NEFF T2596NOAU, T2596NO Installation Instructions Manual
This cooktop is approved for use with Natural and Propane gases
Leave these instructions with the owner
COOKTOP MODEL
T2596NOAU
MAKERS WARRANTY
Installation instructions
User instructions
Part No: W1980
Version B - 2006
2 23
This appliance is imported and distributed by:
For service to this appliance
Please contact:
Sampford & Staff P/L
52-70 Sparks Avenue
Fairfield, Vic, 3078
Phone: 1300 727 421
Email service@sampford.com.au
Contents 3
Introducing your cooktop 4-6
❍ Dear customer
❍ Accessories
❍ Notes on disposal
❍ Gas supply
❍ Electrical supply
❍ What to do if you smell gas
❍ Safety considerations
Installation instructions 7-11
❍ Installer instructions
❍ Statutory requirements
❍ Overall dimensions
❍ Preparing to install
❍ Overhead clearances
❍ Side clearances
❍ Bottom clearance and heat barrier
❍ Bench top specifications
❍ Special considerations for installation over
under bench oven
❍ Installation procedure
❍ Electrical connection
❍ Gas connection
❍ Energy consumption
Gas conversion instructions 12-13
❍ Boiling burners main injector conversion
❍ Boiling burners turn down injector
conversion
❍ Outer wok burner main injector
conversion
❍ Inner wok burner main injector
conversion
User instructions 14-17
❍ Important information
❍ Burner location and control panel
❍ Boiling burners operation and ignition
❍ Wok burner assembly
❍ Wok burner operation
❍ Ventilation requirements
Data plate
3
Contents
22
❍ Additional pan supports
❍ Recommended pan diameters
❍ Cooking recommendations
Do not & Do 18
Cleaning 19
Maintenance trouble shooting 20
Service 21-23
❍ To remove the hob
❍ To service gas control valves
❍ To replace the thermocouple
❍ To replace the electronic ignition module
❍ To replace internal wiring and the gas
control ignition micro switch
❍ Wiring diagram
❍ Data plate
❍ For service to this appliance
Wiring diagram
4
Dear customer
We thank you and congratulate you on your choice.
This carefully designed product, manufactured with the highest
quality materials, has been carefully tested to satisfy all your cooking
demands.
We therefore request that you read and follow these easy
instructions which will allow you to obtain excellent results right
from the start.
The cooktop is fitted with four boiling burners (one large, two medium and one simmer burner) and a wok burner. All burners are
fitted with electronic spark ignition and flame failure device. The
wok burner is supplied with a supplementary wire pan support for
smaller pans. An additional wire pan support is supplied to fit
over the boiling burner pan supports to support small vessels such
as a coffee pot.
The cooktop’s data plate is accessible even with the cooktop fully
installed. It is positioned on the bottom of the unit. A duplicate
copy is supplied at the back of the instruction booklet. Always
quote the details from it to identify the appliance when ordering
spare parts or requesting a service.
In case of a malfunction, turn off the cooktop’s gas supply
before contacting the service centre for assistance.
Only an authorised person should connect and service
this appliance.
Accessories.
❍ Wok support trivet.
❍ Coffee pot support.
Notes on disposal
❍ Old appliances still have some residual value. An environ-
mentally friendly method of disposal will ensure that valuable
raw materials can be recovered and used again.
Before you dispose of your old appliance, make sure that it
has been rendered inoperable.
❍ Your new cooker was protected by suitable packaging while it
was on its way to you. All materials used for this purpose are
environmentally friendly and suitable for recycling. Please make
a contribution to protecting the environment by disposing of
the packaging appropriately.
Gas supply
Check that the data plate shows the appliance is suitable for the
available gas supply.
21
Warning:
Disconnect power and
gas supply before
servicing the unit.
Introducing your cooktop Service
Service and maintenance must only be carried out by an authorised person.
To replace parts such as injectors, gas control valves and ignition
switches, the ceramic hob, pan support, burner caps and burner
heads must be removed. The boiling burner heads are secured
with 2 fastening and the wok burner with 3 fastening screws.
To remove the hob:
1. Close isolation valve.
2. Remove the control knobs, anti-spillage gaskets, pan supports,
burner caps and burner heads.
3. Using a flat bladed tool lift the
ceramic top and remove. Store
the ceramic top in a safe place.
To service gas control valves
Access to burner compartments is as per ’to remove the hob’. The
gas control valves are secured to the gas manifold by means of a
clamp fixed via two screws.
1. Remove the screws which secure the gas valve to the gas manifold.
2. Replace the defective part.
3. Replace in reverse order and open isolation valve.
To replace the thermocouple
Access to burner compartments is as per ’to remove the hob’.
1. Remove the retaining ring securing the thermocouple.
2. Remove connection from electronic ignition module.
3. Replace defective part.
4. Replace in reverse order.
To replace the electronic ignition module
Access to burner compartments is as per ’to remove the hob’.
1. Remove the metal cover.
2. Disconnect the leads from the thermocouples.
3. Loosen the 2 securing screws.
4. Replace in reverse order.
To replace internal wiring and the gas control ignition
micro switch
Access to burner compartments is as per ’to remove the hob’.
1. Disconnect wiring between ignition module and gas control.
2. Disconnect microswitch from gas control.
3. Replace in reverse order.
Loading...