Nemco 56050 Installation Manual

56050 - ( ) CanPRO

Important

1. To get the best operation and life from your machine, please read and comply with these instructions.

2. Clean machine thoroughly before and after each use using cleaning instructions below.

3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.

4. If unit fails to work properly when first operated call NEMCO customer service at 1-800-782-6761

Operation of CanPRO

1. Set side handle #20 in the unlock position.

2. Place can on the Table Base Can Sitter and gently lower the U-shaped pin of the Cutter Housing Assembly #41 is over the lid. Be sure

that the can is against the face of the can opener.

3. Turn Top Handle #4 in a CLOCK-WISE direction to open can. Warning: Over-rotating beyond the initial seam cut may cause metal

slivers. Incision point may be sharp. Train operators when to stop cutting and how to remove lid safely.

To Clean

WARNING: Cutting area must be kept clean at all times as indicated in the "CLEANING INSTRUCTIONS – USE OF BRUSH." Inspect and
clean the cutter and gripper with the included brush after each use to ensure proper operation. Failure to follow the included "Cleaning
Instructions" will cause damage and VOID WARRANTY.

Disassemble for Cleaning.

1. UNLOCK SIDE HANDLE #20. Slightly press Gripper Housing #7 face to pull out Side Locking Pin #16.

2. Tilt back Gripper Housing #7.

3. IMPORTANT: Pull out Cutter Housing Assembly #41 and clean with brush. Use brush provided to clean around outside of Cutter

Housing and inside the Mechanism Housing. Also use brush to clean all debris from around the Gripper.

4. After cleaning with brush, rinse off residue. SEE SEPARATE “CLEANING INSTRUCTIONS – USE OF BRUSH” FOR LOCATIONS.

Reassemble.

5. Insert Cutter Housing Assembly #41.

6. Return Gripper Housing #7 to closed position.

7. Slightly press Gripper Housing #7 face to re-insert the Side Locking Pin #16. (Ensure side handle #20 is unlocked.)

1. If cleaned in DISHWASHER, disassemble and clean with brush per above instructions.

OPERATING INSTRUCTIONS

Recommended Handle Turns:

Can Size Diameter Handle Turns

#2 3" 3 Revolutions
#5 5" 5 Revolutions

#10 6" 6 Revolutions

Note:

2. Proper cleaning maximizes the life of the parts.

Replacing Cutter from Cutter Housing Assembly

1. Hold Cutter Shaft #26 with wrench and loosen Cutter Locking Bolt #31 (left hand thread) with another wrench by turning clockwise.

2. Remove Cutter Washer #30 and Cutter Spacer #29 and Cutter #28.

3. Replace with new Cutter.

4. Reverse steps 2 and 1 to re-assemble.

CanPro Replacement Parts
Model Numbers : 56050- ( )

No. Part # Description

1 56030 Top Handle Knob Cover
2 56031 Top Handle Knob
3 56032 Top Handle Knob Screw
4 56033 Top Handle
5 56034 Handle Screw
6 56027 Top Handle Bearing
7 56035 Gripper Housing
8 56036 Gripper Shaft
9 56028 Gripper
10 56037 Bushing
11 56038 Bushing
12 56039 Locking Mechanism
13 56040 Locking Pin
14 56041 Allen Set Screw
15 56042 Gripper Housing Spring
16 56217 Side Locking Pin
17 56044 Bushing
18 56045 Bushing
19 56046 Side Handle Shaft
20 56216 RH Side Handle
21 56048 Mechanism Housing
22 56049 Ball End Set Screw
23 56051 Adjusting Nut

No. Part # Description

24 56052 Rubber Depth Control
25 56053 Adjusting Screw
26 56054 Cutter Shaft
27 56055 Cutter Housing
28 56029 Cutter
29 56024 Cutter Spacer
30 56056 Cutter Washer
31 56057 Cutter Locking Bolt
32 56058 Rubber Pipe Bumper
33 56059 Square Pipe
34 56060 Plastic Pipe End
35 56026 Side Locking Pin Chain
36 56070 Table Base Assembly
38 56063 Under Clamp
39 56064 Table Base Screw
40 56065 Anti-Slip Rubber Pad
41 56022 Cutter Housing Assembly
42 56023 Under Clamp Assembly
43 56068 Side Pin Assembly
44 56214 Bottom Cutter Bearing
45 56213 Top Cutter Bearing
46 56215 Gripper Bearing