Size:
2.73 Mb
Download

ProSafe Dual Band

Wireless-NAccess Point

WNDAP350 Reference

Manual

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134

202-10534-01November 2009 v1.1

© 2009 by NETGEAR, Inc. All rights reserved.

Technical Support

Please refer to the Resource CD that shipped with your product. If your product does not contain aResource CD, then refer to the support information card that shipped with your product. By registering your product athttp://www.netgear.com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades.

NETGEAR, INC. Support Information

Phone: 1-888-NETGEAR,for US & Canada only. For other countries, see the Warranty and Customer Support information on yourResource CD. If your product does not contain aResource CD, then see the Warranty and Customer Support Information card.

E-mail:support@netgear.com

North American NETGEAR website: http://www.netgear.com

Trademarks

NETGEAR, the NETGEAR logo, ProSafe, Smart Wizard, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, Windows NT and Vista are registered trademarks of Microsoft Corporation.Other brand and product names are registered trademarks or trademarks of their respective holders.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.

NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

Certificate of the Manufacturer/Importer

It is hereby certified that the ProSafe Dual Band Wireless-NAccessPoint WNDAP350 Reference Manual has been suppressed in accordance with the conditions set out in theBMPT-AmtsblVfg243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions.

The Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations.

Bestätigung des Herstellers/Importeurs

Es wird hiermit bestätigt, daß dasProSafe Dual Band Wireless-NAccess Point WNDAP350 gemäß der im BMPTAmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.

Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.

Voluntary Control Council for Interference (VCCI) Statement

This equipment is in the Class B category (information equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing

ii

v1.1, November 2009

Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas. When used near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.

Regulatory Compliance Information

This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-userto comply with the applicable requirements may result in unlawful operation and adverse action against theend-userby the applicable National regulatory authority.

NOTE: This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all options described in this user's guide may not be available in your version of the product.

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:

EN60950-1:2006 EN 50385:

EN 300 328 V1.7.1 (2006-10)

EN 301 893 V1.5.1: (2008-12)

EN 301 489-1V1.8.1(2008-04)

EN 301 489-17V1.3.2(2008-04)This is an indoor only device.

Europe – Declaration of Conformity in Languages of the European Community

Cesky [Czech]

NETGEAR Inc. tímto prohlašuje, že tento Radiolan je ve shode se základními

 

požadavky a dalšími p?íslušnými ustanoveními sm?rnice 1999/5/ES.

 

 

Dansk

Undertegnede NETGEAR Inc. erklærer herved, at følgende udstyr Radiolan overholder

[Danish]

de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

 

 

Deutsch

Hiermit erklärt NETGEAR Inc., dass sich das Gerät Radiolan in Übereinstimmung mit

[German]

den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der

 

Richtlinie 1999/5/EG befindet.

 

 

Eesti

Käesolevaga kinnitab NETGEAR Inc. seadme Radiolan vastavust direktiivi 1999/5/EÜ

[Estonian]

põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

 

 

English

Hereby, NETGEAR Inc., declares that this Radiolan is in compliance with the essential

 

requirements and other relevant provisions of Directive 1999/5/EC.

 

 

Español

Por medio de la presente NETGEAR Inc. declara que el Radiolan cumple con los

[Spanish]

requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la

 

Directiva 1999/5/CE.

 

 

iii

v1.1, November 2009

Ελληνική

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR Inc. ΔΗΛΩΝΕΙ ΟΤΙ Radiolan ΣΥΜΜΟΡΦΩΝΕΤΑΙ

[Greek]

ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ

 

ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

 

 

Français

Par la présente NETGEAR Inc. déclare que l'appareil Radiolan est conforme aux

[French]

exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

 

 

Italiano [Italian]

Con la presente NETGEAR Inc. dichiara che questo Radiolan è conforme ai requisiti

 

essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

 

 

Latviski

Ar šo NETGEAR Inc. deklarē, ka Radiolan atbilst Direktīvas 1999/5/EK būtiskajām

[Latvian]

prasībām un citiem ar to saistītajiem noteikumiem.

 

 

Lietuvių

Šiuo NETGEAR Inc. deklaruoja, kad šis Radiolan atitinka esminius reikalavimus ir kitas

[Lithuanian]

1999/5/EB Direktyvos nuostatas.

 

 

Nederlands

Hierbij verklaart NETGEAR Inc. dat het toestel Radiolan in overeenstemming is met de

[Dutch]

essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

 

 

Malti [Maltese]

Hawnhekk, NETGEAR Inc., jiddikjara li dan Radiolan jikkonformamal-htigijiet

 

essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva1999/5/EC.

 

 

Magyar

Alulírott, NETGEAR Inc. nyilatkozom, hogy a Radiolan megfelel a vonatkozó alapvetõ

[Hungarian]

követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

 

 

Polski [Polish]

Niniejszym NETGEAR Inc. oświadcza, że Radiolan jest zgodny z zasadniczymi

 

wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

 

 

Português

NETGEAR Inc. declara que este Radiolan está conforme com os requisitos essenciais

[Portuguese]

e outras disposições da Directiva 1999/5/CE.

 

 

Slovensko

NETGEAR Inc. izjavlja, da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi

[Slovenian]

relevantnimi določili direktive 1999/5/ES.

 

 

Slovensky

NETGEAR Inc. týmto vyhlasuje, že Radiolan spĺňa základné požiadavky a všetky

[Slovak]

príslušné ustanovenia Smernice 1999/5/ES.

 

 

Suomi

NETGEAR Inc. vakuuttaa täten että Radiolan tyyppinen laite on direktiivin 1999/5/EY

[Finnish]

oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

 

 

Svenska

Härmed intygar NETGEAR Inc. att denna Radiolan står I överensstämmelse med de

[Swedish]

väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv

 

1999/5/EG.

 

 

Íslenska

Hér með lýsir NETGEAR Inc. yfir því að Radiolan er í samræmi við grunnkröfur og aðrar

[Icelandic]

kröfur, sem gerðar eru í tilskipun 1999/5/EC.

 

 

Norsk

NETGEAR Inc. erklærer herved at utstyretRadiolan er i samsvar med de

[Norwegian]

grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

 

 

iv

v1.1, November 2009

FCC Requirements for Operation in the United States

FCC Information to User

This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.

FCC Guidelines for Human Exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 25 cm between the radiator and your body.

This transmitter must not be co-locatedor operating in conjunction with any other antenna or transmitter.

FCC Declaration Of Conformity

We NETGEAR, Inc.,350 east Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the model ProSafe Dual Band Wireless-NAccess Point WNDAP350 complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause undesired operation.

FCC Radio Frequency Interference Warnings & Instructions

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and the receiver

Connect the equipment into an electrical outlet on a circuit different from that which the receiver is connected

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm between the radiator & your body.

v

v1.1, November 2009

This transmitter must not be co-locatedor operating in conjunction with any other antenna or transmitter.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.

Industry Canada statements

This device complies with RSS-210of the Industry Canada Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm between the radiator & your body.

This device has been designed to operate with an antenna having a maximum gain of 5 dBi Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

Caution:

The device for the band 5150-5250MHz is only for indoor usage to reduce potentail for harmful interference to cochannel mobile satellite systems.

High power radars are allocated as primary users (meaning they have priority ) of 5250-5350MHz and5650-5850MHz and these radars could cause interference and/or damage toLE-LANdevices.

Canada ID: 4054A-09200110

Product and Publication Details

Model Number:

WNDAP350

Publication Date:

November 2009

Product Family:

Wireless Access Point

Product Name:

ProSafe Dual Band Wireless-NAccess Point WNDAP350

Home or Business Product:

Business

Language:

English

Publication Part Number:

202-10534-01

Publication Version Number:

1.1

vi

v1.1, November 2009

Contents

ProSafe Dual Band Wireless-NWNDAP350 Reference Manual

About This Manual

Chapter 1

Introduction

About the ProSafe Dual Band Wireless-N Access Point WNDAP350

............................1-1

Key Features and Standards ..........................................................................................

1-1

Compatible and Related NETGEAR Products ................................................................

1-5

System Requirements ....................................................................................................

1-6

What’s In the Box? .........................................................................................................

1-6

Hardware Description .....................................................................................................

1-7

Chapter 2

 

Basic Installation and Configuration

 

Wireless Equipment Placement and Range Guidelines .................................................

2-2

Understanding WNDAP350 Wireless Security Options ..................................................

2-3

Installing the WNDAP350 wirelss access point ..............................................................

2-4

Logging In Using the Default IP Address ......................................................................

2-12

Setting Basic IP Options ...............................................................................................

2-13

Wireless Settings ..........................................................................................................

2-14

Setting Up and Testing Basic Wireless Connectivity ....................................................

2-22

Understanding Security Profiles ...................................................................................

2-23

SSID and WEP/WPA Settings Setup Form ..................................................................

2-27

Configuring the RADIUS Server Settings .....................................................................

2-29

Setting up a Security Profile .........................................................................................

2-31

Configuring WEP ..........................................................................................................

2-33

Configuring WPA with RADIUS ....................................................................................

2-35

Configuring WPA2 with RADIUS ..................................................................................

2-37

Configuring WPA and WPA2 with RADIUS ..................................................................

2-38

Configuring WPA-PSK ..................................................................................................

2-40

Configuring WPA2-PSK ................................................................................................

2-41

vii

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Configuring WPA-PSK and WPA2-PSK ........................................................................

2-42

Restricting Wireless Access by MAC Address .............................................................

2-44

Chapter 3

 

Management

 

Remote Management .....................................................................................................

3-1

Remote Console .............................................................................................................

3-3

Upgrading the Wireless Access Point Software .............................................................

3-5

Configuration File Management .....................................................................................

3-6

Changing the Administrator Password .........................................................................

3-10

Enabling the SysLog Server .........................................................................................

3-11

Using Activity Log Information ......................................................................................

3-12

Viewing General Summary Information ........................................................................

3-12

Viewing Network Traffic Statistics .................................................................................

3-14

Viewing Available Wireless Station Statistics ................................................................

3-16

Enabling Rogue AP Detection ......................................................................................

3-17

Viewing Rogue AP Statistics ........................................................................................

3-19

Packet Capture .............................................................................................................

3-21

Chapter 4

 

Advanced Configuration

 

IP Settings for Wireless Clients ......................................................................................

4-1

Hotspot Settings .............................................................................................................

4-3

Configuring Advanced Wireless Settings .......................................................................

4-4

Configuring Advanced QoS Settings ..............................................................................

4-8

Enabling Wireless Bridging ...........................................................................................

4-10

Chapter 5

 

Troubleshooting and Debugging

 

No lights are lit on the wireless access point. .................................................................

5-1

The Wireless LAN activity light does not light up. ...........................................................

5-2

The LAN light is not lit. ....................................................................................................

5-2

I cannot access the Internet or the LAN with a wireless capable computer. .................5-2

I cannot connect to the WNDAP350 to configure it. .......................................................

5-3

When I enter a URL or IP address I get a timeout error. ................................................

5-3

Using the Reset Button to Restore Factory Default Settings ..........................................

5-4

viii

Contents

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Appendix A

Default Settings and Technical Specifications

Factory Default Settings ................................................................................................

A-1

Technical Specifications .................................................................................................

A-3

Appendix B

 

Related Documents

 

Appendix C

 

Command Line Reference

 

Command Sets ..............................................................................................................

C-1

Index

 

Contents

ix

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

x

Contents

v1.1, November 2009

About This Manual

The ProSafe™ Dual BandWireless-NAccess Point WNDAP350 Reference Manualdescribes how to install, configure and troubleshoot the ProSafe Dual Band Wireless-N Access Point WNDAP350. The information in this manual is intended for readers with intermediate computer and Internet skills.

Conventions, Formats, and Scope

The conventions, formats, and scope of this manual are described in the following paragraphs:

Typographical Conventions. This manual uses the following typographical conventions:

Italic

Emphasis, books, CDs, file and server names, extensions

 

 

Bold

User input, IP addresses, GUI screen text

 

 

Fixed

Command prompt, CLI text, code

italic

URL links

 

 

Formats. This manual uses the following formats to highlight special messages:

Note: This format is used to highlight information of importance or special interest.

Tip: This format is used to highlight a procedure that will save time or resources.

Warning: Ignoring this type of note may result in a malfunction or damage to the equipment.

xi

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Danger: This is a safety warning. Failure to take heed of this notice may result in personal injury or death.

Scope. This manual is written for the WNDAP350 wirelss access point according to these specifications:

Product Version

ProSafe Dual Band Wireless-NAccess Point WNDAP350

 

 

Manual Publication Date

November 2009

 

 

For more information about network, Internet, firewall, and VPN technologies, see the links to the NETGEAR website in Appendix B, “Related Documents.”

Note: Product updates are available on the NETGEAR, Inc. website at

http://kbserver.netgear.com/products/WNDAP350.asp.

How to Print This Manual

To print this manual, your computer must have the free Adobe Acrobat reader installed in order to view and print PDF files. The Acrobat reader is available on the Adobe Web site at http://www.adobe.com.

Tip: If your printer supports printing two pages on a single sheet of paper, you can save paper and printer ink by selecting this feature.

Revision History

Part Number

Version

Date

Description

 

Number

 

 

 

202-10534-01

1.0

September

Product introduction

 

 

2009

 

 

202-10534-01

1.1

November

Updated FCC statement

 

 

2009

 

 

 

 

 

 

 

xii

 

 

About This Manual

v1.1, November 2009

Chapter 1

Introduction

This chapter describes some of the key features of the ProSafe Dual Band Wireless-NAccess Point WNDAP350. It also includes the minimum prerequisites for installation (“System Requirements” on page 1-5.),package contents (“What’s In the Box?” on page 1-6)and a description of the front and back panels of the WNDAP350 (“Hardware Description” on page 1-6).

About the ProSafe Dual Band Wireless-NAccess Point

WNDAP350

The ProSafe Dual Band Wireless-NAccess Point WNDAP350is the basic building block of a wireless LAN infrastructure. It provides connectivity between Ethernet wired networks and radioequipped wireless notebook systems, desktop systems, print servers, and other devices.

The WNDAP350 provides wireless connectivity to multiple wireless network devices within a fixed range or area of coverage, interacting with a wireless network interface card (NIC) via an antenna. Typically, an individual in-buildingaccess point provides a maximum connectivity area of about a 500 foot radius. Consequently, the ProSafe Dual BandWireless-NAccess Point WNDAP350 can support a small group of users in a range of several hundred feet. Most access points can handle between 10 to 32 users simultaneously per radio.

The WNDAP350 wirelss access point acts as a bridge between the wired LAN and wireless clients. Connecting multiple WNDAP350s via a wired Ethernet backbone can further lengthen the wireless network coverage. As a mobile computing device moves out of the range of one access point, it moves into the range of another. As a result, wireless clients can freely roam from one Access Point to another and still maintain seamless connection to the network.

Key Features and Standards

The WNDAP350 wirelss access point is easy-to-useand provides solid wireless and networking support. It also offers a wide range of security options.

1-1

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Supported Standards and Conventions

The following standards and conventions are supported:

Standards Compliance. The Wireless Access Point complies with the IEEE 802.11 a/b/g/n standards for Wireless LANs.

Full WPA and WPA2 support. WPA and WPA2enterprise-classstrong security with RADIUS and certificate authentication as well as dynamic encryption key generation.WPAPSK andWPA2-PSKpreshared key authentication without the overhead of RADIUS servers but with all of the strong security of WPA.

Multiple BSSIDs. Supports multiple BSSIDs. When a wireless access point is connected to a wired network and a set of wireless stations, it is called a Basic Service Set (BSS). The Basic Service Set Identifier (BSSID) is a unique identifier attached to the header of packets sent over a WLAN that differentiates one WLAN from another when a mobile device tries to connect to the network.

The multiple BSSID feature allows you to configure up to 8 SSIDs per Radio mode on your access point and assign different configuration settings to each SSID. All the configured SSIDs are active and the network devices can connect to the access point by using any of these SSIDs.

DHCP Client Support. DHCP provides a dynamic IP address to PCs and other devices upon request. The WNDAP350 can act as a client and obtain information from your DHCP server; it can also act as a DHCP server and provide network information for wireless clients.

SNMP Support. Support for Simple Network Management Protocol (SNMP) Management Information Base (MIB) management.

802.1Q VLAN (Virtual LAN) Support. A network of computers that behave as if they are connected to the same network even though they actually may be physically located on different segments of a LAN. VLANs are configured through software rather than hardware, which makes them extremely flexible. VLANs are very useful for user/host management, bandwidth allocation and resource optimization.

Key Features

The WNDAP350 provides solid functionality, including the following features:

Dual Band Concurrent. The Wireless Access Point can operate in both the 2.4 GHz band and the 5 GHz band concurrently.

The choice of band(s) is reflected in the protocol standard supported, as well as the administration screens displayed to you.

1-2

Introduction

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Multiple operating modes:

Wireless Access Point. Operates as a standard 802.11a/an or 11b/bg/ng access point.

Point-to-Point Bridge. In this mode, the WNDAP350 only communicates with anotherbridge-modewireless access point (with or without clients). Network authentication should be used to protect this communication.

Point-to-Multi-Point Bridge. Select this only if this WNDAP350 is the “Master” for a group ofbridge-modewireless access points. The otherbridge-modewireless access points send all traffic to this “Master”, and do not communicate directly with each other. Network Authentication should be used to protect this traffic.

Hotspot Settings. You can allow the first HTTP (TCP, port 80) request, on client association, to be captured and redirected to the URL you specify.

Upgradeable Firmware. Firmware is stored in a flash memory and can be upgraded easily, using only your Web browser, and can be upgraded remotely. In addition to using Web browser to do so,command-lineinterface and SNMP can also be used.

Rogue AP detection. The Rogue AP detection feature shows a list of unknown APs to the administrator.

Access Control. The Access Control MAC address filtering feature can ensure that only trusted wireless stations can use the WNDAP350 to gain access to your LAN.

Security Profiles. When using multiple BSSIDs, you can configure unique security settings (encryption, SSID, etc.) for each BSSID.

Hidden Mode. The SSID is not broadcast, assuring only clients configured with the correct SSID can connect.

Secure Telnet Command Line Interface. The secure Telnet command line interface enables direct secure access over the serial port and easy scripting of configuration of multiple WNDAP350s across an extensive network via the Ethernet interface. An SSH client is required.

Configuration Backup. Configuration settings can be backed up to a file and restored.

Power over Ethernet. Power can be supplied to the WNDAP350 over the Ethernet port from any 802.3af compliantmid-spanorend-spansource. Please refer to the Appendix for a list of compliant Netgear PoE switches.

Autosensing Ethernet Connection with Auto Uplink Interface.Connects to 10/100/1000 Mbps IEEE 802.3 Ethernet networks.

LED Indicators. Power/Test, LAN speed, LAN activity, and wireless activity for each radio mode are easily identified.

Introduction

1-3

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Wireless Multimedia (WMM) Support. WMM is a subset of the 802.11e standard. WMM allows wireless traffic to have a range of priorities, depending on the kind of data. Timedependent information, like video or audio, has a higher priority than normal traffic. For WMM to function correctly, Wireless clients must also support WMM.

WMM Power Save Support. Power Save uses mechanisms from 802.11e and legacy 802.11 to save power (for battery powered equipment) andfine-tunepower consumption.

VLAN Security Profiles. Each Security Profile can be assigned a VLAN ID as each Security Profile is modified.

802.11a/b/g/n Standards-basedWireless Networking

The ProSafe Dual Band Wireless-NAccess Point WNDAP350 provides a bridge between Ethernet wired LANs and 802.11a/b/g/n compatible wireless LAN networks. It provides connectivity between Ethernet wired networks andradio-equippedwireless notebook systems, desktop systems, print servers, and other devices. Additionally, the WNDAP350 supports the following wireless features:

Aggregation Support

Reduced Inter Frame Spacing support

Multiple Input, Multiple Output (MIMO) support

Distributed coordinated function (CSMA/CA, Back off procedure, ACK procedure, retransmission of unacknowledged frames)

RTS/CTS handshake

Beacon generation

Packet fragmentation and reassembly

Auto or long preamble

Roaming among access points on the same subnet

Autosensing Ethernet Connections with Auto Uplink

The WNDAP350 can connect to a standard Ethernet network. The LAN interface is autosensing and capable of full-duplexorhalf-duplexoperation.

The wireless access point incorporates Auto UplinkTM technology. The Ethernet port will automatically sense whether the Ethernet cable plugged into the port should have a “normal” connection such as to a computer or an “uplink” connection such as to a switch or hub. That port will then configure itself to the correct configuration. This feature also eliminates any concerns about crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection.

1-4

Introduction

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Compatible and Related NETGEAR Products

For a list of compatible products from other manufacturers, see the Wireless Ethernet Compatibility Alliance Web site (WECA, see http://www.wi-fi.net).

The following NETGEAR products work with the WNDAP350 wirelss access point:

FS108P - ProSafe 8 Port 10/100 Switch with 4 Port PoE

FS116P ProSafe 16 Port 10/100 Desktop Switch with 8 Port PoE

FS726TP - ProSafe 24 Port 10/100 Smart Switch with 2 Gigabit Ports and 12 Port PoE

FS728TP - ProSafe 24+4 10/100 Smart Switch with full PoE

FS752TPS - ProSafe 48 Port 10/100 Stackable Smart Switch with 4 Gigabit Ports and 24 Port PoE

FSM7328PS - ProSafe 24-port10/100 L3 Managed Stackable Switch with 24 PoE Ports

FSM7352PS

GS724TP

GS748TP

WNDA3100 - RangeMax Dual Band Wireless-NUSB 2.0 Adapter

WN121T RangeMax NEXT Wireless-NUSB 2.0 Adapter

WN111 - RangeMax Next Wireless-NUSB Adapter

WN511B RangeMax NEXT Wireless-NNotebook Adapter

WN311B RangeMax NEXT Wireless-NPCI Adapter

WAG511 ProSafe 108 Mbps Dual Band PC Card

WAG311 ProSafe 108 Mbps Dual Band PCI Card

WG311T 802.11g 108 Mbps Wireless PCI Card

WG511T 802.11g 108 Mbps Wireless CardBus Adapter

WG511 802.11g 54 Mbps Wireless CardBus Adapter

WG111 801.11g 54 Mbps Wireless USB Adapter

WPN111 - RangeMax Wireless USB 2.0 Adapter

System Requirements

Before installing the WNDAP350, make sure your system meets these requirements:

A 10/100/1000 Mbps Local Area Network device such as a hub or switch

Introduction

1-5

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

The Category 5 UTP straight through Ethernet cable with RJ-45connector included in the package, or one like it

A 100-240V,50-60Hz AC power source

A Web browser for configuration such as Microsoft Internet Explorer 5.0 or above, or Mozilla 3.0 or above

At least one computer with the TCP/IP protocol installed

802.11a/n or 802.11b/g/n-compliantdevices, such as the NETGEAR WG511 Wireless Adapter

What’s In the Box?

The product package should contain the following items:

ProSafe Dual Band Wireless-NAccess Point WNDAP350

Power adapter and cord (12 V dc, 1.2 A)

Straight through Category 5 Ethernet cable

ProSafe Dual Band Wireless N Access Point WNDAP350 Installation Guide

Resource CD which includes a link to this manual.

If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton, including the original packing materials, in case you need to return the firewall for repair. To qualify for product updates and product warranty registrations, we encourage you to register on the NETGEAR Web site at: http://www.NETGEAR.com.

Hardware Description

This section describes the front and rear hardware functions of the WNDAP350.

1-6

Introduction

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Front Panel

The WNDAP350 front hardware functions are described below.

1

2

3

4

5

Figure 1-1

The following table explains the LED indicators:

Table 1-1.Front Panel LED Indicators

Item

LED

DESCRIPTION

 

 

 

 

1

PWR/TEST

Power Indicator

 

 

 

 

 

 

Off

No power.

 

 

 

 

 

 

On

Power is on.

 

 

 

 

 

 

Blink

Indicates self test, loading software, or system fault (if continues).

 

 

 

Note: This LED may blink for a minute before going off.

 

 

 

 

2

100

 

Ethernet LAN Speed Indicator

 

 

 

 

 

 

Off

Indicates 10 Mbps or no link detected.

 

 

 

 

 

 

Yellow

Indicates 100 Mbps link detected.

 

 

 

 

 

 

Green

Indicates 1000 Mbps link detected.

 

 

 

 

3

LINK/ACT LAN

Ethernet LAN Link Activity Indicator

 

 

 

 

 

 

Off

Indicates no Ethernet link detected.

 

 

 

 

 

 

Blink

Indicates data traffic on the 1000Mbps Ethernet LAN.

 

 

(Green)

 

 

 

 

 

Introduction

1-7

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Table 1-1.Front Panel LED Indicators (continued)

Item

LED

DESCRIPTION

 

 

 

 

4

802.11na WLAN

Wireless LAN Link Activity Indicator (5 GHz)

 

 

 

 

 

 

Off

Indicates WLAN 802.11n/a (5GHz) mode is disabled.

 

 

 

 

 

 

Blink

Indicates Wireless data traffic in 5GHz modes.

 

 

(Green)

 

 

 

 

 

5

802.11ng WLAN

Wireless LAN Link Activity Indicator (5 GHz)

 

 

 

 

 

 

Off

Indicates WLAN 802.11b/g (5GHz) mode is disabled.

 

 

 

 

 

 

Blink

Indicates Wireless data traffic in 2.4GHz modes.

 

 

(Green)

 

 

 

 

 

Rear Panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

1

Figure 1-2

The WNDAP350 rear panel functions are described below:

1.Left and Right Detachable Antennas. The WNDAP350 provides two detachable dipole antennas.

2.Power Socket. This socket connects to the WNDAP350 12V 1.2A power adapter.

3.RJ-45Ethernet Port. Use the WNDAP350 EthernetRJ-45port to connect to an Ethernet LAN through a device such as a hub, switch, router, or PoE switch.

4.Serial Console Port. Male DB-9serial port for serial DTE connections.

5.Restore to Factory Defaults Button. The restore to default button restores the WNDAP350 to the factory default settings.

1-8

Introduction

v1.1, November 2009