It is hereby certified that the Model MA311 Wireless PCI Adapter has been suppressed in accordance with the conditions set
out in the BMPT- AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in
accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating
instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has
been granted the right to test the series for compliance with the regulations.
VCCI Statement
This equipment is in the Class B category (information equipment to be used in a residential area or an adjacent area thereto)
and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and
Electronic Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the
possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm
(8 inches) during normal operation.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Model MA311 Wireless PCI Adapter) does not exceed the Class B limits for radio-noise emissions
from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna, (2)
Increase the separation between the equipment and receiver, (3) Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected, (4) Consult the dealer or an experienced radio/TV
technician for help.
With NETGEAR's MA311 802.11b Wireless PCI Adapter, you can effortlessly network any
desktop PC and avoid the hassles of traditional Ethernet wiring. This adapter helps you create a
wireless network for sharing your broadband cable or DSL Internet access among multiple PCs in
and around your home or office. It is designed for desktop computers equipped with PCI slots
running Microsoft Windows, and is equipped with auto-sensing capability that allows packet transfer
at 11 Mbps for maximum throughput, or will automatically adjust at the lower speeds for distance or
for operating in a noisy environment.
Features and Benefits
Quickly networks your employees without the time or expense of Ethernet cabling.
Networks from any location in and around the home or office.
Gives you constant access to corporate resources, e-mail and the intranet.
Supports the vast majority of desktop PCs.
Direct Sequence Spread Spectrum (DSSS) technology provides robust, interference-resistant
and secure wireless connectivity.
Supports 1, 2, 5.5, and 11 Mbps data rates.
Connects seamlessly to wired Ethernet and PC network LANs to augment existing networks
quickly and easily.
Provides greater flexibility to locate or move networked PCs.
Enables wireless networking to eliminate the cost of cabling.
Plug and Play makes it easy to install.
Features low power consumption.
Reliable IEEE 802.11b standards-based wireless technology.
Delivers up to 11 Mbps speed rate. Wireless nodes negotiate to operate in the optimal data
transfer rate. In a noisy environment or when the distance between the wireless nodes is far,
the wireless nodes automatically adjusts to operate at the optimal speed.
Supports data encryption up to 128-bit shared key method. You can also select 64-bit or no
encryption for faster data transfer rate.
Supports multiple operating system platforms, including Microsoft Windows 98, Windows NT,
Windows Me, Windows 2000 and Windows XP.
Applications
NETGEAR's MA311 Wireless PCI Adapter offers a fast, reliable, cost-effective solution for wireless
client access to the network in applications like these:
1. Remote access to corporate network information
E-mail, file transfer and Intranet access.
2. Difficult-to-wire environments
Historical or old buildings, asbestos installations, and open areas where wiring is difficult to
deploy
3. Frequently changing environments
Retailers, manufacturers, and those who frequently rearrange the workplace or change
locations
1
4. Database access
Doctors, nurses, retailers needing mobile database access while in the hospital, retail store
or office campus
5. SOHO (Small Office and Home Office) users
SOHO users needing easy and quick installation of a small computer network
Package Contents
The product package should contain:
MA311 802.11b Wireless PCI Adapter with an integral antenna
MA311 Resource CD with Windows Drivers
Quick Installation Guide
Support Information Card
Warranty and Registration Card
Please call your reseller or customer support in your area if there are any wrong, missing, or
damaged parts. You can refer to the Support Information Card for the telephone number of
customer support in your area. You should keep the Support Information Card, along with the
original packing materials, and use the packing materials to repack the MA311 Wireless PCI
Adapter if you need to return it for repair.
To qualify for product updates, product support, and product warranty registrations, register online
on the NETGEAR Web page at: http://www.NETGEAR.com.
CHAPTER 2: Installing the Drivers and Utility for Windows
98, Me, 2000, and XP
Important: Please install the MA311 drivers and utility BEFORE installing the MA311
hardware. Make sure the MA311 Adapter is NOT plugged into the PCI slot while you are
performing the following procedures.
NT users: Please see “Chapter 5: Installing the Drivers and Utility for Windows NT”
1. Power ON your computer. Insert the MA311 PCI Adapter Resource CD into the
CD-ROM drive. Click Start, Run and type ‘d:\setup’ if ‘d’ is the designation of your
CD drive.
2. When the Welcome screen appears, click Next.
3
3. The Choose Destination Location screen displays the default Destination Folder. If
you want to change the default folder, you can click Browse and choose a different
destination folder. Click Next to go to the next screen.
4
4. The Select Program Folder screen appears. Accept or change the default folder
name and click Next to continue.
5
5. Click Finish to complete the utility installation.
The next chapter, Chapter 3: Hardware Installation, explains how to complete the
MA311 PCI Adapter installation.
6
CHAPTER 3: Hardware Installation
Installing the Wireless PCI Adapter
Important: Be sure to install the MA311 drivers and utility BEFORE installing the MA311
hardware
1. Turn the power OFF and unplug the power cord from your computer.
2. Remove the PC cover.
3. Choose an available PCI slot (PCI slots are the shorter slots) and remove the corresponding
back plate from the PC chassis.
4. Insert the MA311 PCI Adapter into the PCI slot and fasten the adapter card to the computer
chassis by reinstalling and tightening the screw removed in step 3.
5. Power ON your desktop PC.
The Found New Hardware Wizard dialog box appears. Windows will automatically detect the
MA311 PCI Adapter and look for the driver. (only applies to Windows 98, Me, 2000 and XP)
6. For Windows 2000, a Digital Signature Not Found message may appear. Click Yes to
proceed.
7. For Windows XP, a Windows Logo Testing Not Found dialog box may appear. Click Continue
Anyway to proceed.
8. Click Finish to complete the installation.
The Hardware Installation is complete. Your MA311 PCI Adapter is now ready for use.
The Wireless LINK LED on the MA311 indicates the wireless link condition of the station with
another wireless node or the associated access point.
LINK LED
Solid Green – Associated with the Access Point or 802.11 Ad-Hoc wireless workstation
Blinking Green – Not connecting to the Access Point or Ad-Hoc wireless workstation
Try re-installing the card in your PC if the LINK LED behaves differently.
7
CHAPTER 4: Verifying Driver Installation
After the utility and the hardware installation are finished, Windows automatically installs the
necessary drivers (Windows 98, Me, 2000 or XP).
Verifying Driver Installation under Windows 98
1. From the Windows 98 desktop, double-click My Computer.
2. Double-click Control Panel. Double-click the System icon.
3. Click on the Device Manager folder tab.
4. Double-click Network Adapter. There should be no yellow exclamation mark or red cross-sign
on the MA311 PCI Adapter selection.
5. Double-click MA311 PCI Adapter. The Device Status windows should indicate that the MA311
PCI Adapter is working properly.
The installation of the MA311 PCI Adapter driver in Windows 98 is complete. Proceed to Chapter 6:
Wireless LAN Configuration.
Verifying Driver Installation under Windows Me
1. From the Windows Me desktop, double-click My Computer.
2. Double-click Control Panel. Double-click the System icon.
3. Click on the Device Manager folder tab.
4. Double-click Network Adapter. There should be no yellow exclamation mark or red cross-sign
on the NETGEAR MA311 PCI Adapter selection.
5. Double-click MA311 PCI Adapter. The Device Status windows should indicate that the MA311
PCI Adapter is working properly.
The installation of the MA311 PCI Adapter driver in Windows Me is complete. Proceed to Chapter 6:
Wireless LAN Configuration.
Verifying Driver Installation under Windows 2000
1. From the Windows 2000 desktop, double-click My Computer.
2. Double-click Control Panel. Double-click the System icon.
3. Click on the Hardware folder tab. Click the Device Manager button.
4. Double-click Network Adapter. There should be no yellow exclamation mark or red crosssign on the MA311 PCI Adapter selection.
5. Double-click MA311 PCI Adapter. The Device Status windows should indicate that the
MA311 PCI Adapter is working properly.
The installation of the MA311 PCI Adapter driver in Windows 2000 is complete. Proceed to
Chapter 6: Wireless LAN Configuration.
Verifying Driver Installation under Windows XP
1. From the Windows XP desktop, double-click My Computer.
2. Double-click Control Panel. Double-click the System icon.
3. Click on the Hardware folder tab. Click the Device Manager button.
8
Loading...
+ 23 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.