Netgear WNDAP330, WNDAP350 Reference Manual

VLAN

2

VLAN

3

LAYER2/LAYER3 SWITCH

VLAN1:
Management IP 192.168.0.254
Port: 1/0/1, 1/0/6, 1/0/7-1/0/28 (Untagged)
VLAN 2:
Ports: 1/0/2, 1/0/3 (PVID = 2, Untagged), 1/0/6 (Tagged)
VLAN 3:
Ports: 1/0/4, 1/0/5 (PVID = 3, Untagged) , 1/0/6 (Tagged)

WNDAP330

Management VLAN = 1
Management IP = 192.168.0.235

SSID “VLAN2” (VLAN ID = 2), Open system None
SSID “VLAN3” (VLAN ID = 3), Open system None

LAN to 1/0/6

DGFV338 LAN to 1/0/2

Internet

DGFV338

LAN IP: 10.0.0.1/24
DHCP 10.0.0.0/24

1/0/4 to LAN

Corporate LAN

Layer 2 / Layer 3 switches and multi-SSID multi-VLAN network with traffic
separation

This document describes the steps to undertake in configuring a Layer 2/Layer 3 switch (in this
document a FMS7382S with firmware 7.3.1.7) and a WNDAP330 to host a multi-SSID and multi­VLAN network.

The solution will allow separating the Wireless traffic and Wired traffic of each of the VLANs
configured, from any other VLAN which will exist on the Wired or Wireless LAN.

The diagram below shows a typical scenario.

Version 1.0

Table of Contents

NETWORK SETUP .......................................................................................................... 3

Physical setup ............................................................................................................... 3

Logical setup ................................................................................................................. 3

LAYER2/LAYER3 SWITCH CONFIGURATION ......................................................... 4

Create a new VLAN ..................................................................................................... 4

Assign Port’s membership (to a VLAN) .................................................................... 4

Change the port PVID ................................................................................................. 4

Save the configuration ................................................................................................. 5

ACCESS POINT CONFIGURATION ............................................................................ 6

Enable the Wireless Radio mode and configure the Radio Channel ................... 6

Create a new SSID and assign a VLAN ID .............................................................. 6

Select the management VLAN and Untagged VLAN ............................................. 6

FURTHER NOTES........................................................................................................... 7

Testing ........................................................................................................................... 7

Managing devices ........................................................................................................ 7

Version 1.0

NETWORK SETUP

Physical setup
DGFV338 connected to port 1/0/2 on Layer2/Layer3 switch
Corporate LAN connected to port 1/0/4 on Layer2/Layer3 switch
WNDAP330 connected to port 1/0/6 on Layer2/Layer3 switch

Logical setup

DGFV338

DHCP: 10.0.0.0/24
WNDAP330
Management VLAN = 1

Untagged VLAN = 1
LAN management IP = 102.168.0.235
SSID VLAN2 (VLAN ID=2), Network authentication (Optional)
SSID VLAN3 (VLAN ID=3), Network authentication (Optional)

Layer2/Layer3 switch
Model: FSM7328S (or any Layer2, Layer3 switch)

Firmware: 7.3.1.7 (or above)
VLAN1
Management IP = 192.168.0.254
Ports = 1/0/1, 1/0/6-1/0/28 (All ports untagged)
VLAN2
Ports = 1/0/2, 1/0/3 (PVID = 2, Untagged), 1/0/6 (Tagged)
VLAN3
Ports = 1/0/4, 1/0/5 (PVID = 3, Untagged), 1/0/6 (Tagged)

LAN IP: 10.0.0.1/24

Version 1.0