Nec VT40 QUICK SETUP GUIDE

M

RCE A

RGB

INPUT

OUTPUT

AUD

IN

OUT

PC-CONTROL S-VIDEO VID

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

SELECT

POWER

STATUS

ON

/

STAND BY

SOURCE AUTO ADJUST

Quick Connect Guide

RGB

INPUT

OUTPUT

AUDIO

IN

INOUT

OUT

PC-CONTROL S-VIDEO VIDEO

RGB INPUT

RGB OUTPUT

RGB

INPUT

OUTPUT

AUD

IN

OUT

PC-CONTROL S-VIDEO VID

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

SELECT

POWER

STATUS

ON

/

OFF

SOURCE AUTO ADJUST

RGB
INPUT

OUTPUT

AUD

IN

OUT

PC-CONTROL S-VIDEO VID

MultiSync VT Series LCD Projectors

Step 1

Step 2

Connect the supplied 15pin-15pin signal cable.

For older Macintosh computers,
use the supplied pin adapter to
connect to your Macintosh's video
port.

Always power down before

Monitor

you hook up.

Connect the supplied power cable.

Step 4

Set up the Projector.

To adjust the projector's focus or to zoom in and out use the Focus ring or Zoom
lever on the lens.

Focus ring

Zoom lever

Adjusting the Tilt Foot

1

. Press and hold the Tilt button on the front of the projector.

2

. Lift the front edge of the projector to the desired height, and release the button to lock

the Adjustable Tilt Foot.

To fine-tune the image's position vertically on the screen, rotate the foot. Each of the rear
feet height can be changed up to 0.6" (4 mm).

Step 3

Turn on the projector.

Power button

NOTE: To turn off the projector, press and hold the

POWER button for a minimum of two seconds.

• If the projected image does not appear square to the screen then use keystone correction
for proper adjustment.

Printed in Japan

78038752

Basic Menu
Source Select
Picture
Volume
Image Options
Menu
Setup
Help

Source Select
RGB

Video
S-Video

Image Options
Keystone
Color Temperature
Lamp Mode

High-Bright / Eco

Volume

Contents

Basic / Advanced
English/German/French/Italian/Spanish/Swedish/Japanese
Pointer 1- 8
On / Off

On / Off

Front Floor / Rear Ceiling / Rear Floor / Front Ceiling
Blue / Black / Logo

Menu
Menu Mode
Language
Projector Pointer
Source Display

Volume Bar

(

Direct Button

)

Setup
Orientation
Background

Help
Contents

Information

Pege 1

(

Source Name / Input Terminal /
Horizontal Frequency /
Vertical Frequency / Sync Polarity

)

Pege 2(Signal Type/Video Type/Sync Type /
Interlace / Resolution

)

Page 3(Aspect Ratio / Gamma Correction /
Noise Reduction / Color Matrix /
Matrix Type)
Page 4(Lamp Hour Meter / Projector Usage

)

Picture
Brightness

Contrast
Color
Hue
Sharpness

Basic Menu Remote Control Features

SELECT

Vol.

Vol.

POINTER

POWER

HELP

RD-366E

PIC.

MUTE

MAGNIFY

SOURCE

AUTO

ADJ.

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

(12)

)

(

1

(

)

3

(

)

5

)

(

7

(

)

8

(10)

(1)

Source Button

Press to select a video source.

(2)

Auto Adjust Button

Use this button to adjust Position-H/V and
Pixel Clock/Phase for an optimal picture.

(3)

Menu Button

Displays the menu.

(4)

Select ( ) / Volume (+) (–)
Buttons

:Use these buttons to select the

menu of the item you wish to adjust.

:Use these buttons to change the

level of a selected menu item.
A press of the button executes the
selection. When no menus appear, these

buttons work as a volume control.

When the pointer is displayed, these

buttons move the pointer.

(5)

Enter Button

Use this button to enter your menu
selection.

NOTE : The POWER, SOURCE. AUTO ADJ., MENU, SELECT, ENTER and CANCEL buttons

on the remote control perform the same functions as the corresponding buttons on the
projector cabinet. The remaining buttons are on the remote control only.

(

(

(
(

(

2

4

6
9

11

)

)

)
)

)

(6)

Cancel Button

Press this button to exit “Menus”. Press
this button to return the adjustments to the
last condition while you are in the
adjustment or setting menu.

(7)

Magnify Button

Use the (+) or (–) button to adjust the
image size up to 400%. When the Pointer
is displayed, the magnified image is
displayed at the center of the Pointer.
When the Pointer is not displayed, the
magnified image is displayed at the center
of the screen.
When the image is magnified, the pointer
is changed to the magnifying icon.

(8)

Pointer Button

Press this button to display one of the
eight pointers; press again to hide the
pointer. You can move your pointer icon to
the desired area on the screen using the
Select button.

(9)

Picture Mute Button

This button turns off the image and sound.
Press again to restore the image and
sound.

(10)

Help Button

Provides information about operation and
adjustment procedures, the set-up
information for the current menu and
adjustment information during menu
operation. This also displays information
on how to use the Help menu.

(11)

Power Button

Use this button to turn your projector on
and off.

NOTE: To turn off the projector, press and

hold the Power button for a minimum of
two seconds.

(12)

Infrared Transmitter

Direct the remote control toward the
remote sensor on the projector cabinet.