Thank you for your purchase of a Nikon digital camera. To get
the most from your camera, please be sure to read all instructions thoroughly and keep them where they will be read by all
who use the product.
Camera Settings
The explanations in this manual assume that default settings are used.
Symbols and Conventions
To make it easier to find the information you need, the following symbols and conventions are used:
This icon marks cautions; information that should be read before
D
use to prevent damage to the camera.
This icon marks notes; information that should be read before
A
using the camera.
This icon marks references to other pages in this manual.
0
Digitutor
“Digitutor”, a series of “watch and learn” manuals in movie form, is available from the following website:
http://www.nikondigitutor.com/index_eng.html
A For Your Safety
Before using the camera for the first time, read the safety instructions in
“For Your Safety” (0 x–xii).
Getting the Most from Your Camera0ii
Table of Contents0iv
Introduction01
s
Auto Photo Mode0 21
z
Creative Mode0 27
6
Smart Photo Selector Mode0 35
8
Movie Mode0 41
y
Motion Snapshot Mode0 49
9
Available Settings0 53
7
More on Photography0 57
t
More on Playback0 67
I
Connections0 79
Q
The Playback Menu0 97
o
The Shooting Menu0 107
i
The Setup Menu0 155
g
Technical Notes0 165
n
i
Getting the Most from Your Camera
Take pictures or movies in any of five modes.
Choose q z Motion Snapshot mode
(0 49) to record both photographs and
brief movie vignettes,
w y Smart Photo Selector mode
(0 35) to capture fleeting changes of
expression and other hard-to-time
shots,
e C auto photo mode (0 21) to sim-
plify photography by leaving the camera in charge of settings,
r w creative mode (0 27) to use
special effects, match settings to the
scene, or shoot in exposure modes P, S, A,
or M, or
t 1 movie mode (0 41) to record
high-definition or slow-motion movies.
Combine photos, movies, and music.
q Install the supplied software
(0 79), w copy photos and movies to
your computer (0 83), and e use
Short Movie Creator to create short
movies (0 86).
ii
View short movies in high definition.
q Tra nsf er short movies to the camera (0 87) and use an
HDMI cable to w connect the camera to an HDTV (0 88).
Accessories
Expand your photographic horizons with a wide variety of interchangeable lenses and other accessories (0 165).
Lens es
Software for
Nikon digital
cameras
(available on
CD)
Remote
controls
Mount
adapter
iii
Table of Contents
Getting the Most from Your Camera .........................................ii
Nikon 1 J2 Digital Camera ..............................................................189
Battery Life ...........................................................................................204
Index ............................................................................................205
ix
For Your Safety
To prevent damage to your Nikon product or injury to yourself or to others,
read the following safety precautions in their entirety before using this equipment. Keep these safety instructions where all those who use the product will
read them.
The consequences that could result from failure to observe the precautions
listed in this section are indicated by the following symbol:
This icon marks warnings. To prevent possible injury, read all warn-
A
ings before using this Nikon product.
❚❚WARNINGS
Keep the sun out of the frame. Keep the
A
sun well out of the frame when
shooting backlit subjects. Sunlight
focused into the camera when the
sun is in or close to the frame could
cause a fire.
Turn off immediately in the event of mal-
A
function. Should you notice smoke or
an unusual smell coming from the
equipment or AC adapter (available
separately), unplug the AC adapter
and remove the battery immediately,
taking care to avoid burns. Contin ued
operation could result in injury. After
removing the battery, take the equipment to a Nikon-authorized service
center for inspection.
Do not use in the presence of flammable
A
gas. Do not use electronic equipment
in the presence of flammable gas, as
this could result in explosion or fire.
Do not disassemble. Touching the prod-
A
uct’s internal parts could result in
injury. In the event of malfunction,
the product should be repaired only
by a qualified technician. Should the
product break open as the result of a
fall or other accident, remove the battery and/or AC adapter and then take
the product to a Nikon-authorized
service center for inspection.
Keep out of reach of children. Failure to
A
observe this precaution could result
in injury. In addition, note that small
parts constitute a choking hazard.
Should a child swallow any part of
this equipment, consult a physician
immediately.
Do not place the strap around the neck of
A
an infant or child. Placing the camera
strap around the neck of an infant or
child could result in strangulation.
x
Do not remain in contact with the camera,
A
battery, or charger for extended periods
while the devices are on or in use. Parts of
the device become hot. Leaving the
device in direct contact with the skin
for extended periods may result in
low-temperature burns.
Do not aim the flash at the operator of a
A
motor vehicle. Failure to observe this
precaution could result in accidents.
Observe caution when using a flash.
A
• Using the camera with the flash in
close contact with the skin or other
objects could cause burns.
• Using a flash close to the subject’s
eyes could cause temporary visual
impairment. Particular care should
be observed when photographing
infants, when the flash should be no
less than one meter (39 in.) from the
subject.
Avoid contact with liquid crystal. Should
A
the displays break, care should be
taken to avoid injury due to broken
glass and to prevent the liquid crystal
from the displays touching the skin or
entering the eyes or mouth.
Observe proper precautions when handling
A
batteries. Batteries may leak or
explode if improperly handled.
Observe the following precautions
when handling batteries for use in
this product:
• Use only batteries approved for use
in this equipment.
• Do not short or disassemble the
battery.
• Be sure the product is off before
replacing the battery. If you are
using an AC adapter, be sure it is
unplugged.
• Do not attempt to insert the batter y
upside down or backwards.
• Do not expose the battery to flame
or to excessive heat.
• Do not immerse in or expose to
water.
• Replace the terminal cover when
transporting the battery. Do not
transport or store the battery with
metal objects such as necklaces or
hairpins.
• Batteries are prone to leakage when
fully discharged. To avoid damage
to the product, be sure to remove
the battery when no charge
remains.
• When the battery is not in use,
attach the terminal cover and store
in a cool, dry place.
• The battery may be hot immedi-
ately after use or when the product
has been used on battery power for
an extended period. Before removing the battery turn the camera off
and allow the battery to cool.
• Discontinue use immediately
should you notice any changes in
the battery, such as discoloration or
deformation.
xi
Observe proper precautions when handling
A
the charger:
• Keep dry. Failure to observe this
precaution could result in fire or
electric shock.
• Do not short the charger terminals.
Failure to observe this precaution
could result in overheating and
damage to the charger.
• Dust on or near the metal parts of
the plug should be removed with a
dry cloth. Continued use could
result in fire.
• Do not go near the charger during
thunderstorms. Failure to observe
this precaution could result in electric shock.
• Do not handle the plug or charger
with wet hands. Failure to observe
this precaution could result in electric shock.
• Do not use with travel converters or
adapters designed to convert from
one voltage to another or with DCto-AC inverters. Failure to observe
this precaution could damage the
product or cause overheating or fire.
Use appropriate cables. When connect-
A
ing cables to the input and output
jacks, use only the cables provided or
sold by Nikon for the purpose to
maintain compliance with product
regulations.
CD-ROMs: CD-ROMs containing soft-
A
ware or manuals should not be
played back on audio CD equipment.
Playing CD-ROMs on an audio CD
player could cause hearing loss or
damage the equipment.
xii
Notices
• No part of the manuals included
with this product may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form,
by any means, without Nikon’s prior
written permission.
• Nikon reserves the right to change
the specifications of the hardware
and software described in these
manuals at any time and without
prior notice.
Notice for Customers in Canada
CAUTION
This Class B digital apparatus complies with Canadian ICES-003.
Notice for Customers in Europe
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
This symbol indicates that
this product is to be collected separately.
The following apply only to
users in European countries:
• This product is designated for separate collection at an appropriate collection point. Do not dispose of as
household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
• Nikon will not be held liable for any
damages resulting from the use of
this product.
• While every effort has been made to
ensure that the information in these
manuals is accurate and complete,
we would appreciate it were you to
bring any errors or omissions to the
attention of the Nikon representative in your area (address provided
separately).
ATTENTION
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
This symbol on the battery
indicates that the battery is
to be collected separately.
The following apply only to
users in European countries:
• All batteries, whether marked with
this symbol or not, are designated
for separate collection at an appropriate collection point. Do not dispose of as household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
xiii
Notice for Customers in the U.S. A.
The Battery Charger
IMPORTANT SAFETY INSTRUCTIONS—SAVE THESE
INSTRUCTIONS
DANGER—TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS
For connection to a supply not in the U.S.A., use an attachment plug adapter
of the proper configuration for the power outlet if needed. This power unit
is intended to be correctly oriented in a vertical or floor mount position.
Federal Communications Commission (FCC) Radio Frequenc y Interference Statement
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced
radio/television technician for help.
xiv
CAUTIONS
Modifications
The FCC requires the user be notified
that any changes or modifications
made to this device that are not
expressly approved by Nikon Corporation may void the user’s authority to
operate the equipment.
Interface Cables
Use the interface cables sold or provided by Nikon for your equipment.
Using other interface cables may
exceed the limits of Class B Part 15 of
the FCC rules.
Notice for Customers in the State of
California
WARNING
: Handling the cord on this product may expose you to lead, a chemical
known to the State of California to cause
birth defects or other reproductive
harm.
Wash hands after handling
Nikon Inc., 1300 Walt Whitman Road,
Melville, New York 11747-3064, U.S.A.
Tel.: 631-547-4200
.
Notice Concerning Prohibition of Copying or Reproduction
Note that simply being in possession of material that has been digitally copied or reproduced by means of a scanner, digital camera, or other device may
be punishable by law.
• Items prohibited by law from being copied
or reproduced
Do not copy or reproduce paper
money, coins, securities, government bonds, or local government
bonds, even if such copies or reproductions are stamped “Sample.”
The copying or reproduction of
paper money, coins, or securities
which are circulated in a foreign
country is prohibited.
Unless the prior permission of the
government has been obtained, the
copying or reproduction of unused
postage stamps or post cards issued
by the government is prohibited.
The copying or reproduction of
stamps issued by the government
and of certified documents stipulated by law is prohibited.
Disposing of Data Storage Devices
Please note that deleting images or formatting memory cards or other data
storage devices does not completely erase the original image data. Deleted
files can sometimes be recovered from discarded storage devices using commercially available software, potentially resulting in the malicious use of personal image data. Ensuring the privacy of such data is the user’s
responsibility.
Before discarding a data storage device or transferring ownership to another
person, erase all data using commercial deletion software, or format the
device and then completely refill it with images containing no private information (for example, pictures of empty sky). Care should be taken to avoid
injury when physically destroying data storage devices.
• Cautions on certain copies and reproduc-
tions
The government has issued cautions
on copies or reproductions of securities
issued by private companies (shares,
bills, checks, gift certificates, etc.), commuter passes, or coupon tickets, except
when a minimum of necessary copies
are to be provided for business us e by a
company. Also, do not copy or reproduce passports issued by the government, licenses issued by public
agencies and private groups, ID cards,
and tickets, such as passes and meal
coupons.
• Comply with copyright notices
The copying or reproduction of
copyrighted creative works such as
books, music, paintings, woodcuts,
prints, maps, drawings, movies, and
photographs is governed by
national and international copyright
laws. Do not use this product for the
purpose of making illegal copies or
to infringe copyright laws.
BY
OBTAINEDFROMAVIDEOPROVIDERLICENSEDTOPROVIDE AV C VIDEO. NOLICENSEIS
GRANTEDORSHALLBEIMPLIEDFORANYOTHERUSE. ADDITIONALINFORMATIONMAYBE
OBTAINEDFROM MPEG LA, L.L.C. SEEhttp://www.mpegla.com
Temperature Warnings
The camera may become warm to the touch during use; this is normal and
does not indicate a malfunction. At high ambient temperatures, after
extended periods of continuous use, or after several photographs have been
taken in quick succession, a temperature warning may be displayed, following which the camera will turn off automatically to minimize damage to its
internal circuits. Wait for the camera to cool before resuming use.
Use Only Nikon Brand Electronic Accessories
Nikon cameras are designed to the highest standards and include complex
electronic circuitry. Only Nikon brand electronic accessories (including chargers, batteries, AC adapters, and flash accessories) certified by Nikon specifically for use with this Nikon digital camera are engineered and proven to
operate within the operational and safety requirements of this electronic circuitry.
The use of non-Nikon electronic accessories could damage
the camera and may void your Nikon warranty. The use of
third-party rechargeable Li-ion batteries not bearing the
Nikon holographic seal shown at right could interfere with
normal operation of the camera or result in the batteries overheating, igniting, rupturing, or leaking.
For more information about Nikon brand accessories, contact a local authorized Nikon dealer.
xvi
Use Only Nikon Brand Accessories
D
Only Nikon brand accessories certified by Nikon specifically for use
with your Nikon digital camera are engineered and proven to operate
within its operational and safety requirements. T
ACCESSORIES
RANTY.
A
The camera is a precision device and requires regular servicing. Nikon
recommends that the camera be inspected by the original retailer or a
Nikon-authorized service representative once every one to two years,
and that it be serviced once every three to five years (note that fees
apply to these services). Frequent inspection and servicing are particularly recommended if the camera is used professionally. Any accessories regularly used with the camera, such as lenses, should be included
when the camera is inspected or serviced.
A
Before taking pictures on important occasions (such as at weddings or
before taking the camera on a trip), take a test shot to ensure that the
camera is functioning normally. Nikon will not be held liable for damages or lost profits that may result from product malfunction.
A
As part of Nikon’s “Life-Long Learning” commitment to ongoing product support and education, continually-updated information is available on-line at the following sites:
• For users in the U.S. A.: http://www.nikonusa.com/
• For users in Europe and Afric a: http://www.europe-nikon.com/support/
• For users in Asia, Oceania, and the Middle East: http://www.nikon-asia.com/
Visit these sites to keep up-to-date with the latest product information,
tips, answers to frequently-asked questions (FAQs), and general advice
on digital imaging and photography. Additional information may be
available from the Nikon representative in your area. For contact information, visit http://imaging.nikon.com/
COULDDAMAGEYOURCAMERAANDMAYVOIDYOUR NIKONWAR-
Servicing the Camera and Accessories
Before Taking Important Pictures
Life-Long Learning
HEUSEOFNON-NIKON
xvii
xviii
Introduction
s
Package Contents
Confirm that the package contains the following items.
Nikon 1 J2 digital camera
EN-EL20
rechargeable
Li-ion battery
(with terminal cover)
UC-E15
USB cable
AN-N1000 strap
ViewNX 2/Short
Movie Creator CD
Memory cards are sold separately.
Warra nty
User’s Manual
BF-N1000 body cap
s
MH-27 battery
charger (AC wall
adapter or power cable
supplied in countries or
regions where required;
shape depends on
countr y of sale )
Lens (supplied only if
lens kit is purchased with
camera; comes w ith front
and rear lens caps)
Reference manual
CD (contains this manual)
1
Parts of the Camera
Take a few moments to familiarize yourself with camera controls
and displays. You may find it helpful to bookmark this section
and refer to it as you read through the rest of the manual.
Press $ to cycle through shooting
(0 4) and playback (0 67) indicators as
shown below.
❚❚ Shooting❚❚ Playback
Simplified display
Detailed display
The Framing Grid
A
A framing grid can be displayed by selecting
On for Grid display in the setup menu
(0 158).
Simple photo info
Detailed photo info
Image only
$ button
s
5
The Mode Dial
The camera offers a choice of the following shooting modes:
s
Motion Snapshot mode (0 49): Each time the shutter is released, the cam-
era records a still image and about a second of movie footage. When the
resulting “Motion Snapshot” is viewed on the camera, the movie will
play back in slow motion over approximately 2.5 s, followed by the still
image.
Smart Photo Selector mode (0 35): Each time
the shutter is released, the camera automatically selects the best shot and four
best shot candidates based on composition and motion.
Auto photo mode (0 21): For photographs.
The camera automatically adjusts settings to suit the subject.
Creative mode (0 27): For photographs in
which you want to use special effects,
match settings to the scene, or shoot in
exposure modes P, S, A, or M.
Movie mode (0 41): Record HD or slow-motion movies.
Mode dial
6
The Multi Selecor
The multi selector and J button are
used to adjust settings and navigate the
camera menus.
Multi selector
Settings: A
Lock exposure (0 125) and/or focus (0 150).
Menu navigation: 1
Move cursor up.
Select highlighted
item.
Settings: E
View self-timer/
remote-control menu
(0 57).
Menu navigation: 4
Return to previous
menu.
Settings: M
View flash mode menu (0 62).
Menu navigation: 3
Move cursor down.
Settings: E
View exposure compensation menu
(0 60).
Menu navigation: 2
Select highlighted item
or display sub-menu.
Note: You can also highlight items by rotating the multi selector.
The Multi Selector
A
In this manual, the 1, 2, 3, and 4 symbols are used to
represent up, right, down, and left on the multi selector.
Items can be highlighted by rotating the multi selector
as shown at right.
s
7
The G Button
Most shooting, playback, and setup
options can be accessed from the camera
menus. To view the menus, press the
G button.
s
Tab s
Choose from the following menus:
K Playback menu (097)B Setup menu (0 155)
C y 1 w z Shooting menu (0 107)
Menu options
Options in current menu.
Slider shows position in current
menu.
G button
8
❚❚ Using the Menus
Use the multi selector to navigate the
menus (0 7).
Multi selector
Press 1 or 3 to select the tab then press 2 to display menu
1
items.
Highlight menu item and press 2 to display options.
2
Highlight desired option and press J to select.
3
s
Using the Menus
A
The items listed may vary with camera settings. Items displayed in gray
are not currently available (0 53). To exit the menus and return to
shooting mode, press the shutter-release button halfway (0 22).
9
The & (Feature) Button
The & button gives access to the following features in creative, movie, Motion
Snapshot, and playback modes. Press &
and use the multi selector (or W control)
and J button to adjust options.
s
• Scene (creative mode): Choose from P, S, A, M, Night landscape
(j), Night portrait (o), Backlighting (m), Easy panorama
(p), Soft (q), Miniature effect (r), and Selective color (s).
• Movie mode (movie recording; 0 44): Choose from high-defini-
tion (HD movie) and slow-motion (Slow motion) recording.
• Theme (Motion Snapshot mode; 0 51): Choose from Beauty,
Wave s, Relaxation, and Tenderness.
• Rating (playback mode; 0 74): Rate pic-
tures.
& button
10
First Steps
Attach the camera strap.
1
Attach the strap securely to the two camera eyelets.
Charge the battery.
2
Insert the battery q and plug the charger in w. An exhausted
battery fully charges in about two hours. Unplug the charger
and remove the battery when charging is complete.
Battery
charging
Charging
complete
The Plug Adapter
A
Depending on the country or region of
purchase, a plug adapter may be supplied with the charger.
adapter varies with the country or region
of purchase. If a plug adapter is supplied,
raise the wall plug and connect the plug
adapter as shown at right, making sure
the plug is fully inserted.
adapter could damage the product.
The shape of the
Attempting to forcibly remove the plug
s
11
s
The Battery and Charger
D
Read and follow the warnings and cautions on pages x–xii and 173–
176 of this manual. Do not use the battery at ambient temperatures
below 0°C (32 °F) or above 40°C (104°F); failure to observe this precaution could damage the battery or impair its performance.
Capacity may be reduced and charging times may increase at battery temperatures from 0°C (32°F) to 10°C (50°F) and from 45°C
(113°F) to 60 °C (140°F); the battery will not charge if its temperature is below 0°C (32°F) or above 60°C (140°F).
Charge the battery at ambient temperatures between 5°C (41 °F)
and 35°C (95 °F). If the CHARGE lamp flashes quickly during charging,
cease use immediately and take battery and charger to your retailer
or a Nikon-authorized service representative.
Do not move the charger or touch the battery during charging. Failure to observe this precaution could in very rare instances result in
the charger showing that charging is complete when the battery is
only partially charged. Remove and reinsert the battery to begin
charging again.
Use the charger with compatible batteries only. Unplug when not
in use.
12
Insert the battery and a memory card.
3
Check to be sure the battery and card are in the correct orientation. Using the battery to keep the orange battery latch
pressed to one side, slide the battery in until it latches, and
then slide in the memory card until it clicks into place.
Rear
s
13
s
Inserting and Removing Batteries and Memo ry Cards
D
Always turn the camera off before inserting or removing batteries
or memory cards. Note that the battery may be hot after use;
observe due caution when removing the battery.
Formatting Memory Cards
A
If this is the first time the memory card
will be used in the camera or if the card
has been formatted in another device,
select Format memory card in the setup
menu and follow the on-screen instructions to format the card (0 157). Note
that this permanently deletes any data the
card may contain. Be sure to copy any
photographs and other data you wish to
keep to a computer before proceeding.
The Write Protect Switch
A
Memory cards are equipped
with a write protect switch to
prevent accidental loss of data.
When this switch is in the “lock”
position, the memory card can
not be formatted and photos can not be deleted or recorded. To
unlock the memory card, slide the switch to the “write” position.
GB
16
Write-protect switch
14
Removing Batteries and Memory Cards
A
After turning the camera off, confirm that
the memory card access lamp (
and open the battery-chamber/memory
card slot cover. To remove the battery, first
release it by pressing the orange battery
latch in the direction shown by the arrow
and then remove the battery by hand.
To remove a memory card, first press the
card in to eject it (q); the card can then
be removed by hand (w).
Memory Cards
D
• The camera stores pictures on SD, SDHC, and SDXC memory cards
(available separately; 0 168).
• Memory cards may be hot after use. Observe due caution when
removing memory cards from the camera.
• Do not remove memory cards from the camera, turn the camera
off, or remove or disconnect the power source during formatting
or while data are being recorded, deleted, or copied to a computer. Failure to observe these precautions could result in loss of
data or in damage to the camera or card.
• Do not touch the card terminals with your fingers or metal objects.
• Do not bend, drop, or subject to strong physical shocks.
• Do not apply force to the card casing. Failure to observe this pre-
caution could damage the card.
• Do not expose to water, heat, high levels of humidity, or direct
sunlight.
• Do not format memory cards in a computer.
0
3) is off
s
15
s
Attach a lens.
4
Be careful to prevent dust from entering the camera when the
lens or body cap is removed. The lens generally used in this
manual for illustrative purposes is a 1 NIKKOR VR 10–30mm
f/3.5–5.6. See page 143 for information on vibration reduction (VR), page 197 for information on detaching lenses.
Mounting mark (lens)
Mounting mark (lens)
A
Lenses with retractable lens barrel buttons can not be used when retracted. To
unlock and extend the lens, keep the
retractable lens barrel button pressed (q)
while rotating the zoom ring (w). The
lens can be retracted and the zoom ring
locked by pressing the retractable lens
barrel button and rotating the ring in the opposite direction. Be
careful not to press the retractable lens barrel button while attaching or removing the lens.
16
Mounting mark
(camera)
Lenses with Retractable Lens Barrel Buttons
Keeping marks aligned, position lens on
camera, then rotate until it clicks into place.
Turn the camera on.
5
Press the power switch to turn the
camera on. The power lamp will
briefly light green and the monitor will
turn on. Be sure to remove the lens
cap before shooting.
Turning the Camera Off
A
To turn the camera off, press the power switch again. The monitor
will turn off.
Auto Power Off
A
If no operations are performed for about 30 seconds, the displays
will turn off and the power lamp start to flash (if desired, the delay
before the displays turn off automatically can be changed using the
Auto power off option in the setup menu; 0 159). The camera can
be reactivated by operating the buttons, mode dial, or other camera
controls. If no operations are performed for about three minutes
after the displays have turned off, the camera will turn off automatically.
Attaching and Removing Lenses
A
Turn the camera off before attaching or removing lenses. Note that
when the camera is turned off, the sensor protection barrier in the
lens will close, protecting the camera image sensor.
Lenses with Retractable Lens Barrel Buttons
A
If you are using a lens with a retractable lens barrel button (0 16),
the camera will automatically turn on when the retractable lens barrel lock is released; in addition, if the view through the lens is displayed or the monitor is off, the camera will turn off when the lens
barrel is locked (in the case of 1 NIKKOR VR 10–30mm f/3.5–5.6 and
1 NIKKOR VR 30–110mm f/3.8–5.6 lenses, firmware version 1.10 or
later is required if locking the lens barrel is to turn the camera off
when the monitor is off; for information on updating lens firmware,
visit the Nikon website for your area).
s
17
s
Choose a language and set the clock.
6
A language-selection dialog will be displayed the first time
the camera is turned on. Use the multi selector and J button
(0 9) to choose a language and set the camera clock. Photos
can not be taken until you have set the time and date.
18
Press 1 or 3 to highlight
language and press J.
Press 1 or 3 to highlight date
format and press J.
Press 4 or 2 to select items and
press 1 or 3 to change. Press J
when finished.
Press 4 or 2 to highlight time
zone and press J.
Press 1 or 3 to highlight daylight
saving time option and press J.
Note: The camera uses a 24-hour
clock. Language and clock can be
changed at any time using
Language (0 162) and Tim e
zone and date (0 162) options in
setup menu.
The Camera Clock
A
The camera clock is less accurate than most watches and household
clocks. Check the clock regularly against more accurate time pieces
and reset as necessary.
The camera clock is powered by an independent, rechargeable
power source, which is charged as necessary when the main battery
is installed or the camera is powered by an optional EP-5C power
connector and EH-5b AC adapter (0 170). Three days of charging
will power the clock for about a month. If a message warning that
the clock has been reset is displayed when the camera is turned on,
the clock battery is exhausted and the clock has been reset. Set the
clock to the correct time and date.
s
19
s
Check the battery level and memory card capacity.
7
Check the battery level and number
Battery level
of exposures remaining in the monitor.
❚❚ Battery Level
DisplayDescription
Battery fully charged or
NO ICON
H
Cannot take pictures.
Insert fully-charged
battery.
partially discharged;
level shown by L or
K icon in detailed
display (0 5).
Low battery. Ready
fully-charged battery or
prepare to charge
battery.
Battery exhausted;
shutter-release
disabled. Insert charged
battery.
Exposures remaining
❚❚ Number of Exposures Remaining
The monitor shows the number of pictures that can be stored
on the memory card at current settings (values over 1000 are
rounded down to the nearest hundred; e.g., values between
1200 and 1299 are shown as 1.2 K). If a warning is displayed
stating that there is not enough memory for additional
images, insert another memory card (0 13) or delete some
photos (0 73).
20
Auto Photo Mode
z
Auto photo mode is the mode generally used for taking photos.
Taking Photos in Auto Photo Mode
Select auto photo mode.
1
Rotate the mode dial to C.
Ready the camera.
2
Hold the camera securely with both
hands, being careful not to obstruct
the lens, AF-assist illuminator, or
microphone. Rotate the camera as
shown at lower right when taking pictures in “tall” (portrait) orientation.
Shutter speeds slow when lighting is
poor; use of the built-in flash (0 62) or
a tripod is recommended.
Availabl e Settings
A
For information on the options available in auto photo mode, see page
53.
z
21
Frame the photograph.
3
Position your subject in the center of
the frame.
The Shutter-Release Button
A
The camera has a two-stage shutter-release button. The camera
focuses when the shutter-release button is pressed halfway. To take the
photograph, press the shutter-release button the rest of the way down.
z
Focus: Press halfwayShoot: Press the rest
Automatic Scene Selection
A
In auto photo mode, the camera automatically analyzes the subject and selects the
appropriate scene. The selected scene is
shown by an icon in the display.
c Por trait: Human portrait subjects.
d Landscape: Landscapes and cityscapes.
f Night portrait: Portrait subjects framed against dark backgrounds.
e Close up: Subjects close to the camera.
Z Auto: Subjects that do not fall into the categories listed above.
Movie Recording
A
In auto photo mode, movies can not be recorded and pressing the
movie-record button has no effect.
See Also
A
See page 159 for information on silencing the beep that sounds when
the camera focuses or the shutter is released.
of the way down
Scene icon
22
Focus.
4
Press the shutter-release button halfway to focus. If the subject is poorly lit,
the AF-assist illuminator (0 2) may
light to assist the focus operation.
If the camera is able to focus, the selected
focus area will be highlighted in green
and a beep will sound (a beep may not
sound if the subject is moving).
If the camera is unable to focus, the focus
area will be displayed in red. See page
146.
Shoot.
5
Smoothly press the shutter-release
button the rest of the way down to
release the shutter and record the
photograph. The memory card access
lamp will light and the photograph
will be displayed in the monitor for a
few seconds (the photo will automatically clear from the display and the
camera will be ready to shoot when
the shutter-release button is pressed
halfway). Do not eject the memory card
or remove or disconnect the power
source until the lamp has gone out and
recording is complete.
Focus area
z
Memory card
access lamp
23
Using a Zoo m Lens
A
Use the zoom ring to zoom in on the subject so that it fills a larger
area of the frame, or zoom out to increase the area visible in the final
photograph (select longer focal lengths on the lens focal length
scale to zoom in, shorter focal lengths to zoom out).
Zoom in
Zoom out
z
24
If you are using an optional lens with a
power drive zoom switch, select T to
zoom in and W to zoom out. The speed
with which the camera zooms in and out
varies with how far you slide the switch.
The zoom position is shown by the zoom
guide in the display.
Face -Priori ty AF
A
The camera detects and focuses on portrait subjects (face-priority AF). A double
yellow border will be displayed if a portrait subject is detected facing the camera
(if multiple faces, up to a maximum of
five, are detected, the camera will select
the closest subject). Press the shutterrelease button halfway to focus on the subject in the double yellow
border. The border will clear from the display if the camera can no
longer detect the subject (because, for example, the subject has
looked away).
Zoom ring
Zoom guide
Viewing Photographs
Press K to display your most recent pho-
tograph full frame in the monitor (full-
frame playback).
Press 4 or 2 or rotate the multi selector
to view additional pictures.
To zoom in on the center of the current
image, press the W control up (0 72).
Press W down to zoom out. To view multi-
ple images, press W down when the pic-
ture is displayed full frame (0 70).
K button
z
W control
To end playback and return to shooting mode, press the shutter-
release button halfway.
See Also
A
For information on toggling photo info on or off, see page 67. See page
75 for information on slide shows.
25
Deleting Pictures
To delete the current picture, press O. Note that once deleted, pic-
tures can not be recovered.
Display the photograph.
1
Display the photograph you wish to delete as described on
the preceding page.
Press O.
2
A confirmation dialog will be dis-
z
played.
Delete the photograph.
3
Press O again to delete the picture and
return to playback, or press K to exit
without deleting the picture.
O button
Deleting Multiple Pictures (0 73)
A
The Delete option in the playbac k menu c an be u sed to delete selected
pictures, all pictures, pictures taken on selected dates, or pictures previously selected as candidates for deletion.
26
Creative Mode
6
Choose creative mode when to take photos using special effects,
match settings to the scene, or shoot in exposure modes P, S, A, or
M.
Choosing a Creative Mode
Select creative mode.
1
Rotate the mode dial to w.
Choose a scene.
2
Press the & button and highlight a
scene using the multi selector (0 28).
& button
6
Press J to select the highlighted scene. Your selection
is indicated by an icon in the
display.
27
Choosing a Scene
Creative mode offers a choice of the following scenes:
Control the full range of camera settings and choose
how the camera sets shutter speed and aperture
(0 30).
Each time the shutter-release button is fully pressed,
the camera takes a series of shots and combines
them to capture low lighting in night scenes; during
processing, a message is displayed and no pictures
can be taken. The flash does not fire and the edges of
photos are cropped out. Note that the desired results
may not be obtained if the camera or subject moves
during shooting; if the camera is unable to combine
the images, a warning will be displayed and only
one picture will be taken.
Each time the shutter-release button is fully pressed,
the camera takes a series of shots, some with the
flash and some without, and combines them to capture background lighting in portraits taken at night
or under low light; during processing, a message is
displayed and no pictures can be taken. Raise the
built-in flash before shooting; no photograph will be
taken if the flash is not raised. Note
photos are cropped out and that
may not be obtained if the camera or subject moves
during shooting; if the camera is unable to combine
the images, a warning will be displayed and the camera will take a single picture using the flash.
Shoot panoramas for later viewing on the camera
(0 32).
that
the edges of
the desired results
28
OptionDescription
Shoot photographs with a
soft filter effect. To choose
the amount of softening,
press
J
Soft (q)
Miniature effect (r)
Selective color (s)
when the view
through the lens is displayed, highlight an option
using the multi selector,
and press
The top and bottom of each photo is blurred so that
the subject appears to have been a diorama photographed at short range. Works best when shooting
from a high vantage point.
Take photos in which only
the hue chosen with the
multi selector and
ton appears in color.
J
to select.
J
but-
Note that movies can not be recorded in creative mode and that
pressing the movie-record button has no effect.
Availabl e Settings
A
For information on the options available in creative mode, see page 53.
6
29
P, S, A, M
P, S, A, M mode lets you choose the exposure mode, which controls how the camera sets shutter speed and aperture.
❚❚ Exposure Mode
To choose the exposure mode, press the
G button, highlight Exposure mode
(0 110) in the shooting menu (0 107),
and press 2 to display the options below,
then highlight an option and press J.
The camera sets shutter speed and aperture for
P Programmed auto
6
S Shutter-priority auto
A Aperture -priority auto
M Manual
optimal exposure (0 112). Recommended for
snapshots and in other situations in which there
is little time to adjust camera settings.
You choose the shutter speed; the camera
selects an aperture for best results (0 113). Use
to freeze or blur motion.
You choose the aperture; the camera selects a
shutter speed for best results (0 114). Use to
blur the background or bring both foreground
and background into focus.
You control both shutter speed and aperture
(0 115).
30
Backlighting
The method used to capture details in shaded areas of back-lit
subjects depends on the option selected for HDR in the shooting menu (0 107).
Details in highlights and shadows are preserved using HDR (high
dynamic range); Z appears in the display. Each time the shutter-
release button is fully pressed, the camera takes two shots in quick
succession and combines them to preserve details in highlights
and shadows in high-contrast scenes; the built-in flash does not
fire. While the shots are combined, a message will be displayed and
the shutter release will be disabled. The final photograph will be
On
displayed when processing is complete.
+
6
First exposure
(darker)
The flash fires to “fill in” (illuminate) shadows in back-lit subjects.
Only one shot is taken when the shutter-release button is fully
Off
pressed, and the flash fires with each shot. No pictures will be taken
if the built-in flash is not raised; raise the flash before shooting.
Framing HDR Photographs
D
The edges of the image will be cropped out. The desired results may
not be achieved if the camera or subject moves during shooting.
Depending on the scene, shading may be uneven and shadows may
appear around bright objects or halos around dark objects. If the camera is unable to successfully combine the two images, a single image
will be recorded at normal exposure and Active D-Lighting (0 139) will
be applied.
Second exposure
(brighter)
Combined HDR
image
31
Easy Panorama
Follow the steps below to shoot panoramas. During shooting,
the camera focuses using auto-area AF (0 149); face-priority AF
(0 24) is not available. Exposure compensation (0 60) can be
used, but the built-in flash will not fire.
Set focus and exposure.
1
Frame the start of the panorama and press the shutter-release button halfway.
Guides will appear in the
display.
6
Start shooting.
2
Press the shutter-release
button the rest of the way
down and then lift your finger from the button. a, c,d, and b icons will appear in
the display to indicate the
possible pan directions.
Pan the camera.
3
Slowly pan the camera up, down, left,
or right as shown below. Shooting will
start when the camera detects the pan
direction and a progress indicator will
appear in the display. Shooting ends
automatically when the end of the
panorama is reached.
Progress indicator
32
An example of how to pan the camera is shown below. Without changing your position, pan the camera in a steady curve
either horizontally or vertically. Time the pan according to
the option selected for Image size in the shooting menu:
about 15 seconds are needed to complete the pan when
A Normal panorama is selected, about 30 seconds when
B Wide panorama is selected.
Panoram as
A
High-distortion wide-angle lenses may fail to produce the desired
results. An error message will be displayed if the camera is panned too
quickly or unsteadily.
The completed panorama will be slightly smaller than the area visible
in the display during shooting. No panorama will be recorded if shooting ends before the halfway point; if shooting ends after the halfway
point but before the panorama is complete, the unrecorded portion
will be shown in gray.
6
33
❚❚ Viewing Panoramas
Panoramas can be viewed by pressing J when a panorama is
displayed full frame (0 25). The start of the panorama will be
displayed with the smallest dimension filling the display and the
camera will then scroll through the picture in the original pan
direction.
6
The following operations can be performed:
ToUseDescription
PausePause playback.
PlayJ
Advance/
rewind
Return to
full-frame
playback
34
Resume playback when the panorama is
paused or during rewind/advance.
Press 4 to rewind, 2 to advance. If playback is
paused, the panorama rewinds or advances a
/
segment at a time; keep the button pressed
for continuous rewind or advance. You can
also rotate the multi selector to rewind or
advance.
/K Press 1 or K to exit to full-frame playback.
Navigation
window
Guide
Smart Photo Selector Mode
8
Choose Smart Photo Selector mode for photos that capture a
fleeting expression on the face of a portrait subject or other
hard-to-time shots such as group photos in party scenes. Each
time the shutter is released, the camera automatically selects the
best shot and four best shot candidates based on composition
and motion.
Taking Photos in Smart Photo Selector Mode
Select Smart Photo Selector mode.
1
Rotate the mode dial to y.
Availabl e Settings
A
For information on the options available in Smart Photo Selector mode,
see page 53.
8
35
8
Frame the photograph.
2
Compose the photograph with your
subject in the center of the frame.
Begin buffering photographs.
3
Press the shutter-release button halfway to focus (0 23). An icon will be
displayed as the camera begins
recording images to the memory
buffer. The camera continuously
adjusts focus to account for changes
in the distance to the subject in the AF
area brackets while the shutterrelease button is pressed halfway.
Shoot.
4
Smoothly press the shutter-release
button the rest of the way down. The
camera will compare shots recorded
to the buffer both before and after the
shutter-release button was pressed,
and select five to copy to the memory
card. Note that some time may be
required. The best picture is displayed
in the monitor for a few seconds when
recording is complete.
AF area brackets
36
Buffering
A
Buffering begins when the shutter-release button is pressed halfway
and ends after about 90 seconds or when the shutter-release button is
pressed all the way down.
Shutter-release
button pressed
halfway to focus
Smart Photo Selector Mode
A
The camera automatically chooses a scene mode appropriate to the
subject. Movies can not be recorded, and pressing the movie-record
button has no effect. The flash can not be used.
Shutter-release button
Buffering
pressed all the way
down
Shooting ends
8
37
Viewing Photographs
Press K and use the multi selector to
display photographs taken with the
Smart Photo Selector (0 25; pictures
taken with the Smart Photo Selector are
indicated by a y icon). Of the five photographs recorded by the Smart Photo
Selector, only the best shot will be displayed (when you press the multi selector right to view the next picture, the
camera will skip over the best shot candidates, with the result that the next picture displayed will not have a file
number that immediately follows that of
8
the current picture). To end playback
and return to shooting mode, press the
shutter-release button halfway.
Choosing the Best Shot
When a photograph taken with the
Smart Photo Selector is displayed, you
can choose the best shot by pressing J.
Press 4 or 2 to view the other pictures
in the sequence and press J to select
the current picture as the best shot. To
return to normal playback, press D.
K button
38
Deleting Pictures
Pressing O when a picture taken with the
Smart Photo Selector is selected displays
a confirmation dialog; press O again to
delete the best shot and the four best
shot candidates, or press K to exit with-
out deleting the pictures. Note that oncedeleted, pictures can not be recovered.
Deleting Individual Photographs
A
Pressing the O button in the best shot selection dialog displays the following options;
highlight an option using the multi selector
and press J to select.
• This image: Delete the current photo (note
that the picture currently selected as the
best shot can not be deleted).
• All except best shot: Delete all photos in the sequence except the one
currently selected as the best shot.
A confirmation dialog will be displayed; to delete the selected image or
images, highlight Yes and press J.
O button
8
39
8
40
Movie Mode
y
Choose movie mode to shoot high-definition (HD) or slowmotion (0 45) movies using the movie-record button.
HD Movies
Record movies with sound at an aspect ratio of 16 : 9.
Select movie mode.
1
Rotate the mode dial to 1. An HD
movie crop with an aspect ratio of
16 : 9 will appear in the display.
Frame the opening shot.
2
Frame the opening shot with your
subject in the center of the display.
See Also
A
See page 140 for information on adding fade in/fade out effects. Frame
size and frame rate options are described on page 123.
The 0 Icon
D
A 0 icon indicates that movies can not be recorded.
Availabl e Settings
A
For information on the options available in movie mode, see page 53.
y
41
y
Start recording.
3
Press the movie-record button to
begin recording. A recording indicator, the time elapsed, and the time
available are displayed while recording is in progress.
Audio Recording
A
Be careful not to cover the microphone
and note that the built-in microphone
may record sounds made by the camera
or lens. By default, the camera focuses
continuously; to avoid recording focus
noise, select a focus mode of AF-S (0 144).
The Movie sound options item in the
shooting menu offers sensitivity and
wind noise options for the built-in microphone (0 141).
End recording.
4
Movie-record button
Recording indicator/
Time elapsed
Time available
Press the movie-record button again
to end recording. Recording will end
automatically when the maximum
length is reached (0 123), the memory card is full, another mode is
selected, the lens is removed, or the
camera becomes hot (0 xvi).
Maximum Length
A
HD movies can be up to 4 GB in size and 20 minutes in length (for
more information, see page 123); note that depending on memory
card write speed, shooting may end before this length is reached
(0 168).
Movie-record button
Exposure Lock
A
Exposure will lock while the A (multi selector up) button is pressed
(0 125).
42
❚❚ Taking Photographs During HD Movie Recording
Press the shutter-release button all the
way down to take a photograph without
interrupting HD movie recording. Photographs taken during movie recording
have an aspect ratio of 16 : 9.
Taking Photographs During Movie Recording
A
Up to 15 photographs can be taken with each movie shot. Please note
that photographs can not be taken with slow-motion movies.
y
43
❚❚ Choosing the Movie Type
To choose between high definition and
slow motion recording, press & and use
the multi selector and J button to
choose from the following options:
• HD movie: Record movies in HD.
•
Slow motion
(045).
Recording Movies
D
Flicker, banding, or distortion may be visible in the displays and in the
final movie under fluorescent, mercury vapor, or sodium lamps or if the
y
camera is panned horizontally or an object moves at high speed
through frame (flicker and banding can be reduced in HD movies by
choosing a Fli cker reducti on option that matches the frequency of the
local AC power supply, but note that the slowest shutter speed available is
after-images when the camera is panned. Jagged edges, color fringing,
moiré, and bright spots may also appear. When recording movies,
avoid pointing the camera at the sun or other strong light sources. Failure to observe this precaution could result in damage to the camera’s
internal circuitry.
: Record slow-motion movies
1
/
100 at 50 Hz,
1
/
60 at 60 Hz; 0 161). Bright light sources may leave
& button
44
Slow Motion
Record silent movies with an aspect ratio of 8 : 3. Movies are
recorded at 400 fps and play back at 30 fps.
Select movie mode.
1
Rotate the mode dial to 1.
Select slow-motion mode.
2
Press the & button and use the multi
selector and J button to select Slowmotion. A slow-motion movie crop
with an aspect ratio of 8 : 3 will appear
in the display.
& button
Frame the opening shot.
3
Frame the opening shot with your
subject in the center of the display.
y
45
Start recording.
4
Press the movie-record button to
begin recording. A recording indicator, the time elapsed, and the time
available are displayed while recording is in progress. The camera focuses
on the subject at the center of the display; face detection (0 24) is not
available.
Movie-record button
Recording indicator/
Time elapsed
y
End recording.
5
Press the movie-record button again
to end recording. Recording will end
automatically when the maximum
length is reached, the memory card is
full, another mode is selected, the
lens is removed, or the camera
becomes hot (0 xvi).
Maximum Length
A
Up to 5 seconds or 4 GB of footage can be recorded; note that
depending on memory card write speed, shooting may end before
this length is reached (0 168).
See Also
A
Frame rate options are described on page 123.
46
Time available
Movie-record button
Viewing Movies
Movies are indicated by a 1 icon in full-frame playback (0 25).
Press J to start playback.
1 icon/Length
The following operations can be performed:
ToUseDescription
PausePause playback.
Movie playback indicator/
Current position/total length
GuideVolume
y
PlayJ
Advance/
rewind
Adjust
volume
Return to
full-frame
playback
Resume playback when the movie is paused
or during rewind/advance.
Press 4 to rewind, 2 to advance. Speed
increases with each press, from 2× to 5× to
/
10× to 15×. If playback is paused, the movie
rewinds or advances one frame at a time; keep
the button pressed for continuous rewind or
advance. You can also rotate the multi selector
to rewind or advance when playback is
paused.
Press up to increase volume, down to
W
decrease.
/K Press 1 or K to exit to full-frame playback.
47
Deleting Movies
To delete the current movie, press O. A
confirmation dialog will be displayed;
press O again to delete the movie and
return to playback, or press K to exit
without deleting the movie. Note thatonce deleted, movies can not be recovered.
See Also
A
See page 104 for information on trimming
unwanted footage from movies.
y
O button
48
Motion Snapshot Mode
9
Choose Motion Snapshot mode to record brief movie vignettes
with your photographs. Each time the shutter is released, the
camera records a still image and about a second of movie footage. When the resulting “Motion Snapshot” is viewed on the
camera, the movie will play back in slow motion over approximately 2.5 s, followed by the still image; playback is accompanied by a background track about 10 s long.
Shooting in Motion Snapshot Mode
Select Motion Snapshot mode.
1
Rotate the mode dial to z.
9
Availabl e Settings
A
For information on the options available in Motion Snapshot mode, see
page 53.
49
9
Frame the picture.
2
Compose the photograph with your
subject in the center of the frame.
Begin buffering.
3
Press the shutter-release button halfway to focus (0 23). An icon will be
displayed as the camera begins
recording footage to the memory
buffer.
Shoot.
4
Smoothly press the shutter-release
button the rest of the way down. The
camera will record a photograph,
together with about a second of
movie footage beginning before and
ending after the time the shutterrelease button was pressed. Note that
some time may be required. When
recording is complete, the photograph will be displayed for a few seconds.
50
Buffering
A
Buffering begins when the shutter-release button is pressed halfway
and ends after about 90 seconds or when the shutter-release button is
pressed all the way down.
Shutter-release
button pressed
halfway to focus
Shutter-release button
Buffering
pressed all the way
down
Shooting ends
❚❚ Choosing a Theme
To choose the background music for the
movie, press & and use the multi selector
and J button to choose from Beauty,Wave s, Relaxation, and Tenderness.
& button
To play the background music for the
highlighted theme, press the $ button and use the W control to adjust volume.
9
$ button
Motion Snapshot Mode
A
Live audio is not recorded. Movies can not be recorded using the
movie-record button and the flash can not be used.
51
Viewing Motion Snapshots
Press K and use the multi selector to
display a Motion Snapshot (0 25;
Motion Snapshots are indicated by a z
icon). Pressing J when a Motion Snap-
shot is displayed plays back the movie
portion in slow motion over a period of
about 2.5 s, followed by the photo; the
background track plays for about 10 s.
To end playback and return to shooting
mode, press the shutter-release button
halfway.
Deleting Motion Snapshots
To delete the current Motion Snapshot,
press O. A confirmation dialog will be
displayed; press O again to delete the
9
photo and movie and return to playback, or press K to exit without deleting
the file. Note that once deleted, MotionSnapshots can not be recovered.
K button
O button
52
Available Settings
7
The following table lists the settings that can be adjusted in each
mode.
❚❚ C Auto Photo, y Smart Photo Selector, 1 Movie, and z Motion Snap-
1 Scene auto selector is available only in Motion Snapshot mode.
2 RAW images fixed at 3872 × 2592.
3 Electronic (Hi) is not available.
4 Slow motion selected in movie mode.
5 HD movie selected in movie mode.
6 VR lenses only.
—— ✔✔✔——✔✔✔—
PSAM h P S A M
7
54
❚❚ w Creative Mode
In the table below, creative modes are represented by the
following icons: j night landscape, o night portrait,
m backlighting, p easy panorama, q soft, r miniature effect,
and s selective color.
P, S, A, M
j o m p q r sPSAM
Exposure mode✔✔1✔1✔1———————
Image quality✔✔✔✔✔
Image size✔3✔3✔3✔3✔✔✔✔✔✔✔
Continuous✔✔✔✔———————
Frame rate— — — ————————
Movie settings— — — — ———————
Metering✔
White balance✔✔✔✔———————
ISO sensitivity✔
4✔4✔4✔4
4✔4✔4✔4
Picture Control✔✔✔✔———————
Custom Picture
Shooting menu
Control
✔✔✔✔———————
Color space✔ ✔ ✔ ✔ ✔✔✔✔✔✔✔
HDR— — — — — — ✔ ————
Active D-Lighting✔✔✔✔———————
Long exposure NR✔
High ISO noise
reduction
1 P Programmed auto is selected automatically when Electronic (Hi) is
selected for Cont inuous.
2 NEF (RAW) and NEF (RAW) + JPEG fine not available.
3 RAW images fixed at 3872 × 2592.
4 Not available when Electronic (Hi) is selected for Conti nuous.
5 VR lenses only.
6 Not available if a frame rate of 10 fps is chosen when Electronic (Hi) is
selected for Cont inuous.
7 Available only when built-in flash unit is raised.
8 Not available when HDR is on.
7
56
More on Photography
t
Self-Timer and Remote Control Modes
The self-timer and optional ML-L3 remote control (0 166) can be
used to reduce camera shake or for self-portraits. The following
options are available:
Off
c 10 sThe shutter is released 2, 5, or 10 seconds after the
b 5s
a 2s
Delayed
"
remote
Quick-response
#
remote
Before Using the Remote Cont rol
A
Before using the remote control for the first time, remove the clear plastic battery-insulator sheet.
Mount the camera on a tripod.
1
Mount the camera on a tripod or place the camera on a stable, level surface.
Display self-timer options.
2
Press 4 (E) to display self-timer
options.
Self-timer and remote control off. The shutter is
released when the camera shutter-release button is
pressed.
shutter-release button is pressed all the way down.
Choose 2s to reduce camera shake, 5s or 10 s for
self-portraits.
The shutter is released 2 s after the shutter-release
button on the optional ML-L3 remote control is
pressed.
The shutter is released when the shutter-release button on the optional ML-L3 remote control is pressed.
t
57
t
Select the desired option.
3
Use the multi selector to highlight the
desired option and press J.
Frame the photograph and shoot.
4
Self-timer mode: Press the shutterrelease button halfway to focus, and
then press the button the rest of the
way down. The self-timer lamp will
start to flash and a beep will begin to
sound. Two seconds before the photo
is taken, the lamp will stop flashing
and the beeping will become more
rapid.
Remote control mode: Aim the ML-L3 at
the infrared receiver on the camera
(0 2) and press the ML-L3 shutterrelease button (stand at a distance of
5m/16ft or less). In delayed remote
mode, the self-timer lamp will light for
about two seconds before the shutter is released. In quickresponse remote mode, the self-timer lamp will flash after the
shutter has been released.
58
Note that the timer may not start or a photograph may not be
taken if the camera is unable to focus or in other situations in
which the shutter can not be released. Turning the camera off
cancels self-timer and remote control modes. Remote control
modes are cancelled automatically if no operations are performed
for about five minutes after the mode is selected in Step 3.
Movie Mode
A
In self-timer mode, start and stop the timer by pressing the movierecord button instead of the shutter-release button. In remote control
mode, the ML-L3 shutter-release button functions as the movie-record
button.
Using the Built-in Flash
A
Slide the flash pop-up control to raise the flash before shooting. Shooting will be interrupted if the flash is raised while the self-timer or
delayed-remote timer is counting down.
In remote control mode, the flash starts charging while the camera is
waiting for the signal from the remote. The camera will only respond to
the shutter-release button on the remote control when the flash is
charged. If red-eye reduction (0 62) is used in quick-response remote
mode, the shutter will be released about one second after the red-eye
reduction lamp lights. In delayed remote mode, there will be about a
two second delay after the shutter-release button on the remote control is pressed; the red-eye reduction lamp will then light for about one
second before the shutter is released.
Tripod Mounting Spacer
A
Use an optional TA-N100 tripod adapter to prevent larger lenses coming into contact with the tripod head when the camera is mounted on
a tripod (0 167).
See Also
A
For information on choosing how long the camera will wait for a signal
from the remote, see page 160. See page 159 for information on controlling the beeps that sound when the self-timer or remote control is
used.
t
59
Exposure Compensation
Exposure compensation is used to alter exposure from the value
suggested by the camera, making pictures brighter or darker.
Choose from values between –3 EV (underexposure) and +3 EV
(overexposure) in increments of
make the image brighter while negative values make it darker.
1
/
3 EV. In general, positive values
–1 EVNo exposure
Display exposure compensation options.
1
Press 2 (E) to display exposure com-
pensation options.
t
Choose a value.
2
Use the multi selector to choose the
desired value.
Normal exposure can be restored by setting exposure compensation to ±0. Exposure compensation is not reset when the camera is turned off.
60
compensation
+1 EV
Exposure Compensation
A
Exposure compensation is most effective when used with centerweighted or spot metering (0 124).
The Built-in Flash
A
When used with the built-in flash, exposure compensation affects both
background exposure and flash level.
t
61
The Built-in Flash
To use the flash, raise it by sliding the
flash pop-up control. Charging begins
when the flash is raised; once charging is
complete, a flash-ready indicator (I) will
be displayed when the shutter-release
button is pressed halfway. The following
flash modes are available; choose a flash
mode as described on the following
page.
Flash pop -up control
NFill flash
NY Red-eye reduction
NYp
t
Np Fill flash + slow sync
Nr
Nq Rear-curtain sync
62
Red-eye reduction +
slow sync
Rear curtain +
slow sync
The flash fires with every shot. Use when
the subject is poorly lit or with back-lit subjects to “fill in” (illuminate) shadows.
The red-eye reduction lamp lights before
the flash fires, reducing “red-eye” caused
by light reflecting from your subject's retinas.
Combines red-eye reduction with slow
shutter speeds to capture background
details at night or under low light. Use for
portraits taken against a backdrop of night
scenery.
Combines fill flash with slow shutter
speeds to capture details of poorly-lit
backgrounds.
Combines rear-curtain sync (see below)
with slow shutter speeds to capture
poorly-lit background details.
While in other modes the flash fires as the
shutter opens, in rear-curtain sync the
flash fires just before the shutter closes,
creating streams of light that appear to follow moving light sources.
Choosing a Flash Mode
Display the flash mode options.
1
Press the multi selector down to display a list of flash modes. The modes
available depend on the shooting or
exposure mode.
Use the multi selector to highlight a
flash mode (0 62) and press J to
select.
t
63
Lowering the Built-in Flash
A
To save power when the flash is not in use,
press it gently downward until the latch
clicks into place. Do not use force. Failu re to
observe this precaution could result in product malfunction.
Using the Built-in Flash
A
The built-in flash can be used in auto photo mode and when P, S, A, M,
Night portrait, Backlighting, Soft, Miniature effect, or Selective
color is selected in creative mode (0 53). If the flash is fired multiple
times in quick succession, the flash and shutter may be temporarily disabled to protect the flash. Shooting can be resumed after a brief pause.
Objects close to the camera may be overexposed in photographs taken
with the flash at high ISO sensitivities.
To avoid vignetting, remove lens hoods and shoot at ranges of at least
0.6 m (2 ft). Some lenses may cause vignetting at greater distances or
obstruct the red-eye reduction lamp, interfering with red-eye reduction. The following illustrations show the effect of vignetting caused by
shadows cast by the lens when the built-in flash is used.
t
ShadowShadow
See Also
A
For information on adjusting the flash level, see “Flash Compensation”
(0 153).
64
Aperture, Sensitivity, and Flash Range
A
Flash range varies with sensitivity (ISO equivalency) and aperture. With
the standard zoom lens at maximum aperture and ISO sensitivity set to
ISO 100 to 3200, the range is approximately 0.6 m–5.0 m (2 ft–16 ft)
when the lens is zoomed all the way out, 0.6 m–3.0 m (2 ft–9.8 ft) at
maximum zoom.
t
65
t
66
More on Playback
I
Photo Information
Photo information is superimposed on
images displayed in full-frame playback
(0 25). Press the $ button to cycle
through simple photo information,
detailed photo information (0 68), and
no photo information.
6 File name ........................................... 120
Thumbnail Playback
A
Press $ to view or hide ratings (0 74) when thumbnails are displayed (0 70). In four- and nine-frame playback, protect status (0 100)
and frame numbers are also displayed.
5
10
4
9
6
7
8
7 Time of recording ......................18, 162
8 Date of recording....................... 18, 162
Camera histograms are intended only as a guide and may differ from
those in imaging applications. Sample histograms are shown below:
• If brightness varies evenly across the
image, the distribution of tones
will be relatively even.
• If the image is dark, tone distribu-
tion will be shifted to the left.
• If the image is bright, tone distribu-
tion will be shifted to the right.
Exposure compensation shifts the distribution of tones to the right
when raised, to the left when lowered. Histograms can give you a
rough idea of overall exposure when bright ambient lighting makes it
difficult to see the display in the monitor.
I
69
Thumbnail Playback
To view pictures in “contact sheets” of
four, nine, or 72 images, press W down
when a picture is displayed full frame.
W control
Full- frame
playback
Thumbnail playback
The following operations can be performed:
ToUseDescription
Display more
Display fewer
I
Highlight images
View highlighted
Delete highlighted
Rate highlighted
images
images
image
image
image
Press down to increase the number of
images displayed, up to decrease. Press
down when 72 images are displayed to view
W
images taken on selected dates (
Press up when four images are displayed to
view the highlighted image full frame.
/
Use the multi selector to highlight images.
You ca n d elete (0 73) or rate (0 74) the
highlighted image or zoom in for a closer
look (0 72).
Press J to view the highlighted image full
J
frame.
See page 73.
O
See page 74.
&
70
Calendar
playback
0
71).
Calendar Playback
To view pictures taken on a selected date,
press W down when 72 pictures are displayed (0 70).
W control
Full-f rame
playback
Thumbnail playback
The following operations can be performed:
ToUseDescription
/
Highlight date
View pictures taken
on highlighted date
Delete pictures taken
on highlighted date
Exit to thumbnail
display
Use multi selector to highlight date.
Press J to view the first picture
J
taken on the highlighted date.
Press O to delete all pictures taken on
O
the highlighted date.
Press W up to return to 72-frame dis-
W
play.
Calendar playback
I
71
Playback Zoom
To zoom in on a photograph, display it
full frame and press W up. Playback zoom
is not available with movies or Motion
Snapshots.
The following operations can be performed:
ToUseDescription
Press up to zoom in,
Zoom in o r
out
View ot her
areas of
image
View faces
I
Exit zoom
down to zoom out.
W
Whenever you zoom in
or out, a navigation window will appear with the
area currently visible in
the display indicated by
a yellow border. Press 1, 2, 3, or 4 to scroll the
image (keep pressed to scroll rapidly to other areas
of the frame).
Faces (up to five) detected
during face-priority AF
are indicated by white
borders in the navigation
window. Rotate the multi
selector to view other
faces.
Return to full-frame playback.
J
W control
72
Deleting Pictures
Pictures can be deleted from the memory card as described
below. Note that once deleted, pictures can not be recovered;
protected images, however, will not be deleted.
Deleting the Current Picture
To delete the picture currently displayed
in full-frame playback or selected in the
thumbnail list, press O. A confirmation
dialog will be displayed; press O again to
delete the picture and return to playback,
or press K to exit without deleting the
picture.
O button
The Playback Menu
To delete multiple images, press the G button, select Delete
in the playback menu, and choose from the options below. A
confirmation dialog will be displayed; select Ye s to delete the
images (note that some time may be required if a large number
of images is selected).
Delete selected images
Select images by date
Delete all imagesDelete all pictures on the memory card.
DiscardDelete all pictures rated ) (discard; 0 74).
Highlight images and press 1 or 3 to select or
deselect (0 99). Press J to exit when the selection is complete.
Highlight dates and press 2 to select or deselect.
To view the pictures taken on the highlighted
date, press W down; hold W up to view the high-
lighted picture full frame or press W down again to
return to the date list. Press J to delete all pic-
tures taken on the selected dates.
I
73
Rating Pictures
Rate pictures or mark them as candidates for later deletion
(0 73). The Slide show option in the playback menu can be
used to display only pictures with a selected rating or ratings
(0 75). Ratings can also be viewed in ViewNX 2. Rating is not
available with protected images.
Select a picture.
1
Display a picture in full-frame playback or highlight it in the
thumbnail list.
Press &.
2
Press & and rotate the multi selector
to choose from ratings of zero to five
stars, or select ) to mark the picture
as a candidate for later deletion. The
rating is stored when you press J or
display another picture.
& button
I
74
Slide Shows
To view a slide show of the pictures on
the memory card, press the G button,
select Slide show in the playback menu,
and follow the steps below.
Select the type of image used in the show.
1
Highlight the desired option and press J.
All images Display all the images on the memory card.
Still images
MoviesDisplay movies only.
Motion
Snapshot
Select images
by date
Selected scene
By rating
Face pr iority
Display still images only. Images taken using Easy panorama will be displayed in panorama mode (0 34).
Display only the movie portion of Motion Snapshots.
The associated photographs are not displayed.
Display only images
recorded on a selected date.
A calendar will be displayed;
use the multi selector to
highlight a date.
Display only photos belonging to a specific scene.
Choose from iAuto, k
landscape
up
s
Display only images with a
selected rating or ratings
(0 74). A rating selection
dialog will be displayed; use
the multi selector to highlight ratings and press 2 to
select or deselect.
Display only images in which the camera has detected
a face (0 24).
, oNight portrait, m
, pEasy panorama, q
Selective color
Port rait, l
Soft, r
.
G button
Landscape, j
Backlighting, n
Miniature effect
Night
Close
, and
I
75
I
Adjust display times and choose a background track.
2
Adjust the following options:
Frame interval Choose how long each still image is displayed.
Choose how much of each movie is played back before
Movie playback
time
Audio
the next slide is displayed. Choose Same as frame
interval to display the next slide after the time
selected for Frame interval, No limit to play back the
entire movie before displaying the next slide.
Mute audio playback or
choose a slide show background track (to play the
highlighted background
track prior to selection, press
the $ button and use the
W control to adjust volume).
Select Movie sound tracks
to play only audio recorded
with movies; in this case, no
sound is played for still
images or Motion Snapshots.
$ button
76
Select Start.
3
Highlight Start and press J to start
the slide show.
The following operations can be performed while a slide
show is in progress:
ToUseDescription
Skip back/skip
ahead
Pause/resumeJPause the show. Press again to resume.
Adjust volumeW
Exit to playback
mode
Press 4 to return to the previous frame, 2
to skip to the next frame.
Press up to increase volume, down to
decrease.
End the show and return to playback
K
mode.
The options shown at right are displayed when the show ends. Select
Resume to restart or Exit to exit to the
playback menu.
I
77
I
78
Connections
t
Q
Installing the Supplied Software
Install the supplied software to copy pictures to your computer
for viewing and editing pictures and creating short movies.
Before installing the software, confirm that your system meets
the requirements on page 81.
Start the computer and insert the installer ViewNX 2/
1
Short Movie Creator CD.
WindowsMac OS
Double-click icon
Double-click
Welc ome icon
Select a language.
2
If the desired language is
not available, click RegionSelection to choose a different region and then
choose the desired language (region selection is
not available in the European release).
q Select region (if required)
w Select languagee Click Nex
on desktop
Q
79
Q
l
Start the installer.
3
Click Install and follow the
on-screen instructions.
Exit the installer.
4
Click Ye s (Windows) or OK (Mac OS) when installation is complete.
WindowsMac OS
Click YesClick OK
The following software is installed:
• ViewNX 2
• Short Movie Creator
• Apple QuickTime (Windows only)
Remove the installer CD from the CD-ROM drive.
5
Click Instal
80
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.