NEC V221W-BK, V221W User Manual
V191W
V221W
User’s Manual
Index
Warning, Caution .........................................................................................................................English-1
Registration Information ...............................................................................................................English-1
Contents ....................................................................................................................................... English-3
Quick Start ...................................................................................................................................English-3
Controls ........................................................................................................................................ English-6
Recommended use ......................................................................................................................English-9
Specifications - V191W .............................................................................................................. English-11
Specifications - V221W ..............................................................................................................English-12
Features .....................................................................................................................................English-13
Troubleshooting .........................................................................................................................English-14
TCO’03 ....................................................................................................................................... English-15
Manufacturer’s Recycling and Energy Information .................................................................... English-16
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
Plug Type North America
European
Continental
U.K. Chinese Japanese
English
Plug Shape
Country
Voltage
*When operating the V191W/V221W monitor with its AC 125-240V power supply, use a power supply cord that matches the
power supply voltage of the AC power outlet being used.
NOTE: This product can only be serviced in the country where it was purchased.
U.S.A./Canada U.K. China JapanEU (except U.K.)
120* 230 220 100230
Registration Information
Declaration
Declaration of the Manufacturer
We hereby certify that the colour monitors
V191W (TFT185W80PS)/V221W (TFT22W90PS)
are in compliance with:
Council Directive 2006/95/EC:
– EN 60950-1
Council Directive 2004/108/EC:
– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
and marked with
NEC Display Solutions, Ltd.
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan
English-1
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the V191W/V221W color monitor so as not to interfere with radio and television
reception.
(1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,
and meet the following condition.
Power supply cord Non shield type, 3-conductor
Plug shape
U.S.A
(2) Please use the supplied shielded video signal cable, 15-pin mini D-SUB to D-SUB cable or DVI-D to DVI-D cable.
Use of other cables and adapters may cause interference with radio and television reception.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,
Washington, D.C., 20402, Stock No. 004-000-00345-4.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address: 500 Park Blvd, Suite 1100
Itasca, Illinois 60143
Tel. No.: (630) 467-3000
Type of Product: Display Monitor
Equipment Classification: Class B Peripheral
Models: V191W (TFT185W80PS)
V221W (TFT22W90PS)
We hereby declare that the equipment specified above conforms
to the technical standards as specified in the FCC Rules.
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.
ENERGY STAR is a U.S. registered trademark.
ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,
Norway, Spain, Sweden, U.K.
All other brands and product names are trademarks or registered trademarks of their respective owners.
As an ENERGY STAR® Partner, NEC Display Solutions of America, Inc. has determined that this product meets the ENERGY STA R
guidelines for energy efficiency. The ENERGY STA R emblem does not represent EPA endorsement of any product or service.
English-2
Contents
Your new NEC LCD monitor box* should contain the following:
• LCD monitor with tilt base
• Power Cord
•Video Signal Cable
• Setup Manual
• CD-ROM (only EU)
• Base Stand
• Stand Neck
Setup
Manual
English
Setup Manual
*
Remember to save your original box and packing material to transport or ship the monitor.
(Type of power cord included will
Power Cord
depend on the where the LCD
monitor is to be shipped)
Video Signal Cable LCD monitor
CD-ROM
(only EU)
Quick Start
To attach the Neck/Base to the LCD monitor.
1. Insert the front of the Stand neck into the holes in the front of Base stand.
The snapping tabs on the Base stand should fit into the hole on the Stand neck
(Figure S.1).
2. Insert the front of the Stand neck into the holes in the LCD monitor.
The snapping tabs on the LCD monitor should fit into the hole on the Stand neck
(Figure S.1).
To attach the LCD monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable
connected with the monitor to the connector of the display card in your system
(Figure A.1). Tighten all screws.
For the Mac: Connect the Macintosh cable adapter (not included) to the computer.
Attach the 15-pin mini D-SUB signal cable to the Macintosh cable adapter
(Figure A.2). Tighten all screws.
NOTE: Some Macintosh systems do not require a Macintosh cable adapter.
Macintosh Cable Adapter
(not included)
(Stand not connected)
LCD monitor
Stand neck
Base stand
Figure S.1
Figure A.1
Figure A.2
English-3
3. Connect one end of the power cord to the monitor and the other end to the power outlet (Figure B.1).
NOTE: Please confirm that the tabs are completely secure.
NOTE: Please refer to Caution section of this manual for proper selection of power cord.
4. Turn on the monitor with the front power button and the computer (Figure C.1).
18˚ Tilt
Power Cord
D-Sub
Power Button
Figure B.1 Figure C.1
5. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings.
For further adjustments, use the following OSD controls:
• Image Setup
• Image Position
Refer to the Controls section of this User’s Manual for a full description of these OSD
controls.
NOTE: If you have any problem, please refer to the Troubleshooting section of this
User’s Manual.
Tilt
Grasp both sides of the monitor screen with your hands and adjust the tilt as desired
(Figure TS.1).
Remove Monitor Stand for Mounting
To prepare the monitor for alternative mounting purposes:
1. Disconnect all cables.
2. Place monitor face down on a non-abrasive surface (Figure R.1).
3. Insert the thin rod into the hole in the back of LCD monitor and using your thumbs, press the tabs on the back side of base
stand in the direction of the arrows the pull out the stand as indicated (Figure R.1)
4. Connect the AC cord to the back of the monitor (Figure R.2).
5. Reverse this process to re-attach stand.
NOTE: Use only VESA-compatible alternative mounting method.
Figure TS.1
NOTE: Handle with care when removing monitor stand.
Tabs
Non-abrasive surface
Figure R.1
Figure R.2
English-4
Loading...