Netgear AX742 Quick Start Manual
Installation Guide
e
ProSafe 24 Gigabit Ethernet Stacking Kit AX742
This product is used as a stacking link between two NETGEAR managed switches
that have auxiliary module slots such as the GSM7328S, GSM7352S, GSM7328FS,
and M5300 series switches. Each module can operate at 12 Gbps (half duplex) or
24 Gbps (full duplex). Two AX744 modules and a CX4 cable are provided to allow
connection between two switches.
Verify the Package Contents
• Two ProSafe® 24 Gigabit Ethernet AX744 modules
• One 1 m CX4 cable
• Installation guide
.
AX744AX744
CX4 cable
Installation guide
Install a Module
The ProSafe 24 Gigabit Ethernet AX744 module fits into the module slot in
NETGEAR stacking switches. The module is set to stacking mode by default. See
the switch CLI or software administration manual for instructions to configure the
switch for use with the module.
The module bays are on the front or the rear panel of a switch depending on the
switch model.
Note: The AX744 module is not hot swappable. You must reboot the switch after
installing or removing a module.
To install a module:
1. Insert the module into one of the available module slots, pressing firmly to seat
the module.
2. Once the module is seated, tighten the two set screws to hold the module in
place.
3. Reboot the switch.
AX744
Module
slots
Remove a Module
Note: The AX744 module is not hot swappable. You must reboot the switch after
installing or removing a module.
To remove a module:
1. Loosen the two set screws on either side of the module front panel.
2. Remove the module by holding the screw posts and pulling evenly on the
module and sliding it out of the module slot.
3. Reboot the switch.
Connect Switches with the Stacking Cable
To connect two switches with the CX4 cable:
1. Insert one end of the CX4 cable provided into an AX744 module that has been
installed in one switch.
2. Insert the other end of the CX4 cable into an AX744 module installed in a
second switch.
3. Refer to the software administration guide for the host switch for instructions to
configure the switch for use with the AX744 module.
AX742v1h3_IG_2oct2012.fm Page 1 Thursday, October 4, 2012 11:03 AM
October 2012
This symbol appears in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE directive). If you dispose of this product in the
European Union, treat and recycle it in accordance with your jurisdiction’s laws that implement the
WEEE directive.
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to
change without notice. Other brand and product names are registered trademarks or trademarks of their
respective holders. © NETGEAR, Inc. All rights reserved.
For indoor use only in all EU countries and Switzerland.
For the complete EU Declaration of Conformity, visit
http://support.netgear.com/app/answers/detail/a_id/11621/.
Statement of Conditions: In the interest of improving internal design, operational function, and/or reliability,
NETGEAR reserves the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Specifications
Specifications
Standard IEEE 802.3ak, 10GBASE-CX4
Dimensions (H x W x D) 1.20 in. x 2.92 in. x 6.13 in.
(30.5 mm x 74.1 mm x 155.7 mm)
Weight 0.317 lb (0.144 kg)
Operating temperature 32 –122ºF (0 – 50ºC)
Storage temperature 32 – 158ºF (0 –70ºC)
Operative relative humidity 10 – 90% noncondensing
Max. power consumption 0W
MTBF 885 years (at 25ºC); 252 years (at
55ºC)
Regulatory Compliance
Certificate of Manufacturer/Importer
It is hereby certified that the NETGEAR model AX744 has been suppressed in
accordance with the condition set out in MBPT-Amtsb|Vfg 243/1991 and vfg 46/
1992. The operation of some equipment (for example, test transmitters) in
accordance with regulation may, however, be subject to certain restrictions. Please
refer to the note in the operating instructions. Federal Office for Telecommunications
Approvals has been notified of the placing of this equipment on the market and has
been granted the right to test the series for compliance with regulation.
Note:This device has been tested and found to comply with limits for a Class A digital
device, pursuant to part 15 of FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a commercial installation.
Technical Support
After installing your device, locate the serial number on the label of your product and
use it to register your product at https://my.netgear.com.
You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website.
For product updates and web support, visit http://support.netgear.com.
You can get the hardware and software manuals for managed switches online at
http://downloadcenter.netgear.com or through a link in the switch user interface or
resource CD.
AX742v1h3_IG_2oct2012.fm Page 2 Thursday, October 4, 2012 11:03 AM
Loading...