Transducers LF Loudspeaker (x2) LS.HPB15
Recone kit LS.HPB15K
Required Controller Complete Unit LSTDcontroller
Parameter cards 1a75a or 1a99a
Spare parts see separate parts list
Miscellaneous Front foam
Flying rail (optional)(x 3)
Rings for Flying rail
I.2. LS 2000 parts list
GROUP PART DESIGNATION PART NAME
Transducers LF Loudspeaker LS.HPB20 or LS.HPB20B [a]
Recone kit LS.HPB20K
Required Controller Complete Unit LSTDcontroller
Parameter cards 2b55a or 2b75a
Spare parts see separate parts list
Miscellaneous Front foam
Flying rail (optional)(x 3)
Rings for Flying rail
[a] HPBLS20 has been used on cabinets with serial numbers 1 to 327. HPBLS20B has been used since
Service Manual LS2000 LS1500
Release : 1 LSTDcontroller Parameter cards
Date : 02/12/2004
II.1. Read Before Starting Reconing an LS2000 loudspeaker
This note only concern HPBLS20Loudspeaker (up to serial number 327)
After having removed the old cone-coil assembly, please have a look on the part of the chassis around
the magnetic gap. If there is a metal ring (with silver aspect), you will have to proceed as follows :
1. Unfasten the 4 screws assembling the metal ri ng and th e b asket (use a Pozidriv #3 type
screwdriver).
2. Remove the metal ring.
3. Reassemble the basket to the magnet ic pa rt, using the provided 4 screws (BTR type) and t he
special Loctite type glue to avoi d po tential loosening. Tighten the screws as strongly as p ossib le.
DO NOT USE THE PREVIOUS SCREWS WHICH ARE TOO LONG AND COULD DAMAGE
THE CHASSIS.
Metal ring
II.2. Mounting the loudspeaker into the cabinet.
Speakers have to be mounted in a push-pull architecture. Speaker 1 is mounted in a conventionnal way
and speaker 2 is mounted upside down. Use the special dia 6 SUPERIX screws, with a n°4 allen, or a
n°30 torx screwdriver.
If your speakers are HPB LS20B type (since serial number 328), there must be a block on the cabinet in
order to be able to mount the speaker 1 (HPBLS20B are deeper than HPBLS20). All cabinets since sn
xxx are provided with such a block. To mount type B speaker on an old cabinet please contact the
factory.
Service Manual LS2000 LS1500
Release : 1 LSTDcontroller Parameter cards
Date : 02/12/2004
Each speaker has to be normally connected (r ed and ora nge wires on red terminals) but a polarity
invertion on the speaker 2 is required. This invertion is being made at the factory, directly on the LS
connection plate. Check that when excited threw the SPEAKON with a DC battery, both loudspeakers are
moving towards you.
Apply 8 volts RMS to the cabinet and sweep from 20Hz to 50Hz. Listen for obvious noises.
LSTDcontroller REFERENCE GUIDE
Signal Speakon Connector Wire
Speaker 1 Pin 1- Black
Speaker 1 Pin 1+ Red
Speaker 2 Pin 2- Orange
Speaker 2 Pin 2+ Grey
R102 R202 Metal
R103 R203 Metal
R104 R204 Metal
R105 R205 Metal
R106 R206 Metal
R108 R208 Metal
R109 R209 Metal
R110 R210 Metal
R111 R211 Metal
R112 R212 Metal
R113 R213 Metal
R114 R214 Metal
R115 R215 Metal
R116 R216 Metal
R118 R218 Metal
R119 R219 Metal
R120 R220 Metal
R121 R221 Metal