Netgear M6100 Installation Manual [zh]
M6100 Web Management User Guide
Software User Manual
September 2014
202-11439-01
350 East Plumeria Drive
San Jose, CA 95134
USA
M6100 Web Management User Guide
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it to register your product at
https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR
recommends registering your product through the NETGEAR website. For product updates and web support, visit
http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx.
Contact your Internet service provider for technical support.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc.
and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice.
© NETGEAR, Inc. All rights reserved.
Revision History
Publication Part Number Publish Date Comments
202-11439-01 September 2014 First publication
2
Contents
Chapter 1 Getting Started
Chapter 2 Configuring System Information
Switch Management Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Web Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Understanding the User Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Interface Naming Convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
System CPU Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Switch Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
USB Device Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Loopback Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Network Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
SDM Template Preference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Green Ethernet Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Device View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
DHCP Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
DHCP L2 Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
UDP Relay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
DHCPv6 Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
DHCPv6 Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Basic Chassis Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Advanced Chassis Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
NSF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
PoE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
SNMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
SNMP V1/V2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
SNMP V3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
LLDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
3
M6100 Web Management User Guide
LLDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
LLDP-MED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
ISDP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Timer Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Timer Global Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Timer Schedule Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Chapter 3 Configuring Switching Information
VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Auto-VoIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Protocol-based . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
OUI-based . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
iSCSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
iSCSI Global Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
iSCSI Sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
iSCSI Targets Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
iSCSI Sessions Detailed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Spanning Tree Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Multicast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
MFDB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
IGMP Snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
MLD Snooping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
MVR Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Address Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Port Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Port Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Link Aggregation Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
LAG Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
LAG Membership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Multiswitch Link Aggregation Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Virtual Port Channel Global Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Virtual Port Channel Interface Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 204
Virtual Port Channel Interface Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Virtual Port Channel Keepalive Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Virtual Port Channel Peer Link Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208
4
M6100 Web Management User Guide
Chapter 4 Routing
Routing Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
IPv6 Basic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
IPv6 Advanced. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
VLAN Routing Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
VLAN Routing Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
RIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Basic RIP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Advanced RIP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256
OSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Basic OSPF Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Advanced OSPF Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
OSPFv3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .294
Basic OSPFv3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .294
Advanced OSPFv3 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Router Discovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
Virtual Router Redundancy Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Basic VRRP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .322
Advanced VRRP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Multicast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
Multicast Mroute Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
Multicast Global Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
Multicast Interface Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333
Multicast DVMRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
Multicast IGMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
Multicast PIM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
Multicast Static Routes Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
Multicast Admin Boundary Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
IPv6 Multicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
IPv6 Multicast Mroute Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
IPv6 Multicast PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .355
IPv6 Multicast MLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
IPv6 Multicast Static Routes Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 369
Chapter 5 Configuring Quality of Service
Class of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
5
M6100 Web Management User Guide
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
Differentiated Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
DiffServ Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Chapter 6 Managing Device Security
Management Security Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
Local User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
Enable Password Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Line Password Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
RADIUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .399
TACACS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
Authentication List Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
Login Sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
Configuring Management Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
HTTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
HTTPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .419
Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
Denial of Service Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
Access Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
Port Authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
Traffic Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
MAC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
Port Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Private Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442
Protected Ports Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
Private VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
Storm Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
DHCP Snooping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
IP Source Guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455
Dynamic ARP Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
Captive Portal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
Configuring Access Control Lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
ACL Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479
Chapter 7 Monitoring the System
Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496
Port Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496
6
M6100 Web Management User Guide
Port Detailed Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498
EAP Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504
Cable Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .506
Buffered Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506
Command Log Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
Console Log Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
Syslog Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
Trap Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510
Event Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
Persistent Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Mirroring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
Multiple Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .513
sFlow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
Chapter 8 Maintenance
Save Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
Save Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
Auto Install Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
Device Reboot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
Power Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .521
Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521
Password Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522
Upload File From Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522
File Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523
HTTP File Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524
USB File Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525
Download File To Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526
File Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526
HTTP File Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528
USB File Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530
File Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530
Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Dual Image Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
Ping IPv4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .532
Ping IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .534
Traceroute IPv4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .535
Traceroute IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .537
Full Memory Dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538
Chapter 9 Help
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
Online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .540
7
M6100 Web Management User Guide
Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
User Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
Appendix A Default Settings
Appendix B Configuration Examples
Virtual Local Area Networks (VLANs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
VLAN Example Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
Access Control Lists (ACLs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547
MAC ACL Example Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548
Standard IP ACL Example Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549
Differentiated Services (DiffServ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
DiffServ Traffic Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
Creating Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
DiffServ Example Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552
802.1X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554
802.1X Example Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555
MSTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556
MSTP Example Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
Appendix C Notification of Compliance
8
1. Getting Started
This chapter provides an overview of starting your NETGEAR M6100 Chassis switch and
accessing the user interface. This chapter contains the following sections:
• Switch Management Interface on page 9
• Web Access on page 9
• Understanding the User Interfaces on page 10
• Interface Naming Convention on page 15
Switch Management Interface
The NETGEAR M6100 Chassis switch contains an embedded Web server and management
software for managing and monitoring switch functions. M6100 Chassis switch functions as a
simple switch without the management software. However, you can use the management
software to configure more advanced features that can improve switch efficiency and overall
network performance.
1
Web-based management lets you monitor, configure, and control your switch remotely using
a standard Web browser instead of using expensive and complicated SNMP software
products. From your Web browser, you can monitor the performance of your switch and
optimize its configuration for your network. You can configure all switch features, such as
VLANs, QoS, and ACLs by using the Web-based management interface.
Web Access
To access the M6100 Chassis switch management interface:
• Open a Web browser and enter the IP address of the switch in the address field.
You must be able to ping the IP address of the M6100 Chassis switch management interface
from your administrative system for Web access to be available. If you did not change the IP
address of the switch from the default value, enter 169.254.100.100 into the address field.
Accessing the switch directly from your Web browser displays the login screen shown in
Figure 1 on page 10.
9
M6100 Web Management User Guide
Figure 1. M6100 Web Interface
Understanding the User Interfaces
M6100 Chassis switch software includes a set of comprehensive management functions for
configuring and monitoring the system by using one of the following methods:
• Web user interface
• Simple Network Management Protocol (SNMP)
• Command Line Interface (CLI)
Each of the standards-based management methods allows you to configure and monitor the
components of the M6100 Chassis switch software.
system depends on your network size and requirements, and on your preference.
The W
Web-based interface to manage and monitor the system.
eb Management User Guide Software User Manual describes how to use the
The method you use to manage the
Using the Web Interface
To access the switch by using a Web browser, the browser must meet the following software
requirements:
• HTML version 4.0, or later
• HTTP version 1.1, or later
• Java Runtime Environment 1.6 or later
Supported web browsers include:
• Internet Explorer 10.0, 1
• Mozilla Firefox 26
• Chrome 32
1.0
Getting Started
10
M6100 Web Management User Guide
Use the following procedures to log on to the Web interface:
1. Open a W
eb browser and enter the IP address of the switch in the Web browser
address field.
2. The default username is admin, default password is none (no password).
username into the field on the login screen and then click Login. Usernames and
passwords are case sensitive.
Note: See User Management on page 396 for information about admin and
guest user accounts.
3. After the system authenticates you, the System Information page displays.
Figure 2 below shows the layout of the Managed Switch Web interface.
Navigation Tab
Feature Link
Help Link
Type the
Logout
Button
Help Page
Page Menu
Configuration Status and Options
Figure 2. Layout of the Web Interface
Navigation Tabs, Feature Links, and Page Menu
The navigation tabs along the top of the Web interface give you quick access to the various
switch functions. The tabs are always available and remain constant, regardless of which
feature you configure.
When you select a tab, the features for that tab appear as links directly under the tabs. The
feature links in the blue bar change according to the navigation tab that is selected.
The configuration pages for each feature are available as links in the page menu on the left
side of the page. Some items in the menu expand to reveal multiple configuration pages, as
Figure 3, Submenu Links on page 12 shows. When you click a menu item that includes
Getting Started
11
M6100 Web Management User Guide
multiple configuration pages, the item becomes preceded by a down arrow symbol and
expands to display the additional pages.
Page Link
Configuration
Pages
Figure 3. Submenu Links
Configuration and Monitoring Options
The area directly under the feature links and to the right of the page menu displays the
configuration information or status for the page you select. On pages that contain
configuration options, you can input information into fields or select options from menus.
Each page contains access to the HTML-based help that explains the fields and configuration
options for the page. Each page, except the Index page, also contains command buttons.
Table 1 shows the command buttons that are used throughout the pages in the Web
interface:
Table 1. Command Buttons
Button Function
Add Clicking Add adds the new item configured in the heading row of a table.
Apply Clicking the Apply button sends the updated configuration to the switch. Configuration
changes take ef
Cancel Clicking Cancel cancels the configuration on the screen and resets the data on the screen
to the latest value of the switch.
Delete Clicking Delete removes the selected item.
fect immediately.
Getting Started
12
M6100 Web Management User Guide
Table 1. Command Buttons
Button Function
Update Clicking the Update button updates the page with the latest information from the device.
Logout Clicking the
Logout button ends the session.
Device View
The Device View is a Java® applet that displays the ports on the switch. This graphic provides
an alternate way to navigate to configuration and monitoring options. The graphic also
provides information about device ports, current configuration and status, table information,
and feature components.
The Device View is available by selecting System
The port coloring indicates whether a port is currently active.
• Green indicates that the port is enabled.
• Red indicates that an error has occurred on the port, or that the link is disabled.
• Black indicates that no link is present.
The Device View of the switch is shown in Figure 4 below.
Device View.
Figure 4. M6100 Device View
Click the port you want to view or configure to see a port menu that displays statistics and
configuration options. Click the port menu option to access the page that contains the
configuration or monitoring options.
If you click the graphic, but do not click a specific port, the main menu appears, as shown in
Figure 5. This menu contains the same option as the navigation tabs at the top of the page.
Getting Started
13
M6100 Web Management User Guide
Figure 5. Device View Main Menu
Help Page Access
Every page contains a link to the online help , which contains information to assist in
configuring and managing the switch. The online help pages are context sensitive. For
example, if the IP
Help.
Addressing page is open, the help topic for that page displays if you click
User-Defined Fields
User-defined fields can contain 1 to 159 characters, unless otherwise noted on the
configuration Web page. All characters may be used except for the following (unless
specifically noted in for that feature):
Table 2:
\ <
/ >
* |
?
Using SNMP
The M6100 Chassis switch software supports the configuration of SNMP groups and users
that can manage traps that the SNMP agent generates.
M6100 Chassis switch uses both standard public MIBs for standard functionality and private
MIBs that support additional switch functionality. All private MIBs begin with a “-” prefix. The
main object for interface configuration is in -SWITCHING-MIB, which is a private MIB. Some
interface configurations also involve objects in the public MIB, IF-MIB.
SNMP is enabled by default. The System
Management System Information Web page,
which is the page that displays after a successful login, displays the information you need to
configure an SNMP manager to access the switch.
Getting Started
14
M6100 Web Management User Guide
Any user can connect to the switch using the SNMPv3 protocol, but for authentication and
encryption, the switch supports only one user which is admin; therefore there is only one
profile that can be created or modified.
To configure authentication and encryption settings for the SNMPv3 admin profile by using
eb interface:
the W
1. Navigate to the System SNMP SNMPv3 User Configuration page.
2. T
o enable authentication, select an Authentication Protocol option, which is either MD5 or
SHA.
3. T
o enable encryption, select the DES option in the Encryption Protocol field. Then, enter
an encryption code of eight or more alphanumeric characters in the Encryption Key field.
4. Click Apply .
To access configuration information for SNMP V1 or SNMP V2, click System
SNMP
SNMPv1/v2 and click the page that contains the information to configure.
Interface Naming Convention
The M6100 Chassis switch supports physical and logical interfaces. Interfaces are identified
by their type and the interface number. The physical ports are gigabit interfaces and are
numbered on the front panel. You configure the logical interfaces by using the software.
Table 3 describes the naming convention for all interfaces available on the switch.
Table 3. Naming Conventions for Interfaces
Interface Description Example
Physical The physical ports are gigabit
Ethernet interfaces and are
numbered sequentially starting
from one.
Link Aggregation Group (LAG) LAG interfaces are logical
interfaces that are only used for
bridging functions.
0/1, 0/2, 0/3, and so on
lag 1, lag 2, lag 3, and so on
CPU Management Interface This is the internal switch interface
responsible for the switch base
MAC address.
configurable and is always listed in
the MAC Address Table.
Routing VLAN Interfaces This is an interface used for routing
functionality
This interface is not
.
Getting Started
15
5/1
VLAN 1, VLAN 2, VLAN 3, and
so on
2. Configuring System Information
Use the features in the System tab to define the switch’s relationship to its environment. The
System tab contains links to the following features:
• Management on page 16
• Device View (See Device View on page 12)
• Services on page 55
• Chassis on page 79
• PoE on page 94
• SNMP on page 99
• LLDP on page 105
• ISDP on page 121
• Timer Schedule on page 126
2
Management
This section describes how to display the switch status and specify some basic switch
information, such as the management interface IP address, system clock settings, and DNS
information. From the Management link, you can access the following pages:
• System Information on page 17
• Switch Statistics on page 24
• System CPU Status on page 22
• USB Device Information on page 27
• Loopback Interface on page 29
• Network Interface on page 30
• Time on page 37
• DNS on page 43
• SDM Template Preference on page 45
• Green Ethernet Configuration on page 47
16
M6100 Web Management User Guide
System Information
After a successful login, the System Information page displays. Use this page to configure
and view general device information.
To display the System Information page, click System Management System Information.
A screen similar to the following displays.
Figure 6. System Information
The System Information provides various statuses.
Switch Status
To define system information:
1. Open the System Information page.
2. Define the following fields:
Configuring System Information
17
M6100 Web Management User Guide
a. System Name - Enter the name you want to use to identify this switch. You may use
up to 255 alphanumeric characters. The factory default is blank.
b. System Location - Enter the location of this switch.
You may use up to 255
alphanumeric characters. The factory default is blank.
c. System Contact - Enter the contact person for this switch.
You may use up to 255
alphanumeric characters. The factory default is blank.
d. Login Timeout - Specify how many minutes of inactivity should occur on a serial port
connection before the switch closes the connection. Enter a number between 0 and
160: the factory default is 5. Entering 0 disables the timeout.
3. Click Apply to send the updated screen to the switch and cause the changes to take ef
on the switch. These changes will not be retained across a power cycle unless a save is
performed.
The following table describes the status information the System Page displays.
Table 4. System Information
fect
Field Description
Product Name The product name of this switch.
IPv4 Network Interface The IPv4 address and mask assigned to the network
interface.
IPv6 Network Interface The IPv6 prefix and prefix length assigned to the
network interface.
IPv4 Loopback Interface The IPv4 address and mask assigned to the
loopback interface.
IPv6 Loopback Interface The IPv6 prefix and prefix length assigned to the
loopback interface.
System Date The current date.
System Up time The time in days, hours and minutes since the last
switch reboot.
Current SNTP Sync Status Displays the current SNTP sync status.
System SNMP OID The base object ID for the switch's enterprise MIB.
System Mac Address Universally assigned network address.
Supported Java Plugin Version The supported version of Java plugin.
Current SNTP Synchronized Time Displays the SNTP Synchronized time.
The highest temp in chassis (C) The general temperature of the switch in degrees
Centigrade.
Temperature traps range Identifies minimum and maximum of traps range.
Configuring System Information
18
M6100 Web Management User Guide
Backplane Information
This screens displays the backplane information. The following table describes the
information displayed.
Table 5. Backplane Information
Field Description
Model Identifier The model identifier
FPGA Version The FPGA version
Serial Number The serial number
Temperature Status
This screen shows the current temperature of the temperature sensors. The temperature is
instant and can be updated with the latest information on the switch when the Update button
is pressed. The maximum temperature of the temperature sensors depends on the actual
hardware.
Figure 7. Temperature Status
The following table describes the non-configurable Temperature Status information.
Table 6. Temperature Status Information
Field Description
Unit The unit number in the chassis.
Sensor The temperature sensor for the given unit.
Description The description of the temperature sensor.
Temp (C) The temperature of the specified unit in degrees
Centigrade.
State The unit temperature state.
Max Temp The maximum temperature of CPU and MACs.
Click Update to update the page with the latest information on the switch.
Configuring System Information
19
M6100 Web Management User Guide
FAN Status
This screen shows the status of the fans in all units. These fans remove the heat generated
by the power, CPU and other chipsets, and allow the chipsets work normally. Fan status has
three possible values: OK, Failure, and Not Present.
Figure 8. Fan Status
The following table describes the non-configurable Fan Status information.
Table 7. Fan Status
Field Description
Slot The slot number in the chassis.
Fan The fan index used to identify the fan for the given
chassis member
Description The description of the fan.
Type Specifies whether the fan module is fixed or
removable.
Speed The fan speed.
Duty Level The duty level of the fan.
State Specifies whether the fan is running or stopped.
.
Click Update to update the page with the latest information on the switch.
Device Status
This screen shows the software version of each device.
Configuring System Information
20
M6100 Web Management User Guide
Figure 9. Device Status
The following table describes the non-configurable Device Status information.
Table 8. Device Status
Field Description
Unit ID The unit number in the chassis.
Firmware Version The release.version.maintenance number of the
code currently running on the switch. For example, if
the release was 1, the version was 2 and the
maintenance number was 4, the format would be
'1.2.4'.
Boot Version The version of the boot code which is in the flash
memory to load the firmware into the memory
CPLD Version The version of the software for CPLD.
Serial Number The serial number of this switch.
.
Configuring System Information
21
M6100 Web Management User Guide
Field Description
Internal AC-1, Internal AC-2, etc. Indicates the status of the appropriate power module
in each unit. Status can be any of the following:
• Operational — Power module is present and
functioning properly.
• Powering — Main power is failed or disconnected
but RPS provides power to the switch.
• Not Present — Power module is not present in
the slot.
• Not powered — Power module is present but not
connected to the power source.
• Not powering — Power module is present and
connected but the switch uses another power
source.
• Incompatible — Power module is present but
incompatible.
• Failed — Power module is present, but power
cable is not plugged-in or a bad cable is
plugged-in.
PoE Version Version of the PoE controller FW image.
N/A indicates that the Poe is not supported by the
unit.
MAX PoE Indicates the status of maximum PoE power
available on the switch as follows:
• ON — Indicates less than 10W of PoE power
available for another device.
• OFF — Indicates at least 10W of PoE power
available for another device.
• N/A — Indicates that PoE is not supported by the
unit.
PoE D-Card Type Indicates the type of the PoE daughter card plugged
in. Possible values are:
• XCM89P — PoE card supporting 802.3at
standard (backward compatible with 802.3af).
• XCM89UP — PoE card supporting UPOE
pre-standard (backward compatible with
802.3af/802.3at).
• Not Installed — PoE card is not plugged in.
Click Update to update the page with the latest information on the switch.
System CPU Status
Use this page to display the system resources.
To display the System Resource page, click System > Management > System CPU Status.
A screen similar to the following is displayed.
Configuring System Information
22
M6100 Web Management User Guide
System CPU Status
The following table describes CPU Memory Status information.
Table 9. CPU Memory Status Information
Field Description
Total System Memory The total memory of the switch in KBytes.
Available Memory The available memory space for the switch in
KBytes.
CPU Utilization Information
This page displays the CPU Utilization information, which contains the memory information,
task-related information, and percentage of CPU utilization per task.
1. Select the Unit No. to display the CPU Utilization information.
2. Select All
to display the CPU Utilization information for all units in a chassis.
Configuring System Information
23
M6100 Web Management User Guide
CPU Threshold
The CPU Utilization Threshold notification feature allows you to configure thresholds that,
when crossed, trigger a notification. The notification is done via SNMP trap and SYSLOG
messages.
To display the CPU Threshold page, click System > Management > System CPU Status >
CPU Threshold.
A screen similar to the following is displayed.
Use CPU Threshold page to configure thresholds
1. Configure the Rising Threshold value. Notification is generated when the total CPU
utilization exceeds this threshold value over the configured time period.
to 100.
2. Configure the Rising Interval value.
configured from 5 to 86400 seconds in multiples of 5 seconds.
3. Configure the Falling Threshold. Notification is triggered when the total CPU utilization falls
below this level for a configured period of time.
to or less than the rising threshold value. The falling utilization threshold notification is made
only if a rising threshold notification was done previously. Configuring the falling utilization
threshold and time period is optional. If the Falling CPU utilization parameters are not
configured, then it takes the same value as Rising CPU utilization parameters. The range is
1 to 100.
4. Configure the Falling Interval. The
5 seconds to 86400 seconds in multiples of 5 seconds.
5. Configure the CPU Free Memory Threshold value in KB.
6. Click Apply to send the updated configuration to the switch. Configuration changes take
ef
fect immediately.
7. Click Cancel to cancel the configuration on the screen and reset the data on the screen to
the latest value of the switch.
This utilization monitoring time period can be
The falling utilization threshold must be equal
utilization monitoring time period can be configured from
The range is 1
Switch Statistics
Use this page to display the switch statistics.
To display the Switch Statistics page, click System > Management > Switch Statistics. A
screen similar to the following is displayed.
Configuring System Information
24
M6100 Web Management User Guide
The following table describes Switch Statistics information.
Table 10. Switch Statistics Information
Field Description
ifIndex This object indicates the ifIndex of the interface table
entry associated with the Processor of this switch.
Octets Received The total number of octets of data received by the
processor (excluding framing bits but including FCS
octets).
Packets Received Without Errors The total number of packets (including broadcast
packets and multicast packets) received by the
processor
Configuring System Information
25
.
M6100 Web Management User Guide
Field Description
Unicast Packets Received The number of subnetwork-unicast packets delivered
to a higher-layer protocol.
Multicast Packets Received The total number of packets received that were
directed to a multicast address. Note that this
number does not include packets directed to the
broadcast address.
Broadcast Packets Received The total number of packets received that were
directed to the broadcast address. Note that this
does not include multicast packets.
Receive Packets Discarded The number of inbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being deliverable to a
higher-layer protocol. A possible reason for
discarding a packet could be to free up buffer space.
Octets Transmitted The total number of octets transmitted out of the
interface, including framing characters.
Packets Transmitted Without Errors The total number of packets transmitted out of the
interface.
Unicast Packets Transmitted The total number of packets that higher-level
protocols requested that will be transmitted to a
subnetwork-unicast address, including those that
were discarded or not sent.
Multicast Packets Transmitted The total number of packets that higher-level
protocols requested that will be transmitted to a
Multicast address, including those that were
discarded or not sent.
Broadcast Packets Transmitted The total number of packets that higher-level
protocols requested that will be transmitted to the
Broadcast address, including those that were
discarded or not sent.
Transmit Packets Discarded The number of outbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being deliverable to a
higher-layer protocol. A possible reason for
discarding a packet could be to free up buffer space.
Most Address Entries Ever Used The highest number of Forwarding Database
Address Table entries that have been learned by this
switch since the most recent reboot.
Address Entries in Use The number of Learned and static entries in the
Forwarding Database Address Table for this switch.
Maximum VLAN Entries The maximum number of Virtual LANs (VLANs)
allowed on this switch.
Configuring System Information
26
M6100 Web Management User Guide
Field Description
Most VLAN Entries Ever Used The largest number of VLANs that have been active
on this switch since the last reboot.
Static VLAN Entries The number of presently active VLAN entries on this
switch that have been created statically
Dynamic VLAN Entries The number of presently active VLAN entries on this
switch that have been created by GVRP registration.
VLAN Deletes The number of VLANs on this switch that have been
created and then deleted since the last reboot.
.
Time Since Counters Last Cleared
The elapsed time, in days, hours, minutes, and
seconds, since the statistics for this switch were last
cleared.
Click Clear to clear all the counters, resetting all switch summary and detailed statistics to
default values. The discarded packets count cannot be cleared.
USB Device Information
This page displays the USB device status.
To display the USB device information page, click System > Management > USB Device
Information.
A screen similar to the following is displayed.
USB Device Details
This screen displays the non-configurable USB device details shown in the following table.
Configuring System Information
27
M6100 Web Management User Guide
Table 11. USB Device Details
Field Description
Device Status This field specifies the current status of the device.
Status is:
• Active if the device is USB plugged in and
recognized by the switch.
• Inactive if the device is not mounted.
• Invalid if the device is not present or an invalid
device is plugged in.
Click Update to update the page with the latest information on the switch.
USB Memory Statistics
This screen displays the memory statistics of the USB flash device.
The following table describes the non-configurable USB Memory Statistics information.
Table 12. USB Memory Statistics Information
Field Description
Total Size This field displays the USB flash device storage size
in bytes.
Bytes Used This field displays the size of memory used on the
USB flash device.
Bytes Free This field displays the size of memory free on the
USB flash device.
Click Update to update the page with the latest information on the switch.
USB Directory Details
This screen displays the directory information of the USB flash device.
The following table describes the non-configurable USB Directory Details information.
Table 13. USB Directory Details Information
Field Description
File Name This field displays the Name of the file stored in the
USB flash drive.
Configuring System Information
28
M6100 Web Management User Guide
Field Description
File Size This field displays the Size of the file stored in the
USB flash drive in bytes
Modification Time
This field displays the Last modification time of the
file stored in the USB flash drive.
Click Update to update the page with the latest information on the switch.
Loopback Interface
Use this page to create, configure, and remove Loopback interfaces.
To display the Loopback Interface page, click System > Management > Loopback Interface.
A screen similar to the following is displayed.
1. Use the Loopback Interface Type field to select IPv4 or IPv6 loopback interface to
configure the corresponding attributes.
2. Use the Loopback ID field to select list of currently configured loopback interfaces.
3. Use the Primary Address field to input the primary IPv4 address for this interface in dotted
decimal notation.
This option is visible when IPv4 loopback is selected.
4. Use the Primary Mask field to input the primary IPv4 subnet mask for this interface in dotted
decimal notation.
5. Use the Secondary IP
This option is visible when IPv4 loopback is selected.
Address field to input the secondary IP address for this interface in
dotted decimal notation. This input field is visible only when 'Add Secondary' is selected.
This option is visible when IPv4 loopback is selected.
6. Use the Secondary Subnet Mask field to input the secondary subnet mask for this interface
in dotted decimal notation.
This input field is visible only when 'Add Secondary' is selected.
This option is visible when IPv4 loopback is selected.
7. Use the IPv6 Mode field to enable IPv6 on this interface using the IPv6 address.
This option
is only configurable prior to specifying an explicit IPv6 address. This option is visible when
IPv6 loopback is selected.
Configuring System Information
29
M6100 Web Management User Guide
8. Use the IPv6 Address field to enter the IPv6 address in the format prefix/length. This option
is visible when IPv6 loopback is selected.
9. Use the EUI64 field to optionally specify the 64-bit extended unique identifier (EUI-64).
option is visible when IPv6 loopback is selected.
This
Network Interface
From the System > Management > Network Interface link, you can access the following
pages:
• IPv4 Network Configuration on page 30
• IPv6 Network Interface Configuration on page 32
• IPv6 Network Interface Neighbor Table on page 33
• IPv4 Service Port Configuration on page 34
• IPv6 Service Port Configuration on page 35
IPv4 Network Configuration
To display the IPv4 Network Configuration page, click System > Management > Network
Interface > IPv4 Network Configuration. A screen similar to the following is displayed.
The network interface is the logical interface used for in-band connectivity with the switch via
any of the switch's front panel ports. The configuration parameters associated with the
switch's network interface do not affect the configuration of the front panel ports through
which traffic is switched or routed
Configuring System Information
30
Loading...