NETGEAR ProSafe 10, ProSafe 100, ProSafe 1000 User Manual

Install the Switch

To install your switch on a flat suface, you do not need any special tools. Be sure the switch is positioned with at least 2 inches of space on all sides for ventilation.

To install the switch in a rack, first attach the mounting brackets to the side of the switch. Insert the screws provided in the rack mount kit through each bracket mounting hole in the switch. Tighten the screws with a #1 Phillips screwdriver to secure each bracket. AUgn the mounting holes in the brackets with the holes in the rack and insert two pan-head screws with nylon washers through each

bracket and into the rack. Tighten the screw with a #2 Phillips screwdriver to secure the switch in the rack.

Connect the Devices

To connect devices to the switch:

1. Connect the devices to the 10/100/1000 Mbps ports on the switch, using Category 5 UTP cable and an RJ-45 Plug.

Note: Ethernet specifications limit the cable length between your PC or server and the switch to 328 feet (100 meters) in

length.

2. Connect one end of the DC power adapter cable to the power outlet on the rear panel of the swith and other end of the power adapter cable to wall outlet.

NETGEAR'

NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 http://www.NETGEAR.com

NETGEAR*

JGS

ProSafe 10/100/1000 Switch W/SFP slots

Installation Guide

Trademarks

NETGEAR, ProSafe, and Auto Uplink are registered trademarks of NETGEAR, Inc in the United States and other countries. All other trademarks and registered trademarks are the property of dieir respective owners.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliabili^, NETGEAR reserves the right to make changes to the products to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or qiplication of the profuct(s) or circuit layout(s) described herein.

Certificate of the Manufacturer/Importer

By certified diat the NETGEAR Prosafe JGS524F Fast Ethernet Switch has been suppressed in accordance with the confitions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordace with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. Federal Office for Tdecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series fot compliance with the regulations.

Voluntary Control Council for Interference (VCCI) Statement

EN 55 022 Declaration of Conformance

This is to certify that the NETGEAR Prosafe JGSS24F Fast Ethernet Switch is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN3S 022 Class A (CISPR 22).

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

This device complies with part 15 of the FCC Rules. Opmation is subject to the followng two conditions:

• This device may not cause harmful interfemece.

• This device must accq>t any interfemce received, including intrfemce that may cause undesired operation. Note: This equipment has been tested and fotmd to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferences in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferences to radio communications. However, there is no guarantee that interference wiU not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct die interference by one or more of the following measures.

-Reorient or relocate the receiving antenna.

-hicrease the separation between die equipment and receiver.

-Connect die equipment into an outiet on a circuit different fixim diat to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications Radio inerference Reguiations

This digital apparatus (NETGEAR Prosafe JGS524F Fast Ethernet Switch ) does not exceed the Class A limits

for radio-noise emissions from digital apparatus as set out in the Radio rnterference Regulations o f the

ranndian Department of GfimnniniRatinna.

Céfiement sur ie brouillage radioélectrique du mimistére des Communications

Cet pareil numérique (NETGEAR Prosafe JGS524F Fast Ediemet Switch ) re^ecte les limites de bruits radioélectriques visant les appareils numériques de class A tpescrites dans le Reglement sur le brouillage radioélectrique du mimisére des Communications du Canada.

20 0521-

start Here

The NETGEAR® ProSafe JGS524F 24 Port 10/100/1000 Mbps Switch with 2 SFP slots provides you with a low-cost, high-

performance network solution and are designed to support power workgroups operating at either 10 megabits per second (Mbps) or With the ProSafe JGS524F 10/100/1000 Mbps Switch with optional SFP GBIC modules (AGM731F, AGM732F, AGM733),

improvement is accomplished very easily, with no change to the desktop (the network interface cards or software and the network wiring). As a result, the performance upgrade and the applications it enables are obtained very quickly and at a low cost.

Product Illustration

Front Panel of the ProSafe JGS524F Switch

10/100/1000 Mbps ports

Rear Panel of the ProSafe JGS524F Switch

AC Power out

^ЁЁЁшттЖ

LEDs

The table below describes the activity of the LEDs.

JЫЫЫЫЫlЙjЫЫЫЫC

Network Port -----------------

All ports on the switch are 10/100/1000 Mbps capable ports that auto negotiate for speed, and duplex. Additionally, all ports have Auto Uplink™ to make the right connection.

Auto Uplink™ The Auto Uplink technology that NETGEAR has included in this product wUl automatically sense whether the straight-through cable plugged into any port should have a 'normal' connection, e.g. connecting to a PC; or an 'uplink' connection, e.g. connecting to a router, switch, or hub. That port will then configure itself to the correct configuration. This feature also eliminates the need to worry about crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection.

Note: Auto Uplink will compensate for setting uplink connections, and crossover or straight-through cables. Using Auto Uplink to create

multiple paths between any two network devices will disable your network.

Applications

Desktop Switching

ProSafe JGS524F switch is used as a desktop switch to build a small network that enables users to have 1000 Mbps access to a file server. If a fiill-duplex adapter card is installed in the server or PC, a 2000Mbps connection is possible on the port where the server or PC is completed.

Label Color Activity

PWR (Power) Green On Power is suppiied to the Switch.

Off Power is disconnected.

Link / Activity Green (Port Number)

10/100/1OOOM

SFP

Orange Green

Green

Soiid Vaiid Link on the port. Biinking Packet transmission or receiving on the port.

On Off

On Biinking

Description

The port is operating in 1000 Mbps. The port is operating in 10 Mbps mode, if corresponding L/A LED

is Soiid or Biinking Vaiid Link on the port

Packet transmission or receiving on the port

SFP GBIC Module

The module bays accommodates standard SFP GBIC modules, such as the AGM73 IF or AGM732F fi'om NETGEAR, allowing you to have fiber connections on your network. The module bays are combo ports, sharing a connection with an RJ-45 port. Being a combo port, only one type of connection can be active at any given time. For example, both copper and fiber port cannot be used at the same time. If both connectors are plugged in at the same time, the fiber port will be active. The SFP GBIC bay accommodates a standard SFP GBIC module.

Installing an SFP GBIC Module

The following procedure describes how to install an SFP Gigabit Ethernet module in the switch's Gigabit module bay. Standard SFP GBIC modules are sold separately from the JGS524F. If you do not want to install an SFP GBIC module at this time, skip this procedure. To install an SFP GBIC module: o Insert the SFP module into the SFP module bay. Press firmly to ensure the module seats into the connector.

Note: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removig a transceiver.

However, always first disconnect the network eable before removing a transceiver.

Model JGS524F

100Mbps 10Mbps

Standards Compatibility

Date Rate 1000 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX

Network Interface Power 28.5W

Dimensions 328x43.2x169mm Weight 1.7kg/3.7 lbs Environmental Specifications

Operating temperature: 0to40”C(32to104”F) Operating humidity: 90% maximum relative humidity, noncondensing

Electromagnetic Compliance Safety Agency Approvals Performance Specifications

Queue buffer M1 Uh

IEEE 802.3110BASE-T Ethernet, IEEE 802.3 100BASE-FX Fast Ethernet. IEEE 802.3x Flow Control, IEEE 802.3ab lOOOBASE-TGigabit Ethernet, IEEE 802.3z 1000BASE-X Compatible with major network software, including Windows, NetWare, and Linux

10,100 or 1000 Mbps half-duplex/20 200 or 2000 Mbps full-duplex RJ-45 Maximum connector for 10BASE-T, 10OBASE-TX or 1000 BASE-T Ethernet interface

100-240VAC/50-60 Hz universal input

VCCI Class А/ FCC Class А/ СЕ/ C-tick UL/CUL Frame filter rate:1,480,000 for 1000Mbps

:148,000for100 Mbps :14,800for10Mbps

Frame forward rate: 1,480,000 for 1000Mbps

:148,000for100 Mbps :14,800for10Mbps

Network latency (using 64-byte packets):100Mbpsto 100 Mbps: 10ps max

Address database size: 8000 MAC addresses 256KB

262491.8 hrs (29.9 yrs)