Page 1
GS700TPS Hardware
Installation Guide
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, California 95134
202-10488-01
April 2009
Page 2
© 2009 by NETGEAR, Inc. All rights reserved.
Technical Support
Please refer to the support information card that shipped with your product. By registering your product at
http://www.netgear.com/register, we can provide you with faster expert technical support and timely notices of product
and software upgrades.
NETGEAR, INC. Support Information
Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support information card on your
Resrouce CD.
E-mail: support@netgear.com
North American NETGEAR web site: http://www.netgear.com
Trademarks
NETGEAR, the NETGEAR logo, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc.
Microsoft, Windows, and Wi ndows NT are registered trademarks of Microsoft Corporation. Other brand and product
names are registered trademarks or trademarks of their respective holders. Portions of this document are copyright
Intoto, Inc.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the GS700TPS Smart Switch has been suppressed in accordance with the conditions set out in
the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in
accordance with the regulations may, however , be subject to certain restricti ons. Please refer to the notes in the operating
instructions.
The Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and
has been granted the right to test the series for compliance with the regulations.
Bestätigung des Herstellers/Importeurs
Es wird hiermit bestätigt, daß das Switch gemäß der im BMPT-AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten
Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B. Testsender) kann jedoch gewissen
Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt
gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the Class B category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas. When used
near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.
ii
v1.0, April 2009
Page 3
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National laws for usage of radio
spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result
in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.
NOTE: This product's firmware limits operation to only the channels allowed in a particular Region or Country.
Therefore, all options described in this user's guide may not be available in your version of the product.
Europe – EU Declaration of Conformity
Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the
following EU Council Directives: 89/336/EEC and LVD 73/23/EEC. Compliance is verified by testing to the following
standards: EN55022 Class A, EN55024 and EN60950-1.
EN300 328, EN301 489-17, EN60950
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antenn as only. Any
product changes or modifications will invalidate all applicable regulatory certifications and approvals
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or oper
ating in conjunction with any other antenna or transmitter.
FCC Declaration Of Conformity
We NETGEAR, Inc., 4500 Great America Parkway, Santa Clara, CA 95054, declare under our sole responsibility that
the model GS700TPS Gigabit Stackable Smart Switch with PoE complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions:
• This device may not cause harmful interferen
• This device must accept any interference received, including interference that may cause undesired operation.
ce, and
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following methods:
• Reorient or relocate the receiving antenna
iii
v1.0, April 2009
Page 4
• Increase the separation between the equipment and the receiver
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
GS700TPS Gigabit Stackable Smart
• Connect the equipment into an electrical
• Consult the dealer or an experienced radio/TV technician for help.
Modifications made to the product, unless expressly approved by NETGEAR, Inc., could void the user's right to operate
the equipment.
outlet on a circuit different from that which the radio receiver is connected
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (GS700TPS Gigabit Stackable Smart Switch with PoE) does not exceed the Class B limits for
radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Product and Publication Details
Model Number: GS700TPS
Publication Date: April 2009
Product Family: Smart Switch
Product Name: GS700TPS Smart Switch
Home or Business Product: Business
Language: English
Publication Part Number: 202-10488-01
Publication Version Number: 1.0
iv
v1.0, April 2009
Page 5
Contents
About This Guide
Conventions, Formats and Scope ....................................................................................vii
How to Use This Manual .................................................................................................viii
How to Print this Manual ..................................................................................................viii
Revision History ..................... ... ... .... ... ... ... .......................................... .............................. ix
Chapter 1
Introduction
Overview ................................... ................ ................ ................. ................ ................ .....1-1
Switch Features ............................... ... .......................................... ..................................1-3
Package Contents ..........................................................................................................1-7
Chapter 2
Installation
Step 1: Preparing the Site ...............................................................................................2-1
Step 2: Installing the Switch ............................................................................................2-2
Step 3: Checking the Installation ..................................... ... ... .... ... ... ... .... ... ... ... ... .... ... ..... 2-3
Step 4: Connecting Devices to the Switch ....................... ... ... .... ... ... ... .... ... ... ... ... .... ... ... ..2-4
Step 5: Installing an SFP GBIC Module ..........................................................................2-5
Step 6 Installing Device as Stand-alone or Stack Master ...............................................2-5
Step 7: Applying AC Power ............................................................................................2-7
Step 8: Managing the Switch via a Web Browser/PC Utility for Initial Configuration ......2-7
Chapter 3
Physical Description
Front and Back Panel Configuration ...............................................................................3-1
LED Designations ...........................................................................................................3-3
Device Hardware Interfaces ...........................................................................................3-5
Appendix A
Troubleshooting
Troubleshooting Chart ................................................................................................... A-1
Additional Troubleshooting Suggestions ................................................... ... ... ... .... ... ... . A-2
v1.0, April 2009
v
Page 6
Appendix B
Technical Specifications
Index
vi
v1.0, April 2009
Page 7
About This Guide
Congratulations on the purchase of the NETGEAR Smart Switch. The NETGEAR® Installation
Manual describes how to install, configure and troubleshoot the smart sw itch. The information in
this manual is intended for readers with intermediate computer and Internet skills.
Conventions, Formats and Scope
The conventions, formats, and scope of this manual are described in the following paragraphs:
• T
ypographical Conventions. This manual uses the following typographical conventions:
Italics Books, CDs, URL names
Bold User input
Fixed Screen text, file and server names, extensions, commands, IP addresses
• Formats. This manual uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Tip: This format is used to highlight a procedure that will save time or resources.
Warning: Ignoring this type of note may result in a malfunction or damage to the
equipment.
Danger: This is a safety warning. Failure to take heed of this notice may result in
personal injury or death.
v1.0, April 2009
vii
Page 8
GS700TPS Smart Switch
• Scope. This manual is written for the GS700TPS according to these specifications:
Product Version GS700TPS Smart Switch
Manual Publication Date April 2009
Note: Product updates are available on the NETGEAR, Inc. web site at
http://kbserver.netgear.com/main.asp.
How to Use This Manual
The HTML version of this manual includes the following:
• Buttons,
at a time.
•The
in the table of contents or index to navigate directly
manual.
•The
product model.
• Links to PDF versions of the full manual
and , for browsing forwards or backwards through the manual one page
button displays the table of contents and the button. Double-click on a link
to where the topic is described in the
button accesses the full NETGEAR, Inc. online knowledge base for a particular
and individual chapters.
How to Print this Manual
To print this manual you can select one of the following options, according to your requirements.
• Printing a Page in the HTML View - Each page in the HTML version of the manual is
dedicated to a major topic. Use the Print button on the browser toolbar to print the page
contents.
• Printing a Chapter - Use the PDF
– Click the PDF of
print. The PDF version of the chapter you were viewing opens in a bro wser window.
– Your computer must have the free Adobe Acrobat reader installed
print PDF files. The Acrobat reader is available on the Adobe Web site at
http://www.adobe.com.
This Chapter link at the top right of any page in the chapter you want to
of This Chapter link at the top left of any page.
in order to view and
viii
v1.0, April 2009
Page 9
GS700TPS Smart Switch
– Click the print icon in the upper left of the window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can
save paper and printer ink by selecting this feature.
• Printing the Full Manual - Use the Complete PDF Manual link at the top left of any page.
– Click the Complete PDF Manual link at the top
version of the complete manual opens in a browser window.
– Click the print icon in the upper left of the window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can
save paper and printer ink by selecting this feature.
Revision History
Part Number
202-10488-01 1.0 April 2009 First release
Version
Number
Date Description
left of any page in the manual. The PDF
v1.0, April 2009
ix
Page 10
GS700TPS Smart Switch
x
v1.0, April 2009
Page 11
Chapter 1
Introduction
The NETGEAR Smart Switch is a state-of-the-art, high-performance, IEEE-compliant network
solution designed for users who require a large number of ports and want the power of Gigabit
connectivity to eliminate bottlenecks, boost performance, and increase productivity. To simplify
installation, the switch is shipped ready for use out of the box.
This chapter serves as an introduction to the GS700TPS Smart Switch and provides the following
information:
• “Overview”
• “Switch Features”
• “Package Contents”
Overview
This Installation Guide is for the following NETGEAR Smart Switches:
• GS724TPS - This product offers support for 24 ports of 10/100/1000M (Base-T) and four
Form-factor slots which support 10/100/1000 (1000Base-SX/LX/FX) SFP. This product
supports the added feature of Power over Ethernet (PoE).
• GS748TPS - This product offers support for 48 ports of 10/100/1000M (Base-T) and four
Form-factor slots which support 10/100/1000 (1000Base-SX/LX/FX) SFP. This product
supports the added feature of Power over Ethernet (PoE).
You can make high-speed connections using the Gigabit ports. For example:
• Connecting to a network backbone
• Linking to high-speed servers
• Providing 10/100/1000 copper and fiber connectivity
The GS700TPS Smart Switch also provides the benefit of administrative management with a
complete package of features for the observation, configuration, and control of the network . With
a Web-based Graphical User Interface (GUI), you can view the switch’s many features and use
them in a simple and intuitive manner. The switch’s management features include configuration
1-1
v1.0, April 2009
Page 12
GS700TPS Smart Switch
for port and switch information, VLAN for traffic control, port trunking for increased bandwidth,
and Class of Service (CoS) for traffic prioritization. These features provide better understanding
and control of the network. Initial discovery of the switch on the network requires the Smart
Wizard Discovery program, a utility that runs on a PC.
The GS700TPS Smart Switch can be free-standing, or rack mounted in a wiring closet or
equipment room. It is IEEE-compliant and offers low latency for high-speed networking. All ports
can automatically negotiate to the highest speed. This capability makes the switch ideal for
environments that have a mix of Ethernet, Fast Ethernet, or Gigabit Ethernet devices. In addition,
all RJ-45 ports operate in half- or full-duplex mode. The maximum segment length is 328 feet (100
meters) over Category 5 Unshielded Twisted-Pair (UTP) cable, but much longer for fiber
connections using SFP GBIC modules.
1-2 Introduction
v1.0, April 2009
Page 13
GS700TPS Smart Switch
The NETGEAR Smart Switch can be used as a desktop to build a small network that enables 1000
Mbps access to a file server. With full-duplex enabled, the switch port connected to the server or
PC can provide 2000 Mbps throughput.
Figure 1-1
Switch Features
The following list identifies the key features of the NETGEAR Smart Switch.
• On the GS700TPS Smart Switch device there are 4
Gigabit Ethernet switching ports, four of which are Combo ports.
Introduction 1-3
v1.0, April 2009
8 RJ-45 ports 10/100/1000M auto sensing
Page 14
GS700TPS Smart Switch
• Four Small Form-factor Pluggable (SFP) GBIC slots, which function as combo ports. Combo
ports are single ports with two physical connections, SFP fiber and RJ-45 copper. The RJ-45
copper ports corresponding to the Combo ports are the four 10/100/1000M auto-sensing Giga
switching ports on each device.
• Two dedicated high speed stacking ports, with minimum stacking bandwidth of 20 Gbps
(aggregate, bi-directional) via the device’s HX Stack ports.
• The following SFP types are supported:
• 1000Base-SX
• 1000Base-LX
• 100Base-FX
• The device supports full Netgear Smart Switch functionality.
• The device provides full compatibility with IEEE standards:
• IEEE 802.3i, (10Base-T)
• IEEE 802.3u (100Base-TX, 100Base-FX)
• IEEE 802.3x (Full-duplex flow control)
• IEEE 802.3ab (1000Base-T)
• IEEE 802.3z (1000Base-X)
• IEEE 802.3at (DTE Power via MDI) (Port 1 - 4)
• Auto-sensing and auto-negotiating capabilities for all ports.
• Auto Uplink™ on all ports to make the right connection.
• Automatic address-learning function to build the packet-forwarding information table. The
table contains up to 8K Media Access Control (MAC) addresses.
• Full- and half-duplex functions for all 10/100/1000 Mbps ports.
• Store-and-Forward transmission to remove bad packets from the network.
• Full-duplex IEEE 802.3x pause frame flow control.
• Active flow control to minimize packet loss/frame drops.
• Half-duplex back-pressure control.
• Per port LEDs, System LEDs.
• Internal power supply.
1-4 Introduction
v1.0, April 2009
Page 15
GS700TPS Smart Switch
• Standard 1U high, rack mountable 19”chassis.
• Fan speed control supported
The GS724TPS supports the following PoE functions:
• Smart Power Managed function handles the power of each port in the event of limited
available power.
• Supports the 24-Port PoE function as follows:
• 15.4W for 12 ports
• 8W for 24 ports
for a total of 192W for PoE. The GS724TPS, using data pairs (RJ-45 1, 2, 3 and 6 pin),
provides power to the PD.
GS748TPS supports the following PoE functions:
• The Smart Power Managed function handles the power of each port in the event of limited
available power.
• Supports the 48-Port PoE functions as follows:
• 15.4W for 24 ports
• 8W for 48 ports
for a total of 384W for PoE. The GS748TPS, using data pairs (RJ-45 1, 2, 3 and 6 pin),
provides power to the PD.
Stacking
A stack can be controlled and managed from a single unit called the master unit. Any other unit
member of the stack is named stack slave.
In particular, firmware can be downloaded from the stack master to the other units in the stack.
A unit serving as Stack Master runs the fully operational software of a switch. In addition, it runs
the master part of the Distributed Switching Application that configures and manages all other
units in the stack. Generally, the master operates the remote Slave’s low-level drivers, thorough
the Distributed Switching application part that is running in the context of the Slave.
During the Stacking setup, the switches will auto-select one as the Stacking Master. All other
devices are named as slave stack members, and assigned a unique Unit ID. One of the slave units is
designated as the backup master. The backup master acts as a slave stack master , but can become a
Introduction 1-5
v1.0, April 2009
Page 16
GS700TPS Smart Switch
stack master in the event of failure of stack master. The master and backup master are assigned
unit IDs of 1 and 2. The Stack Master provides a Single point of control and management as well
as a single interface in which to control and manage the stack.
Switch software is downloaded separately for each stack members. However, all units in the stack
must be running the same software version.
A stack unit can operate in one of the following Modes:
• Standalone unit runs as a general switch. The standalone unit does not run the stacking
application, until it is connected to a stack.
• The Master unit manages the entire stack, and is responsible for the entire stack configuration.
All protocols run in the context of the Master unit. It is responsible to update and synchronize
the Backup master.
• A master-backup unit runs as a slave unit as described above, and in addition, it continuously
monitors the existence and operation of the stack master. If the master unit fails, the masterbackup unit will assume the stack-master role. (“Switchover”).
• A slave unit only runs a slave version of the Distributed Switching Algorithm, which allows
the applications running on the Master unit’s CPU to control and manage the resources of the
slave unit.
1-6 Introduction
v1.0, April 2009
Page 17
GS700TPS Smart Switch
Package Contents
Figure 1-2 shows the NETGEAR Smart Switch package contents.
Figure 1-2
Verify that the package contains the following:
• NETGEAR Smart Switch
• Stacking Cable
• Rubber footpads for tabletop installation
• Power cord
• Rack-mount Kit for installing the switch in a 19-inch
rack
• Installation Guide
• Smart Switch Resource CD with Smart Wizard Discovery and User’s manual
• Warranty/Support Information Card
If any item is missing or damaged, contact the place of purchase immediately.
Introduction 1-7
v1.0, April 2009
Page 18
GS700TPS Smart Switch
1-8 Introduction
v1.0, April 2009
Page 19
Chapter 2
Installation
This chapter describes the installation procedures for your NETGEAR Smart Switch. Switch
installation involves the following steps:
“Step 1: Preparing the Site”
“Step 2: Installing the Switch”
“Step 3: Checking the Installation”
“Step 4: Connecting Devices to the Switch”
“Step 5: Installing an SFP GBIC Module”
“Step 6 Installing Device as Stand-alone or Stack Master”
“Step 7: Applying AC Power”
“Step 8: Managing the Switch via a Web Browser/PC Utility for Initial Configuration”
Step 1: Preparing the Site
Before installing the switch, ensure the operating environment meets the requirements in the
following table.
Table 2-1. Site Requirements
Characteristics Requirements
Mounting • Desktop installations - Provide a flat table or shelf surface.
• Rack-mount installations - Use a 19-inch (48.3-centimeter) EIA standard equipment
rack that is grounded and physically secure. The rack-mount kit supplied with the switch
is also required.
Access Locate the switch in a position that allows access to the front panel RJ-45 ports, the ability
to view the front panel LEDs, and easy safe access to the power connector.
v1.0, April 2009
2-1
Page 20
GS700TPS Smart Switch
Table 2-1. Site Requirements
Characteristics Requirements
Power source Provide a power source within 6 feet (1.8 meters) of the installation location. Power
specifications for the switch are shown in Appendix A, “Troubleshooting”. Ensure the AC
outlet is not controlled by a wall switch, which can accidentally turn off power to the outlet
and the switch.
Environmental • Temperature - Install the switch in a dry area, with ambient temperature between 0 and
50ºC (32 and 122ºF). Keep the switch away from heat sources such as direct sunlight,
warm air exhausts, hot-air vents, and heaters.
• Operating humidity - The installation location should have a maximum relative
humidity of 90%, non-condensing.
• Ventilation - Do not restrict airflow by covering or obstructing air inlets on the sides of
the switch. Keep at least 2 inches (5.08 centimeters) free on all sides for cooling. Be
sure there is adequate airflow in the room or wiring closet where the switch is installed.
• Operating conditions - Keep the switch at least 6 ft. (1.83 m) away from nearest
source of electromagnetic noise, such as a photocopy machine.
Step 2: Installing the Switch
The NETGEAR Smart Switch can be installed on a flat surface or in a standard 19-inch rack.
Installing the Switch on a Flat Surface
The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the
four concave spaces on the bottom of the switch. The rubber footpads cushion the switch against
shock/vibrations.
Installing the Switch in a Rack
To install the switch in a rack, use the following procedure (and refer to Figure 2-1). To perform
this procedure, you need the 19-inch rack-mount kit supplied with switch.
1. Attach the supplied mounting brackets to the side of the switch.
2. Insert the screws provided in the rack-mount kit through each bracket and into the bracket
mounting holes in the switch.
3. Tighten the screws with a #1 Phillips screwdriver to secure each bracket.
4. Align the mounting holes in the brackets with the holes in the rack, and insert two pan-head
screws with nylon washers through each bracket and into the rack.
2-2 Installation
v1.0, April 2009
Page 21
GS700TPS Smart Switch
5. Tighten the screws with a #2 Phillips screwdriver to secure the switch in the rack.
Figure 2-1
Note: Always install devices from the bottom of the to the top. This will prevent the rack
from over balancing and toppling over.
Step 3: Checking the Installation
Before applying power perform the following:
• Inspect the equipment thoroughly.
• Verify that all cables are installed correctly.
• Check cable routing to make sure cables are not
Installation 2-3
v1.0, April 2009
damaged or creating a safety hazard.
Page 22
GS700TPS Smart Switch
• Ensure all equipment is mounted properly and securely.
Step 4: Connecting Devices to the Switch
The following procedure describes how to connect PCs to the switch’s RJ-45 ports. The
NETGEAR Smart Switch contains Auto Uplink™ technology , which allows you to attach devices
using either straight-through or crossover cables.
Figure 2-2
Connect each PC to an RJ-45 network port on the Switch front panel (Figure 2-2). Use Category 5
(Cat5) Unshielded Twisted-Pair (UTP) cable terminated with
an RJ-45 connector for these
connections.
Note: Ethernet specifications limit the cable length between the switch and the attached
device to 100 m (328 ft.).
2-4 Installation
v1.0, April 2009
Page 23
GS700TPS Smart Switch
Step 5: Installing an SFP GBIC Module
The following procedure describes how to install an SFP Gigabit Ethernet module in the switch’s
Gigabit module bay. Standard SFP GBIC modules are sold separately from the Smart Switch. If
you do not plan to install an SFP GBIC module at this time, skip this procedure.
To install an SFP GBIC module:
1. Insert t
2. Press firmly to ensure the module
Figure 2-3
he SFP module into the SFP module bay.
seats into the connector.
Step 6 Installing Device as Stand-alone or Stack Master
A master-backup unit runs as a slave unit as described above, and in addition, it continuously
monitors the existence and operation of the stack master. If the master unit fails, the master-backup
unit will assume the stack-master role. (“Switchover”) – master backup could be with unit ID 1 or
2. The goal for switchover time is under 30 seconds.
If stacking cable failed or a stack unit extracted in a
from the stack (which puts them in an ambiguous state), and they will set all their ports to down
state.
Installation 2-5
v1.0, April 2009
chain topology, slave units could be disjointed
Page 24
GS700TPS Smart Switch
Each unit may work in one of two modes: Stand-alone, or Stack-mode. The operational mode is
determined at Boot time of the software, and can only be changed by a unit reset. The stacking 7
Segment LED is not illuminated (off) if the unit is operating in stand-alone mode.
At factory default, units boot in Stack mode. This is the default setting.
setting from the System > Management > System Information screen.
Setting the unit mode can be done
either by a specific command (Using WEB GUI).
If required, change this
There are two stacking topologies supported by the device, the Ring topology or Chain
topology.
Figure 2-4
The device is “Plug and Play” in terms of stacking configuration. Before powering up the
device, connect the devices into the required stacking topology. Power up the devices. The
stacking Master and slave designations are configured through automatic discovery.
Manually changing the stacking configuration is through switch’s web page once the
device has been booted and is operational.
For more information on stacking see the Software Administrator User Guide. A link to
the User Guide is on your Resource CD.
2-6 Installation
v1.0, April 2009
Page 25
GS700TPS Smart Switch
Step 7: Applying AC Power
NETGEAR Smart Switch does not have an ON/OFF switch. The method of applying or removing
AC power is by connecting or disconnecting the power cord. Before connecting the power cord,
select a grounded 3-pronged AC source that is not controlled by a wall switch, which can turn off
power to the switch. After selecting an appropriate AC source, use the following procedure to
apply AC power.
1. Connect the female end of the
back of the switch.
2. Co
When applying power, the Power LED on the switch’s front panel is green.
If the Power LED does light up, check that the power c
power source is functioning correctly. If this does not resolve the problem, refer to Appendix A -
“Troubleshooting”.
nnect the 3-pronged end of the AC power adapter cable to the 3-pronged AC source.
supplied AC power adapter cable to the power receptacle on the
able is plugged in correctly and that the
Step 8: Managing the Switch via a Web Browser/PC Utility for Initial Configuration
The NETGEAR Smart Switch contains software for viewing, changing, and monitoring the way it
works. This management software is not required for the switch to work. You can use the ports
without using the management software. However , the management software enables you to setup
VLAN and Trunking features, and also improves the efficiency of the switch, which results in the
improvement of its overall performance as well as the performance of the network.
After powering up the switch for the first time, you can configure the Smart Switch
browser or a utility program called Smart Wizard Discovery. For more information about
managing the switch, see the Software Manual on the Smart Switch Resource CD.
using a Web
Note: When the device powers up, there is a default IP address already configured on the
device. The default IP address is 192.168.0.239 and subnet mask 255.255.255.0.
Installation 2-7
v1.0, April 2009
Page 26
GS700TPS Smart Switch
2-8 Installation
v1.0, April 2009
Page 27
Chapter 3
Physical Description
This chapter describes the NETGEAR Smart Switch hardware features. The topics include:
• “Front and Back Panel Configuration”
• “LED Designations”
• “Device Hardware Interfaces”
Front and Back Panel Configuration
GS724TPS Front Panel
The GS724TPS is a 24-Ports 10/100/1000M + 4 SFP Combo ports Smart switch. E very RJ45 po rt
is capable of sensing the line speed and negotiating the operation duplex mode with the link
partner automatically.
Figure 3-1 illustrates the NETGEAR GS724TPS
Figure 3-1
The front panel contains the following:
• 24 RJ-45 connectors for 10/100/1000Mbps auto sensing Gigabit Ethernet switching ports.
• Four SFP slots for SFP modules supporting 1000(1000Base-SX/LX)/100M SFP.
• Reset button to restart the device.
• Recessed default reset button to restore the device back to the
device the button is depressed for more than 5 seconds.
• One LED Mode Push Button to switch PoE enable
PoE mode LED.
v1.0, April 2009
Smart Switch front panel
factory defaults. To restore the
d LEDs between Ethernet mode LED or
3-1
Page 28
GS700TPS Smart Switch
• Port LEDs.
• System LEDs.
GS748TPS Front Panel
The GS748TPS is a 48-Ports 10/100/1000M + 4 SFP Combo ports Smart switch. E very RJ45 po rt
is capable of sensing the line speed and negotiating the operation duplex mode with the link
partner automatically.
Figure 3-2 illustrates the NETGEAR GS748TPS
Figure 3-2
The front panel contains the following:
• 48 RJ-45 connectors for 10/100/1000Mbps auto sensing Gigabit Ethernet switching ports.
• Four SFP slots for SFP modules supporting 1000
• Reset button to restart the device.
• Recessed default reset button to restore the device back to the
device the button is depressed for more than 5 seconds.
• One LED Mode Push Button to switch PoE enable
PoE mode LED.
• Port LEDs.
• System LEDs.
Smart Switch front panel.
(1000Base-SX/LX)/100M SFP.
factory defaults. To restore the
d LEDs between Ethernet mode LED or
Back Panel
Figure 3-3 illustrates the NETGEAR GS700TPS Smart Switch back panel:
Figure 3-3
3-2 Physical Description
v1.0, April 2009
Page 29
GS700TPS Smart Switch
The back panel contains the following:
• A 100-240VAC/50-60 Hz universal input RS-232 Console interface, which is a standard AC
power receptacle for accommodating the supplied power cord.
• Two 19 pin Gbps HX stacking ports.
LED Designations
This section provides an explanation for the following LED types:
• “Port LEDs”
• “System LEDS”
Physical Description 3-3
v1.0, April 2009
Page 30
GS700TPS Smart Switch
Port LEDs
Table 3-1. The following table describes the port LED designations.Port LEDs
Port LED Designation
24/48-10/100/1000 Ports
- One LED/Port
24/48-10/100/1000 Ports
- One LED/Port
4-SFP Ports - One LED/
Port
Link/ACT LED • Off - No 10/100/1000Mbps link is established on
the port.
lid Green - A valid 1000Mbps link is established
• So
on the port.
ashing Green - Packet transmission or reception
• Fl
is occurring on the port at 1000Mbps.
• Solid Yellow - A valid 10/100Mbps link is
established on the port.
ashing Yellow - Packet transmission or
• Fl
reception is occurring on the port at 10/100Mbps.
PoE Mode • Off - No PoE-powered device (PD) connected.
• Solid Green - The PoE powered device (PD) is
connected and the port is supplying power
successfully.
lid Yellow - Indicates one of the following
• So
failures resulted in stopping power to that port:
• Short circuit on PoE power circuit.
• PoE power demand exceeds power
available.
• PoE current exceeds PD’s
sification.
Clas
• Out of proper voltage band (44-57
).
VDC
SFP Link/ACT LED • Off - No link is established on the port.
• Solid Green - A valid 100/1000Mbps SFP module
link is established on the port.
ashing Green - Packet transmission or reception
• Fl
is occurring on the port at 100/1000Mbps.
System LEDS
The following table describes the port LED designations.
3-4 Physical Description
v1.0, April 2009
Page 31
GS700TPS Smart Switch
Table 3-2. System LEDs
LED Designation
Power LED • Off - Power is disconnected.
lid Green - Power is supplied to the switch and is operating
• So
normally.
FAN LED • Off - FAN is operating normally.
• Solid Yellow - FAN has failed.
MAX POE LED • Off - Indicates that there is at least 8W of PoE power available for
another device.
• Solid Yellow - Indicates that less than 8W of PoE power is available.
ashing Yellow - Indicates the PoE MAX LED was active in the
• Fl
• previous two minutes.
1~48 Port LED mode select LED • Solid Green - LED Mode in Ethernet LED Mode (default).
• Solid Yellow - LED Mode in PoE LED Mode.
Stack ID LED- One Seven
Segment LED Display
Stack Master LED • Off - Switch acts as a slave member in a stack of switches.
Stack Port LED Indicates the Up/Down stacking port LED designations
• Green - Displays Stack ID (1-6).
• Solid Green - Switch acts as a master unit in a stack of switches. The
Stack Master LED is lit if there is an active stack link, and the unit is in
stack mode.
• Off – In
• Solid Green – Indicates the Up/Down stacking port link.
• Flashing Green – Packet transmission or reception is occurring on
the Up/Down stacking port.
dicates the Up/Down stacking port link is down.
Device Hardware Interfaces
This section provides information for the following hardware interfaces:
• “RJ-45 Ports”
• “SFP GBIC Module”
• “Stacking Ports”
• “Factory Defaults Button”
Physical Description 3-5
v1.0, April 2009
Page 32
GS700TPS Smart Switch
RJ-45 Ports
RJ-45 ports are auto-sensing ports. When inserting a cable into an RJ-45 port, the switch
automatically ascertains the maximum speed (10/100/1000 Mbps) and duplex mode (half-or fullduplex) of the attached device. All ports support only Unshielded Twisted-Pair (UTP) cable
terminated with an 8-pin RJ-45 plug.
To simplify the procedure for attaching devices, all RJ-45 ports support Auto Uplink. This
technology allows attaching devices to the RJ-45 ports with either straight-through or crossover
cables. When inserting a cable into the switch’s RJ-45 port, the switch automatically:
• Senses whether the cable is a straight-through or crossover cable.
• Determines whether the link to the attached device requires a “normal” connection (such as
when connecting the port to a PC) or an “uplink” connection (such as when connecting the
port to a router, switch, or hub).
• Configures the RJ-45 port to enable communications with the attached device, without
requiring user intervention. In this way, the Auto Uplink technology compensates for setting
uplink connections, while eliminating concern about whether to use crossover or straightthrough cables when attaching devices.
SFP GBIC Module
The GBIC module bays accommodate standard SFP GBIC modules, such as the AGM731F,
AGM732F , or AGM733 from NETGEAR, allowing fiber connections on the network. The module
bay is a combo port, sharing a connection with an RJ-45 port. Being a combo port, only one type
of connection can be active at any given time. For example, both copper and fiber port cannot be
used at the same time. If both connectors are plugged in at the same time, the fiber port becomes
active.
The SFP GBIC bay accommodates a standard SFP GBIC module.
The following types of SFP ports are supported:
• 1000Base-SX
• 1000base-LX
• 100Base-FX
Stacking Ports
Two dedicated high speed stacking ports, with minimum stacking bandwidth of 20 Gbps
(aggregate, bi-directional) via the device’s HX Stack ports. The GS748TPS is backwards
compatible with existing devices.
3-6 Physical Description
v1.0, April 2009
Page 33
GS700TPS Smart Switch
Factory Defaults Button
The Smart Switch has a Factory default button to enable clearing the current configuration and
returning the device back to the factory settings. This removes all settings, including the password,
VLAN settings and port configurations. If the switches are in a stack, the stacking settings are
cleared by the Factory Defaults Button.
Physical Description 3-7
v1.0, April 2009
Page 34
GS700TPS Smart Switch
3-8 Physical Description
v1.0, April 2009
Page 35
Appendix A
Troubleshooting
This chapter provides information about troubleshooting the NETGEAR Smart Switch. The topics
include the following:
• “Troubleshooting Chart”
• “Additional Troubleshooting Suggestions”
Troubleshooting Chart
The following table lists symptoms, causes, and solutions of possible problems.
Table A-1. Troubleshooting Chart
Symptom Cause Solution
Power LED is off. No power is received. Check the power cord connections for the switch at
the switch and the connected device. Ensure all
cables are used correctly and comply with the
Ethernet specifications.
Link LED is off or
intermittent.
File transfer is slow or
performance degradation
is a problem.
A segment or device is
not recognized as part of
the network.
Port connection is not
working.
Half- or full-duplex setting
on the switch and the
connected device are not
the same.
One or more devices are
not properly connected,
or cabling does not meet
Ethernet guidelines.
Check the crimp on the connectors and make sure
that the plug is properly inserted and locked into the
port at both the switch and the connecting device.
Ensure all cables are used correctly and comply with
the Ethernet specifications. Check for a defective
adapter card, cable, or port by testing them in an
alternate environment where all products are
functioning.
Make sure the attached device is set to autonegotiate.
Verify that the cabling is correct. Ensure all
connectors are securely positioned in the required
ports. Equipment may have been accidentally
disconnected.
v1.0, April 2009
A-1
Page 36
GS700TPS Smart Switch
Table A-1. Troubleshooting Chart
Symptom Cause Solution
ACT LED is flashing
continuously on all
connected ports and the
network is disabled.
A unit is linked to a stack,
but does not join the
stack.
A network loop
(redundant path) has
been created.
The stacking ports of the
new unit are configured
differently from the stack,
or the unit is configured
as a stand-alone unit.
Break the loop by ensuring that there is only one
path from any networked device to any other
networked device.
Remove the unit from the stack. If the stack links are
copper links, push the "Restore to Default" button. If
the stack links are combo links, use the Web
Management to configure the unit as a stackable
unit, with combo links used as the stacking ports.
Additional Troubleshooting Suggestions
If the suggestions in Troubleshooting Chart do not resolve the problem, refer to the
troubleshooting suggestions in this section.
Network Adapter Cards
Ensure the network adapter cards installed in the PCs are functioning correctly and the latest
software driver has been installed.
Configuration
If problems occur after altering the network configuration, restore the original connections and
determine the problem by implementing the new changes, one step at a time. Ensure that cable
distances, repeater limits, and other physical aspects of the installation do not exceed the Ethernet
limitations.
Switch Integrity
If required, verify the integrity of the switch by resetting the switch. To reset the switch,
disconnect the AC power from the switch and then reconnect AC source. If the problem continues,
contact NETGEAR technical support. In North America, call 1-888-NETGEAR. If you are outside
of North America, please refer to the support information card included with your product.
A-2 Troubleshooting
v1.0, April 2009
Page 37
GS700TPS Smart Switch
Auto-negotiation
The RJ-45 ports negotiate the correct duplex mode and speed if the device at the other end of the
link supports auto-negotiation. If the device does not support auto negotiation, the switch only
determines the speed correctly and the duplex mode defaults to half-duplex.
The gigabit port on the Gigabit module negotiates speed, duplex mode, and flow control, provided
that the attached device supports auto-negotiation.
Troubleshooting A-3
v1.0, April 2009
Page 38
GS700TPS Smart Switch
A-4 Troubleshooting
v1.0, April 2009
Page 39
Technical Specifications
Network Protocol and Standards Compatibility
IEEE 802.3i 10Base-T
IEEE 802.3u 100Base-TX,FX
IEEE 802.3ab 1000Base-T
IEEE 802.3z 1000Base-X
IEEE 802.3x flow control
Management
IEEE 802.1Q Static VLAN (Up to 128 ranging from 2 to 4K)
Windows 2000 + XP; Microsoft Explorer 6.0
IEEE 802.1p Class of Service (CoS)
SNMPv3
Appendix B
Interface
24/48-RJ-45 connectors for 10Base-T,100Base-TX and 1000Base-(Auto Uplink™ on all ports).
Four Small Form-factor Pluggable (SFP) slots, supported 1000(1000Base-SX/LX)/100M SFP
LEDs
Per port LEDs: Link Status or PoE Status, Stack Link Status (for stacking-enabled ports)
Per device: Power, FAN, Stack ID, Stack Master, Max PoE
Performance Specifications
Forwarding modes: Store-and-forward
Address database size: 8K media access control (MAC) addresses per system
v1.0, April 2009
B-1
Page 40
GS700TPS Smart Switch
Power Supply
Power Consumption: 235W for GS724TPS
Power Consumption: 530W for GS748TPS
100-240VAC/50-60 Hz universal input
Physical Specifications
Dimensions (H x W x D): GS724TPS: 1.7 x 17.3 x 12.2 / 43 x 440 x 310 (in/mm)
Dimensions (H x W x D): GS748TPS: 1.7 x 17.3 x 17.0 / 43 x 440 x 431 (in/mm)
Weight: GS724TPS: 10.824 / 4.920 (lbs/kg)
Weight: GS748TPS: 16.025 / 7.284 (lbs/kg)
Environmental Specifications
Operating temperature: 0 to 50°C (32 to 122°F)
Storage temperature: -20 to 70°C (28 to 158°F)
Operating humidity: 10-90% maximum relative humidity, non-condensing
Storage humidity: 5-95% maximum relative humidity, non-condensing
Operating altitude: 3,000 m (10,000 ft.) maximum
Storage altitude: 3,000 m (10,000 ft.) maximum
Electromagnetic Emissions
CE mark, commercial
FCC Part 15 Class A
VCCI Class A
C-Tick
FCC Class A
CE Class A
B-2 Technical Specifications
v1.0, April 2009
Page 41
GS700TPS Smart Switch
Electromagnetic Immunity
EN 55022 (CISPR 22), Class A
Safety
CE mark, commercial
UL/cUL listed (UL 1950) / CUL IEC950 / EN60950
Modules
AGM731F 1000Base-SX SFP GBIC for multimode fiber
AGM732F 1000Base-LX SFP GBIC for single mode fiber
AGM733 1000Base-LZ GBIC for long haul single mode fiber
Technical Specifications B-3
v1.0, April 2009
Page 42
GS700TPS Smart Switch
B-4 Technical Specifications
v1.0, April 2009
Page 43
Index
Numbers
1000Base-LX, 1-4
1000Base-SX, 1-4
1000BASE-T, 1-4
1000BASE-X, 1-4
100-240VAC/50-60, 3-3
100BASE-TX, 1-4
10BASE-T, 1-4
1U, 1-5
8-pin, 3-6
A
AC Power, 3-3
AGM731F, 3-6
AGM732F, 3-6
AGM733, 3-6
Applying AC Power, 2-7
Auto Uplink, 3-6
Auto-negotiating, 1-4
Auto-sensing, 3-6
Customer support, 1-ii
D
Default IP Address, 2-7
Duplex Mode, 3-6
F
Factory Default Button, 3-7
Fiber Connectivity, 1-1
Flat Surface, 2-2
Full-duplex, 1-2
G
GBIC, 1-2, 3-6
Gigabit Ports, 1-1
H
High-speed Servers, 1-1
Hz, 3-3
B
Back-pressure, 1-4
Brackets, 2-2
C
Category 5 Unshielded Twisted-Pair, 1-2
Checking the Installation, 2-3
Class of Service, 1-2
Combo Port, 3-6
Combo Ports, 1-4
Connecting Devices to the Switch, 2-4
Copper, 1-1
Crossover, 3-6
I
IEEE 802.3ab, 1-4
IEEE 802.3i, 1-4
IEEE 802.3u, 1-4
IEEE 802.3x, 1-4
IEEE 802.3z, 1-4
IEEE Standards, 1-4
IEEE-compliant, 1-2
Installation Guide, 1-7
Installing an SFP GBIC Module, 2-5
Installing the Switch, 2-2
Internal Power Supply, 1-4
Index-1
v1.0, April 2009
Page 44
GS700TPS Smart Switch
L
LED Designations, 3-3
Link/ACT LED, 3-4
Low Latency, 1-2
M
MAC, 1-4
Media Access Control, 1-4
Mounting Holes, 2-2
N
Nylon Washers, 2-2
O
ON/OFF switch, 2-7
Operating Conditions, 2-2
Operating Environment, 2-1
Operating humidity, 2-2
Overview, 1-1
S
SFP GBIC Module, 3-6
SFP Link/ACT LED, 3-4
SFP Module Bay, 2-5
Site Requirements, 2-1
Smart Switch Resource CD, 1-7
Smart Wizard Discovery, 1-2
Straight-through, 3-6
Support, 1-ii
Support Information Card, 1-7
T
Temperature, 2-2
Traffic Contro l, 1-2
Troubleshooting Chart, A-1
U
User Intervention, 3-6
User’s Manual, 1-7
UTP, 2-4
P
Package Contents, 1-7
Pause Frame Flow Control, 1-4
Phillips Screwdriver , 2-2
Port LEDs, 3-4
Power cord, 1-7
Preparing the Site, 2-1
R
Rack, 2-2
Rack-mount Kit, 1-7, 2-2
registering, 1-ii
RJ-45, 1-2
RJ-45 Ports, 3-6
Rubber Footpad, 2-2
Rubber footpads, 1-7
Index-2
V
Ventilation, 2-2
VLAN, 1-2
W
Warranty, 1-7
Web-based Graphical User Interface, 1-1
v1.0, April 2009
Loading...