KM D Accessories
Solution-D
Elastic Suspensions
Elastic Suspension EA 2124 A mt
The EA 2124 A mt is able to accept microphones from 21 to 24 mm in diameter. It has a swivel mount with a 5/8"-27
female thread, plus a thread adapter to
connect to 1/2"- and 3/8" stands.
EA 2124 A mt ...... blk ........ Cat. No. 008433
Table and Floor Stands
Table Stand MF 2
Small table stand with brass base, very
sturdy. It has a black matte finish. The
bottom is fitted with a non-slip rubber
disk. The stand has a 1/2" threaded stud
for mounting the SG 21/17 mt, for example. The rubber shock mount between
the stud and the base serves to suppress structure-borne noise.
Ø 60 mm, Weight 340 g.
MF 2 ..................... blk ........ Cat. No. 007266
Table Stand MF 3
The MF 3 is a table stand with iron base,
1.6 kg in weight, 110 mm in diameter. It
has a black matte finish. The bottom is
fitted with a non-slip rubber disk. The
stand comes with a reversible stud and
an adapter for 1/2" and 3/8" threads.
MF 3 ..................... blk ........ Cat. No. 007321
Floor Stand MF 4
Floor stand with grey cast iron base. The
floor stand has a matte black finish and
rests on a non-skid rubber disk attached
to the bottom. A reversible stud and a
reducer for 1/2" and 3/8" threads are
also supplied. Weight 2.6 kg, Ø 160 mm.
MF 4 ..................... blk ........ Cat. No. 007337
Floor Stand MF 5
Floor stand with grey soft-touch powder
coating. It has a non-skid sound-absorbing rubber ring attached to the bottom.
The stand connection has a 3/8" thread.
Weight 2.7 kg, Ø 250 mm.
MF 5 ..................... gr ......... Cat. No. 008489
Vertical Bar MZEF 8060/8120
(Sennheiser)
The MZEF ... vertical bars are screwed
onto microphone stands (e.g. MF 4,
MF 5). They have a length of 600 or
1200 mm, with 3/8" threads. Ø 12 mm.
MZEF 8060 .......... nx ......... Cat. No. 502318
MZEF 8120 .......... nx ......... Cat. No. 502319
Stand Extensions STV 4/20/40/60
The STV... stand extensions are screwed
between microphone stands (for example MF 4, MF 5) and swivel mounts (for
example SG 21/17 mt).
Length 40, 200, 400 or 600 mm.
Ø 19 mm.
STV 4 .................... blk ........ Cat. No. 006190
STV 20 ................. blk ........ Cat. No. 006187
STV 40 ................. blk ........ Cat. No. 006188
STV 60 ................. blk ........ Cat. No. 006189
Meaning of the color codes on the following pages: blk - black, ni - nickel, gr - grey, nx - nextel black
2
Auditorium Hangers
Auditorium Hanger MNV 21 mt
The auditorium hanger adjusts the tilting angle of a microphone suspended by
its own cable. The MNV 21 consists of
the tilting clamp, suitable to hold a Neumann miniature microphone or KMR 81,
and a locking cable strain relief. Suitable
for cables with 4–5 mm diameter.
MNV 21 mt .......... blk ........ Cat. No. 006802
Auditorium Hanger MNV 87 (mt)
The auditorium hanger consists of a cable suspension and a rotating 1/2"
threaded stud, to connect to e. g. swivel
mounts. The stud is screwed into the
threaded coupling of the swivel mount.
Then the microphone can be tilted while
it is suspended from its own cable. Suitable for cables with 4–8 mm diameter.
MN V 87 ............... ni .......... Cat. No. 006804
MNV 87 mt .......... blk ........ Cat. No. 006806
Auditorium Hanger MNV 100
The MNV 100 auditorium hanger is used
to suspend a detached miniature microphone capsule freely from its interconnecting cable. The assembly can be rotated and tilted to any desired angle.
Suitable for cables with 3–3.5 mm diameter.
MN V 100 ............. blk ........ Cat. No. 006811
Stand Mounts and Miscellaneous Mechanical Adapters
Double Mount DS 120
The DS 120 has a 150 mm long support
bar with two movable 1/2" threaded
studs. Two microphones in their mounts
can be attached. Any space or angle between the microphones is freely adjustable. The DS 120 has a 5/8"-27 female
thread, plus a thread adapter to connect
to 1/2"- and 3/8" stands.
DS 120 ................. blk ........ Cat. No. 007343
Stand Mount SG 21 bk
Swivel mount with a plastic clamp for
miniature microphones. It has a 5/8"-27
female thread, plus a thread adapter to
connect to 1/2"- and 3/8" stands.
SG 21 bk ............... blk ........ Cat. No. 008613
Stand Mount MZGE 8000 (Sennheiser)
Stand mount to attach one KVG ... capsule extension to MZEF ... vertical bars.
MZGE 8000 .......... nx ......... Cat. No. 502324
Stand Mount MZGE 8002 (Sennheiser)
Stand mount to attach two KVG ... capsule extensions to MZEF ... vertical bars.
MZGE 8002 .......... nx ......... Cat. No. 502325
3
Stand Mounts and Miscellaneous Mechanical Adapters
Stand Mount SG 109
Swivel mount for detached miniature microphone capsules. It has a 3/8" thread.
SG 109 ................. blk ........ Cat. No. 008614
Swivel Joint SG 110 nx
The SG 110 nx swivel mount can be inserted between KK 1... capsules and the
KM D output stage. The capsule can then
be swiveled and orientated through
± 110°. In combination with an elastic
suspension and a table flange, a mechanically decoupled, unobtrusive setup can
be realised, e.g. for TV news announcers.
Length 60 mm, Ø 22 mm.
SG 110 nx ............ nx ......... Cat. No. 008611
Stand Mount SGE 100
Swivel mount for detached miniature microphone capsules. A rubber shock
mount suppresses structure-borne
noise. The swivel mount has an M 6
thread (6 mm). Attaching the swivel
mount to the MF 2 table stand, the
SGE 100 replaces the rubber shock
mount of the table stand.
SGE 100 ............... blk ........ Cat. No. 006742
Stereo Mount STH 100
Stereo mount with a swivel mount and
two holders, for two detached miniature
microphone capsules. Two stereo recording methods are then possible.
One holder enables the microphone setup according to the “ORTF Method”:
Two detached capsules are snapped into
the clamps at the end of the holder. The
distance between diaphragms is then
170 mm, with an angle of 110°.
The other pair of holders allows stereo
setups according to the “Coincidence
Method”: Capsules are installed acoustically at one point in space, however,
freely adjustable to any angle between
30° and 180°.
The swivel mount has a 5/8"-27 thread,
plus a thread adapter to connect to
1/2"- and 3/8" stands.
STH 100 ............... blk ........ Cat. No. 007315
Stereo Mount STH 120
The STH 120 stereo mount accepts two
detached miniature microphone capsules, parallel and one above the other
for MS stereo recordings. It is rotatable
and swivelable. The swivel mount has a
5/8"-27 thread, plus a thread adapter to
connect to 1/2"- and 3/8" stands.
STH 120 ............... blk ........ Cat. No. 008422
Popscreens
Pop screens provide excellent suppression of so-called pop noise,
such as “p” or “t”. They consist of a round, thin frame covered with
black gauze on both sides. A gooseneck of about 30 cm (12") in
Popscreen PS 15
The frame is 15 cm in diameter.
PS 15 .................... blk ........ Cat. No. 008472
4
length is mounted at the popshield. It will be attached to microphone stands by means of a clamp with a knurled screw.
Foam Windscreens
Close range sounds, wind, and fast movements of the microphone
boom, all may cause interfering noises. To avoid these unwanted
sounds, windscreen accessories are available. Typically, they are
made out of open-cell polyurethane foam. These windscreens do
not cause interfering resonances and do not influence the direc-
Windscreen WNS 100
Windscreen for KM miniature microphones. Wind noise attenuation 18 dB.
Attenuation at 15 kHz 2 dB. Ø 45 mm.
WNS 100 ............. black ...... Cat. No. 007323
WNS 100 ............. red ......... Cat. No. 007324
WNS 100 ............. green ..... Cat. No. 007325
WNS 100 ............. yellow ...Cat. No. 007326
WNS 100 ............. blue ....... Cat. No. 007327
WNS 100 ............. white ...... Cat. No. 007328
Windscreen WNS 120
Windscreen for the microphone
KM 120 (D) or the capsules AK 20/
KK 120. Wind noise attenuation 15 dB.
Attenuation at 15 kHz 2 dB. Ø 48 mm,
length 65 mm. Color black.
WNS 120 .............. blk ........ Cat. No. 008427
tional pattern. Only in the upper frequency range is the output level slightly attenuated. The wind noise attenuation was measured
without electrical filtering in a turbulent air stream traveling at
20 km/h, generated by a noiseless wind machine.
Windscreen WNS 110
Acoustically transparent wind and pop
protection for KM miniature microphones, with improved efficiency. Wind
noise attenuation 21 dB. Attenuation at
15 kHz 1 dB. Ø 45 mm, length 70 mm.
Color black.
WNS 110 .............. blk ........ Cat. No. 008535
Windscreen WS 100
Larger windscreen for KM miniature microphones. Wind noise attenuation
23 dB. Attenuation at 15 kHz approx.
4 dB. Ø 90 mm. Color black.
WS 100 ................ blk ........ Cat. No. 006751
Connecting Cables
Microphone Cable LC 4
The LC 4 connects detached capsules
KK 1.. with the KM D output stage.
Ø 3.5 mm, length 5 or 10 m.
LC 4 (5 m) ............ nx ......... Cat. No. 008606
LC 4 (10 m) .......... nx ......... Cat. No. 008607
Other cable lengths are available upon
request!
5
Capsule Extensions for Miniature Microphone System KM D
Any KVG ... capsule extension allows to use the KK 1... capsules
separated from the output stage without the need for additional
cables. The rigid part of the capsule extension is 8 mm in diameter.
Capsule Extension KVG 130 nx
The extended length of the KVG 130 nx
is approximately 300 mm.
KVG 130 nx ......... nx ......... Cat. No. 008608
Capsule Extension KVG 160 nx
The extended length of the KVG 160 nx
is approximately 600 mm.
KVG 160 nx ......... nx ......... Cat. No. 008609
At the capsule end, the swivel can be set through ± 110°. The
KVG ... are mounted with MZGE 8000 or 8002 on MZEF ... vertical
bars. Special lengths on request.
Capsule Extension KVG 1120 nx
The extended length of the KVG 1120 nx
is approximately 1200 mm.
KVG 1120 nx....... nx ......... Cat. No. 008610
Further Accessories for KM Miniature Microphone
Output Stage KM D (nx)
The KM D (nx) microphone output stage
is part of the modular KM D miniature
microphone system. Together with a
KK 1.. capsule head it constitutes a complete microphone of the KM D system.
Preset frequencies 44.1, 48 and 96 kHz,
other frequencies on demand.
Ø 22 mm, length 93 mm.
KM D (44.1 kHz) ....... ni ..... Cat. No. 008578
KM D nx (44.1 kHz) .. nx .... Cat. No. 008581
KM D (48 kHz) ........... ni .... Cat. No. 008579
KM D nx (48 kHz) ...... nx .... Cat. No. 008582
KM D (96 kHz) ........... ni ..... Cat. No. 008580
KM D nx (96 kHz) ...... nx .... Cat. No. 008583
Sound Diffraction Sphere SBK 130 A
The SBK 130 A sound diffraction sphere
slips onto the KM 130, KM 131 (D) and
KM 183 (D) pressure microphones.
While sounds coming from the front-half
space are emphasized by up to 2.5 dB
between 2 kHz and 10 kHz, sounds arriving from the rear-half space are attenuated by 2.5 dB max in the range above
5 kHz. Inner Ø 22 mm.
SBK 130 A, 22 mm blk ..... Cat. No. 008612
6
Capsule Heads for Miniature Microphone System KM D
KK... capsule heads are part of the variable miniature microphone
system. Together with the KM D (nx) output stage KK... capsule
Capsule Head KK 131 (nx)
KK 131 is a free-field equalized pressure
transducer. The sensitivity in the free
sound field is flat up to 20 kHz. In the
diffuse sound field there is a roll-off
above 5 kHz.
KK 131 ................. ni .......... Cat. No. 008591
KK 131 nx ............ nx ......... Cat. No. 008592
Capsule Head KK 143 (nx)
KK 143 is a pressure gradient transducer
with wide-angle cardioid characteristic.
Attenuation: 4 dB at 90°, 8 dB at 135°,
and 11 dB at 180°. The frequency response for sound sources within an angle of ± 90° (off axis) is parallel up to
12 kHz.
KK 143 ................. ni .......... Cat. No. 008593
KK 143 nx ............ nx ......... Cat. No. 008594
heads form a complete microphone. KK 131 and KM D (nx), for example, make up the KM 131 (nx).
Capsule Head KK 183 (nx)
KK 183 is a diffuse-field equalized pressure transducer with a free-field treble
boost (approx. 7 dB at 10 kHz). The frequency response in the diffuse sound
field is flat up to 10 kHz.
KK 183 ................. ni .......... Cat. No. 008566
KK 183 nx ............ nx ......... Cat. No. 008567
Capsule Head KK 184 (nx)
KK 184 is a pressure gradient transducer
with cardioid characteristic. The frequency curves are very even and parallel
to 0° sound incidence. In typical usage,
there is no coloration of sound over a
wide pickup angle.
KK 184 ................. ni .......... Cat. No. 008568
KK 184 nx ............ nx ......... Cat. No. 008569
Capsule Head KK 145 (nx)
KK 145 is a pressure gradient transducer
with cardioid characteristic just like the
KK 184. However, it has an acoustic
bass roll-off characteristic in the free
field and therefore suppresses interfering LF noise (wind, structure-borne
noise).
Since proximity effect is a natural feature of pressure gradient microphones,
the KK 145 appears to be optimized for a
flat frequency response at a recording
distance of approximately 15 cm (speech
cardioid).
KK 145 ................. ni ........... Cat. No.008595
KK 145 nx ............ nx .......... Cat. No.008596
Capsule Head KK 185 (nx)
KK 185 is a pressure gradient transducer
with a hypercardioid characteristic. Attenuation of sound incidence from the
side or rear is approximately 10 dB. Minimum sensitivity occurs at an angle of
about 120°.
KK 185 ................. ni .......... Cat. No. 008570
KK 185 nx ............ nx ......... Cat. No. 008571
7
Digital Microphone Interface and Power Supplies
Digital Microphone Interface DMI-2
Equipment that supports the new AES 42 standard can process the
output signals of Solution-D microphones directly. In all other cases, the DMI-2 digital microphone interface is used. The DMI-2 is a
separate, two-channel device which converts the AES 42 data format supplied by the microphone into an AES/EBU signal. An eightchannel version is under development.
The DMI-2 is operated via the Neumann RCS remote control software, which is installed on a desktop or laptop computer. The computer is connected to the DMI-2 via a USB port and a USB to
RS 485 interface converter. If a large number of microphones is
used, several DMI-2s can be cascaded. In this case, each digital microphone interface can be addressed individually.
In addition to a word clock input and output, the DMI-2 also has
an internal word clock generator. If no master word clock signal
(e.g. from a mixing console) is present at the input, the DMI-2 internal word clock is used automatically to synchronize the two microphone channels, and the signal is switched to the word clock
output.
External commands such as „On Air“ (red light) can be controlled
via a 9-pin user port.
2 channels,
Inputs: ..................................... XLR3F, AES 42
Outputs: ................... XLR3M, AES/EBU, 24 bit
Control bus: .................. RS485 via RJ 45 jack,
connection to the computer‘s
USB port via Neumann USB485
interface converter (included)
User Port: ..................................... 9-pin sub-D,
3 functions per channel
Synchronization: ..... AES 42/Mode 1 + Mode 2
Word clock input: ...................... BNC, 75 ohms
Word clock output: .................... BNC, 75 ohms
Selectable internal sampling rates:
44.1, 48, 88.2, 96, 176.4, 192 kHz
External Word clock: ....... 44.1, 48, 88.2, 96,
176.4, 192 kHz or AES 11 format
Indicators: .......................Data Valid (AES 42)
and Sync Locked (Mode 2)
for each channel,
Power On and Ext. Word Clock
Power supply: ................. 90-240 V, 50/60 Hz
Connection Kit AES/EBU
The Connection Kits serve to supply
power to digital microphones, which are
in accordance with the AES 42 standard.
The microphone audio signal is made
available at the Connection Kit output in
S/PDIF or AES/EBU format, depending
upon the model. The remote control and
synchronization capabilities of the
AES 42 standard cannot be used with
the Connection Kit; they are operable
only with the DMI-2.
Connection Kit AES/EBU ...... Cat. No. 008584
DMI-2 EU ............................. Cat. No. 008561
DMI-2 UK ............................ Cat. No. 008587
DMI-2 US ............................. Cat. No. 008588
Connection Kit S/PDIF
The Connection Kits serve to supply
power to digital microphones, which are
in accordance with the AES 42 standard.
The microphone audio signal is made
available at the Connection Kit output in
S/PDIF or AES/EBU format, depending
upon the model. The remote control and
synchronization capabilities of the
AES 42 standard cannot be used with
the Connection Kit; they are operable
only with the DMI-2.
Connection Kit S/PDIF ......... Cat. No. 008585
Georg Neumann GmbH • Ollenhauerstr. 98 • 13403 Berlin • Germany • Tel.: +49 (30) 417724-0 • Fax: +49 (30) 417724-50 • E-Mail: headoffice@neumann.com • Website: www.neumann.com
8
Errors excepted, subject to changes • Printed in Germany • Publ. 10/08 525899/A03
Loading...