NEC NL10276AC28-01L Datasheet
DATA SHEET
NL10276AC28-01L
TFT COLOR LCD MODULE
36 cm (14.1 inches), 1024
××××
768 pixels, Full-color,
Multi-scan function, Built-in CRT interface board
DESCRIPTION
NL10276AC28-01L is a TFT (thin film transistor) active matrix color liquid crystal display (LCD) comprising
amorphous silicon TFT attached to each signal electrode, a driving circuit, a CRT interface board and a backlight.
NL10276AC28-01L has a built-in backlight with an inverter.
The 36 cm (14.1 inches) diagonal display area contains 1024 × 768 pixels and can display full-color (more than
16 million colors simultaneously). Also, it has wide viewing angle and multi-scan function.
FEATURES
• High Luminance (200 cd/m2. typ.)
• Low reflection
• CRT interface board
Auto recognition of input signal:
Analog RGB signals, Synchronous signals (Hsync,
Vsyn, Composite)
Digital control: e.g. Brightness, Display Position
Free supply voltage sequence
Corresponding to DDCI and DDC2B
Corresponding to VESA DPMS
• Multi-scan function: e.g. XGA, SVGA, VGA, VGATEXT, MAC
• Incorporated edge type backlight (Two lamps into
two lamp holders, Inverter)
• Lamp unit replaceable
(note)
VESA :
DPMS : Display Power Management Signaling
DDC1 : Display Data Channel 1
DDC2B: Display Data Channel 2B
Video Electronics Standards Associ ation
APPLICATIONS
• Desk-top type of PC
• Engineering workstation
• Display terminals for control system
• Monitors for process controller
On Screen Display
Application with the OSD function might conflict with patents in Europe and/or the U.S.A.
If you apply the OSD function, appreciate the patents at your side.
The information in this document is subject to change without notice.
Please confirm with the delivery specification before starting to design the system.
Document No. EN0444EJ1V0DS00 (1st edition)
Date Published May 2000 P
Printed in Japan
2000©
NL10276AC28-01L
STRUCTURE AND FUNCTIONS
A color TFT (thin film transistor) LCD module is comprised of a TFT liquid crystal panel structure, LSIs for driving
the TFT array, and a backlight assembly. The TFT panel structure is created by sandwiching liquid crystal material
in the narrow gap between a TFT array glass substrate and a color filter glass substrate. After the driver LSIs are
connected to the panel, the backlight assembly is attached to the backside of the panel.
RGB (red, green, blue) data signals from a source system is modulated into a form suitable for active matrix
addressing by the onboard signal processor and sent to the driver LSIs which in turn addresses the individual TFT
cells.
Acting as an electro-optical switch, each TFT cell regulates light transmission from the backlight assembly when
activated by the data source. By regulating the amount of light passing through the array of red, green, and blue
dots, color images are created with clarity.
OUTLINE OF CHARACTERISTICS (at room temperature)
Items Description
Display area 285.696 (H) × 214.272 (V) mm
Drive system a-Si TFT active matrix
Display colors Full-color
Number of pixels 1024 (H) × 768 (V)
Pixel arrangement RGB vertical stripe
Pixel pitch 0.279 (H) × 0.279 (V) mm
Module size 330.0 (H) × 255.0 (V) × 19.8 (D) mm (typ.)
Weight 1230 g (typ.)
Contrast ratio 150:1 (typ.)
Viewing angle (more than the
contrast ratio of 10:1)
Designed viewing direction • Opti m um graysc al e (γ = 2.2): perpendicular
Color gamut 40% (typ., At center, To NTSC)
Response time 11 ms (typ.), “white 100%” to “black 10%”
Luminance 200 cd/m2 (typ.)
Input signals Analog RGB signals, Synchronous signals (Hsync and Vsync or Composite)
Backlight Edge light type: two cold cathode fluorescent lamps with an invert er
Supply voltage 12 V, 12 V (Logic/LCD driving, Backlight)
Power consumption 16.0 W (typ.)
• Horizontal : 50° (typ., left side, right side)
• Vertical : 20° (typ., up side), 35° (typ., down side)
• Wider v i ewi n g angle wit h contrast rati o: down side ( 6 o’clock)
• Wider v i ewi n g angle wit hout image reversal: up side (12 o’clock)
Lamp holder: 141LHS08
Inverter: 141PW111
2
Data Sheet EN0444EJ1V0DS00
BLOCK DIAGRAM OF BASIC STRUCTURE
NL10276AC28-01L
I/F
HS/CS
Vsync
LEDON
LEDOFF
SEL
UP
DOWN
EXIT
LEFT
RIGHT
RESET
MENUSEL
V
(+12 V)
LCD module
R
G
B
Sync.
Signal
Signal
recognition
DD
CLK
PLL
OSD
Control
signal
Control
signal
Brightness control
Timing
Controller
ON/OFF
AIF
DC/DC
converter
AMP
V-driver
H-driver
3072 lines
LCD panel
768 lines
H: 1024 × 3 (R, G, B)
V: 768
V
DDB
(+12 V)
GNDB
GND
Inverter
Backlight
HS : Hsync
CS : Composite synchronous signal
: Neither GND nor GNDB is connected to frame. These should be connected in customers’
Note
equipment.
Data Sheet EN0444EJ1V0DS00
3
NL10276AC28-01L
GENERAL SPECIFICATIONS
Item Description Unit
Module size 330 ± 0.5 (H) × 255.0 ± 0.5 (V) × 20.5 (max.) (D) mm
Display area 285.696 (H) × 214.272 (V) mm
Number of dots 1024 × 3 (H) × 768 (V) dots
Pixel pitch 0.279 (H) × 0.279 (V) mm
Dot pitch 0.093 (H) × 0.279 (V) mm
Pixel arrangement RGB (Red, Green, Blue) vertical stripe –
Display colors Full color color
Weight 1,350 (max.) g
ABSOLUTE MAXIMUM RATINGS
Parameter Symbol Rating Unit Remarks
Logic input voltage V
R,G,B input voltage V
DD
V
DDB
V
In1
In2
–0.3 to + 14 VSupply voltage
–0.3 to + 14 V
–0.3 to + 5.5 V
–6.0 to + 6.0 V
a
T
= 25°C
a
T
= 25°C
DD
V
= 12 V
Storage temp. Tst –20 to + 60 °C –
%
3
Module surface
40 < Ta ≤ 50°C
Ta > 50°C
Operating temp. Top 0 to 50 °C
Relative Humidity
Absolute humidity Absolute humidity shall not exceed
: Measured at the LCD panel (Including self-fever)
Note
≤
95% Ta ≤ 40°C
≤
85%
a
= 50°C, RH = 85 %
T
g/m
Note
No condensation
4
Data Sheet EN0444EJ1V0DS00
ELECTRICAL CHARACTERISTICS
(1) Logic, LCD driving, Backlight
Item Symbol Min. Typ. Max. Unit Remarks
DD
V
DDB
V
Logic input “L” voltage V
Logic input “H” voltage V
Logic output “L” voltage V
Logic output “H” voltage V
Logic input “L” current I
Logic input “H” current I
Logic output “L” current 1 I
Logic output “H” current 1 I
Supply current
(Pixel checked pattern)
IL
IH
OL
OH
IL
IH
OL1
OH1
DD
DDB
I
NL10276AC28-01L
11.4 12.0 12.6 V Logic and LCD drivingSupply voltage
11.4 12.0 12.6 V Backlight
0–0.8V
2.2 – 5.25 V
––0.4V
2.4 – – V
–1 – –
––1
– – 100
–100 – –
µ
µ
µ
µ
– 630 900 mA VDD = 12.0 VI
– 170 200 mA Power saving mode
– 700 900 mA V
– 0.3 10 mA Power saving mode
HS/CS, Vsync, UP, DOWN, SEL,
RESET, EXIT, RIGHT, LEFT,
DDCCLK, DDCDAT
DDCDAT
HS/CS, Vsync
A
A
DDCDAT
A
A
DD
= 12.0 V
V
DDB
= 12.0 V
(Max. luminance)
DDB
= 12.0 V
V
a
= 25°C)
(T
(2) Video signal (R, G, B) input
Items Min. Typ. Max. Unit Remarks
Maximum amplitude (white - black) 0
(black)
DC input level (black)
Sync level
−
−
0.5 – +2.5 V –
0.2 0.3 *B
0.7
(white)
*A Vp-p
Vp-p G terminal
(0.6)
*A + *B – – 1.4 Vp-p –
: Contrast adjustment is needed if the amplitude exceeds 0.7 Vp-p.
Note
Note
(sync on green)
a
= 25°C)
(T
Data Sheet EN0444EJ1V0DS00
5
NL10276AC28-01L
Supply Voltage Sequence
(1) Please note that the supply voltage must not be applied to the module while the control signals (SEL, UP,
DOWN, EXIT, LEFT, RIGHT and RESET) are connected to GND. Otherwise the module may cause
malfunction.
(2) If the power supply voltage is applied while UP and DOWN are connected to GND, the input control signals
become an ineffective mode. To reset this mode, turn off the power once and turn on the power while UP
and DOWN are connected to GND. Then, the mode will be released.
(3) Do not change MENUSEL setting while the module is operated.
MENUSEL selection (Hierarchical type or Toggle type) is set when the power supply voltage is applied.
(4) Inverter current wave
Inverter current wave is as follows.
700 (mA)
0 (mA)
Duty
Luminance control frequency
maximum luminance control: 100 % (Duty)
minimam luminance control: 20 % (Duty)
Luminance control frequency Input Vsync frequency × K
=
Input Vsync frequency ≤ 75 Hz: K = 4.6
Input Vsync frequency > 75 Hz: K = 3.6
(5) Ripple of supply voltage
Please note that the ripple at the input connector of the module should be within the values shown in this
table. If the ripple is beyond these values, the noise may appear on the screen.
Supply voltage V
(for logic and LCD driver)
Acceptable range
: The acceptable range of ripple voltage includes spike noise.
Note
DD
≤
100 mVp-p
DDB
V
(for backlight)
≤
200 mVp-p
Example of the power supply connection
a) Separate the power supply b) Put the filter
Power V
Power V
DD
DDB
Power
Filter* V
Filter* V
DD
DDB
Filter* (reference value)
µ
L = 10
H to 100 µH
µ
C = 10
6
Data Sheet EN0444EJ1V0DS00
F to 100 µF
INTERFACE AND CONNECTOR PIN ASSIGNMENT
(1) Logic and LCD driving
CN1
Part No. : 1-353119-4
Adaptable socket: 1-353068-4
Supplier : Japan AMP Ltd.
NL10276AC28-01L
Pin No. Symbols Pin No. Symbols
1B8Vsync
2GND9GND
3G10HS/CS
4GND11GND
5 R 12 DDCCLK
6 GND 13 N. C.
7 GND 14 DDCDA T
Note 1:
N.C. (No connection) must be open.
CN3
Part No. : DF14A-25P-1.25H
Adaptable socket: DF14-25S-1.25C
Supplier : HIROSE ELECTRIC CO., LTD.
Pin No. Symbols Pin No. Symbols
1 LEDON 14 EXIT
2LEDOFF15 GND
3 GND 16 N. C.
4N.C.17GND
5N.C.18GND
6 RIGHT 19 MENUSE L
7LEFT20N.C.
8 RESET 21 N.C.
9 N.C. 22 N.C.
10 GND 23 GND
11 SEL 24 N.C.
12 UP 25 N.C.
13 DOWN
Figure from socket view
······1 2 13 14
Figure from socket view
···12 2524
Note 1:
N.C. (No connection) must be open.
Data Sheet EN0444EJ1V0DS00
7
CN5
Part No. : IL-Z-8PL-SMTY
Adaptable socket: IL-Z-8S-S125C3
Supplier : Japan Aviation Electronics Industry Limited (JAE)
NL10276AC28-01L
Pin No. Symbols Pin No. Symbols
1VDD5GND
2VDD6GND
3VDD7GND
4VDD8GND
(2) Backlight
CN201
Part No. : IL-Z-11PL1-SMTY
Adaptable socket: IL-Z-11S-S125C3
Supplier : Japan Aviation Electronics Industry Limited (JAE)
Pin No. Symbols Pin No. Symbols
1V
2V
3V
4 GNDB 10 N.C.
5 GNDB 11 N.C.
6 GNDB
DDB
DDB
DDB
7N.C.
8N.C.
9N.C.
Figure from socket view
·····87 21
Figure from socket view
···11 10 12
Note 1:
N.C. (No connection) must be open.
CN201
1
11
Rear view
1
14
1
25
8
1
CN1
CN3
CN5
8
Data Sheet EN0444EJ1V0DS00
NL10276AC28-01L
(3) PIN FUNCTION
Symbol I/O Logic Description
HS/CS Input Negative Horizontal synchronous signal input or composite synchronous signal input
(TTL level), Positive/Negative auto recognition
Vsync Input Negative Vertical synchronous signal i nput (TTL lev el)
Positive/Negative auto recognition, Cl ock i nput f o r DDC1
R Input – Red video signal input (0.7 Vp-p, input impedance 75 Ω)
G Input – Green v i deo signal input (0.7 Vp-p, input impedance 75 Ω)
B Input – Blue video signal input (0.7 Vp-p, input impedance 75 Ω)
LEDON Output Positive Indi cator for LED power on
“H”: LED select, “L”: Other status
LEDOFF Output Positive Indicator for power save mode
“H”: Power mode select, “L”: Other status
DDCCLK Input Positive CLK for DDC2B
DDCDAT Input/
Output
SEL Input Negative
UP Input Negat i ve Control si gnal (TTL level)
DOWN Input Negative Control signal (TTL level)
EXIT Input Negative Cont rol function exit signal (TTL level)
RIGHT
Note1
LEFT
Note1
RESET
Note1
MENUSEL Input – OSD design select signal (TTL level)
Input Negative Control signal (TTL level)
Input Negative Control signal (TTL level)
Input Negative Control signal (TTL level)
Positive Data for DDC1/ 2B
read/write
Control function select signal (TTL level)
SEL is pulled up in the module.
Detail of the functions are mentioned in Page 13
“H” or “open”: SEL off, “L”: SEL on
The signal increases the value of the functions selected.
UP is pulled up in tha module.
“H” or “open”: UP off, “L”: UP on
The signal decreases the value of the functions selected.
DOWN is pulled up in the module.
“H" or “open”: DOWN off, “L” : DOWN on
EXIT is pulled up in the module.
“H" or “open”: EXIT off, “L”: EXIT on
The signal increases the value of the functions selected.
RIGHT is pulled up in the module.
“H” or “open”: RIGHT off, “L”: RIGHT on
The signal decreases the value of the functions selected.
LEFT is pulled up in the module.
“H” or “open”: LEFT off, “L”: LEFT on
The signal initializes the selected function.
RESET is pulled up in the module.
“H” or “open”: RESET off, “L”: RESET on
MENUSEL is pulled up in the module.
“H or open”: Hierarchical type
“L”: Toggle type
For detail, see Page 10
OSD MENU SELECT
CONTROL FUNCTIONS
.
.
Data Sheet EN0444EJ1V0DS00
9
Symbol I/O Logic Description
DD
V
DDB
V
GND – – Ground for system
GNDB – – Ground for backlight
– – Power supply for Logic and LCD driving +12 V (±5%)
– – Power supply for backlight +12 V (±5%)
NL10276AC28-01L
Notes 1
: This terminal becomes effective only when the value of Button Sel is 7.
Detail of the functions is mentioned in Page 27
: Ground for system (GND) and backlight (GNDB) are not connected in the module.
2
: 12 V for backlight should be started up within 300 ms, othernise, the protection circuit makes the
3
INITIAL VALUE CHANGE FUNCTIONS
backlight turn off.
(4) OSD MENU SELECT
OSD menu type Hierarchical type Toggle type
MENUSEL “H” or “open” “L”
How to adjust
For details, see Page 27
CHANGE FUCNTIONS
INITIAL VALUE
.
For details, see Page 27
CHANGE FUCNTIONS
MENU
Auto Adjust
Brightness
Clock
Position
Contrast
.
INITIAL VALUE
.
Notes 1
: If OSD menu type is changed, the adjustment of the type becomes default value.
Then, It takes 5 seconds to display the changed menu after the supply voltage is input again.
And, Indicators for both LEDON and LEDOFF are “ON” at one time during the 5 seconds.
: The Initial value of Contrast ratio is as follows.
2
Hierarchical type: 128:1 (typ.)
Toggle type: 100:1 (typ.)
: On Screen Display
3
Application with the OSD function might conflict with patents in Europe and/or the U .S.A.
If you apply the OSD function, appreciate the patents at your side.
10
Data Sheet EN0444EJ1V0DS00
(5) Equivalent circuit
Symbol I/O Equivalent circuit
NL10276AC28-01L
LEDON
LEDOFF
Output RN2306 (Toshiba)
<Example of LED circuit>
Or equivalent
LCD module Output
R (330 Ω)
LEDON
LEDOFF
R (330 Ω)
SEL
UP
DOWN
EXIT
RIGHT
LEFT
RESET
Output
LED
SW
Data Sheet EN0444EJ1V0DS00
11
INPUT SIGNALS
(1) SYNCHRONOUS SIGNAL
This module is corresponding to the synchronous signals below.
NL10276AC28-01L
Auto recognition mode
Separate synchronous signal mode (HS, Vsync) Input Input Input or no input
Composite synchronous mode Input (cs) No input Input or no input
Sync. On Green mode No input No input Input
Power saving mode
Notes 1
: Power saving mode corresponds to VESA DPMA.
: The module recognizes Sync on Green signal automatically, when the FUNC in SOG Sel of Sel Data is
2
“Y”. Refer to Page 27
INITIAL VALUE CHANGE FUNCTION
HS/CS Vsync Sync. On Green
Input (HS) No input Input or No input
No input Input Input or no input
No Input No input No input
Synchronous signal
.
(2) PRESET TIMING
The 14 types of display timing shown below are preset in this module. The input synchronous signals are
automatically recognized.
Preset
No.
Display size
Vsync
(Hz)
Hsync
(kHz)
SYSTEM
CLK
(MHz)
V
Pulse
(H)
V
B.Porch
(H)
H
Pulse
(CLK)
H
B.Porch
(CLK)
Sync
Logic
V, H
Remarks
1 640 × 400 56.432 24.830 21.053 8 25 96 48 –,– *
2 640 × 480 59.992 31.469 25.175 2 33 96 48 –,– VGA
3 720 × 400 70.087 31.469 28.322 2 35 108 45 +,– VGA TXT
4 800 × 600 60.317 37.879 40.000 4 23 128 88 +,+ VESA
5 640 × 480 66.667 35.000 30.240 3 39 64 96 SonG Macintosh
6 640 × 480 75.000 37.500 31.500 3 16 64 120 –,– VESA
7 720 × 400 85.039 37.927 35.500 3 42 36 144 +,– VESA
8 640 × 480 85.008 43.269 36.000 3 25 48 112 –,– *
9 1024 × 768 60.004 48.363 65.000 6 29 136 160 –,– VESA
10 800 × 600 75.000 46.875 49.500 3 21 80 160 +,+ VESA
11 832 × 624 74.565 49.735 57.283 3 39 64 224 SonG Mac i ntos h
12 800 × 600 85.061 53.674 56.250 3 27 64 152 +,+ *
13 1024 × 768 70.069 56.476 75.000 6 29 136 144 +,+ VESA
14 1024 × 768 75.029 60.023 78.750 3 28 96 176 +,+ VESA
* Out of specification.
12
Data Sheet EN0444EJ1V0DS00
Loading...