fn
button, select Assign Fn button in the
setup menu (0 193) and choose from the
following options:
• Exposure compensation
(0 101)
• Metering (0 166)
• White balance (0 167)
• ISO sensitivity (0 172)
• Picture Control (0 173)
• AF-area mode (0 188)
• Focus mode (0 184)
Fn button
s
13
Tilting the Monitor
The monitor can be angled and rotated as shown below.
Normal use: The monitor is normally used in
storage position.
s
Low-angle shots: Tilt the monitor up to frame shots with the camera close
to the ground. Once in the low-angle position, the monitor can be further lowered.
High-angle shots: Tilt the monitor down to frame shots while holding the
camera over your head.
14
Self-portraits (0 108): Reverse the monitor to select self-portrait mode.
Using the Monitor
D
Rotate the monitor gently within the limits of the hinges. Do not use
force. Failure to observe these precautions could damage the camera
or monitor. If the camera is mounted on a tripod, care should be taken
to ensure that the monitor does not contact the tripod.
Do not touch the area to the rear of the
monitor. Failure to observe this precaution
could cause product malfunction.
s
Be particularly careful
not to touch these
areas.
15
Using the Touch Screen
The touch-sensitive monitor supports the following operations:
Tap
Tap the moni tor.
s
Flick
Flick a finger a short distance across the
monitor.
Slide
Slide a finger over the monitor.
Stretch/Pinch
Place two fingers on the monitor and
move them apart or pinch them together.
16
The Touch Screen
D
The touch screen responds to static electricity and may not respond
when covered with third-party protective films or when touched with
fingernails or gloved hands. Do not use excessive force or touch the
screen with sharp objects.
Using the Touch Screen
D
The touch screen may not respond as expected if you attempt to operate it while leaving your palm or another finger resting on it in second
location. It may not recognize other gestures if your touch is too soft,
your fingers are moved too quickly or too short a distance or do not
remain in contact with the screen, or if the movement of the two fingers in a pinch or stretch is not correctly coordinated.
Enabling or Disabling Touch-screen Controls
A
Touch controls can be enabled or disabled using the Tou c h- s cr e en
controls option in the setup menu (0 194).
❚❚ Taking Pictures
The touch screen can be used for the following shooting operations.
s
Take a
picture (tap
shooting)
Focus (tap
shooting)
In auto, creative, P, S, A, M, and self-
portrait modes, you can focus and
take a picture by tapping your
subject in the display.
In advanced movie mode, you
can focus by tapping your subject
in the display.
17
Tap highlighted icons to view settings and tap icons or sliders to
Adjust
settings
s
Tap Shooting Options
A
Tap shooting options can be
adjusted by tapping the icon
shown at right (0 111).
change (the items available vary
with camera settings). Tap 0 to
save changes and exit, or tap 2 to
exit to the previous display without saving changes.
❚❚ Viewing Pictures
The touch screen can be used for the following playback operations.
18
View other
images
View movies
or panoramas
Flick left or right to view other
images.
Tap the on-screen guide to start
movie or panorama playback
(movies are indicated by a 1
icon). Tap the display to pause or
resume.
Guide
Zoom in
View
thumbnails
Use stretch and pinch gestures to
zoom in and out and slide to
scroll. You can also double-tap a
picture in full-frame playback to
zoom in and double-tap again to
exit zoom (0 131).
To “zoom out” to a thumbnail
view (0 129), use a pinch gesture
in full-frame playback. Use pinch
and stretch to choose the number
of images displayed from 4, 9, or
16 frames.
s
View other
months
Use
on-screen
guides
Flick left or right to view other
months in the calendar display
(0 130).
Various operations can be performed by tapping on-screen
guides.
❚❚ Using the Menus
The touch screen can be used for the following menu operations.
ScrollSlide up or down to scroll.
19
Choose a
menu
Tap a menu icon to choose a
menu.
s
Select items/
adjust
settings
❚❚ The & Menu
The touch screen can be used to adjust settings in the & menu.
Select items/
adjust
settings
Tap menu items to display
options and tap icons or sliders to
change. Tap 2 to exit to the previous display without changing settings.
Tap menu items to display
options and tap icons or sliders to
change. Tap 0 to save changes
and exit, or tap 2 to exit to the
previous display without changing settings.
20
First Steps
Battery
charging
Charging
complete
Attach the camera strap.
1
Attach the strap securely to the two camera eyelets.
Charge the battery.
2
Insert the battery into the charger q and plug the charger in
w. An exhausted battery fully charges in about two hours and
30 minutes. Unplug the charger and remove the battery
when charging is complete.
The Plug Adapter
A
Depending on the country or region of
purchase, a plug adapter may be supplied with the charger. The shape of the
adapter varies with the country or region
of purchase. If a plug adapter is supplied,
raise the wall plug and connect the plug
adapter as shown at right, making sure
the plug is fully inserted. Attempting to forcibly remove the plug
adapter could damage the product.
s
21
s
The Battery and Charger
D
Read and follow the warnings and cautions on pages ix–xi and 207–
210 of this manual. Do not use the battery at ambient temperatures
below 0°C (32 °F) or above 40°C (104°F); failure to observe this precaution could damage the battery or impair its performance.
Capacity may be reduced and charging times may increase at battery temperatures from 0°C (32 °F) to 10 °C (50°F) and from 45°C
(113°F) to 60 °C (140 °F); the battery will not charge if its temperature is below 0°C (32 °F) or above 60°C (140°F).
Charge the battery at ambient temperatures between 5 °C (41 °F)
and 35°C (95°F). If the CHARGE lamp flashes quickly during charging,
cease use immediately and take battery and charger to your retailer
or a Nikon-authorized service representative.
Do not move the charger or touch the battery during charging. Failure to observe this precaution could in very rare instances result in
the charger showing that charging is complete when the battery is
only partially charged. Remove and reinsert the battery to begin
charging again.
Use the charger with compatible batteries only. Unplug when not
in use.
22
Insert the battery and a memory card.
16GB
Front
3
The camera stores pictures on microSD, microSDHC, and
microSDXC memory cards (available separately; 0 203).
Before inserting the battery or memory cards, check that they
are in the correct orientation. Using the battery to keep the
orange battery latch pressed to one side, slide the battery in
until it latches, and then slide in the memory card until it
clicks into place. Do not attempt to insert the card at an angle;
failure to observe this precaution could damage the product.
s
23
s
Inserting and Removing Batteries and Memory Cards
D
Always turn the camera off before inserting or removing batteries
or memory cards. Note that the battery and memory cards may be
hot after use; observe due caution when removing the battery and
memory cards.
Formatting Memory Cards
A
If this is the first time the memory card
will be used in the camera or if the card
has been formatted in another device,
select Format memory card in the setup
menu and follow the on-screen instructions to format the card (0 195). Note
that this permanently deletes any data the
card may contain. Be sure to copy any photographs and other data
you wish to keep to a computer before proceeding (0 140).
24
Removing Batteries and Memory Cards
A
After turning the camera off, confirm that
the memory card access lamp (
and open the battery-chamber/memory
card slot cover. To remove the battery,
first release it by pressing the orange battery latch in the direction shown by the
arrow and then remove the battery by
hand.
To remove a memory card, first press the
card in to eject it (q); the card can then
be removed by hand (w).
taken to prevent the card popping from
the camera when ejected.
Memory Cards
D
• Do not remove memory cards from the camera, turn the camera
off, or remove or disconnect the power source during formatting
or while data are being recorded, deleted, or copied to a computer. Failure to observe these precautions could result in loss of
data or in damage to the camera or card.
• Do not touch the card terminals with your fingers or metal
objects.
• Do not bend, drop, or subject to strong physical shocks.
• Do not apply force to the card casing. Failure to observe this pre-
caution could damage the card.
• Do not expose to water, heat, high levels of humidity, or direct
sunlight.
• Do not format memory cards in a computer.
0
3) is off
Care should be
s
25
s
Remove the
rear lens cap
Remove the camera body cap
Mounting mark (camera)
Mounting mark (lens)
Keeping the mounting marks
aligned, position the lens on
the camera
Attach a lens.
4
Be careful to prevent dust from entering the camera when the
lens or body cap is removed. The lens generally used in this
manual for illustrative purposes is a 1 NIKKOR VR 10–30mm
f/3.5–5.6 PD-ZOOM.
26
Rotate the lens as shown until it clicks into place.
Zoom ring
Retractable lens barrel
button
If the lens supports vibration reduction (VR), vibration reduction can be controlled from the camera (0 183).
Detaching the Lens
A
Be sure the lens is retracted before
removal. To remove the lens, turn the
camera off, then press and hold the lens
release button (q) while turning the lens
clockwise (w). After removing the lens,
replace the camera body cap, the rear
lens cap, and, if applicable, the front lens
cap.
Lenses with Retractable Lens Barrel Buttons
A
Lenses with retractable lens barrel buttons can not be used when retracted. To
unlock and extend the lens, readying the
camera for use, keep the retractable lens
barrel button pressed (q) while rotating
the zoom ring as shown (w). The lens can
be retracted and the zoom ring locked by
pressing the button and rotating the ring
in the opposite direction. Be careful not
to press the retractable lens barrel button
while attaching or removing the lens.
s
27
s
Turn the camera on.
5
Rotate the power switch to turn the
camera on. The power lamp will
briefly light green and the monitor will
turn on. If the lens is equipped with a
front lens cap, remove the cap before
shooting. If a 1 NIKKOR VR 10–30mm
f/3.5–5.6 PD-ZOOM lens is attached,
the lens will automatically extend
when the camera is turned on and
retract when the camera is turned off.
Turning the Camera Off
A
To turn the camera off, rotate the power switch again. The monitor
will turn off.
Auto Power Off
A
If no operations are performed for about a minute, the display will
turn off and the power lamp will start to flash (if desired, the delay
before the display turns off automatically can be changed using the
Auto power off option in the setup menu; 0 197). The camera can
be reactivated by operating the shutter-release button. If no operations are performed for about three minutes after the display has
turned off, the camera will turn off automatically.
Attaching and Removing Lenses
A
Turn the camera off before attaching or removing lenses. Note that
when the camera is turned off, the sensor protection barrier in the
lens will close, protecting the camera image sensor.
28
Lenses with Retractable Lens Barrel Buttons
A
The camera will turn on automatically when the retractable lens
barrel lock is released; in addition, if the view through the lens is
displayed or the monitor is off, the camera will turn off when the
lens barrel is locked (in the case of 1 NIKKOR VR 10–30mm f/3.5–5.6
and 1 NIKKOR VR 30–110mm f/3.8–5.6 lenses, fir mware version 1.10
or later is required if locking the lens barrel is to turn the camera off
when the monitor is off; for information on updating lens firmware,
visit the Nikon website for your area).
Choose a language.
6
A language-selection dialog will be
displayed the first time the camera is
turned on. Use the multi selector and
J button (0 8) to choose a language.
s
29
s
Set the clock.
7
Use the multi selector and J button
(0 8) to set the time and date. Note
that the camera uses a 24-hour clock.
30
Press 4 or 2 to highlight time
zone and press J.
Press 1 or 3 to highlight daylight
saving time option and press J.
Note: Language and clock can be changed at any time using Language
(0 194) and Time zo ne and date (0 199) options in setup menu.
Press 1 or 3 to highlight date
format and press J.
Press 4 or 2 to highlight items
and press 1 or 3 to change. Press
J to exit to shooting display when
setup is complete.
The Camera Clock
A
The camera clock is less accurate than most watches and household clocks. Check the clock regularly against more accurate time
pieces and reset as necessary.
The camera clock is powered by an independent, rechargeable
power source, which is charged as necessary when the main battery is installed or the camera is powered by an optional power
connector and AC adapter (0 204). Three days of charging will
power the clock for about a month. If a message warning that the
clock is not set is displayed when the camera is turned on, the clock
battery is exhausted and the clock has been reset. Set the clock to
the correct time and date.
s
31
s
Battery level
Exposures remaining
Check the battery level and memory card capacity.
8
Check the battery level and number
of exposures remaining in the monitor.
❚❚ Battery Level
DisplayDescription
Battery fully charged or
NO ICON
H
Cannot take pictures.
Insert fully-charged
battery.
partially discharged;
level shown by L or
K icon in detailed
display (0 196).
Low battery. Ready
fully-charged battery or
prepare to charge
battery.
Battery exhausted;
shutter-release
disabled. Insert charged
battery.
❚❚ Number of Exposures Remaining
The monitor shows the number of pictures that can be stored
on the memory card at current settings (values over 1000 are
rounded down to the nearest hundred; e.g., values between
1200 and 1299 are shown as 1.2 k). If a warning is displayed
stating that there is not enough memory for additional
images, insert another memory card (0 23) or delete some
photos (0 134).
32
Taking and Viewing Photographs
z
This chapter describes how to take, view, and delete photographs in auto and creative mode.
Point-and-Shoot Photography (Auto Mode)
Follow the steps below to take photographs in auto mode, a
“point-and-shoot” mode in which the camera automatically
detects the subject type and adjusts settings according to the
subject and situation.
Turn the camera on.
1
Rotate the power switch to turn the
camera on.
Select C mode.
2
Rotate the mode dial to C (auto).
z
33
z
Focus are a
34
Ready the camera.
3
Hold the camera securely with both
hands, being careful not to obstruct
the lens, AF-assist illuminator, or
microphone. Rotate the camera as
shown at lower right when taking pictures in “tall” (portrait) orientation.
Shutter speeds slow when lighting is
poor; use of the built-in flash (0 102)
or a tripod is recommended.
Frame the photograph.
4
Position your subject in the center of
the frame. At default settings, the
camera will automatically detect portrait subjects and position the focus
point accordingly (0 40).
Focus.
5
Press the shutter-release
button halfway to focus. If
the subject is poorly lit, the
flash may pop up (0 102)
and the AF-assist illuminator (0 191) may light to
assist the focus operation.
If the camera is able to focus, the selected
focus area will be highlighted in green
and a beep will sound (a beep may not
sound if the subject is moving).
If the camera is unable to focus, the focus
area will be displayed in red.
Shoot.
6
Smoothly press the shutterrelease button the rest of
the way down to release
the shutter and record the
photograph.
Pictures can also be taken
using touch controls. Tap a
subject anywhere in the
frame to focus and release
the shutter.
After the shutter is
released, the memory card
access lamp will light and
the photograph will be displayed in the monitor for a
few seconds (the photo will
automatically clear from
the display when the shutter-release button is
pressed halfway). Do not
eject the memory card or
remove the battery until the
lamp has gone out and
recording is complete.
z
Memory card access lamp
35
The Framing Grid
A
A framing grid can be displayed by selecting
On for Display > Grid display in the setup
menu (0 196).
See Also
A
See page 197 for information on silencing the beep that sounds when
the camera focuses or the shutter is released.
z
36
Viewing Photographs
Press K to display your most recent photograph full frame in the monitor (fullframe playback).
K button
Press 4 or 2 or rotate the multi selector
to view additional pictures. You can also
scroll through pictures by flicking left or
right (0 18).
To zoom in on the center of the current
image, rotate the command dial to the
right (0 131). Rotate left to zoom out
(you can also zoom in or out using touch
controls: place two fingers on the monitor and spread them apart to zoom in or
pinch them together to zoom out). To
view multiple images, rotate the dial left
when the picture is displayed full frame
(0 129).
To end playback and return to shooting mode, press the shutterrelease button halfway.
Command dial
z
37
Deleting Pictures
To delete the current picture, press O. Note that once deleted, pictures can not be recovered.
Display the photograph.
1
Display the photograph you wish to delete as described on
the preceding page.
Press O.
2
z
A confirmation dialog will be displayed.
Delete the photograph.
3
Press O again to delete the picture and
return to playback, or press K to exit
without deleting the picture.
O button
38
The Shutter-Release Button
A
The camera has a two-stage shutter-release button. The camera
focuses when the shutter-release button is pressed halfway. To take
the photograph, press the shutter-release button the rest of the way
down.
Focus: Press halfwayShoot: Press the rest
Taking Several Photographs in Succession
A
You can take additional photographs without refocusing by keeping
the shutter-release button pressed halfway between shots.
Automatic Scene Selection
A
In auto mode, the camera automatically analyzes the subject and selects the appropriate
scene. The selected scene is shown in the
monitor.
Portr ait: Human portrait subjects.
c
Landscape: Landscapes and cityscapes.
d
Night portrait: Portrait subjects framed against dark backgrounds.
f
Close-up: Subjects close to the camera.
e
Night landscape: Poorly-lit landscapes and cityscapes.
g
Auto: Subjects that do not fall into the categories listed above.
Z
of the way down
Scene icon
z
39
Using a Zoom Lens
A
Use the zoom ring to zoom in on the subject so that it fills a larger area
of the frame, or zoom out to increase the area visible in the final photograph. During movie recording with the 1 NIKKOR VR 10–30mm f/3.5–
5.6 PD-ZOOM, the zoom rate is unaffected by the speed with which the
ring is rotated.
Zoom in
Zoom out
z
Zoom ring
If you are using a 1 NIKKOR VR 10–100mm
f/4.5–5.6 PD-ZOOM lens (available separately), slide the power drive zoom switch to
T to zoom in and to W to zoom out. The
speed with which the camera zooms in and
out varies with how far you slide the switch.
The zoom position is shown by the zoom
guide in the display.
Face Pri ority
A
The camera detects and focuses on portrait
subjects (face priority). A double yellow border will be displayed if a portrait subject is
detected facing the camera (if multiple
faces, up to a maximum of five, are detected,
the camera will select the closest subject).
Press the shutter-release button halfway to
focus on the subject in the double yellow border. The border will clear
from the display if the camera can no longer detect the subject
(because, for example, the subject has looked away).
Zoom guide
40
Deleting Multiple Pictures
A
The Delete option in the playback menu (0 134) can be used to de lete
all or selected pictures.
See Also
A
For information on toggling photo info on or off, see page 196.
z
41
Recording and Viewing Movies
y
Recording Movies
Turn the camera on.
1
Rotate the power switch to turn the
camera on.
y
42
Choose a shooting mode.
2
Rotate the mode dial to any of the
positions shown at right.
Frame the opening shot.
3
Frame the opening shot with your
subject in the center of the display.
The 0 Icon
A
A 0 icon indicates that movies can not be recorded.
Start recording.
4
Press the movie-record button to
begin recording. A recording indicator, the time elapsed, and the time
available are displayed while recording is in progress.
Audio Recording
A
Be careful not to cover the microphone
and note that the built-in microphone
may record sounds made by the camera
or lens. Except when recording timelapse or slow-motion movies in advanced
movie mode, the camera focuses continuously; to avoid recording focus noise,
select
Single AF
movie menu (
End recording.
5
0
184).
for
Focus mode
in the
Movie-record button
Recording indicator/
Time elapsed
Time available
Press the movie-record button again
to end recording. Recording will end
automatically when the maximum
length is reached (0 165), the memory card is full, another mode is
selected, the lens is removed, or the
camera becomes hot (0 xv).
Maximum Length
A
The camera can record movies up to 4 GB in size (for more information, see page 165); note that depending on memory card write
speed, shooting may end before this length is reached (0 203).
Movie-record button
y
43
❚❚ Choosing a Shooting Mode
The features available in each mode are listed below.
Choose this mode to record HD movies
Auto mode (0 33)
C
Creative mode (0 58)
w
y
Sports mode (0 74)
a
P S
P, S, A, and M modes
(0 67)
A M
Advanced movie mode
v
(0 49)
Movie Sound
A
The Movie sound options item in the movie menu offers microphone
sensitivity and wind noise options (0 180).
while leaving the camera in charge of
choosing settings. The camera automatically adjusts settings according to the subject and situation.
Record HD movies with the selected effect.
Note, however, that the selected effect is
not applied in the cases of 5 HDR, q Soft,
p Easy panorama, r Miniature effect,
7 Toy c ame r a ef fec t , T Cross screen, and
V Skin softening.
Record HD movies in exposure mode P.
Choose an exposure mode (0 161) and
record HD movies at a selected shutter
speed or aperture, or record movies in slow
or fast motion or with other special effects.
44
Taking Photographs During Movie Recording
Press the shutter-release button all the
way down to take a photograph without
interrupting movie recording. Photographs taken during movie recording
have an aspect ratio of 3 : 2.
Taking Photographs During Movie Recording
A
Up to 20 photographs can be taken with each movie shot. Please note
that photographs can not be taken with slow-motion, 4K, or timelapse movies in advanced movie mode.
Focus L ock
A
If Single AF is selected for Focus mode in the shooting menu for
advanced movie mode (0 184), focus will lock while the shutterrelease button is pressed halfway (0 189). Note that focus lock is not
available when h Scene auto selector is selected for Exposuremode in the shooting menu (0 161).
See Also
A
See page 180 for information on configuring the camera to take photographs automatically during movie recording.
y
45
Viewing Movies
Movies are indicated by a 1 icon in full-frame playback (0 37).
Press the J button or tap the M icon to start playback.
1 icon/LengthCurrent position/total length
y
M iconVolumeGuide
The following operations can be performed:
ToUseDescription
Pause playback; the
Pause
Play
Advance/
rewind
Adjust
volume
Return to
full-frame
playback
current position is
shown at the top of
the display. Playback can also be paused by
tapping the monitor.
Resume playback when the movie is paused
J
or during rewind/advance.
Press 4 to rewind, 2 to advance. Speed
increases with each press, from 2× to 4× to 8×
to 16×. If playback is paused, the movie
rewinds or advances one frame at a time; keep
the button pressed for continuous rewind or
advance.
Rotate the command dial to adjust volume.
Press 1 or K to exit to full-frame playback.
/K
46
Deleting Movies
O button
To delete the current movie, press O. A
confirmation dialog will be displayed;
press O again to delete the movie and
return to playback, or press K to exit
without deleting the movie. Note thatonce deleted, movies can not be recovered.
y
47
See Also
A
See page 156 for information on trimming unwanted footage from
movies. For information on the frame size and frame rate options available for HD movies, see page 165.
Recording Movies
D
Flicker, banding, or distortion may be visible in the display and in the
final movie under fluorescent, mercury vapor, or sodium lamps or with
subjects that are in motion, particularly if the camera is panned horizontally or an objects moves horizontally at high speed through frame
(flicker and banding can be reduced by choosing a Flicker reduction
option that matches the frequency of the local AC power supply as
described on page 198, but note that the slowest shutter speed avail-
y
1
able is
/
100 s at 50 Hz,
with slow-motion movies). Bright light sources may leave after-images
when the camera is panned. Jagged edges, color fringing, moiré, and
bright spots may also appear. When recording movies, avoid pointing
the camera at the sun or other strong light sources. Failure to observe
this precaution could result in damage to the camera’s internal circuitry.
1
/
60 s at 60 Hz; flicker reduction is not available
48
v Advanced Movie Options
Recording
Playback
Approx. 25 min
Approx. 10 s
Recording
Playback
Approx. 40 s
Approx. 3 s
Advanced movie mode can be used not
only to shoot HD movies, but also to
record movies with a variety of effects.
The following options can be accessed by
pressing & and selecting Advance dmovie in the & (feature) menu.
y
HD movie
0
4K movie
z
Time-lapse
8
movie
Slow motion
y
Record HD movies in the exposure mode of your
choice (0 161).
Record movies at a frame size of 3840 × 2160 pixels
and a frame rate of 15 fps.
The camera automatically takes photographs at
selected intervals and joins them together in a silent
time-lapse movie.
Record up to about three seconds of silent slowmotion footage. Slow-motion movies are recorded at
400 fps and play back at about 30 fps.
49
Record silent fast-motion footage that plays back at
Recording
Playback
Approx. 20 min
Approx. 5 min
Recording
Playback
Approx. 20 min
Approx. 10 min
about four times normal speed. Playback time is one
quarter the recording time.
Fast m otion
1
Record silent jump-cut movies. Recording pauses
every other second for a drop-frame effect.
Jump cut
2
y
4-second
3
movie
Adjusting Focus During Recording
A
To change focus during recording, tap the
desired subject in the display. The camera
will display the new focus area and adjust
focus.
4K Movies
A
4K movies can be viewed on a computer and edited using ViewNX-i,
the latest version of which is available for download from the website
listed below. Note that a high-performance system is required; for
information, see the website below.
http://downloadcenter.nikonimglib.com/
When the camera is connected to a 4K-movie compatible television
using an HDMI cable, 4K movies will play back in Full HD (1920 ×
1080 pixels, 30p). Even if the television is 4K-movie compatible, 4K
movies can not be viewed by inserting the camera memory card in a
television microSD card slot.
50
Record a 4-second movie clip.
The & (Feature) Menu (0 11)
A
Pressing & in advanced movie mode displays the items listed below.
The items available vary with the type of movie selected (0 49).
12
6
Recording Time
A
The following table lists the approximate maximum recording times
for individual movies shot at the default frame rate in each shooting
mode.
Auto, creative, P, S, A, M, spor ts modes17 minutes
Advanced movie mode
HD movie17 minutes
4K movie10 minutes
Time-lapse movie25 minutes
Slow motion3 seconds
Fast m otion20 minutes (0 50)
Jump cut20 minutes (0 50)
4-second movie4 seconds
When Time-lapse movie is selected in v (advanced movie)
mode, the camera automatically takes photos at selected intervals to create a silent time-lapse movie.
Select advanced movie mode.
1
Rotate the mode dial to v.
y
Select Time-lapse movie.
2
Press & (feature) on the multi selector
to display the & menu. Highlight
Advanced movie and press J to dis-
play advanced movie options, then
highlight Time-lapse movie and
press J.
Choose the interval between shots.
3
Highlight Interval in the & menu and
press J, then highlight the desired
interval and press J.
52
Enable or disable exposure lock.
4
Highlight AE lock in the & menu and
press J to display the following exposure lock options. Highlight the
desired option and press J.
• AE-L (On): Exposure for the time-lapse
movie is locked at the value metered
at the start of recording.
• OFF: Exposure is metered separately
for each frame.
Focus.
5
Press the shutter-release button halfway to focus.
Start filming.
6
Press the movie-record button to start
filming. The camera will take photographs at the interval selected in Step
3. All controls except the power switch
and the J button are disabled during
filming.
End filming.
7
Press the J button to end filming and
record the movie to the memory card
(if the button is not pressed, recording
will end automatically after 300 shots).
y
Movie-record button
53
Time-Lapse Movies
A
Use of a tripod is recommended. To ensure that shooting is not interrupted, use an optional AC adapter and power connector or charge the
battery before recording. The camera will not turn off automatically
during recording (0 28), but if the interval between shots is 30 s when
the camera is operating on battery power, the monitor will turn off and
the power lamp will flash green.
For consistent coloration, choose a white balance setting other than
v (auto, 0 167).
Time-lapse movies are recorded at a frame size of 1920 × 1080 pixels
and play back at 30 fps. If recording ends before 30 frames have been
recorded, the final frame will be copied as necessary to create a movie
y
1 second long.
54
Filming Slow-Motion Movies
Silent slow-motion movies with an aspect ratio of 8 : 3 can be
recorded by selecting Slow motion in v (advanced movie)
mode. Slow-motion movies are recorded at 400 fps and play
back at about 30 fps.
Select advanced movie mode.
1
Rotate the mode dial to v.
Select Slow motion.
2
Press & (feature) on the multi selector
to display the & menu. Highlight
Advanced movie and press J to dis-
play advanced movie options, then
highlight Slow motion and press J.
Frame the opening shot.
3
Frame the opening shot with your
subject in the center of the display.
y
55
y
Focus.
4
Press the shutter-release button halfway to focus.
Start filming.
5
Press the movie-record button to
begin filming. A recording indicator,
the time elapsed, and the time available are displayed while recording is
in progress. The camera focuses on
the subject at the center of the display; face detection (0 40) is not available and focus and exposure can not
be adjusted.
End filming.
6
Press the movie-record button again
to end filming. Filming will end automatically after 3 seconds or when the
memory card is full.
Movie-record button
Recording indicator/
time elapsed
Time available
56
Movie-record button
Frame Rate and Playback Length
A
The frame rate for slow-motion movies can be selected using the Slow
motion option in the & menu; the faster the frame rate, the smaller the
1 All figures are approximate.
2 Slow-motion movies will play back over a period of about 4 (120 fps), 13
Frame size
(pixels)
(400 fps), or 40 (1200 fps) times the recording time.
Bit rate
Maximum length
1
(shooting)
3 seconds
1
Maximum length
(playback)
12 seconds
1, 2
y
57
Other Shooting Modes
R
The camera offers a choice of modes that can be used to match
settings to the subject or situation, take photos using special
effects, control shutter speed and aperture, help with hard-totime shots, or combine photos with brief movie vignettes.
w Choosing a Creative Mode
Choose creative mode to match settings to the subject or situation or take photos using special effects.
Select w mode.
1
R
Rotate the mode dial to w (creative).
Choose an option.
2
Press & (feature) on the multi selector
to display the & menu, then highlight
Creative and press J. Highlight an
option suited to your subject and creative intent (0 59) and press J.
58
Choosing a Mode That Matches the Subject or Situation
Choose a creative mode according to the subject or situation:
Choose for a faded, retro effect. Use the & (feature)
menu (0 61) to choose a hue from red and yellow.
Shoot in high-contrast black-and-white.
Shoot in sepia for an antique look.
Shoot photographs with a soft filter effect. Use the &
menu to select the amount of softening and to
choose how softening applies when a portrait subject is detected:
• Filter strength: Choose from I (high), J (normal),
and K (low).
• Por trait: If L is selected and the camera detects
portrait subjects (up to three), softening will be
adjusted to make them stand out. If M is
selected, softening will be applied equally to the
portrait subject and the background.
Shoot panoramas for later viewing on the camera
(0 63).
The top and bottom of each photo is blurred so that
the subject appears to have been a diorama photographed at short range. Works best when shooting
from a high vantage point.
Take photos in which only a selected hue appears in
color (0 66).
Choose a base color to create photographs with different hues. Use the & menu to choose a base color
from red, green, blue, and yellow.
R
59
OptionDescription
Alter color saturation and reduce peripheral illumination for a toy camera effect. The following options
Toy camera effect (7)
Cross screen (T)Add starburst effects to light sources.
Fisheye (U)
R
Skin softening (V)
Night landscape (j) Capture poorly-lit landscapes and cityscapes.
Night portrait (o)
Landscape (l)Choose for vibrant landscapes and cityscapes.
Close-up (n)
Portr ait (k)Use for portraits with soft, natural-looking skin tones.
are available in the & menu (0 61):
• Saturation: Choose from H (high), I (normal), and
J (low).
• Vignet ting: Choose the amount of vignetting from
U (high), V (normal), and W (low).
Create the effect of a fisheye lens. The following
option is available in the & menu:
• Filter strength: The level of the fisheye effect. Choose
from p (high), q (normal), and r (low).
Soften the look of skin for up to three portrait subjects at a time. The amount of softening can be
selected using the
menu; choose from P (high), Q (normal), and R (low).
Choose for portraits taken against a poorly-lit backdrop.
Use for close-up shots of flowers, insects, and other
small objects.
Filter strength
option in the
&
60
The & (Feature) Menu (0 11)
12
3
4
5
6
A
Pressing & in creative mode displays the items listed below. The items
available vary with the option selected for creative mode (0 59).
Details in highlights and shadows are preserved using HDR (high
dynamic range). Each time the shutter-release button is fully
pressed, the camera takes two shots in quick succession and
combines them to preserve details in highlights and shadows in
high-contrast scenes; the built-in flash does not fire. Some time
may be required to process the pictures; the final photograph
will be displayed when processing is complete.
+
R
62
First expos ure
(darker)
Framing HDR Photographs
D
The edges of the image will be cropped out. The desired results may
not be achieved if the camera or subject moves during shooting.
Depending on the scene, shading may be uneven and shadows may
appear around bright objects or halos around dark objects.
Second exposure
(brighter)
Combined HDR
image
Easy Panorama
Follow the steps below to shoot panoramas. During shooting,
the camera focuses using auto-area AF (0 188); face detection
(0 40) is not available. Exposure compensation (0 101) can be
used, but the built-in flash will not fire.
Set focus and exposure.
1
Frame the start of the panorama and press the shutter-release button halfway.
Guides will appear in the
display.
Start shooting.
2
Press the shutter-release
button the rest of the way
down and then lift your finger from the button. 1, 3,4, and 2 icons will appear
in the display to indicate
the possible pan directions.
Pan the camera.
3
Slowly pan the camera up, down, left,
or right as shown below. Shooting will
start when the camera detects the pan
direction and a progress indicator will
appear in the display. Shooting ends
automatically when the end of the
panorama is reached.
Progress indicator
R
63
An example of how to pan the camera is shown below. Without changing your position, pan the camera in a steady curve
either horizontally or vertically. Time the pan according to the
option selected for Image size in the shooting menu: about
15 seconds are needed to complete the pan when
A Normal panorama is selected, about 30 seconds when
B Wide panorama is selected.
R
Panoram as
A
High-distortion wide-angle lenses may fail to produce the desired
results. An error message will be displayed if the camera is panned too
quickly or unsteadily. Note that because panoramas are composed of
multiple images, the joins between images may be visible and the
desired results may not be achieved with moving subjects or with
neon lights or other subjects that exhibit rapid changes in color or
brightness, subjects that are too close to the camera, poorly-lit subjects, and subjects such as the sky or sea that are a solid color or contain simple repeating patterns.
The completed panorama will be slightly smaller than the area visible
in the display during shooting. No panorama will be recorded if shooting ends before the halfway point; if shooting ends after the halfway
point but before the panorama is complete, the unrecorded portion
will be shown in gray.
64
❚❚ Viewing Panoramas
Panoramas can be viewed by pressing J when a panorama is
displayed full frame (0 37). The start of the panorama will be
displayed with the smallest dimension filling the display and the
camera will then scroll through the picture in the original pan
direction.
Guide
The following operations can be performed:
ToUseDescription
Pause playback. A
Pause
Play
Advance/
rewind
Return to
full-frame
playback
navigation window
will appear at the
bottom of the display.
Resume playback when the panorama is
J
paused or during rewind/advance.
Press 4 to rewind, 2 to advance. If playback is
paused, the panorama rewinds or advances a
segment at a time; keep the button pressed
for continuous rewind or advance.
Press 1 or K to exit to full-frame playback.
/K
R
65
Selective Color
Take black-and-white pictures in which one hue appears in a
color.
Choose Select color.
1
Press & to display the & (feature)
menu, then highlight Select color
and press J.
Choose a color.
2
Use the multi selector to choose a
R
color and press J.
Tak e pi ctu res.
3
Press the shutter-release button all the way down to take pictures. Only the selected hue will appear in color; all other
hues will be recorded in shades of gray.
66
Taking Photos in P, S, A, and M Modes
Command dial
P, S, A, and M modes offer varying degrees of
control over shutter speed and aperture.
Choose a mode and adjust settings according
to your creative intent.
P Programmed Auto
In this mode, the camera automatically adjusts shutter speed
and aperture for optimal exposure in most situations. This mode
is recommended for snapshots and other situations in which
you want to leave the camera in charge of shutter speed and
aperture.
Choosing a Combination of Shutter Speed and Aperture
A
Although the shutter speed and aperture
chosen by the camera will produce optimal
results, you can also choose from other combinations that will produce the same exposure (“flexible program”). Rotate the
command dial to the right for large apertures (low f-numbers) that blur background
details or fast shutter speeds that “freeze”
motion. Rotate the dial to the left for small
apertures (high f-numbers) that increase
depth of field or slow shutter speeds that
blur motion. U is displayed while flexible
program is in effect.
R
Restoring Default Shutter Speed and Aper ture Settings
A
To restore default shutter speed and aperture settings, rotate the command dial until U is no longer displayed or turn the camera off. The
default shutter speed and aperture is automatically restored when the
camera enters standby mode.
67
S Shutter-Priority Auto
Command dial
In shutter-priority auto, you choose the shutter speed while the
camera automatically selects the aperture that will produce the
optimal exposure. Use slow shutter speeds to suggest motion by
blurring moving subjects, fast shutter speeds to “freeze” motion.
Fast shutter speed (
1
/
160 0 s)Slow shutter speed (1 s)
❚❚ Choosing a Shutter Speed
Rotate the command dial to choose from
R
shutter speeds between 30 s and
Rotate the dial to the right for faster shutter speeds, to the left for slower shutter
speeds.
Continuous Shooting
A
The selected shutter speed may change
when a frame rate of 10 fps or faster is
selected in continuous shooting mode
(0 97).
68
1
/
16,000 s.
A Aperture-Priority Auto
In aperture-priority auto, you choose the aperture while the
camera automatically selects the shutter speed that will produce
the optimal exposure. Large apertures (low f-numbers) reduce
depth of field, blurring objects behind and in front of the main
subject. Small apertures (high f-numbers) increase depth of
field, bringing out details in the background and foreground.
Short field depths are generally used in portraits to blur background details, long field depths in landscape photographs to
bring the foreground and background into focus.
Large aperture (f/5.6)Small aperture (f/16)
❚❚ Choosing an Aperture
Rotate the multi selector counterclockwise for larger apertures (lower f-numbers), clockwise for smaller apertures
(higher f-numbers). The minimum and
maximum values depend on the lens currently in use.
R
69
M Manual
Command dial
In manual mode, you control both shutter speed and aperture.
❚❚ Choosing Shutter Speed and Aperture
Adjust shutter speed and aperture with
reference to the exposure indicator
(0 71). Rotate the command dial to
adjust shutter speed and the multi selector to adjust aperture: rotate the control
to the right for faster shutter speeds or
smaller apertures (higher f-numbers), to
the left for slower shutter speeds and
larger apertures (lower f-numbers). Shutter speeds can be set to values as fast as
R
1
/
16,000 s or as slow as 30 s, or to “Bulb” to
hold the shutter open indefinitely for a
long time-exposure (0 72). Aperture can be set to values
between the minimum and maximum for the lens.
Continuous Shooting
A
The selected shutter speed may change when a frame rate of 10 fps or
faster is selected in continuous shooting mode (0 97).
70
The Exposure Indicator
A
When shutter speeds other than “Bulb” are
selected, the exposure indicator shows
whether the photograph would be underor over-exposed at current settings.
Optimal exposureUnderexposed by
ISO Sensitivity (P, S, A, and M Modes)
A
Whe n an “a uto” opti on is sel ecte d for ISO sensitivity (0 172), the camera will automatically adjust sensitivity within the selected range if
optimal exposure can not be achieved at the selected shutter speed or
aperture.
The & (Feature) Menu (0 11)
A
Pressing & in mode P, S, A, or M displays the items listed below.
Picture Control ..................................173
White balance....................................167
5
R
71
Long Time-Exposures (M Mode Only)
Command dial
Select a shutter speed of “Bulb” for long
time-exposures of moving lights, the
stars, night scenery, or fireworks. The
shutter remains open while the shutterrelease button is held down. To prevent
blur, use a tripod.
Ready the camera.
1
Mount the camera on a tripod or place it on a stable, level surface. To prevent loss of power before the exposure is complete, use a fully charged battery or an optional AC adapter
and power connector. Note that noise (bright spots, ran-
R
domly-spaced bright pixels, or fog) may be present in long
exposures. Bright spots and fog can be reduced by choosing
On for Long exposure NR in the shooting menu (0 179).
Choose a shutter speed of “Bulb”.
2
Rotate the command dial to the left to
select “Bulb”.
72
Open the shutter.
3
After focusing, press the shutter-release button all the way
down. Keep the shutter-release button pressed until the
exposure is complete.
Close the shutter.
4
Take your finger off the shutter-release button.
Shooting ends automatically after about two minutes. Note that
some time may be required to record long exposures.
R
73
a Photographing Subjects in Motion (Sports Mode)
Choose a (sports) mode for sporting events and other scenes
with fast-moving subjects. The camera takes pictures continuously while the shutter-release button is pressed (0 97).
Select sports mode.
1
Rotate the mode dial to a.
Display release mode options.
2
R
Press 4 (C) to display release mode
options.
Select a frame rate.
3
Highlight the desired frame rate and
press J. Frame rate is expressed in
terms of the number of frames
recorded per second (fps); choose
from frame rates of approximately 5,
10, 20, 30, and 60 fps (I, Q, R,S, and T, respectively). Except when I is selected, the
maximum number of shots that can be recorded in a single
burst is 20.
Compose the shot and start shooting.
4
The camera takes pictures while the
shutter-release button is held all the
way down.
74
The & (Feature) Menu
A
The & menu is not available.
Sports Mode
A
The camera uses single-point (0 188), continuous-servo autofocus
(0 184). The flash, AF-assist illuminator, face priority (0 191), and
image review (0 195) turn off automatically.
Burst Photography
D
While photographs are being recorded to the memory card, the memory card access lamp will light (0 35). Depending on shooting conditions and memory card write speed, recording may continue for some
time after shooting ends. If the battery is exhausted before all photographs are recorded, the shutter-release will be disabled and the
remaining images transferred to the memory card.
Viewing Photographs
A
Each burst plays back as a group. This can be changed using the
Sequence display options item in the playback menu (0 152).
Buffer Size
A
The camera is equipped with a memory buffer for temporary storage, allowing shooting
to continue while photographs are being
saved to the memory card. The approximate
number of images that can be stored in the
memory buffer at current settings is displayed while the shutter-release button is
pressed halfway (this number is an approximation only and varies with
shooting conditions). The illustration shows the display when space
remains in the buffer for about 20 pictures.
R
75
u Choosing the Moment (Best Moment Capture)
Choose a shot from 20 frames recorded to temporary storage
shortly before or after the shutter is released (Active Selection),
choose the moment to release the shutter as the scene plays
back in slow motion (slow view), or let the camera choose the
best shot based on composition and movement (Smart Photo
Selector).
Choosing a Shot Manually (Active Selection)
Choose up to 20 shots from 20 frames recorded shortly before or
after the shutter-release button is pressed all the way down.
R
Select u mode.
1
Rotate the mode dial to u (best
moment capture).
76
Choose Active Selection.
2
Press & (feature) to display the &
menu. Highlight Best moment cap-
ture and press J, then highlight
Active Selection and press J.
Frame the photograph.
3
Compose the photograph with your
subject in the center of the frame.
Begin buffering photographs.
4
Press the shutter-release button halfway to focus (0 34). A & icon will be
displayed as the camera begins
recording images to the memory buffer.
R
77
R
Shoot.
5
Smoothly press the shutter-release
button the rest of the way down. The
20 frames recorded to the buffer in the
moments before and after the shutterrelease button was pressed all the way
down will be copied to temporary
storage, and an indicator will appear
at the top of the display.
Select up to 20 frames.
6
Press 4 or 2 to scroll through the
frames and press 1 or 3 to select or
deselect (the number of frames
selected by default varies with the
option selected for Frames saved(default) in the & (feature) menu).
Selected images are shown by dots in
the indicator.
Save the selected frames.
7
Press J to save the selected frames to the memory card. The
memory card access lamp will light while recording is in progress; note that depending on shooting conditions and memory card write speed, some time may be required to save the
selected frames. Once recorded, the frames will be treated as
a single group during playback.
Number of frames
discarded
Number of frames
saved
78
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.