Page 1
Installation and Assembly - Universal Ceiling Mount
Model: NP01UCM
Maximum Load Capacity: 50 lb (22.7 kg)
Read instruction sheet before you start inst allation and assembly.
WARNING
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and
components.
IMPORT ANT! Be sure not to touch the projector while tightening the set screw on the
ball and socket mount. This may cause the image to be unaligned when you let go.
IMPORT ANT! T urn to the appropriate page for your ceiling inst allation.
Applications:
Flush Mount.................................................................................................................................................. page 7
Extension Column........................................................................................................................................ page 8
Installations:
To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings........................................................................................ page 5
T o Concrete Ceilings.................................................................................................................................... page 6
Visit the NEC Web Site at www.necsam.com
1 of 9
ISSUED: 04-11-06 SHEET #: 055-9458-2 05-09-06
For customer care call 1-800-729-0307 or 708-865-8870.
Page 2
Compatability Chart
for NEC Projectors
Manufacturer Model Manufacturer Model
NEC HT410 NEC MT1035
NEC HT510 NEC MT1035+
NEC GT1150 NEC MT830
NEC GT2150 NEC MT830+
NEC GT5000 NEC MT1040
NEC GT6000 NEC MT1045
NEC GT6000R NEC MT840
NEC GT2000 NEC MT850
NEC GT2000R NEC MT1050
NEC GT950 NEC MT1055
NEC LT10 NEC MT1056
NEC LT140 NEC MT860
NEC LT84 NEC MT1060
NEC LT150 NEC MT1060R
NEC LT150z NEC MT1065
NEC LT75 NEC Multisync LT245
NEC LT75z NEC NP1000
NEC LT85 NEC NP2000
NEC LT154 NEC V37
NEC LT155 NEC LT380
NEC LT156 NEC VT440
NEC LT157 NEC VT440K
NEC LT158 NEC VT540
NEC LT170 NEC VT540K
NEC LT180 NEC VT650
NEC LT220 NEC VT45
NEC LT240 NEC VT45K
NEC LT240K NEC VT46
NEC LT245 NEC VT460
NEC LT260 NEC VT465
NEC LT260K NEC V47
NEC LT265 NEC VT560
NEC LT280 NEC VT660
NEC LT35 NEC VT660K
NEC HT1000 NEC VT770
NEC HT1100 NEC VT47
NEC MT1000 NEC VT470
NEC MT1020 NEC VT480
NEC MT810 NEC VT48
NEC MT820 NEC VT570
NEC MT1030 NEC VT575
NEC MT1030+ NEC VT580
NEC VT670
NEC VT676
NEC WT600
Visit the NEC Web Site at www.necsam.com
2 of 9
ISSUED: 04-11-06 SHEET #: 055-9458-1
For customer care call 1-800-729-0307 or 708-865-8870.
Page 3
Before you start check the parts list to insure all of the parts shown are included.
Parts List
Description Qty. Part Number
A ball and socket mount 1 055-0016
B 4 mm security allen wrench 1 560-9646
C M5 x .8 x 10 mm socket pin type F screw 1 520-2031
D #10-32 x 3/8" spade thumb screw 1 560-2107
E #10-32 x 3/8" serrated washer head socket pin screw 1 520-2151
F #14 x 2.5 phillips hex head wood screw 2 5S1-015-C04
G ceiling plate 1 580-4042
H .25" ID x .56" OD x .26 spacer 2 590-2071
I extension column connector with cord management 1 580-4025
J #10-32 x 3/8" socket pin screw 2 520-2084
K #10-32 x 3/16" slotted set screw 3 520-2187
L adapter plate 1 055-0614
M M3 x 8 mm serrated washer head socket pin screw (not shown) 4 510-2004
N M4 x 10 mm serrated washer head socket pin screw (not shown) 4 510-2060
O M5 x 10 mm serrated washer head socket pin screw (not shown) 4 510-2063
P M6 x 10 mm serrated washer head socket pin screw (not shown) 4 510-2066
Q 2 mm security allen wrench 1 560-1097
R washer 4 540-2025
A
I
L
Note: Actual parts may appear slightly different than illustrated.
G
C
J
D
R
K
B
FASTENERS
E
H
F
Q
Visit the NEC Web Site at www.necsam.com
3 of 9
ISSUED: 04-11-06 SHEET #: 055-9458-2 05-09-06
For customer care call 1-800-729-0307 or 708-865-8870.
Page 4
Installation and assembly - Universal Adapter Plate
Note: The projector you are installing may differ in appearance from the sample illustrated below.
Place projector upside down. Locate adapter plate (L) with notch facing forward as close to projector center of
gravity as possible without covering any mounting holes. Loosen channels, and if there are only three mounting
holes remove fourth channel. Using one channel for each mounting hole, position feet of channels over mounting
holes as shown below. Important: If projector does not have at least three mounting holes, do not use this
adapter plate.
Note: Some projectors have feet which can be removed and the corresponding threaded insert can be used for a
mounting hole.
Note: Once channels are in position retighten fasteners.
*Notch indicates front of projector.
Mounting
hole
L
*
Generic Projector
Attach adapter plate (L) to projector using one screw (M, N, O, or P) for each channel as shown below. T ighten
all screws, while keeping the center of gravity . Be sure that adapter plate (L) is straight. Adjust the feet of the
channels to keep the adapter plate level. Tighten all screws with 4 mm security allen wrench (B) or wrench
provided with projector mount, while keeping the center of gravity . If M3 screws are used, tighten using 2 mm
security allen wrench (Q).
Note: Projectors will require different size screws for mounting. Use a combination of screws (M, N, O, or P) and
foot adjustment that will result in channels of adapter plate (L) fitting tightly against projector . Important: In order
to properly engage the threads in the mounting holes, the screw must be turned at least 3 full turns.
Note: If using screw (M), place washer (R) between screw (M) and foot of channel.
CAUTION
• It is the responsibility of the installer to ensure that the
projector is properly ventilated. Feet of channels are
used to raise the mount off the projector surface.
L
Generic Screw
Foot of Channel
Visit the NEC Web Site at www.necsam.com
4 of 9
ISSUED: 04-11-06 SHEET #: 055-9458-1
For customer care call 1-800-729-0307 or 708-865-8870.
Page 5
Installation To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings
Drill two 5/32" (4 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Attach ceiling plate (G)
with two #14 x 2.5" (6 mm x 65 mm) wood
screws (F) as shown using 3/8" (10 mm) socket
wrench.
Skip to step 2.
WOOD
JOIST
WARNING
• Tighten wood screws (F) so that wall plate (G) is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finder is highly recommended.
WARNING
• It is the responsibility of the installer to verify that the
supporting surface will safely support the combined
load of all attached hardware and components.
IMPORTANT: Be sure to drill holes into the
joist CENTER!
CEILING
G
F
F
WOOD
JOIST
CEILING
H
F
Visit the NEC Web Site at www.necsam.com
F
H
G
5 of 9
For optional Cord Management,
install two spacers (H) between ceiling
plate (G) and ceiling.
ISSUED: 04-11-06 SHEET #: 055-9458-2 05-09-06
For customer care call 1-800-729-0307 or 708-865-8870.
Page 6
WARNING
• When installing wall mounts on concrete, verify that you have a minimum of 1 5/8" of actual concrete surface in the 1/
4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Concrete must meet ASTM C-90
specifications.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor .
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum Load Capacity of 50 lb (22.7 kg).
Installation to Concrete Ceilings
ACC 203 (Alligator® concrete anchors) are recommended.
Drill two 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach ceiling plate (G) using two
concrete anchors and #14 x 2.5" wood screws (F) as
shown in Illustration A and 1, 2, and 3 (below).
Tighten all fasteners.
IMPORTANT: It is the responsibility of the installer
to verify that the ceiling will safely support the
combined load of all attached hardware and
components.
concrete
anchor
CONCRETE CEILING
WARNING
• Tighten wood screws so that wall plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finder is highly recommended.
1
Drill hole and insert anchor
2
G
F
Place ceiling plate over anchor and secure with screw
3
concrete
ceiling
concrete
anchor
concrete
anchor
G
F
Illustration A
WARNING
• FOR DIRECT AT TACHMENT T O LOAD BEARING
CONCRETE ONL Y! Concrete expansion anchors are
not intended for attachment to concrete ceilings
covered with a layer of plaster, drywall, or other
finishing material. If mounting to concrete ceiling
covered with plaster / drywall is unavoidable, plaster /
drywall must be counterbored as shown below.
metal
bracket
INCORRECT
concrete
metal
bracket
CORRECT
concrete
concrete
F
After repeating step one tighten all fasteners
Visit the NEC Web Site at www.necsam.com
anchor
6 of 9
CUT AW A Y VIEW
plaster/
dry wall
ISSUED: 04-11-06 SHEET #: 055-9458-1
For customer care call 1-800-729-0307 or 708-865-8870.
plaster/
dry wall
Page 7
Flush Mount Application
Screw ball and socket mount (A) into ceiling plate (G). Align the notch with one of the four holes of the ceiling plate
(G) and secure ball and socket mount (A) with a M5 x 10 mm socket pin screw (C) using security allen wrench (B)
as shown in detail 1.
Note: Slotted set screw (K) is used to jam against the threads of the ball and socket mount to prevent any excess
movement of the ball and socket mount (A). Do not overtighten screw; overtightening screw will damage threads
making it difficult to separate the products.
Skip to step 3.
K
NOTCH
CEILING
WOOD
G
A
C
A
G
DETAIL 1
Visit the NEC Web Site at www.necsam.com
7 of 9
ISSUED: 04-11-06 SHEET #: 055-9458-2 05-09-06
For customer care call 1-800-729-0307 or 708-865-8870.
Page 8
Installation to
Extension Column
G
C
K
Screw extension column to ceiling plate (G).
Align the notch with one of the four holes in
the ceiling plate (G) and secure extension
column with a M5 x 10 mm socket pin
screw (C) using security allen wrench (B).
See detail 4.
Screw extension column connector (I) to
extension column. Align slot in extension
column with one of the top holes in
extension column connector (I). Insert and
tighten one #10-32 x 3/8" socket pin screw
(J) through extension column connector (I)
into slot on extension column using security
allen wrench (B). See detail 5.
Screw ball and socket mount (A) to
extension column connector (I). Align slot in
ball and socket mount (A) to one of the
bottom holes in extension column connector
(I). Insert and tighten one #10-32 x 3/8"
socket pin screw (J) through extension
column connector into slot in ball and
socket mount (A) using security allen
wrench (B). See detail 6.
EXTENSION COLUMN
(UL Listed EXT or ADJ
Series)
Sold Separately
SLOT
I
SLOT
EXTENSION
COLUMN
K
I
G
EXTENSION
COLUMN
DETAIL 4
SLOT
J
Note: Slotted set screws (K) are used to
jam against the threads of each connecting
joint to prevent any excess movement. Do
not overtighten screws; overtightening
screws will damage threads making it
difficult to separate the products.
A
A
I
K
DETAIL 5
EXTENSION
COLUMN
SLOT
J
DETAIL 6
Visit the NEC Web Site at www.necsam.com
8 of 9
ISSUED: 04-11-06 SHEET #: 055-9458-1
For customer care call 1-800-729-0307 or 708-865-8870.
Page 9
Note: The projector adapter plate and projector you are installing may differ in appearance from the sample
illustrated below.
Attach projector, with adapter plate already on it, to the
ball and socket mount (A) by inserting the ball and
socket mount (A) into the adapter plate connection and
twisting until the adapter plate will no longer turn
(about 75°). The spring loaded captive screw should
line up with a corresponding hole on the adapter plate
(this should line up automatically when the two are
connected). Push down and tighten the spring loaded
captive screw to secure the adapter plate to the mount.
If not using the optional security feature, fasten thumb
screw (D) in the hole opposite the spring loaded
captive screw.
OPTIONAL: For security, insert serrated washer head
socket pin security screw (E) in the hole opposite the
spring loaded captive screw. Tighten with security
allen wrench (B). This will prevent the projector from
being removed.
Note: Be sure to only use the #10-32 x 3/8" screw (E)
(or the thumb screw (D)) opposite the spring loaded
captive screw.
CUTA W AY VIEW OF
CEILING PLATE ( G)
CEILING
E
WOOD
JOIST
D
To adjust roll, pitch, and yaw loosen the set screw
(shown below) using security allen wrench (B) or
standard 4 mm allen wrench. You should be able to
just slightly loosen the screw so that your adjustments
can be set without having to hold the projector. Move
projector to desired position and slowly tighten set
screw.
Note: Be sure not to touch the projector while
tightening the set screw. This may cause the image
to be unaligned when you let go.
IMPORTANT: Allen wrench is your key for projector
removal. Store it in a safe place.
WOOD
JOIST
CEILING
SET SCREW
A
CAPTIVE
SCREW
2
1
PROJECTOR ADAPTER PLA TE
PROJECTOR
WARNING
• Do not lift more weight than you can handle! Use
additional man power or mechanical lifting equipment
to safely handle placement of the projector!
PROJECTOR
Visit the NEC Web Site at www.necsam.com
9 of 9
ISSUED: 04-11-06 SHEET #: 055-9458-2 05-09-06
For customer care call 1-800-729-0307 or 708-865-8870.
Loading...