Netgear AXM761 Quick Start Manual

)NSTALLATION'UIDE

e

ProSafe 10 Gigabit Ethernet SFP+ Module AXM761

Install Your Optical Module

The 10 Gigabit small form-factor pluggable (SFP+) module provides a full-duplex 10G bps
each direction for Ethernet operation on NETGEAR managed switches.

The switch will automatically detect the AXM761, so you can simply plug it into an
available module slot.

The module can be inserted or removed while the switch is operational.

AXM761

Installing a AXM761 Module

Insert the module firmly into the slot that supports the SFP+ interface. Make sure the optical
cable you use is multi mode LC to LC duplex cable.

AXM761

Removing a AXM761 Module

Release the module latch by pulling down the handle bar across the module, and pull the
module out of the module slot.

Technical Specifications

Standards IEEE 802.3ae 10GBase-SR

Wavelength 850nm

Dimensions (HxWxD) 0.46” x 0.53” x 2.19”

(11.9 mm x 13.7 mm x 55.7 mm)

Weight 17.1g

Operating Temperature 32 -158º F (0 - 70ºC)

Storage Temperature 32 -185 ºF (0 - 85ºC)

Operative relative humidity 85% @ (25ºC)

Operating Distance 2 - 300 m for 50/125 um MMF

2 - 33 m for 62.5/125 um MMF

Connectors LC

Power Consumption <1.0w

MTBF 4,986,536 hr (569 years)

Safety Certification UL 1950 CSA 22.2 No. 950

Environmental Compliance -RoHS

AXM761_IG_10July09.fm Page 1 Friday, July 10, 2009 2:36 PM

July 2009

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,
this product should be treated and recycled in accordance with the laws of your jurisdiction implementing
the WEEE Directive.

© 2009 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of
NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice.

Technical Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and use it
to register your product at http://www.NETGEAR.com/register. Registration is required
before you can use our telephone support service. Registration via our web site is strongly
recommended.

Go to http://kbserver.netgear.com for product updates and Web support. For Warranty and
Regional Customer Support information, see the Warranty Card that came with your
product.

Regulatory Compliance

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability,
NETGEAR reserves the right to change the product described in this document without
notice. NETGEAR does not assume any liability that may accrue due to the use or
application of the product(s) or circuit layout(s) described herein.

Certificate of Manufacture/Importer

It is hereby certified the NETGEAR model AXM761 has been suppressed in accordance
with the condition set out in MBPT-Amtsb|Vfg 243/1991 and vfg 46/1992. The operation of
some equipment (for example, test transmitters) in accordance with regulation may,
however, be subject to certain restrictions. Please refer to the note in the operating
instructions. Federal Office for Telecommunications Approvals has been notified of the
placing of this equipment on the market and has been granted the right to test the series for
compliance with regulation.

Note: This device has been tested and found to comply with limits for a Class B digital

device, pursuant to part 15 of FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a commercial installation.

Laser Safety Warning

This is a Class 1 laser product.

Warning: Because invisible laser radiation may be emitted from aperture of the port when

no fiber cable is connected, avoid exposure to laser radiation and do not stare into
the open aperture.

AXM761_IG_10July09.fm Page 2 Friday, July 10, 2009 2:36 PM