Netgear MA401 Installation Guide
1. If you have chosen to install the card with the PC turned off,turn the power on now. The new hardware is found, and the driver is automatically loaded. Click "Next."
2. In the next Add New Hardware Wizard window, select "Search for the best driver for your device
(Recommended)," and then click "Next."
3. Click on "Specify a location" and enter the drive letter for the CD-ROM drive. Insert the
MA401/MA301 Wireless Network Card Resource CD. Click on "Browse"
4. Double-click on the CD-ROM drive letter. Double-click to select the
MA401
folder in the CD-ROM.
Click on the
WIN98
folder in the
MA401
folder, and click on "OK" to continue.
5. When Windows returns back to the original Add New Hardware Wizard window, the Specify a location entry field should show "D:\MA401\WIN98". assuming D: is the drive letter for the CD-ROM
drive. Click on "Next".
¤
Introduction
The MA401 802.11b Wireless PC Card helps you create a wireless network for sharing your broadband
cable or DLS internet access among multiple PCs in and around your home or office. It is designed for
notebook computers running Microsoft Windows 95B,98,2000,NT, Millennium.It is 16-bit PCMCIA
and 32-bit CardBus compatible and works in any available PCMCIA or CardBus slot. Its auto-s ensing
capability allows packet tranfer in 11Mbps for maximum throughput, or speed reduction to the lower
1Mbps speed for distance or working in a noisy environmen
As a last step, be sure to register your network card at http://www.netgear.com.
Make sure you have the following:
Install the Network Card
The MA401 802.11b Wireless PC Card is hot swappable,which means that you can insert it into a notebook that is either powered on or shut down. You must install the network card before installing the network driver.
Before you proceed with the installation steps, d ecide on a name for your network and for each PC (each
network must have the same workgroup name and each PC must have a unique computer name.)
Install the Network Driver
This section explains how to install the Windows 98 Network Driver. Other versions of Microsoft
Windows may respond with different dialog boxes,or the dialog boxes may open in a different sequence
than those shown in this guide, but should prompt you for the same information.
Note: You also need to have the Windows 98 CD and the MA401/MA301 Network Card Resource
CD ready to use in the installation process.
Note: If the "Insert Disk" dialog box opens and the "Please insert the disk labeled Windows 98..."
message appears at any time during the installation process, insert the Windows 98 CD and click
"OK." Then follow the next step in the instructions.
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054
USA
Phone: 1-888-NETGEAR
E-mail: support@NETGEAR.com
www.NETGEAR.com
Support Information
See Support Information Card for phone numbers.
Internet / World Wide Web
Go to http://www.NETGEAR.com for the NETGEAR Web page.
Defective or damaged merchandise can be returned to your point-of-sale representative.
IMPORTANT!
Please register online.YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE
RETAIN PROOF OF PURCHASE and this warranty information.To register your product, get product
support, or to obtain product information and NETGEAR product documentation,direct your Web
browser to the http://www.NETGEAR.com Web page. If you do not have access to the World Wide
Web, you can register your product using the enclosed registration card and mail it to NETGEAR
customer service.
February 2001
START HERE
1
OPEN BOX AND VERIFY CONTENTS
2
CONNECT NETGEAR TO YOUR ENVIRONMENT
1. Open the box
and verify its contents
2. Connect NETGEAR to
your environment
3. Install wireless LAN
configuration utility.
4. Configure wireless
parameters .
5. Enjoy being connected!
Model MA401
Wireless PC Card
MA401/MA301
Netword Card Resource CD.
Installation Guide and
Support Inforation Card
Model MA401
Wireless PC Card
M 1 - M A 4 0 1 N A - 0
802.11b W ireless PC Card
Installation Guide
MODEL
MA
401
¤
6. Windows indicates that the best driver for the device has been found. Click on "Next". Windows
starts copying files into your system.
7. In the next Add New Hardware Wizard window, click “Finish.”to complete the installation.
8. When asked if you want to reboot the system, remove the network card resource CD or the
Windows 98 CD from the CD-ROM drive,and then click "Yes" to reboot the system.
Verify Driver Installation
1. Dou ble-click "My Computer" on the Windows desktop,double-click "Control Panel" and then double
click "System".
2. Click on "Device Manager" folder tab, and double-click "Network adapters".
3. Dou ble-click "NETGEAR MA401 Wireless PC Card". A new window pops up with a
message box in the middle of the window describing the device status.
A wireless LAN configuration utility program is provided to give you information on your wireless network such as signal quality and link conditions,and to allow you to modify the various configurable
parameters of the PC card.
Install the wireless LAN configuration utility program
1. Insert the MA401/MA301 Network Card Resource CD into the CD-ROM drive. From the Windows
98 desktop, open
My Computer
. Double-click on the CD-ROM drive letter to look into the content
of the CD. Double-Click on the
MA401
folder and then double-click on the
UTILITY
folder
2. Double-click on the
SETUP
application icon to start the installation procedure. The Inst allShield
Wizard opens. Click on "Next" to continue.
3. Click "Yes" on the Software License Agreement window to accept the agreement.
4 Click on "Browse" to change the destination location where the wireless LAN configuration utility
program is installed. Otherwise, click on "Next" to continue.
5 Modify the "Program Folders" entry field if desired. Click on "Next" to continue.
6 Click on the "Yes, I want to restar t m y computer" button selection to rest ar t the computer. And
click on "Finish" to complete the installation.
System Tray Applications
Note:The SysTray (System Tray) resides on one end of the taskbar in the Microsoft Windows desktop.
It displays interface icons for memory-resident applications that execute in the background continuously,such as the clock, speaker volume, and virus detection.
The wireless LAN configuration utility installation for the MA401
Wireless PC Card adds a status reporting and configuration utility
icon in the SysTray. Once you have completed the installation, the
Windows 98 SysTray should show the following icon in different
colors. This icon indicates different status depending on the operating mode of the MA401 Wireless PC Card.
© 2001 by NETGEAR,Inc.All rights reserved.
Trademarks
NETGEAR
®
is a registered trademark of NETGEAR,INC.Windows®is a registered trademark of
Microsoft Corporation.Other brand and product names are trademarks or registered trademarks of
their respective holders.Information is subject to change without notice.All rights reserved.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability,NETGEAR reserves
the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s)
or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the Model MA401 Wireless PC Card has been suppressed in accordance with
the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992.The operation of some
equipment (for example, test transmitters) in accordance with the regulations may, however, be subject
to certain restrictions.Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on
the market and has been granted the right to test the series for compliance with the regulations.
VCCI Statement
This equipment is in the Class B category (information equipment to be used in a residential area
or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for
Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing radio
interference in such residential areas.
When used near a radio or TV receiver,it may become the cause of radio interference.
Read instructions for correct handling.
Federal Communications Commission (FCC) Compliance Notice:Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to par t 15 of the FCC
Rules.These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates,uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.However,there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna,(2) Increase the separation between the
equipment and receiver,(3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected,(4) Consult the dealer or an experienced radio/TV technician
for help.
Federal Communcations Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
EN 55 022 Statement
This is to certify that the Model MA401 Wireless PC Card is shielded against the generation of radio
interference in accordance with the application of Council Directive 89/336/EEC,Article 4a. Conformity
is declared by the application of EN 55 022 Class B (CISPR 22).
Compliance is dependent upon the use of shielded data cables.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Model MA401 Wireless PC Card) does not exceed the Class B limits for radionoise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (Model MA401 Wireless PC Card) respecte les limites de bruits radioélectriques
visant les appareils numériques de classe B prescrites dans le Règlement sur le
brouillage radioélectrique du ministère des Communications du Canada.
Double-click on the wireless SysTray icon
activates the wireless LAN configuration
utility for the MA401 Wireless PC Card. You
can click on any folder tab in window to
modify any operating parameter. The configurable parameters of the MA401 Wireless
PC Card show below.
With the NETGEAR MA401 Wireless PC Card installed, your notebook is now ready to network with
any IEEE 802.11b compatible wireless node to share files and peripheral.
For additional detail on configuring the MA401 Wireless PC Card, please refer to the reference guide
located in the MA401/MA301 Network Card Resource CD.
5
ENJOY BEING CONNECTED!
Declaration of Conformity
NETGEAR Model MA401 Wireless PC card
FOR HOME OR OFFICE USE
Tested to comply
with FCC Standards
TECHNICAL SPECIFICATION
3
INSTALL WIRELESS LAN CONFIGURATION UTILITY
Infrastructure mode
The wireless adapter is not able to link to any
access point or the link between the wireless
adapter and the access point is lost.
The link condition between the wireless adapter and
the associated access point is weak.
The wireless adapter has established good communication with an access point and the signal quality is
strong.
Icon color
Red
Yellow
Green
Ad-hoc mode
The wireless adapter has not
initiated communication with
any other wireless node.
Not applicable
The wireless adapter has successfully communicated with
another wireless node.
General Specifications Model MA401 Wireless PC Card
Radio Data Rate 1, 2, 5.5, 11 Mbps (Auto rate capable)
Frequency 2.4 GHz to 2.5 GHz Direct Sequence Spread Spectrum (DSSS)
Range outdoor environment indoor environment
1 Mbps-1650 ft (503 m) 1 Mbps-500 ft (152 m)
2 Mbps-1320 ft (402 m) 2 Mbps-400 ft (122 m)
5.5 Mbps-1155 ft (352 m) 5.5 Mbps-270 ft (82 m)
11 Mbps-835 ft (255 m) 11 Mbps-175 ft (53 m)
Encryption 40-bit (64-bit) WEP encryption
128-bit WEP encryption
Maximum Computers/network Limited by the amount of packets generated by each node;
typically 30 to 70
Bus interface PCMCIA Type II PC Card
Drivers Microsoft Windows 95B, 98, NT,2000, Millennium
Dimensions L: 85 mm (3.3 in)
W: 54 mm (2.1 in)
H: 5 mm (0.2 in)
Weight 43.4 g (1.6oz)
Status LEDs Wireless Activity
Environmental Specifications Operating temperature: 0 to 550C
Operating humidity: 10 to 90%, noncondensing
Electromagnetic Compliance FCC Part 15 Class B
Warranty Limited 5-year warranty
4
CONFIGURE WIRELESS PARAMETERS
Loading...