NEC NWTL656, NWTL456 User Manual
NWTL656
User manual
WASHER SAFETY
Save these instructions
To reduce the risk of fire, electrical shock, or injury when using your washer, adhere to the
following basic precautions.
Read all instructions before using your washer
Flammable fluids (dry cleaning solvents,
kerosene, gasoline etc.) should not be
used or stored on or near your washer.
Do not add flammable fluids to your wash
water. These substances give off
vapours that can create a fire hazard or
explosion.
The appliance is not intended for use by
young children or infirm persons without
adequate supervisions.
Young children should be supervised to
ensure they do not play with the
appliance.
After starting a washing cycle, do not
reach into the spin basket until all motion
has stopped.
Do not tamper with the controls.
If the appliance is supplied from an
extension cord set or electrical portable
outlet device, it should be positioned so it
is not subjected to splashing or ingress
moisture.
If the supply cord is damaged, it must be
replaced by the manufacturer or qualified
service agent in order to avoid any
potential hazard.
Please….
Have only a qualified person install,
repair, or replace parts on the washer.
Maintain washer properly.
Protect washer from the weather and
keep it where the temperature will not fall
below freezing.
Do no install the washer at a place of
extremely high humidity. It could cause
an electrical shock or a short circuit.
Connect washer to the correct outlet,
electrical supply, water supply, and drain
supply.
Ground washer properly.
Understanding your responsibilities
Do not use chlorine bleach and ammonia or acid (such as vinegar or rust remover) in the
same wash. Hazardous fumes can form.
Do not wash fibreglass materials. Small particles can stick to fabrics washed in following
loads and cause skin irritation.
Do not use hot water if standard temperature is over 50C (122F). It could cause
deformation of plastic parts.
Do not spray water on the control panel and back cover of the washer. It could cause fire
or electric shock.
In case of the dual valve model, if you can connect the cold-water inlet only, while the
temperature is selected as hot or warm, there can be water leakage from the
unconnected water valve.
CONTENTS
Washer Safety……………………………………………………………………….………..………………....…2
Contents……………...………………………………………………………………………..……………...…....3
Components / Parts and Accessories……………………………………………..…….……………………....4
Points for Attention…………………………………………………………………………………………….…...5
Installation………………………………………………………………………………….….…………….……...6
Installation……………………………………………………………………………….…………………….........7
Installation……………………………………………………………………………..……..……………….........8
Operating the washer……..………………………………………………………..…..……………………..…..9
Control Panel………………………………….……………………………………………..………………...…10
Preparation of Laundry and use of Detergents…………………………………………..…………………...11
Hints and Tips ………………………………………………………………..………………………………......12
Cleaning and Maintenance………………………………………………………………………………..........13
Cleaning and Maintenance………………………………………………………………………………..........14
Cleaning the Filters………………………………………………………………………….………...….….......15
Removing Stains / Specifications...……………………………………………………..……………...…...….16
Handling of Common Breakdowns……………………………………………………………………...…...…17
• Read this Manual carefully and thoroughly before using the machine. Before using the
machine, you should for safety concerns make sure that the socket is provided with effective
earth connection. The manufacturer will not accept responsibility for problems arising from
non-compliance with the Manual.
• You are advised to read the Manual carefully so as to use the washer in a correct manner.
• After reading, please keep the Manual properly for future reference.
• All invoices and warranty certificates must be kept properly after purchase, as they serve as
an important basis for provision of services by the NEC.
COMPONENTS AND PARTS
Lid
Lid Handle
Water Inlet
Detergent
Dispenser
Lint Filter
Washing Tub
Bleach Inlet
Wave Plate
Control Panel
Plastic Base
Water Inlet Hose
Window
Power Supply
Plug
Softener Inlet
Handle
Base Board
Drain Pipe
ACCESSORIES
Water intake pipe Drain pipe Base board
1 set (cold water) 1 piece 1 piece 1 piece
Coupling
(optional)
stor Lever
240v 110v
POINTS FOR ATTENTION
Do not allow power supply cables to be damaged,
bent, strained or twisted to excess, tied up or
transformed, nor load them with weights or put
weights in between them. The user must never
employ power supply cables/plugs which have been
damaged or sockets which have come loose. All
power supply cable replacements should be referred
to your NEC Service Centre.
Before washing items, please empty loose objects e.g.
coins, from items.
Fit power supply cables into AC 230V special sockets
with good earthing.
To prevent deformation of plastics, do not use hot
water with a temperature over 50°C for washing.
Do not put in waterproof or down fabrics for washing.
Do not stand on the machine or place heavy objects
on it
Unplug the machine and turn off water tap when not
using the machine.
Please do not attempt to operate the washing
machine with the lid open.
Make sure that water tap is turned on and water inlet
pipe well connected during wash.
90cm
60cm
1.5m
INSTALLATION
CONNECTION OF DRAIN HOSE
• Direct drain hose at the washer drain outlet
until it is completely encased by the outlet.
• Check if the connection is secured.
Less than
8cm
DOWNWARD DRAIN WASHER (FOR NON
PUMP MODELS)
• The height should not exceed 8cm.
• For an extension hose, please use a pipe of
over 3cm inner diameter and less than 1.5m
in length.
• Do not place the drain hose nozzle in water.
UPWARD DRAIN WASHER
• To prevent water from flowing backwards, the
drain pipe should be 60-90cm above ground.
• Place the end of drain pipe in washing tub and
fasten the pipe so that it might not come loose
under water pressure or with interference by
children at play.
• Use the U-shaped drainage system beneath
washing tub. Drain pipe must be 60-90cm above
ground.
ADJUSTMENT OF DRIANAGE DIRECTION
• Remove the fixing screw of the drain hose
nozzle and push the nozzle in.
• When lying the washer down, be sure not to
damage the power supply cable and the
coupling.
• Extricate the inner drain hose from the drain
hose clip at the back.
• Push down the tightly closed cap over the fixed
nozzle opposite
and place it on the side which has been left
empty.
• Turn the drain hose nozzle to the fixed nozzle
opposite.
• Fix the drain hose nozzle with a screw.
• Insert the drain hose into the fixed hose clip.
ATTENTION
Do not worry when you open the washer to find
water accumulated in it. This has come from the
test which each washer has to go through before
leaving the factory.
NOTE: The instructions for appliances connected to the water mains shall state
• the maximum inlet water pressure, in pascals
• the minimum inlet water pressure, in pascals, if this is necessary for the correct operation of the appliance, the instructions
for appliances connected to the water mains by detachable hose sets shall state that the new hose-sets supplied with the
appliance are to be used and that old hose sets should be used.
Loading...