NEC Express5800/B120e-h, N8400-217F, N8400-215F, N8400-216F, N8400-218F User Manual

...

Download

NEC Express Server

Express5800 Series

Express5800/B120e-h User’s Guide

Chapter 1 General Description Chapter 2 Preparations Chapter 3 Setup Chapter 4 Appendix

40.101.01-101.01

July 2013, First Edition

Model Number: N8400-215F/216F/217F/218F/219F/220F

Documents Provided with This Product

Express5800/B120e-h User's Guide

Documents Provided with This Product

Documents for this product are provided as accompanying booklets ( ) and as electronic manuals (

PDF

)

stored within the EXPRESSBUILDER DVD (

Precautions for Use

Describes points of caution to ensure the safe use of this server.

Read

these cautions before using this server.

Getting Started

Describes how to use this server, from unpacking to operations. Refer to this guide as you begin for an overview of this server.

User’s Guide

Chapter 1: General Description Overviews, names, and functions of the server’s parts

Chapter 2: Preparations Installation of additional options, connection of peripheral devices,

and ideal location for this server

Chapter 3: Setting Up Your Server System BIOS configurations and summary of EXPRESSBUILDER

PDF

Chapter 4: Appendix Specifications and other information

Installation Guide (Windows)

Chapter 1: Installing Windows Installation of Windows and drivers, and important information for

installation

PDF

Chapter 2: Installing the Bundled

Software

Installation of bundled software, such as NEC ESMPRO and Universal RAID Utility

Maintenance Guide

Chapter 1: Maintenance Server maintenance and troubleshootin g

Chapter 2: Convenient Features Useful features and the detail of system BIOS settings, RAID

Configuration Utility, and EXPRESSBUILDER

PDF

Chapter 3: Appendix Error messages and Windows Event Logs

Other documents

PDF

Provides the detail of NEC ESMPRO, Universal RAID Utility, and the other features.

EXPRESSBUILDER

Contents

Express5800/B120e-h User's Guide

Contents

Documents Provided with This Product.................................................................................................................2

Contents................................................................................................................................................................3

Notations Used in This Document.........................................................................................................................6

Notations used in the text....................................................................................................................6

Optical disk drives...............................................................................................................................6

Hard Disk Drives.................................................................................................................................6

Removable media...............................................................................................................................6

Abbreviations of Operating Systems (Windows).................................................................................7

Trademarks...........................................................................................................................................................8

Regulatory Notices................................................................................................................................................9

Warnings and Additions to This Document..........................................................................................................12

Latest editions...................................................................................................................................12

Precautions for Use (Be Sure to Read) ...................................................................................................13

Safety precautions............................................................................................................................13

Symbols used in this document and on warning labels.....................................................................14

Safety notes......................................................................................................................................15

Handling precautions (for proper operations)....................................................................................17

Handling precautions (for Anti-static Measures)................................................................................19

Handling precautions (Power-saving feature)...................................................................................20

Chapter 1 General Description ........................................................................................................................22

1. Introduction.....................................................................................................................................................23

2. Accessories ....................................................................................................................................................24

3. Standard Features..........................................................................................................................................25

3.1 Overview of Blade Server..........................................................................................................27

3.2 Management Features...............................................................................................................28

3.3 About the Monitoring of Chassis Sensors..................................................................................29

3.4 Firmware and Software Version Management...........................................................................29

4. Names and Features of Component...............................................................................................................30

4.1 CPU Blade.................................................................................................................................30

4.2 Solid State Drive (SSD)..............................................................................................................34

4.3 Lamp Indications........................................................................................................................35

4.3.1 POWER Lamp........................................................................................................35

4.3.2 STATUS Lamp........................................................................................................36

4.3.3 LAN (1 - 2) Link/Access Lamps..............................................................................37

4.3.4 ID Lamp..................................................................................................................37

4.3.5 SSD Access Lamp..................................................................................................37

Chapter 2 Preparations....................................................................................................................................38

1. Installing Internal Optional Devices ................................................................................................................39

1.1 Safety Precautions.....................................................................................................................39

1.2 Overview of Installation and Removal........................................................................................40

1.3 Installation and Removal Procedure (Common section)............................................................41

1.3.1 Removal of top cover..............................................................................................41

1.3.2 Removal of air duct.................................................................................................42

1.3.3 Installation of top cover and air duct.......................................................................44

Contents

Express5800/B120e-h User's Guide

1.4 Processor (CPU)........................................................................................................................45

1.4.1 Installation..............................................................................................................46

1.4.2 Removal.................................................................................................................50

1.5 DIMM.........................................................................................................................................51

1.5.1 Adding Order and Precautions................................................................................52

1.5.2 Installation..............................................................................................................52

1.5.3 Removal.................................................................................................................53

1.6 Mezzanine Card.........................................................................................................................54

1.6.1 Notes......................................................................................................................55

1.6.2 Installation..............................................................................................................55

1.6.3 Removal.................................................................................................................57

1.7 Solid State Drive (SSD)..............................................................................................................58

1.7.1 Installation..............................................................................................................59

1.7.2 Removal.................................................................................................................62

1.7.3 Replacement ..........................................................................................................63

1.7.4 Resetting Management Information........................................................................66

1.8 Use of Internal Hard Disk Drives in the RAID System ...............................................................67

1.8.1 Enabling a RAID System........................................................................................67

1.8.2 Notes on setting up a RAID System.......................................................................68

1.9 Trusted Platform Module Kit.......................................................................................................69

1.9.1 Installation..............................................................................................................70

1.9.2 Removal.................................................................................................................71

1.10 Internal Flash Memory.............................................................................................................72

1.10.1 Notes....................................................................................................................73

1.10.2 Installation.............................................................................................................73

1.10.3 Removal................................................................................................................74

2. Installation and Connection ............................................................................................................................75

2.1 Installation..................................................................................................................................75

2.1.1 Checking MAC Address..........................................................................................76

2.2 Connecting Peripheral Devices..................................................................................................78

2.2.1 USB Connection by K410-150(00) SUV Cable.......................................................81

2.2.2 Connecting with Network........................................................................................81

2.2.3 Connecting with UPS..............................................................................................82

Chapter 3 Setup...............................................................................................................................................83

1. Power-on of Blade Server ..............................................................................................................................84

1.1 Power ON from CPU Blade .......................................................................................................85

1.2 Power ON from Network Serial Port..........................................................................................86

1.3 Power ON from Remote Console ..............................................................................................86

1.4 Operation after Power ON .........................................................................................................86

1.5 POST.........................................................................................................................................87

1.5.1 POST Execution Flow ............................................................................................87

1.5.2 POST Error Messages ...........................................................................................89

2. BIOS Setup Utility (SETUP) ...........................................................................................................................90

2.1 Overview....................................................................................................................................90

2.2 Starting and Exiting SETUP Utility.............................................................................................90

2.3 Description on On-Screen Items and Key Usage ......................................................................91

2.4 Cases that Require Configuration..............................................................................................93

3. EXPRESSSCOPE ENGINE 3 ........................................................................................................................95

3.1 Overview....................................................................................................................................95

3.2 EXPRESSSCOPE ENGINE 3 Network Configuration ...............................................................96

4. EXPRESSBUILDER.......................................................................................................................................98

4.1 Features of EXPRESSBUILDER...............................................................................................98

4.2 Starting EXPRESSBUILDER.....................................................................................................98

5. Installing Software Components.....................................................................................................................99

5.1 Notes on using Red Hat Enterprise Linux 6...............................................................................99

5.1.1 About the message caused by power consumption control in

Red Hat Enterprise Linux 6.....................................................................................99

Contents

Express5800/B120e-h User's Guide

6. Device Identification .....................................................................................................................................101

7. Power-off of Blade Server.............................................................................................................................102

Chapter 4 Appendix.......................................................................................................................................103

1. Specifications ...............................................................................................................................................104

2. Interrupt Lines...............................................................................................................................................107

Notations Used in This Document

Express5800/B120e-h User's Guide

Notations Used in This Document

Notations used in the text

In addition to safety-related symbols urging caution, 3 other types of notations are used in this document. These notations have the following meanings.

Important

Indicates critical items that must be followed when handling the server or operating software. If the procedures described are not followed,

server failure, data loss, and other serious

malfunctions could occur

Note

Indicates items that must be confirmed when handling the server or operating software.

Tips

Indicates information that is helpful to keep in mind when using this server.

Optical disk drives

This server is equipped with one of the following drives, depending on the order at the time of purchase. These drives are referred to as optical disk drives in this document.

● DVD-ROM drive

● DVD Super MULTI drive

Hard Disk Drives

Unless otherwise stated, Hard Disk Drives (HDD) described in this document refer to the following.

● Hard disk drives (HDD)

● Solid state drive (SSD)

Removable media

Unless otherwise stated, removable media described in this document refer to the following.

● USB memory

● Flash FDD

Notations Used in This Document

Express5800/B120e-h User's Guide

Abbreviations of Operating Systems (Windows)

Windows Operating Systems are referred to as follows.

Refer to Chapter 1 (1.2 Supported Windows OS) in Installation Guide (Windows) for detailed information.

Notations in this document

Official names of Windows

Widnows Server 2012 Standard

Windows Server 2012

Widnows Server 2012 Datacenter

Windows Server 2008 R2 Standard

Windows Server 2008 R2

Windows Server 2008 R2 Enterprise Windows Server 2008 Standard

Windows Server 2008 *

Windows Server 2008 Enterprise

* Includes 64-bit and 32-bit Editions unless otherwise stated.

The following appears on EXPRESSBUILDER.

• Windows Server 2008 64-bit Edition: Windows Server 2008 x64

• Windows Server 2008 32-bit Edition: Windows Server 2008 x86

Trademarks

Express5800/B120e-h User's Guide

Trademarks

EXPRESSSCOPE is a registered trademark of NEC Corporation. Microsoft, Windows, Windows Server, and MS-DOS are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. Intel, Pentium, and Xeon are registered trademarks of Intel Corporation of the United States. AT is a registered trademark of International Business Machines Corporation of the United States and other countries. Adaptec, its logo, and SCSISelect are registered trademarks or trademarks of Adaptec, Inc. of the United States. LSI and the LSI logo design are trademarks or registered trademarks of LSI Corporation. Adobe, the Adobe logo, and Acrobat are trademarks of Adobe Systems Incorporated. DLT and DLTtape are trademarks of Quantum Corporation of the United States. PCI Express is a trademark of Peripheral Component Interconnect Special Interest Group.

Linux is a trademark or registered trademark of Linus Torvalds in Japan and other countries. Red Hat® and Red Hat Enterprise Linux are trademarks or registered trademarks of Red Hat, Inc. in the United States and other countries.

All other product, brand, or trade names used in this publication are the trademarks or registered trademarks of their respecti ve trademark owners.

Regulatory Notices

Express5800/B120e-h User's Guide

Regulatory Notices

FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Industry Canada Class A Emission Compliance Statement

This Class A digital apparatus complies with Canadian ICES-003.

Avis de conformité à la réglementation d'Industrie Canada

Cet appareil numérique de la classe A e st confo rme à la norme NMB-003 du Canada.

CE Statement

This is a Class A product. In domestic environment this product may cause radio interference in which case the user may be required to take adequate measures (EN55022).

BSMI Statement

WEEE

Disposing of your used product

In the European Union

EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes Information and Communication Technology (ICT) equipment or electrical accessories, such as cables or DVDs. When disposing of used products, you should comply with applicable legislation or agreements you may h ave. The mark on the electrical and electronic products only applies to the current European Union Member States.

Outside the European Union

If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority and ask for the correct method of disposal.

Regulatory Notices

Express5800/B120e-h User's Guide

Vietnam RoHS information relevant for Vietnam market

Declaration of Conformity

with the requirements of Technical Regulation on the Restriction Of the use of certain Hazardous

Substances in Electrical and Electronic Equipment

(adopted by Order №1057 of Cabinet of Ministers of Ukraine)

The Product is in conformity with the requirements of Technical Regulation on the Restriction Of the use of certain Hazardous Substances in electrical and electroni c equipment (TR on RoHS).

The content of hazardous substance with the exemption of the applications listed in the Annex №2 of TR on RoHS:

1. Lead (Pb) – not over 0,1wt % or 1000wt ppm;

2. Cadmium (Cd) – not over 0,01wt % or 100wt ppm;

3. Mercury (Hg) – not over 0,1wt % or 1000wt ppm;

4. Hexavalent chromium (Cr

) – not over 0,1wt % or 1000wt ppm;

5. Polybrominated biphenyls (PBBs) – not over 0,1wt % or 1000wt ppm;

6. Polybrominated diphenyl ethers (PBDEs) – not over 0,1wt % or 1000wt ppm.

Декларація про Відповідність

Вимогам Технічн ого Регламенту Обмеження Використання деяких Небезпечних Речовин в

електричному та електронному обладнанні

(затвердженого Постановою №1057 Кабінету Міністрів України)

Виріб відповідає вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та електронному обладнанні (ТР ОВНР).

Вміст небезпечних речовин у випадках, не обумовлених в Додатку №2 ТР ОВНР, :

1. свине

ць(Pb) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на

мільйон;

2. кадмій (Cd)– не перевищує 0,01 % ваги речовини або в концентрації до 100 частин на мільйон;

3. ртуть(Hg) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;

4. шестивалентний хром (Cr

) – не перевищує 0,1 % ваги речовини або в концентрації до

1000 частин на мільйон;

5. полібромбіфеноли (PBB) – не перевищує 0,1% ваги речовини або в концентрації до 1000 частин на мільйон;

6. полібромдефенілові ефіри (PBDE) – не перевищує 0,1 % ваги речовини або в

концентрації до 1000 частин на мільйон.

Декларация о Соответствии

Требованиям Техническ ого Регламента об Ограничении Использования некоторых Вредных

Веществ в электрическом и электронном оборудовании

(утверждённого Постановлением №1057 Кабинета Министров Украины)

Изделие соответствует требованиям Технического Регламента об Ограничении Использования некоторых Вредных Веществ в электрическом и электронном оборудовании (ТР ОИВВ).

Содержание вредных веществ в случаях, не предусмотренных Дополнением №2 ТР ОИВВ:

1. свине

ц (Pb) – не превышает 0,1 % веса вещества или в концентрации до 1000

миллионных частей;

2. кадмий (Cd) – не превышает 0,01 % веса вещества или в концентрации до 100 миллионных частей;

3. ртуть (Hg) – не превышает 0,1 % веса вещества или в концентрации до 1000 миллионных частей;

4. шестивалентный хром (Cr

)– не превышает 0,1 % веса вещества или в концентрации до

1000 миллионных частей;

5. полибромбифенолы (PBB) – не превышает 0,1 % веса вещества или в концентрации до 1000 миллионных частей;

6. полибромдифеноловые эфиры (PBDE) – не превышает 0,1 % веса вещества или в концентрации до 1000 миллионных частей.

Regulatory Notices

Express5800/B120e-h User's Guide

Turkish RoHS information relevant for Turkish market

EEE Yönetmeliğine Uygundur

Vietnam RoHS information relevant for Vietnam market

Complying with "CIRCULAR, No.30/2011/TT-BCT (Hanoi, August 10 2011), Temporary regulations on content limit for certain hazardous subst ances in electrical products”

Warnings and Additions to This Document

Express5800/B120e-h User's Guide

Warnings and Additions to This Document

● Unauthorized reproduction of the contents of this document, in part or in its entirety, is prohibited.

● The contents of this document may change without prior notice.

● Do not make copies or alter the document content without permission from NEC Corporation.

● Every effort has been made to ensure the completeness of this document. However, if you have any

concerns, or discover errors or omissions, please contact your retailer.

● Regardless of these Item 4, NEC Corporation does not take responsibility for effects resulting from operations.

● The sample values used in this document are not the actual values.

Keep this document nearby so that you may refer to it as necessary.

Latest editions

This document was created based on the information available at the time of its creation. T he screen images, messages and procedures may differ from the actual screens, messages and procedures.

Substitute as

appropriate when content has been modified. The most recent version of User’s Guide, as well as other related documents, is als o available for download

from the following website.

http://www.nec.co.jp/

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

Precautions for Use (Be Sure to Read)

The following provides information required to use your server safely and properly. For details of names in this section, refer to Names and Functions of Parts in this document.

Safety precautions

Follow the instructions in this document for the safe use of the NEC Express server. This User’s Guide describes hazardous parts of the server, possible hazards, and ho w to avoid them. Server

components with possible danger are indicated with a warning label placed on or around them (or, in some cases, by printing the warnings on the server).

In User’s Guide or on warning labels, WARNING or CAUTION is used to indicate a degree of danger. These terms are defined as follows:

WARNING

Indicates there is a risk of death or serious personal injury

CAUTION

Indicates there is a risk of burns, other personal injury, or property damage

Precautions and notices against hazards are presented with one of the foll owing three symbols. The individual symbols are defined as follows:

Attention This symbol indicates the presence of a hazard if

the instruction is ignored. An image in the symbol illustrates the hazard type.

Prohibited Action

This symbol indicates prohibited actions. An image in the symbol illustrates a particular prohibited action.

Mandatory Action

This symbol indicates mandatory actions. An image in the symbol illustrates a mandatory action to avoid a particular hazard.

(Electric shock risk)

(Example)

(Do not disassemble)

(Example)

(Disconnect a plug)

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

(A label example used in this User’s Guide)

Symbols used in this document and on warning labels

Attentions

Indicates the presence of electric shock hazards.

Indicates the presence of mechanical parts that can result in bodily injury.

Indicates the presence of a hot surface or component. Touching this surface could result in bodily injury.

Indicates the presence of mechanical parts that can result in pinching or other bodily injury.

Indicates there is a risk of explosion.

Indicates the presence of laser beam that cause blindness.

Indicates there is a risk of fire or fumes.

Indicates a general notice or warning that cannot be specifically identified.

Prohibited Actions

Do not disassemble, repair, or modify the server. Otherwise, an electric shock or fire may be caused.

Do not touch the server with wet hand. Otherwise, an electric shock may be caused.

Do not touch the component specified by this symbol. Otherwise, an electric shock or burn may be caused.

Do not use the server in the place where water or liquid may pour. Otherwise, an electric shock or fire may be caused.

Do not place the server near the fire. Otherwise, a fire may be caused.

Indicates a general prohibited action that cannot be specifically identified.

Mandatory Actions

Unplug the power cord of the server. Otherwise, an electric shock or fire may be caused.

Indicates a mandatory action that cannot be specifically identified. Make sure to follow the instruction.

Make sure equipment is properly grounded.

Otherwise, an electric shock or fire may be caused.

WARNING

Use only the specified outlet

Use a grounded outlet with the specified voltage. Use of an improper power source may cause a fire or a power leak.

Symbol to draw

attention

Description of a warning

Term indicating a degree of danger

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

Safety notes

This section provides notes on using the server safely. Re ad this section carefully to ensure proper and safe use of the server. For symbols, refer to Safety precautions.

WARNING

Do not use the server for services where human life may be at stake or high reliability is required.

This server is not intended for use in medical, nuclear, aerospace, mass transit or other applications where human life may be at stake or high reliability is required, nor is it intended for use in controlling such applications. We disclaim liability for any personal injury and property damages caused by such use of this server.

Do not disassemble, repair, or alter the server.

Never attempt to disassemble, repair, or alter the server on any occasion other than described in this User's Guide. Failure to follow this instruction may cause an electric shock or fire as well as malfunctions of the server.

Do not attempt to remove lithium, NiMH, or Li-ion batteries.

The server contains the lithium, NiMH, or Li-ion battery (some optional devices have a lithium, NiMH, or Li-ion battery installed). Do not remove the battery. Placing a battery close to a fire or in the water may cause an explosion.

When the server does not operate appropriately due to the dead battery, contact the store you purchased the product or your maintenance service company. Do not attempt to disassemble the server to replace or recharge the battery by yourself.

Do not use the server if any smoke, odor, or noise is present.

If smoke, odor, or noise is present, immediately turn off the power of all of the CPU blades, turn off the power of Blade Enclosure, then contact your sales representative. Using the server in such conditions may cause a fire.

Do not insert needles or metal objects.

Do not insert needles or metal objects into ventilation holes in the server or openings in the optical disk drive. Doing so may cause an electric shock.

Do not install devices in any other chassis than the specified Blade Enclosure.

Devices including CPU blades should be installed in the dedicated Blade Enclosure for their uses. Do not install the CPU blades and other devices in a chassis other than the Blade Enclosure. Failure to follow it may result in fire and/or electric shock to occur.

Do not use the server in an environment where corrosive gas is present

Do not install the server in a place subject to corrosive gases including sodium chloride, sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, or ozone. Do not install the server in an environment that contains dust, chemicals that accelerate corrosion such as NaCl or sulfur, or conductive materials. Failure to follow this warning may cause the wiring on the printed wiring board to short-circuit, leading to fire. If you have any questions, contact the store where you purchased the product or a maintenance service company.

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

WARNING

Do not handle the CPU blade if it is installed in the Blade Enclosure.

To install or remove an option from the CPU blade, first turn off the power of the C PU blade and remove the CPU blade from the Blade Enclosure. If you touch any components on the CPU blade with it connected to Blade Enclosure, you may get an electric shock.

Do not install or remove more than one CPU blade at a time.

Install or remove CPU blades one by one. If you install or remove more than one CPU blade at a time or a CPU blade with the cover of another slot removed, you may be electrically shocked.

CAUTION

Keep water or foreign matter away from the server.

Do not let any liquid such as water or foreign materials including pins or paper clips enter the server. Failure to follow this warning may cause an electric shock, a fire, or failure of the server. When such things accidentally enter the server, immediately turn off the power and disconnect the power plug from the outlet. Do not disassemble the server, and contact the store where you purchased the product or your maintenance service company.

Make sure to complete device installation.

Always install an interface cable, CPU blade, Solid State Drive, and option board firmly. An incompletely installed device may cause a contact failure, resulting in smoking or fire.

Use only the specified interface cable.

Use only interface cables authorized by NEC and locate a proper device and connector before connecting a cable. Using an unauthorized cable or connecting a cable to an improper destination may cause a short circuit, resulting in a fire. Also, observe the following notes on using and connecting an interface cable.

• Do not use any damaged cable connector.

• Do not step on the cable.

• Do not place any object on the cable.

• Do not use the server with loose cable connections.

• Do not use any damaged cable.

High temperature

Components including internal Solid State Drives in the server are extremely hot just after the server is turned off. Allow the surface to cool before installing/removing.

Avoid contact with the server during thunderstorms.

Do not touch any part of the server including the cables when a thunderstorm is approaching. Also, do not connect or disconnect any devices. There may be a risk of electric shock from lightning strike.

Keep animals away from the server.

Keep animals such as pets away from the server. Pet hair or other waste enters the server, which may cause a fire or electric shock.

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

Handling precautions (for proper operations)

Be sure to observe the following precautions for the proper functioning of the server. Ignoring the pr ecautions may cause server malfunction or failure.

● General

– Do not block air vents of the CPU blades, Blade Enclosures, power supply units, and additional FAN

units.

– The CPU blade and internal option devices contain precision component that is easily affected by

drastic temperature change. If the device is used after storage or relocation, make sure that the device is fully adapted to the operating environment.

– Do not touch the CPU blade terminals or on-board components by a bare hand nor place the CPU

blade directly on the desk.

– It is recommended to use options provided by NEC. Some memory devices and Solid State Drives of

other vendors are designed to be available for the server. If such an option causes the server to be defected or damaged, you will be charged for the repair within the warranty period.

– Turn off the device that generates magnetism or radio wave (e.g., the cellular phone or PHS around

the server. Radio interference may cause malfunctions of the server.

● CPU blade

– N8400-215F/216F/217F/218F/219F/220F CPU blade should be installe d in the Blade Enclosure

(SIGMABLADE).

– Install or remove CPU blades one by one. – Hold the portions covered with metal plates when a CPU blade is installed or removed. To carry a

CPU blade, put it into the case in which the CPU blade was contained at the purchase and pack it into the package.

– Check and adjust the system clock before the operation if any of the following conditions is

applicable.

 After transportation  After storage  After the server is used following a period of disuse, in which storage conditions did not conform to

those that guarantee server operations (temperature: 10°C to 35°C; humidity: 20% to 80%).

– Check the system clock at the rough rate of once per month. When the system clock is installed in a

system requiring high time precision, it is recommended to use a time server (NTP server). If the system clock is remarkably delayed or advanced as the passage of time in spite of adjustment, contact your sales representative to ask maintenance.

– Store the unit under the storage condition (temperature: –10°C to 55°C, humidity: 20% to 80%,

without condensation).

– After turning off the power of a CPU blade once, turn on the power again after 30 seconds (after the

POWER lamp of the CPU blade goes on amber) have passed from the power-off.

– Remove a CPU blade after turning off the power of the CPU blade.

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

– Do not perform any of the following operation during POST (including similar operations from EM

card and external applications).

 Press the POWER switch of the CPU blade.  Press the RESET switch of the CPU blade.  Remove the CPU blade from the Blade Enclosure.  Disconnect the power cord from the power unit of the Blade Enclosure.

● Solid state drive

– Confirm the slot to which the Solid State Drive is inserted. The slot for the Solid State Drive to be

connected to each CPU blade is defined previously.

Tips

Maintenance service We offer periodic diagnosis and maintenance services by staff with expert knowledge of the maintenance of this server. We recommend that you make a periodic maintenance service contract with your maintenance service company to keep your server in good condition.

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

Handling precautions (for Anti-static Measures)

This product contains static-sensitive electronic components. Follow this measures below to avoid a failure caused by static electricity when installing or uninstalling any optional device.

● Wearing Anti-static Wrist Strap Or Anti-static Gloves

Wear a wrist strap on your wrist and connect the wire to the chassis. If there is no wrist strap, touch an unpainted metal surface of the chassis connected to the ground to discharge static e lectricity from your body before touching the component. Touch the metal part occasionally to discharge the static electricity while working on the component.

● Checking the Workplace

– Work on an anti-static floor or concrete floor. – If you work on a place where static electricity is likely to be generated (e.g. carpet), be sure to

provide anti-static protection.

● Using the Work Table

Place the server on a mat with Electrostatic Discharge (ESD) protection.

● Clothing

– Do not wear wool or synthetic clothes. – Wear anti-static shoes. – Remove any kind of metal accessories such as a ring, bracelet or wrist watch.

● Handling of Components

– Keep the component in an anti-static bag until you install it to the server. – Hold the component by the edges to avoid touching any terminals or mounting parts. – Place the component in an anti-static bag when storing or moving them.

● Handling of Cables

When connecting a cable (e.g., LAN cable), static electricity may also be charged due to friction against the floor. Connecting the charged cable with an I/O device may cause damage to the devices in the system. It is recommended to use a product such as electrostatic discharge kit to eliminate th e static charge before connecting the cable.

● Installing and Uninstalling the Optional Device

– To avoid electric hazard and malfunction, be sure to turn off the power switch of the server and

unplug the power cord from the outlet before installing or uninstalling any optional dev ice. If the device is hot-swappable, you do not need to turn off the power switch and unplug the power cord.

– The device contains static-sensitive electronic components. When installing or uninstalling the

optional device, wear an anti-static wrist strap on your wrist to avoid a failure caused by the static electricity. To use the strap, connect the wire to the chassis.

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

Handling precautions

(Power-saving feature)

The server does not support power-saving features of OS such as Standby, Hibernate, and Sleep mode.

Precautions for Use (Be Sure to Read)

Express5800/B120e-h User's Guide

Using a computer extensively may affect different parts of your body. Here are tips you should follow while working on a computer to minimize strain on your body.

Keep proper posture

The basic body position for using a computer is sitting straight with your hands on the keyboard parallel with the floor, and your eyes directed slightly downward toward the monitor. With the proper posture described above, no unnecessary strain is applied on any part of your body, in other words when your muscles are most relaxed.

Working on the computer with bad posture such as hunching over or being too close to the monitor could cause fatigue or deteriorated eyesight.

Adjust the angle of your display

Most display units are designed for adjustment of the horizontal and vertical angles. This adjustment is important to prevent the screen from reflecting bright lights and to make the display contents easy to see. Working without adjusting the display to a comfortable angle makes it difficult for you to maintain a proper posture and you will get tired easily. Adjust the viewing angle before use.

Adjust the brightness and contrast of the display

Display screens have functions to control brightness and contrast. The most suitable brightness/contrast depends on age, individuals, and environment, so adjust it to suit your preferences. A too bright or too dark display is bad for your eyes.

Adjust the angle of keyboard

Some keyboards are ergonomically designed, which allow the angle to be adjusted. Adjusting the angle of the keyboard is effective to reduce tension on your shoulders, arms, and fingers.

Clean your equipment

Keeping your equipment clean is important not only for the appearance but also for functional and safety reasons. A dusty monitor makes it difficult to see the display contents, so clean it regularly.

Take rest breaks

When you feel tired, take a break. Light exercise is also recommended.

Tips for your health and safety

Express5800/B120e-h User's Guide

NEC Express5800 Series Express5800/B120e-h

General Description

This chapter describes the features of the server and bundled software, and precautions on installation.

1. Introduction

2. Accessories Verify the condition of your server's accessories.

3. Standard Features

Describes standard features of the server and system management utilities.

4. Names and Functions of Parts

This section describes the name of each part contained in this server.

1. Introduction

Express5800/B120e-h User's Guide

Chapter 1 General Description

Introduction

Welcome to the NEC Express5800/BladeServer series server. This high performance and high density server is powered by the latest microprocessor "Intel

Xeon®

processor. NEC’s latest technology and architectures realize more space-saving and reduction of running cost than ever. The server is designed with consideration of not only reliability but also expandability, which enables you to use

it as a network server. Read this document before using the server thoroughly to fully understand h andling of Express5800 Series

Server and appreciate its functions to the maximum extent.

2. Accessories

Express5800/B120e-h User's Guide

Chapter 1 General Description

Accessories

The carton box contains various accessories which are required for setup or maintenance. Make sure you have them all for future use.

• EXPRESSBUILDER

• Getting Started

*1 Documents are stored in EXPRESSBUILDER. Adobe Reader is required to read the documents so make

sure you have it installed in your PC.

Make sure you have all accessories and inspect them. If an accessory is missing or damaged, contact your sales representative.

Important The chassis serial number plate and maintenance label is located on the

server. If the serial number does not match the number on the w arranty, you may not be guaranteed against failure even within the warranty period. Contact your sales representative if they do not match.

3. Standard Features

Express5800/B120e-h User's Guide

Chapter 1 General Description

Standard Features

The server has the following standard features:

High performance

• Intel® Xeon® E5 processor

• DDR3-1333/1600 Registered DIMM and DDR3-1600 Unbuffered DIMM

• High-speed 10GBASE-KR interface (10Gbps supported), 2 ports

• High-speed disk access

High reliability

• Memory monitoring feature (correction of correctable error/detection of uncorrectable error (when registered DIMM is used))

• Forced start-up with failed memory

• Bus parity error detection

• Temperature detection

• Error detection

• Internal voltage monitoring feature

• BIOS password feature

Management Utilities

• NEC ESMPRO

• Remote controlling featuer (EXPRESSSCOPE Engine 3)

• ExpressUpdate

• RAID System management utility (Universal RAID Utility)

Expandability

• Slot for Mezzanine card

• Large capacity memory of up to 512 GB

• Can upgrade to multi-processor system with up to two processors

• Two network ports

• Up to two Solid State Drives (2.5-inch) per a CPU blade can be connected

• USB2.0 interface (2 ports)

3. Standard Features

Express5800/B120e-h User's Guide

Chapter 1 General Description

Many built-in Features

• Software power-off

• Remote power-on feature

• AC-Link feature

Self-diagnosis

• Power On Self-Test (POST)

• Test and Diagnosis (T&D) utility

Easy setup

• EXPRESSBUILDER (setup utility)

• SETUP (BIOS SETUP utility)

Maintenance features

• Off-line Tools

• Memory dump feature using the DUMP switch

3. Standard Features

Express5800/B120e-h User's Guide

Chapter 1 General Description

3.1

Overview of Blade Server

In the Internet society diversified increasingly, every s ystem administrator should hav e a request of "run many servers in less installation spaces".

If a server has only one server function, installation space increases at eve r y extension ev en if th e chassi s size is minimized. In addition, an unexpected expenses, such as construction of a p ower supply and the purchase of the rack for storage, may occur.

With "Express5800/BladeSever Series", the server function is narrowed to necessity minimum and condensed on one board (CPU Blade) to realize space-saving and and intensive server .

The CPU Blade does not require any wiring or connection of a power supply and a cable. Moreover, a processor, a memory, a solid state drive, a mezzanine card, and others can be installed as an

option in the CPU Blade that has a server function.

Save space

and

save power

Blade Enclosure

CPU blade

Increase

in installation space

Increase in

consumption

power

3. Standard Features

Express5800/B120e-h User's Guide

Chapter 1 General Description

3.2

Management Features

The hardware components of the server provide operation control/reliability features as shown below. Additionally, NEC ESMPRO Agent, which is provided in EXPRESSBUILDER, enables you to collectively manage the state of your systems. You can also monitor the server states from a PC to manage the network where NEC ESMPRO Manager provided in EXPRESSBUILDER is installed.

The features available on this server are as shown in the table below.

Function Availability Description

Shows physical hardware information.

Memory bank

{

Shows physical memory information.

Device info

{

Shows information specific to the server.

Hardware

CPU

{

Shows physical CPU information.

System

{

Shows logical CPU information and monitors the load factor. Shows logical memory information and monitors the status.

I/O device

{

Shows information on I/O devices (floppy disk drive, serial ports, parallel port, keyboard, mouse, and video).

Monitors temperatures, fans, voltage, power supply, door, and

others.

Temperature

{

Monitors the temperature inside of the chassis.

Fan

Monitors the fans.

Voltage

{

Monitors the voltage inside of the chassis.

Power supply

Monitors the power supply unit.

System environment

Door

Monitors Chassis Intrusion (open/close state of chassis cover or door).

Software

{

Shows service, driver, and OS information.

Network

{

Shows network (LAN) information and monitors packets.

BIOS

{

Shows BIOS information.

Local polling

{

Monitors the values of MIB items obtained by NEC ESMPRO Agent.

Storage

{

Monitors controllers and storage devices including Solid State Drives.

File system

{

Shows the file system configuration and monitors the free space.

RAID System / Disk Array

{

Monitors the following RAID Controller:

N8404-003F Storage and I/O Blade AD106b

{

Monitors OS stall using the Watch Dog Timer.

Others*

{

Performs alert processing after an OS STOP error occurs.

{: Supported. U: Partially supported. ×: Unsupported. *: Not displayed on the NEC ESMPRO Manager screen.

Tips

NEC ESMPRO Manager and NEC ESMPRO Agent are supplied with the server as standard. For how to install and use each software component, refer to the explanation of the component.

3. Standard Features

Express5800/B120e-h User's Guide

Chapter 1 General Description

3.3

About the Monitoring of Chassis Sensors

The fan and the power supply units installed in Blade Enclosure (SIGMABLADE) are monitored b y the EM card. The information that the EM card monitors can be confirmed by the Information of EM Card state/constitution of NEC ESMPRO Manager.

In Enclosure → Power Supply tree in the Information of server state/constitution of NEC ESMPRO Manager, the status of the power circuit of CPU blade is displayed.

3.4

Firmware and Software Version Management

Use of NEC ESMPRO Manager and ExpressUpdate Agent allows you to manage versions of firmware and software as well as update them by applying update packages.

This function automatically updates multiple modules without stopping the system just by specifying the application of an update package from NEC ESMPRO Manager.

4. Names and Features of Component

Express5800/B120e-h User's Guide

Chapter 1 General Description

Names and Features of Component

This section describes the names and features of the components in the device.

4.1

CPU Blade

This section describes the names, installation positions, and features of the sections on the CPU blade.

CPU blade

(1) DIMM socket (CPU#2)

CPU2_DIMM3, CPU2_DIMM7, CPU2_DIMM4, CPU2_DIMM8 from top

(2) DIMM socket (CPU#2)

CPU2_DIMM6, CPU2_DIMM2, CPU2_DIMM5, CPU2_DIMM1 from top

(3) DIMM socket (CPU#1)

CPU1_DIMM1, CPU1_DIMM5, CPU1_DIMM2, CPU1_DIMM6 from top

(4) DIMM socket (CPU#1)

CPU1_DIMM8, CPU1_DIMM4, CPU1_DIMM7, CPU1_DIMM3 from top

(5) SSD cable connector

Connector to connect a cable for Solid State Drive that is mounted on air duct.

(6) SSD1 cable connector

Connector to connect a cable for Solid State Drive #0 that is mounted on air duct.

(7) SSD2 cable connector

Connector to connect a cable for Solid State Drive #1 that is mounted on air duct.

(8) Mezzanine card slot (Type 2)

Slot to install mezzanine card for blade. The slot number is "MEZ2".

(9) Mezzanine card slot (Type 1)

Slot to install mezzanine card for blade. The slot number is "MEZ1".

(10) Connector for Internal Flash Memory

Connector to install Internal Flash Memory.

(11) Connector for Trusted Platform Module Kit

Connector to install Trusted Platform Module Kit .

(12) Connector for LAN riser card

Connector to install LAN riser card.

(13) Socket for processor #1 (CPU #1)

Socket tor optional processor #1 (CPU #1) (CPU#2 and CPU heat sink are installed.)

(14) Socket for processor #2 (CPU #2)

Socket tor optional processor #2 (CPU #2) (CPU#2 and CPU heat sink are not installed.)

(15) SUV cable connector (16) Eject lever

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(12)

(11)

(13)

(14)

(15)

(16)

4. Names and Features of Component

Express5800/B120e-h User's Guide

Chapter 1 General Description

CPU Blade Access Side

DMP

RST

(1) POWER lamp

The lamp goes on green when the CPU blade is powered on. The lamp goes on amber when the CPU blade is powered off but the power is supplied from the power supply unit.

(2) POWER switch

The switch is intended to turn on or off the powe

of the CPU blade itself. Pressing the switch for 4 seconds or longer causes the power supply to be turned off forcibly.

(3) STATUS lamp (green/amber/red)

The lamp indicates the status of the CPU blade. See "Lamp Indications" described later for the indications and meanings of the lamp.

(4) DUMP switch

Press this switch to run the memory dump.

(5) LAN1 Link/Access lamp (green)

The lamp goes on when LAN port 1 is connected to the network. The lamp blinks when data is being transmitted.

(6) RESET switch

Press this switch to reset the CPU blade.

(7) LAN2 Link/Access lamp (green)

The lamp lights when LAN port 2 is connected to the network. The lamp blinks when data is being transmitted.

(8) ID/BMC RESET switch

Press this switch to turn on or off the ID lamp. Pressing this switch toggles lamp ON/OFF. Refer to Chapter 1 (7.2 BMC Reset) in Maintenance Guide for BMC RESET switch.

(9) ID lamp

The lamp is intended to identify the CPU blade in the system. The lamp is lit by a switch or software command. When the recognize command is received from NEC ESMPRO Manager and when the ID switch is pressed, the lamp goes on. You may use the remote control feature o

EXPRESSSCOPE Engine 3 (BMC) to perform the same operation as using the ID switch on the server.

(10) Eject lever

Pull the lever to remove the CPU blade from the Blade Enclosure.

(11) SUV cable connector

This connector sends or receives various signals. The K410-150(00) SUV cable (separately-priced o

provided with the SIGMABLADE) is connected to this connector.

(12) SSD Access lamp

If the server is equipped with optional Solid State Drives, the lamp goes on while optional Solid State Drive is being accessded. (upper: #0 / lower: #1)

(13) Slide tag

A label on which the model number and serial number are described is attached this slide tag. You can check the label contents by pulling this slide tag.

DMP

RST

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(10)

(13)

(12)

4. Names and Features of Component

Express5800/B120e-h User's Guide

Chapter 1 General Description

External View

With top cover installed

(1) Top cover

(2) Front frame

With top cover removed

(1) SSD cable

(2) SSD bay 0

(3) SSD bay 1

(4) Air duct

(1)

(2)

(4)

(1)

(3)

(2)

4. Names and Features of Component

Express5800/B120e-h User's Guide

Chapter 1 General Description

With top cover, air duct, and front frame removed

(1) DIMM

(1)

4. Names and Features of Component

Express5800/B120e-h User's Guide

Chapter 1 General Description

4.2

Solid State Drive (SSD)

The Solid State Drive is an optional device . An operating system may be installed in the Solid State Drive. Handle it carefully.

(1) Solid state drive (2) SATA connector

Connect SSD cable to this connector.

(3) Screws (2) (4) SSD mount bracket

Provided with screws.

(1)

(2)

(4)

(3)

4. Names and Features of Component

Express5800/B120e-h User's Guide

Chapter 1 General Description

4.3

Lamp Indications

This section describes the positions and display meanings of the lamps on the CPU blade and oth er devices.

CPU Blade

The CPU blade has 7 lamps.

DMP

RST

4.3.1

POWER Lamp

The POWER lamp lights green while the power of the CPU blade is on. The lamp light s amber when the CPU blade is powered off but the power is supplied from the power supply unit. The lamp is off if the power is not supplied to the system.

SSD Access lamp (#0)

POWER lamp

STATUS lamp

ID lamp

LAN2 Link/Access lamp

LAN1 Link/Access lamp

SSD Access lamp (#1)

4. Names and Features of Component

Express5800/B120e-h User's Guide

Chapter 1 General Description

4.3.2

STATUS Lamp

The STATUS lamp stays lit in green when the CPU blade is in successful operation. When the STAT US lamp is flashing in amber or red, it indicates that the system has failed. In addition, you can view the detailed information on error message on virtual LCD when the STATUS lamp is flashing in amber or red. You can use the virtual LCD through the Web browser of EXPRESSSCOPE Engine 3 (BMC) or NEC ESMPRO Manager.

The following table lists indications of the STATUS lamp and virtual LCD, descriptions, and actions to take. If an error occurs, contact your sales representative.

Tips If the CPU blade has the NEC ESMPRO installed, you can view the error log to identify

the cause of a trouble.

Status of

STATUS lamp

Color Description Action

On Green The CPU blade is operating normally. – Off – The power is turned off. Turn on the power. On Red BMC is being initialized. 1. Wait until the lamp goes off.

2. If the lamp still goes on, check installation status of the CPU blade.

BMC does not work normally due to incorrect installation of LAN riser card.

If the indication of ID lamp does not change even when the ID switch is pressed, contact your sales representative. The virtual LCD indication cannot be obtained because BMC is not working.

Flash Red

An error occurred. Identify the error cause according to Chapter 3 (1. POST Error Message) in Maintenance Guide.

Flash Amber A warning level error occurred. Identify the error cause according to Chapter 3 (1.

POST Error Message) in Maintenance Guide.

Tips

If the CPU blade is powered off while the STATUS lamp is flashing in amber or red, the indication of the STATUS lamp is retained except for certain factors. When the CPU blade is powered on, the STATUS lamp goes on green (normal status).

4. Names and Features of Component

Express5800/B120e-h User's Guide

Chapter 1 General Description

4.3.3

LAN (1 - 2) Link/Access Lamps

The lamp blinks when data is being transmitted through the LAN port. When the CPU blade is powered on and the LAN cable is connected, the lamp on LAN port for which the link is being established goes on. The connection of LAN port is physically controlled by the EM card and the switch module installed in the Blade Enclosure.

To check connection status of LAN port, refer to the User's Guides of the EM card and the switch module installed in the Blade Enclosure.

4.3.4

ID Lamp

Pressing the ID switch brings the lamp to light, and pressing again brings the lamp to go off. The ID lamp is intended to identify a specific CPU blade in the rack in which more than one CPU blade is installed. Making this lamp being lit can help the maintenance work to identify the faulty device.

If you press the ID switch, the lamp goes on. When the recognize command is receiv ed from management software such as NEC ESMPRO Manager, the lamp also goes on.

You may use the remote control feature of EXPRESSSCOPE Engine 3 (BMC) to perform the same operation as using the ID switch on the server.

4.3.5

SSD Access Lamp

The lamp lights while accessing to a Solid State Drive occurs (however, if the Solid State Drives are operated in the RAID System, the lamp operates only in the OS boot status).

The lamp is lit amber if a Solid State Drive cannot be interfaced with the CPU blade correctly due to a hardware fault in the CPU blade or another failure.

In the RAID System, the lamp blinks green or amber alternately while the Logical Drives are rebuilt (this does not indicate an error). After the rebuilding completes, the lamp returns to the normal indication. If the rebuilding fails, the lamp is lit amber.

Express5800/B120e-h User's Guide

NEC Express5800 Series Express5800/B120e-h

Preparations

This chapter describes preparations for using this server.

1. Installing Internal Optional Devices

You can skip this section if you did not purchase any optional devices.

2. Ideal Location and Connection

You must place the server in an ideal location and connect cables following this section.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

Installing Internal Optional Devices

This section describes the instructions for installing supported optional devices and precautions. If you did not purchase any optional device requiring installation, you may skip this section.

Important • We recommend that optional devices be installed by a maintenance service

staff from your maintenance service company, who has specialized know ledge of this server.

• Use only the devices and cables specified by NEC. You will be charged to

repair damages, malfunctions, and failures caused by the use of any devices or cables not specified for use with this server even within the warranty period.

• When you made any change to the hardware configuration, make sure to

update the system (Refer to the Installation Guide for details.).

1.1

Safety Precautions

Be sure to observe the following precautions to install and remove optional devices properly and safely.

WARNING

Be sure to observe the following precautions to use the server safety. Failur e to observe the precautions may cause death or serious injury. For details, refer to Safety precautions in Precautions for Use.

• Do not disassemble, repair, or modify the server.

• Do not remove the lithium battery, NiMH battery, or Li-ion battery.

• Disconnect the power plug when installing and removing devices.

CAUTION

Be sure to observe the following precautions to use the server safely. Failure to observe the precautions may cause burns, injury, and property damage. For details, refer to Safety precautions in Precautions for Use.

• Pay attention to hot surface.

• Make sure to complete installation.

• Do not install with the top cover, air duct, and/or front frame removed.

• Do not get your fingers caught.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.2

Overview of Installation and Removal

To install or remove an optional device or Solid State Drive installed in the CPU blade, you should first remove the CPU blade from the Blade Enclosure. Refer to Chapter 2 (2. Installation and Connection) for details.

Important Remove the target CPU blade only. Do not remo ve any other blank cover or CPU

blade from another slot. Be sure to install or remove the CPU blade one by one.

CAUTION

• Pay attention to hot surface.

• Make sure to complete installation.

• Do not install with the top cover, air duct, and/or front frame removed.

• Do not get your fingers caught when installing components

1. After the shutdown processing for the CPU blade to be removed, turn off the power of the CPU blade. Refer to Chapter 3 (7. Power-off of Blade Server).

2. Take the CPU blade out from the Blade Enclosure. Refer to the User's Guide of the Blade Enclosure.

3. Put the CPU blade on an anti-static sheet with little dust.

4. Remove the top cover. In addition, remove the air duct if needed. Refer to Chapter 2 (1.3 Installation and Removal Procedure (Common section)).

5. Perform installation or removal procedure for the component required for your system. Refer to sections in Chapter 2 (1.4 Processor (CPU) through 1.10 Internal Flash Memory).

6. Install the top cover. In addition, install the air duct if needed. Refer to Chapter 2 (1.3 Installation and Removal Procedure (Common section)).

7. Install the CPU blade in Blade Enclosure. Refer to the User's Guide of Blade Enclosure.

This completes installation or removal of internal optional devices. Continue the setup with reference to Chapter 2 (2.2 Connecting Peripheral Devices).

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.3

Installation and Removal Procedure (Common section)

Take steps below to install or remove top cover and air duct.

1.3.1

Removal of top cover

Take steps below to remove the top cover.

1. After the shutdown processing for the CPU blade to be removed, turn off the power of the CPU blade.

2. Take the CPU blade out from the Blade Enclosure. Refer to the User's Guide of the Blade Enclosure.

3. Put the CPU blade on an anti-static sheet with little dust.

4. Remove the two screws that secure the top cover.

5. Firmly hold the top cover, move it slightly toward the rear of the CPU blade, then lift the cover to remove it from the CPU blade.

Important Pay attention not to make the cover hit any electronic component on the CPU blade.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.3.2

Removal of air duct

Take steps below to remove air duct.

1. Remove the two screws from the front frame that secures the air duct.

2. Pull the front frame toward the front of CPU blade, and remove it.

3. Remove the three SSD cable conn ectors. This step is not required if the N8403-042F diskless kit has been installed. Proceed to Step 4.

Important Pay attention to orientation of guide key on SSD cable connector.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

4. Remove the two screws securing the air duct.

5. Firmly hold the air duct, and lift it to remove.

Important • Pay attention not to make the air duct hit any electronic component on t he C PU

blade.

• Pay attention not to damage the SSD cable.

• If SSD is installed on air duct, carefully handle the air duct not to give any

shock to SSD.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.3.3

Installation of top cover and air duct

To install top cover and air duct, perform installation steps (Chapter 2 (1.3.1 Removal of top cover) and (1.3.2 Removal of air duct)) in reverse order.

Note the following when installing these components.

● Installing removed components exactly as they were Install the components and cables, which were removed and disconnected for addition of an option, exactly as they were. Assembling without a component being installed or a cable being disconnected causes the server to malfunction.

● Confirming that no parts such as screws are left in the server Confirm that particularly conductive parts such as screws are not left in the server. Turning on the power with a conductive part on the mother board or cable terminal causes the server to malfunction.

● Confirming the cooling effect in the server Confirm that the ventilating holes are not covered with an internally connected cable. Insufficient cooling effect raises the internal temperature, which causes the server to malfunction.

● Confirming operation with a tool Some additional devices require the diagnostic utility or BIOS SETUP utilit y to check if they are installed correctly. For details, see the procedure for installing the target device.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.4

Processor (CPU)

The server may have another CPU installed in addition to the factory-installed CPU (Intel® Xeon® Processor).

Important • The CPU to be added must have the same specification (the core voltage,

clock, and others) as the CPU already installed.

• The CPU is extremely sensitive to static electricity. Make sure to touch the

metal frame of the server to discharge static electricity from your body befor e handling the CPU. Do not touch the CPU pins b y a bare hand or place the CPU directly on the desk. For static notes, refer to “Handling precautions (for Anti-static Measures)”.

• Do not operate the system until confirming that the additionally ins talled CPU

is in normal state.

• Make sure to use the CPU authorized by NEC. Installing a third-party CPU may

cause a failure of the CPU as well as the server. Repair o f the server due to failures or damage resulted from installing such a CPU will be charge d.

Tips

An optional CPU of different revision may be contained in the system. If the CPU of different revision is installed, Windows 2003 logs the following information in system log of Event Viewer. However, this event does not affect the system operation.

CPU #1 (to be installed below the heat sink)

CPU #2 (to be installed below the socket cover)

CPU blade

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.4.1

Installation

Install the CPU in the following procedure.

1. Remove the top cover and air duct according to Chapter 2 (1.3.1 Removal of top cover) and (1.3.2 Removal

of air duct).

2. Confirm the position of the CPU socket.

3. Push down the socket lever once to unlatch it from the hook, then slowly open the lever until it stops.

4. Lift the CPU socket holder.

Important You will see the CPU socket contacts. Do not touch the socket contacts.

5. Remove the socket cover.

Important Keep the removed socket cover for future use. Alw ays attach the socke t co ver if the

processor is removed from the socket.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

6. Put the additional processor on the CPU socket slowly and gently.

For easy installation, hold edges of processor with your thumb and index fingers so that the notch is aligned with the key on the CPU socket.

Important • Be sure to hold the processor only at the edges. Pay attenti on not to touch the

bottom of the processor (pin section).

• Note the direction of the CPU. To prevent the CPU from being inserted into the

mating socket incorrectly, a pin mark is put o n eac h of the C P U an d the s oc ket. Check the pin marks to insert the CPU into the socket correctly.

• Insert the processor while aligning the notch on the processor with the ke y

section on the CPU socket.

7. Push the CPU lightly to the socket, and push down the CPU socket holder.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

8. Push down the lever to secure the CPU.

9. Put the heat sink on the CPU.

Take care not to touch the cool sheet with your hand.

Important Install the heat sink in correct direction as shown in the figure below.

Front

Rear

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

10. Secure the heat sink with four screws.

When installing the CPU heat sink, temporarily tighten the four screws on cater corner, then tighten them securely after making sure that the heat sink has been seated in parallel with the CPU socket.

11. Install the components having been removed.

12. Install the CPU blade having been removed to the Blade Enclosure according to the User's Guide of the

Blade Enclosure.

13. If "ACPI uni-processor PC" or "ACPI single-processor PC" is shown in Driver tab under Computer,

change it to "ACPI multi-processor PC". Reboot the system according to the message, and update the system. (Refer to Installation Guide.) Perform the following procedure if:

– The system is running under the Windows operating system – The system is under the 1-CPU configuration

Any change is not required if "ACPI multi-processor PC" is set in Driver tab under Computer.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.4.2

Removal

To remove the CPU, provide the preparation of the removal following Step 1 in t he installation procedure and perform steps 3 to 10 of Chapter 2 (1.4.1 Installation) in the reverse order. To remove the heat sink, slide it a little on the level and remove it. See the second paragraph of "Important" described below.

Important • Remove the CPU only when it is defected.

• After operation, the cool sheet at the botto m of the heat sink ma y adhere to the

CPU. To remove the heat sink, first turn it left and right to have it apart from t h e CPU. If you remove the heat sink with the cool sheet adhering to the CPU, the CPU and/or the socket may be damaged.

• Put a socket cover on Processor #2 if it is equipped with no CPU.

• The operation of the CPU blade cannot be secured if the CP U is installed only

on the Processor #2 socket.

• To reinstall the CPU ha ving been removed, the cool sheet should be replaced

with a new one. Contact you sales representative.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.5

DIMM

The DIMM (Dual Inline Memory Module) is inserted into the DIMM socket on the CPU blade. The CPU blade includes 16 DIMM sockets.

Important • The DIMM is easily affected by static electricity. Handle the DIMM after making

your body contact with a metallic frame section of the server to discharge the static electricity on your body. Do not make bare hands contact with terminals and components on the DIMM. In addition, do not put the DIMM on a desk directly. For static notes, refer to “Handling precautions (for Anti-static Measures)”.

• Do not use any DIMM not approved by NEC. If an unapproved third party's

DIMM is installed in the server, not only the DIMM but als o the CPU blade may be defected. You will be charged by any repair of a malfunction or defect caused by such a device within the warranty period.

Note

• Up to 512 GB memory can be added.

• In the standard configuration, the CPU blade does not contain memory. The memory

is a required option.

CPU blade

DIMM socket (CPU#2) (From top: CPU2_DIMM3, CPU2_DIMM7, CPU2_DIMM4, CPU2_DIMM8

DIMM socket (CPU#1) (From top: CPU1_DIMM1, CPU1_DIMM5, CPU1_DIMM2, CPU1_DIMM6

DIMM socket (CPU#2) (From top: CPU2_DIMM6, CPU2_DIMM2, CPU2_DIMM5, CPU2_DIMM1

DIMM socket (CPU#1) (From top: CPU1_DIMM8, CPU1_DIMM4, CPU1_DIMM7, CPU1_DIMM3

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.5.1

Adding Order and Precautions

• Adding order depends on the number of CPUs installed.

– 1-CPU configuration:

Install DIMMs starting from the smallest DIMM slot number.

– 2-CPU configuration:

Alternately install DIMMs starting from the smallest DIMM slot number of each CPU.

• Install DIMM one by one.

• Install DIMMs starting from the largest capacity and from the smallest slot number.

• Registered DIMMs and Unbu ffered DIMMs cannot be mixedly installed. If installed mixedly, the CPU blade

will fail to operate correctly.

• If the CPU blade does not have CPU#2 instal led, DIMM slots CPU2_DIMM1 to CPU2_DIMM8 are

unavailable.

1.5.2

Installation

Install the DIMM on the CPU blade according to the following procedure:

1. Remove the top cover and air duct according to Chapter 2 (1.3.1 Removal of top cover) and (1.3.2

Removal of air duct).

2. Push the DIMM into the socket straight.

If the DIMM is inserted into the DIMM socket, the lever is automatically closed.

Important • Make sure of the orientation of the DIMM. The connecting side of the DIMM has

a cut-out to prevent an incorrect insertion.

• Use extreme care when inserting a DIMM. Applying too much pressure can

damage the DIMM and/or connector.

3. Close the lever firmly.

4. If you need to install two or more DIMMs, install them according to steps 2 throug h 4.

5. Install the top cover and air duct accordin g to Chapter 2 (1.3.3 Installation of top cover and air duct).

6. Install the C PU blade having been removed to the Blade Enclosure according to the User's Guide of

the Blade Enclosure.

7. Make sure that no error message appears on the POST screen.

If any error messages are displayed, refer to Chapter 3 (1. POST Error Message) in "Maintenance Guide".

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

8. Run SETUP and select menus in the order of Advanced and Memory Configuration to make sure

that the status of installed DIMM is "Normal" (refer to Chapter 2(1. System BIOS) in "Maintenance Guide".).

9. Set the paging file size to a value larger than the recommended value (installed memory * 1.5) (for

Windows). Refer to Installation Guide for more information.

1.5.3

Removal

To remove DIMMs, remove the top cover and air duct according to Chapter 2 (1.3.1 Removal of top cover) and (1.3.2 Removal of air duct), and then perform steps in Chapter 2 (1.5.2 Installation) in reverse order.

After DIMMs were removed, make sure that no error message appears in POST. If any error messages are displayed, refer to Chapter 3 (1. POST Error Message) in "Maintenance Guide". Run SETUP and select Yes after selecting Advanced → Memory Configuration → Memo ry Retest. Restart

the CPU blade to clear the error information of the removed DIMM (refer to Chapter 2 (1. System BIOS) in "Maintenance Guide".).

Set the paging file size to a value larger than the recommended value (installed memory * 1.5) (for Windo ws). Refer to the Installation Guide for more information.

Note

To remove the defected DIMM, check the error message appearing in POST or NEC ESMPRO to confirm the CPU blade on which the detected DIMM is installed.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.6

Mezzanine Card

The CPU blade can contain two mezzanine cards for blade which allows an extension of network or a file device feature.

To install a mezzanine card, use the mezzanine card slot installed on the CPU bl ade. The mezzani ne card slot is factory-installed on the CPU blade.

Important • The mezzanine card is extremely sensitive to static electricity. Make sure to

touch the metal frame of the server to disch arge static electricity from your body before handling the mezzanine card. Do not touch the terminals and parts on the mezzanine card by a bare hand and place the cards directly on the desk. For static notes, refer to “Handling precautions (for Anti-static Measures)”.

• A combinatio n of boards which can be installed in the Blade Enclosure u nder

certain restrictions. Contact your sales representative for details.

Note

Some optional mezzanine cards use expansion ROMs on the boards. Refer to the manual shipped with the board to check whether the expansion ROMs should be required. Use the BIOS setup utility "SETUP" for the setting. Refer to Chapter 2 (1. System BIOS) in "Maintenance Guide".

CPU blade

Mezzanine card slot (Type 2)

Mezzanine card slot (Type 1)

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.6.1

Notes

Note the followings in the installation or removal of the mezzanine card.

• Be careful not to make your hands touch the terminals of the mezzanine card slot directly. If you do not

keep it, the oil and/or dirt on the hands may adhere to the terminals to result in contact failure.

• For the optional ROMs on the unbootable LAN device, set "Disabled" with the BIOS SETUP utility.

• If a bootable mezzanine card (such as Fibre Channel controller or LAN card) is installed, check the boot

priority on the Boot menu of the BIOS SETUP utility.

• The slot number for the Type 1 mezzanine card is "MEZ1", and "MEZ2" for Type 2 mezzanine card.

• 1000BASE Adapter (4ch) (N8403-077F) can be installed only in the Type 2 mezzanine card slot.

1.6.2

Installation

Install a mezzanine card in mezzanine card slot in the following procedure.

Important There are two types of mezzanine card for blade, Type 1 and Type 2.

The Type 1 mezzanine card can be installed in either of connectors Type 1 and Type

The Type 2 mezzanine card can be installed in Type 2 connector only.

To install the mezzanine card, start installation from the bottom slot (for Type 1).

Note

Before installing mezzanine card, make sure that the connection port on the card engages

with the connector on the mezzanine card slot.

1. Remove the top cover and air duct according to Chapter 2 (1.3.1 Removal of top cover) and (1.3.2

Removal of air duct).

2. Confirm the position of the slot to install the mezzanine card.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

3. From top of the CPU blade, position the connector of the mezzanine so that it aligns the connector of

the mezzanine card slot, and insert the mezzanine card straight into the slot.

Type 1

Type 2

Important • Do not make your body contact with the terminals on the board. Some

malfunction may occur if the board is installed with dirt a nd/or oil adhering to the terminals.

• Insert the mezzanine card straight into the connector. The terminal or

connector may be damaged if it is inclined.

• If the board cannot be installed securely, remove the board once and then

install it again. Adding excess force to the board may cause the board to be damaged. Keep the removed dummy memory for future use.

4. Push the connector of mezzanine card with fingers firmly toward the CPU blade to connect the card to

the slot.

5. Tighten the two fixing screws to fix the mezzanine card to the spacer on the CPU blade.

6. Install the component you have removed in earlier steps.

7. Install the C PU blade having been removed to the Blade Enclos ure according to the User's Guide of

the Blade Enclosure.

8. Turn on the power of the CPU blad e. Make sure that no err or messag e ap pears in POST.

If any error messages are displayed, refer to Chapter 3 (1. POST Error Message) in "Maintenance Guide".

9. If needed, run the BIOS configuration utility of the installed board to provide setup for the board.

The existence of the utility and its start and operation procedures vary dependin g on the type of the board. Refer to the documentation coming with the board for details.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.6.3

Removal

To remove Mezzanine card, remove the top cover and air duct according to Chapter 2 (1.3.1 Removal of top cover) and (1.3.2 Removal of air duct), and then perform steps in Chapter 2 (1.6.2 Installation) in reverse order.

After Mezzanine card is removed, make sure that no error message appears in POST. If any error messages are displayed, refer to Chapter 3 (1. POST Error Message) in "Maintenance Guide".

Important • Pay attention not to make the air duct hit any electronic component on t he C PU

blade.

• Pay attention not to make the air duct hit any electronic comp one nt o n t he CP U

blade.

• If SSD is installed on air duct, handle the air duct with care not to give any

shock to SSD.

• Pay attention to orientation of guide key of SSD cable connector.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.7

Solid State Drive (SSD)

The CPU blade can contain up to two 2.5-inch Solid State Drive. See the next and the subsequent sections for installation order and installation location.

Important • The Solid State Drive is extremely sensitive to static electricity. Make sure to

touch the metal frame of the server to disch arge static electricity from your body before handling the Solid State Drive. Do not touch the terminals and parts on the Solid State Drive by a bare hand and place the Solid State Drive directly on the desk. For static notes, refer to “Handling precautions (for Anti-static Measures)”.

• An optional S olid State Drive may contain operating system. Be very careful

when handling the drive.

• Do not use an y Solid State Dri ves not ap pro ved by NEC. I f an unappro ved thir d

party's Solid State Drive is installed in the CPU blade, not on ly the Solid State Drive but also the CPU blade may be defected.

• If Solid State Dr ives of different disk capacities co-exist in the CPU Blade, the

system can operate normally. However, to use the Solid State Drives in RAID configuration, use Solid State Drives of the same model number.

• An SSD bracket and screws are not provided with the optional Solid State

Drive. Use them that come with the CPU blade.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.7.1

Installation

Install the Solid State Drive in the following procedure. Install the first Solid State Drive in SSD bay 0 (connector: yellow), then the sec ond Solid State Drive in SSD

bay 1 (connector: blue).

1. Mount an SSD bracket to Solid State Drive with two screws.

Important • Use the SSD bracket and screws that come with the CPU blade.

• Be aw are of mounting direction of SSD bracket. (As shown in the figure, the

labeled surface of Solid State Drive and screw holes of bracket must face the same direction.)

2. Remove the top cover and air duct according to Chapter 2 (1.3.1 Removal of top cover).

3. Locate the SSD bay to install Solid State Drive. Install the first Solid State Drive in SSD bay 0

(connector: yellow), then the second Solid State Drive in SSD bay 1 (connector: blue).

SSD bay 0

SSD bay 1

SSD bay 0

SSD bay 1

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

4. Remove a single scre w from dummy SSD.

5. Lift the screw hole on dummy SSD, and remove the dummy SSD from SSD bay while tilting the

dummy SSD.

Important • Keep the removed dummy SSD for future use.

• A screw remo ved from dummy SSD should be used to secure the Solid State

Drive described in next step.

6. Connect SSD cable to SATA connector on Solid State Drive.

Important • Pay attention to orientation of connector of SSD cable.

• SSD cable connector marked as "SSD0" is used for Solid State Dri ve to be

installed in SSD bay 0, and "SSD1" is for Solid State Drive to be installed in SSD bay 1.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

7. Tilt the Solid State Drive, engage it with a latch on SSD bay, and seat the Solid State Drive in SSD

bay.

8. Fix the Solid State Drive to SSD bay with a screw you have removed from dummy SSD in earlier step.

9. Route the SSD cable so that it is settled in the cable lane of air duct cover.

10. Install the component you have removed in earlier steps.

11. Install the CPU blade having been removed to the Blad e Enclosure according to the User's Guide of

the Blade Enclosure.

12. Turn on the po wer of the CPU blade. Make sure t hat no error message associate d to Solid State Drive

appears in POST. For details on POST error messages, refer to Chapter 3 (1. POST Error Message) in "Maintenance Guide".

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.7.2

Removal

To remove the Solid State Drive, remove the top cover according to Chapter 2 (1.3.1 Removal of top cover), and then perform steps 4 through 8 of Chapter 2 (1.7.1 Installation) in reverse order.

Important • Be sure to install dummy SSD after the Solid State Drive is removed. If not, the

CPU blade may fail to work properly.

• Keep the SSD bracket and sc rews removed from Solid State Drive for future

use.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.7.3

Replacement

Depending on the operating system and/or server management software to be used, So lid State Drives must be replaced in the defined procedure to manage the Solid State Drives app ropriately.

If Windows is used as OS and NEC ESMPRO Manager and NEC ESMPRO Agent are used as the server management software, replace the Solid State Drives in the following procedure. To do these jobs, you should log on to the system as a user having the administrator authority.

The working procedure varies depending on the existence of the system partition and mirrored volume. Replace the Solid State Drives in the procedure meeting your system environment based on the figure below.

START

Is the solid disk drive configured

as RAID1?

Replace the solid state drive,

and rebuild the drive.

Is mirror v olume used ?

Does system partition exist in

solid state drive to be replaced?

Does system partition exist in

solid state drive to be replaced?

Is the source drive for

creating mirror?

See Procedure 3. See Procedur e 1. See Proced ure 2.

END

Yes

Yes No

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

(1)

Procedure 1

1. Shutdown the CPU blade system and turn off the power of the CPU blade.

2. Replace the Solid State Dr ive.

3. Set up the system again.

Important Because the data cannot be recovered in this procedure, take the proper action

such as data backup if necessary.

(2)

Procedure 2

1. Delete all the volumes and partitions on the Solid State Drive to be removed.

To delete volumes and partitions, select Programs → Administrative Tool → Computer Management → Disk Management from the Start menu. Select Delete volume / Delete partition from the menu appearing by right-clicking on

Volume/Partition.

Important • Delete volumes and partitions carefully. Pay attention not to delete volumes

and partitions from a normal disk.

• The volume and partition deletion disables the data to be recovered. Take the

proper action such as data backup if necessary.

2. Shutdown the CPU blade system and turn off the power of the CPU blade.

3. Remove the Solid State Drive.

4. Install the new Solid State Drive.

5. Turn on the power of the CPU blad e.

6. Delete the removed disk.

To delete the disk, select Program → Administrative Tool → Computer Management → Disk Management from the Start menu. Right-click the removed disk in the Disk Management menu to select Delete disk.

7. Import the installed Solid State Drive.

To import the disk, select Program → Administrative Tool → Computer Management → Disk Management from the Start menu. The installed drive has a different format. Right-click on the installed drive and select Import disk of different format.

8. If NEC ESMPRO Agent is used, reset the Solid State Drive (refer to Chapter 2 (1.7.4 Resetting

Management Information).

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

(3)

Procedure 3

1. Cancel the mirroring configuration.

To release the mirror, select Program →Administrative Tool → Computer Management → Disk Management from the Start menu. Select Cancel mirroring from the menu appearing by right-clicking on the mirrored volume.

2. Delete all the volumes and partitions on the Solid State Drive to be removed.

To delete the volume/partition, select Program → Administrative Tool → Computer Management → Disk Management from the Start menu. Select Delete volume / Delete partition from the menu appearing by right-clicking on the

volume/partition.

Important • Delete volumes and partitions carefully. Pay attention not to delete volumes

and partitions from a normal disk.

• The volume and partition deletion disables the data to be recovered. Take the

proper action such as data backup if necessary.

3. Shutdown the CPU blade system and turn off the power of the CPU blade.

4. Remove the Solid State Drive.

5. Install a Solid State Drive.

6. Turn on the power of the CPU blad e.

7. Delete the removed disk.

To delete the disk, select Program → Administrative Tool → Computer Management → Disk Management from the Start menu. Right-click on the removed disk in the Disk Management screen and select Remove disk.

8. Import the installed Solid State Drive.

9. Add the mirrored volume.

To add the mirrored volume, select Program → Administrative Tool → Computer Management → Disk Management from the Start menu. Select Add mirror from the menu appearing by right-clicking on the volume to which the mirror is desired to be added.

10. If NEC ESMPRO Agent is used, reset the Solid State Drive (refer to Chapter 2 (1.7.4 Resetting

Management Information).

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.7.4

Resetting Management Information

Reset the management information on the replaced Solid State Drive in the following proced ure.

1. Select Settings → Control Panel → NEC ESMPRO Agent from the Start menu.

NEC ESMPRO Agent Properties is displayed.

2. Click on the General tab in NEC ESMPRO Agent Properties.

3. Select Storage Setting… in the General tab.

Storage is displayed.

4. Click on the Reset tab in Storage.

5. After selecting the replaced Solid State Drive in Hard disk drive list, click on OK. (The Solid State

Drives are also listed in Hard disk drive list.) The management information on the replaced Solid State Drive is reset.

6. Close the dialog box.

7. Close NEC ESMPRO Agent Properties.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.8

Use of Internal Hard Disk Drives in the RAID System

This section describes how to use the Hard Disk Drives installed in the HDD cage at the front of the server in the RAID System.

Important

• If you use Har d Disk Drives in the RAID System or change the RAID

level, initialize the Hard Disk Drives. If the Hard Disk Drive contains valuable data, be sure to backup the Hard Disk Drive before installing the RAID Controller and configuring the RAID System.

• Do not change the mode to hibernate when building a RAID System.

Note

In the RAID System, use Hard Disk Drives that have the same specifications (capacity, rotational speed, and standard) for each Disk Array.

Tips

• Logical Drives can be created even with only one Physical Device.

• Understand the characteristics of each RAID Controller such as available RAID

levels or Hard Disk Drives and choose an appropriate RAID Controller.

• Logical Drives except for RAID0 have a smaller usable capacity compared to the total capacity of the Hard Disk Drive in the Logical Drive, while disk reliability increases.

You can set up a RAID system by using the on-board RAID controller (LSI Embedded MegaRAID™).

To use this RAID system, it is necessary to install two Solid State Drives on the serv er. For details on the procedure of installing Solid State Drives, refer to Chapter 2 (1.7 Solid State Drive (SSD)) in this manual.

1.8.1

Enabling a RAID System

You can use the installed Solid State Drives as single solid state drives or as a RAID s ystem. To set up the installed Solid State Drives as a RAID system, select Advanced, PCI Configuration, and

Onboard SCSI from the BIOS Setup menu, and then set Option ROM Scan to Enabled. (For details, refer to Chapter 2 (1. System BIOS) in the “Maintenance Guide”.)

Tips

The Solid State Drives are set to be used as a RAID system as the factory default.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.8.2

Notes on setting up a RAID System

Note the following points when setting up a RAID System.

• The number of Solid State Drives required varies in each RAID level.

The number of Solid State Drives required to set up a RAID System

RAID level

Minimum Maximum

RAID 0 1 1 RAID 1 2 2

• It is recommended to install Solid State Drives with the same model number.

• If you intend to install the OS to the RAID System, the process from RAID configuration to OS installation

can be easily completed by using the EXPRESSBUILDER. If you wish to install the OS manually, use a RAID System Configuration utility (WebBIOS). The utility can be run during POST which starts immediately after the server is turned on. For details on the procedure of configuring a Lo gical Drive, refer to Chapter 2 (4. RAID System Configuration) in "Maintenance Guide".

Important

Do not change the mode to hibernate when building a RAID System.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.9

Trusted Platform Module Kit

The CPU blade can be equipped with Trusted Platform Module Kit used for encryption o f Solid State Drive. Use the connector for Trusted Platform Module Kit on CPU blade to install Trusted Plat form Module Kit. (The

connector for Trusted Platform Module Kit is factory-installed on CPU blade.)

Important Trusted Platform Module Kit is extremel y sensitive to static electricity. Be sure to

touch the metal frame of the ser ver to discharge static electricity from your body before handling the Trusted Platform M odule Ki t. Do not touch the Trusted Platform Module Kit terminals or parts with bare hand or place the Trusted Platfor m Module Kit directly on the desk. For static notes, refer to “Handling precautions (for Anti-static Measures)”.

Connector for Trusted Platform Module Kit

CPU blade

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.9.1

Installation

Install the Trusted Platform Module Kit according to the following procedure:

1. Remove the top cover according to Chapter 2 (1.3.1 Removal of top cover).

2. Insert the projection of Trusted Platform Module Kit into the groove on CPU blade c hassis, and slowly move Trusted Platform Module Kit until the connector on Trusted Platform Module Kit is aligned with Trusted Platform Module Kit connector on CPU blade.

Important • Do not touch the terminals of the card with your bare hand. Fingerpri nts and

dust left on it causes the CPU blade to malfunction.

• Insert TPM perpendicularly into the connector. Inserting Trusted Platform

Module Kit with being inclined may damage connector pins and/or connectors.

• If you have trouble installing the Trusted Platfo rm Module Kit, remo ve the TPM

once and try again. If you apply excessive pressure on Trusted Platform Module Kit, a Trusted Platform Module Kit might be damaged.

3. Mount Trusted Platform Module Kit to the CPU blade an d secure it with a single screw.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

4. Mount the support bracket for Trusted Platform Module Kit kit. Align the positioning key with the groove, and secure it with two screws. (T wo types of screws are provided. Use the flat head screw for Trusted Platform Module Kit side, and the pan hea d screw for center side of chassis.)

5. Install the components y ou removed in earlier steps.

6. Install the C PU blade having been removed to the Blade Enclos ure according to the User's Guide of the Blade Enclosure.

7. Turn on the power of the CPU blad e. Make sure that no err or messag e ap pears in POST. If any error messages are displayed, refer to Chapter 3(1. POST Error Message) in "Maintenance Guide".

1.9.2

Removal

To remove the Trusted Platform Module Kit, remove the top cover according to Chapter 2 (1.3.1 Removal of top cover), and then perform steps 2 through 4 of Chapter 2 (1.9.1 Installation) in reverse order.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.10

Internal Flash Memory

The CPU blade can be equipped with Internal Flash Memory (USB memory embedded card) that contai ns information of EXPRESSBUILDER.

Use the connector for Internal Flash Memory on CPU blade to install Internal Flash Memory. (The connector for Internal Flash Memory is factory-installed on CPU blade.)

Important Internal Flash Memory is extremely sensitive to static electricity. Be sure to touch

the metal frame of the server to discharge static electricity from your bod y before handling the Internal Flash Memory. Do not touch the termina ls or parts of Internal Flash Memory with bare hand or place the Interna l Flash Memory directly on the desk. For static notes, refer to “Handling precautions (for Anti-static Measures)”.

Connector for Internal Flash Memory

CPU blade

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

1.10.1

Notes

The data in EXPRESSBUILDER is not copied in Internal Flash Memory. Refer to Chapter 2 (5.3 Utilities Provided by EXPRESSBUILDER) on in "Maintenance Guide".

1.10.2

Installation

Install the Internal Flash Memory according to the following procedure:

1. Remove the top cover according to Chapter 2 (1.3.1 Removal of top cover).

2. Insert the projection of Internal Flash Memory into the groove on CPU blade chassis, and slowly

move Internal Flash Memory until the connector on Internal Flash Memory is aligned with Internal Flash Memory connector on CPU blade.

Important • Do not touch the terminals of the card with your bare hand. Fingerpri nts and

dust left on it causes the CPU blade to malfunction.

• Insert Internal Flash Memory perpendicularly into the connector. Inserting

Internal Flash Memory with being inclined may damage connector pins and/or connectors.

• If you have trouble installing the Internal Flash Memory, remove the Internal

Flash Memory once and try again. If you apply excessi ve pressure on Internal Flash Memory, the Internal Flash Memory might be damaged.

3. Mount Internal Flash Memory to the CPU blade and secure it with a single screw.

1. Installing Internal Optional Devices

Express5800/B120e-h User's Guide

Chapter 2 Preparations

4. Mount the support bracket for Internal Flash Memory.

Align the positioning key with the groove, and secure it with two screws. (Two types of screws are provided. Use the flat head screw for Internal Flash Memory, and the pan head screw for center side of chassis.)

5. Install the component you have removed in earlier steps.

6. Install the CPU blade having been removed to the Blade Enclosure according to the User's Guide of

the Blade Enclosure.

7. Turn on the power of the CPU blade. Make sure that no error message appears in POST.

If any error messages are displayed, refer to Chapter 3 (1. POST Error Message) in "Maintenance Guide".

1.10.3

Removal

To remove the Internal Flash Memory, remove the top cover according to Chapter 2 (1.3.1 Removal of top cover), and then perform steps 2 and 3 of Chapter 2 (1.10.2 Installation) in reverse order.

2. Installation and Connection

Express5800/B120e-h User's Guide

Chapter 2 Preparations

Installation and Connection

This section describes how to position the CPU blade and connect cables.

2.1

Installation

Install the CPU blade in the dedicated Blade Enclosure. Refer to the User's Guide of Blade Enclosure for location appropriate to Blade Enclosure, and how to install the CPU blade.

Important • The CPU blade is extremely sensitive to static electricity. Make sure to touch

the metal frame of the CPU blade to discharge static electricity fro m your bo dy before handling the CPU blade. Do not touch the pins, leads, or circuitr y and place the CPU blade directly on the desk. For static notes, refer to “Handling precautions (for Anti-static Measures)”.

• Do not block air vents of the CPU blades, Blade Enclosures, power supply

units, and additional FAN units.

2. Installation and Connection

Express5800/B120e-h User's Guide

Chapter 2 Preparations

2.1.1

Checking MAC Address

Be sure to check the MAC addresses before installing a CPU blade in the Blade Enclosure. A MAC address indicates the address specific for the network. It is expressed by 12-digit alphanumeric. MAC

addresses are stored in LAN riser card which is a required option of CPU blade. The number of MAC addresses stored in card depends on type of LAN riser card.

• Dual Port 1GBASE riser card kit(N8403-061F): 2

• Dual Port 10GBASE riser card kit(N8403-062F): 8

• Dual Port 10GBASE riser card kit(N8403-064F): 16

A MAC address is indicated in the area of LAN riser card as shown in the figure below.

The MAC address of LAN port is derived by adding the base value in the table below for the address. For convenience, the added values of in the table below are quoted in decimal number. The MAC address is

actually used, so will be shown in a hexadecimal number, please be careful.

Important f the NPAR feature is disabled, MAC addres ses which can be used one (or two;

iSCSI offload type) will be per physical port. To derive the M AC address, please refer to the PF0 of each physical port in the table below.

• Dual Port 1GBASE riser card kit(N8403-061F): LAN port

number

Network MAC address

1 0 2 +2

• Dual Port 10GBASE riser card kit(N8403-062F): LAN port

number

LAN port partition number

(PF*)

Network MAC address

0 0 1 +4 2 +8

3 +12 0 +2 1 +6 2 +10

3 +14

Label indicating MAC address

DG7xxx xxxxxxxxx

XXXXXXXXXXXX

MAC address (12 characters)

2. Installation and Connection

Express5800/B120e-h User's Guide

Chapter 2 Preparations

• Dual Port 10GBASE riser card kit(N8403-064F):

LAN port

number

LAN port partition number

(PF*)

Network MAC address iSCSI MAC address

0 0 +1 1 +4 +5 2 +8 +9

3 +12 +13 0 +2 +3 1 +6 +7 2 +10 +11

3 +14 +15

＊PF : Physical Function

The MAC addresses can be checked from the proper Windows command.

• Windows

Enter "ipconfig /all" for the command prompt or from Run in the Start menu to see the indicated physical address part.

• Linux

Enter "ifconfig" for prompt to see the indicated HWaddr.

• You may use the remote control feature of E XPRES SSCOPE Engine 3 (BMC) to check the MAC address.

2. Installation and Connection

Express5800/B120e-h User's Guide

Chapter 2 Preparations

2.2

Connecting Peripheral Devices

Connect peripheral devices to the CPU blade.

Tips

Contact the maintenance engineer in your sales representative if you have any requests on the system configuration including the connection to the uninterruptible power supply system or auto power controller and the time schedule operation.

Important If you are installing the CPU blade in the Blade Encl osure (SIGMABLADE), follow

instructions described in the User's Guide of the Blade Enclosure.

WARNING

Be sure to observe the following precautions to use the server safety. Failure to observe the precautions may cause death or serious injury. For details, refer to Safety precautions in Precautions for Use.

• Do not hold the power plug with a wet hand.

• Do not connect earth lines to any gas tubes.

CAUTION

• Do not plug the power cord in to an improper power source.

• Do not connect the power cord to an outlet that has an illegal number of connections.

• Insert the power plug into the outlet as far as it goes.

• Use the authorized power cord only.

• Do not con nect or disconnect any interface c able with the power cord of the ser ver plugged

to a power source.

• Do not use any unauthorized interface cable.

2. Installation and Connection

Express5800/B120e-h User's Guide

Chapter 2 Preparations

In the ordinary operation, SUV cables may not be connected to a CPU blade. Proper cable(s) should be connected to the USB, serial, and/or VGA ports on the CPU blade in the following cases:

• Using a Flash FDD with the server installed in the N8405-016F/016AF/016BF/016CF/040F/040AF Blade

Enclosure

• Performing maintenance work

• Updating BIOS and firmware

Use K410-150(00) SUV cable connector of CPU blade. (K410- 150(00) SUV cable is a standard acc essory for the Blade Enclosure (SIGMABLADE)).

Important • Do not use an external DVD-ROM drive connected via the K410-150(00) SUV

cable to install an operating system.

• Use the internal DVD-ROM drive of Blade Enclosure to install an operating

system.

The K410-150(00) SUV cable has the USB, serial interface, and monitor connectors at the ends. Connect a proper device at each of the ends. The shape of SUV cable may differ depending on shipment time, however, functionality does not chan ge.

To CPU blade

To USB devices

To monitor

To serial interface device

To monitor

To USB devices

(This connector has two ports.)

To CPU blade

2. Installation and Connection

Express5800/B120e-h User's Guide

Chapter 2 Preparations

Important • To connect a peripheral or interface cable provided by a vendor other than

NEC (or third party) to the CPU blade, make sure that the device is available for the CPU blade. Some third party devices are not available for the CPU blade.

• The serial port connector cannot be directly connected with the leased line.

• Do not connect /disconnect the SUV cable or add/remove the USB device until

the operating system starts running. To connect/disconnect the SUV cable or add/remove the USB device after OS startup, follow restrictions of operating system. If the device having serial interface is connected, first power off the CP U blade and destination device, and remove the power cord from t he d estina tion device before connecting/disconnecting SUV cable or serial cable. Fai lure to follow it may cause the devices to be defected due to the potential difference between them.

• The USB device may not work correctly in USB 2.0 High Speed mode

depending on type of USB device or cable len gth. In s uch a ca se, use a s horte r cable, or use a USB hub that supports USB2.0 High Speed mode.

2. Installation and Connection

Express5800/B120e-h User's Guide

Chapter 2 Preparations

2.2.1

USB Connection by K410-150(00) SUV Cable

Connect an external DVD-ROM drive, keyboard, and mouse according to the figure sho wn below. Use the separately priced K410-150(00) SUV cable (or a standard accessory for the Blade Enclosure (SIGMABLADE).

However, when using a display unit, keyboard, and mouse con nected to the Blade Enclosure by using the KVM selection feature of the Blade Enclosure, do not connect those devices by way of a SUV cable.

2.2.2

Connecting with Network

The CPU blade is connected with network via the Blade Enclosure. Refer to the User's Guide of the Blade Enclosure for details.

Flash FDD

USB

DMP

Display unit

Self-powered USB hub

Mouse

* Use the USB hub and external DVD-ROM drive supported by this CPU blade.

External DVD-ROM drive

Keyboard

2. Installation and Connection

Express5800/B120e-h User's Guide

Chapter 2 Preparations

2.2.3

Connecting with UPS

To connect the power cord from the Blade Enclosure to an interruptive po wer supply (UPS), use outlet socket on the rear of the UPS. Refer to the manual that comes with the UPS for details.

When the power cord from the Blade Enclosure is connected to a UPS, you may need to change the BIOS SETUP of the CPU blade to link with power supply from the UPS.

Run BIOS SETUP, and select Server → AC-LINK and change parameter appropriately. Select Pow er On for automatic operation via UPS. For more information, refer to Chapter 2 (1.2.4 Server) in Maintenance Guide.

Option slot

Computer interface port (USB)

Reset button for

overload prevention

Outlet socket

Input connector

(NEMA5-15P)

Voltage sensitivity setting button

Computer interface port (COM)

Connector for TVSS device

Express5800/B120e-h User's Guide

NEC Express5800 Series Express5800/B120e-h

Setup

This chapter describes how to set up the CPU blade.

1. Turning on the Server

POST (Power-On Self-Test) is explained in this section.

2. System BIOS (Setup)

You can customize the BIOS settings by following the instructions in this section.

3. EXPRESSSCOPE Engine 3

EXPRESSSCOPE Engine 3 provides useful features through the Baseboard Management Controller (BMC).

4. EXPRESSBUILDER

EXPRESSBUILDER helps you to install Windows and maintain the server.

5. Installing Software Components

You can install Windows and bundled software by following the instructions in "Installation Guide (Windows)".

6. Device Identification

Describes ID lamp provided in the server.

7. Power-off of Blade Server

Turn off power when not using the server.

1. Power-on of Blade Server

Express5800/B120e-h User's Guide

Chapter 3 Setup

Power-on of Blade Server

There are the following three ways to turn on the power of the CPU blade. Turn on the power of the CPU blade in any of the three ways after turning on the powers of the display unit and peripherals conn ected to the CPU blade.

Important Perform the power-on operation of the CPU blade b y either the use of the POWER

switch or the remote power-on after the period of 60 seconds or longer has passed from the supply of AC power to every pow er unit (POWER lamp on CPU blade is li t amber). The power-on operation w ithin the period of 60 seconds from the suppl y of AC power to every power unit may not turn o n the power of the CPU blade. If so, turn on the power of the CPU blade by using the POWER switch after making sure that the AC power is supplied to every power unit.

Note

If a power cord on the Blade Enclosure is connected to a power controller including an uninterruptible power supply (UPS), make sure that the power of the power controller is turned on.

Tips

When the power is supplied to the CPU blade, the initial diagnosis is executed for about 60 seconds. In this period, the POWER switch is disabled. Power on the CPU blade about 60 seconds immediately after you installed the CPU blade or turned on the power.

1. Power-on of Blade Server

Express5800/B120e-h User's Guide

Chapter 3 Setup

1.1

Power ON from CPU Blade

Press the POWER switch on the panel of the CPU blade (the POWER lamp on the CPU blade goes on green).

DMP

RST

POWER lamp

POWER switch

1. Power-on of Blade Server

Express5800/B120e-h User's Guide

Chapter 3 Setup

1.2

Power ON from Network Serial Port

Depending on the BIOS setting of the CPU blade, the power of the CPU blade may be automatically turned on by a proper packet received from the network or via the modem connected to the serial port.

This power-on procedure can be specified by setting Wake On Events of System Hardware in the BIOS SETUP Utility.

1.3

Power ON from Remote Console

The power of the CPU blade can be turned on by using remote control feature of EXPRESSSCOPE Engine 3 (BMC).

1.4

Operation after Power ON

If the CPU blade is connected with a display unit, the NEC logo appears on the screen of the display unit after a while from the power-on.

Important

Do not power off the server until NEC logo and some message appears.

While the NEC logo appears, the CPU blade runs the self-diagnosis program (POST) to diagnos e the CPU blade itself. Refer to Chapter 3 (1.5 POST).

1. Power-on of Blade Server

Express5800/B120e-h User's Guide

Chapter 3 Setup

1.5

POST

POST (Power On Self-Test) is the self-diagnostic program stored in the CPU blade. When you power on the CPU blade, the system automatically runs POST to check the motherboard, memory

module, processor (CPU), keyboard, and mouse. POST also displays the start-up message of utilities, while in progress.

Usually, you do not need to check the contents of POST.

However, check messages displayed at POST in

the following cases.

• When you use the CPU blade for the first time.

• When the CPU blade appears to fail.

• When any error message is displayed

1.5.1

POST Execution Flow

The following describes the progress of POST in the chronological order.

Important • Do not make unnecessary key entries or perform mouse operations while

POST is in progress.

• Some system configurations may display the message "Press Any Key" to

prompt a key entry. This message is driven by BIOS of an installed option al board. Make sure to read the manual that comes wi th the optio nal board bef ore any key entry.

• Powering on the server, after you installed or removed an opt ional mezzanine

card, may display the message that indicates incorrect board configuration and suspend POST. In such a case, press the <F1> key to continue POST. Board confi guration can be made using the utility described later.

1. When the server is turned on, POST starts running, and displays messages indicating initialization of memory and PCI devices. After messages are displayed, the LOGO appears.

Note

• The keyboard becomes available after the logo is displayed.

• The screen may be switched to black (nothing is displayed) several times while the

initialization message is being displayed, however, it is not the problem.

• The initialization message may not appear depending on setting of BIOS SETUP, or when optional VGA controller is connected.

• The initialization message does not appear on Console Redirection screen of serial port.

1. Power-on of Blade Server

Express5800/B120e-h User's Guide

Chapter 3 Setup

2. If the <Esc> key is pressed, the logo disappears and the details of POST are displayed.

Tips

You can set it to show the details of POST to be displayed from BIOS menu without requiring the <ESC> key to be pressed. From the System BIOS Setup, set Quiet Boot to Disabled in the Boot menu.

3. POST displays several types of message. These messages let you know that the installed CPU or connected keyboard and mouse are detected.

Tips

Depending on the installed PCI card configuration, the memory capacity might be displayed less than actually installed physical memory. (This applies to the display of BIOS Setup utility or OS system information.)

4. After a while, POST displays the following message.

Press <F2> SETUP, <F3> Internal flash memory, <F4> ROM Utility, <F12> Network

By pressing the designated function key following messages, you can call the functions below upon completion of POST.

<F2> key: Run BIOS Setup Utility (SETUP). For information on the SETUP, refer to Chapter 3 (2

BIOS Setup Utility (SETUP).).

<F3> key: Run EXPRESSBUILDER from Internal Flash Memory (optional). For information on

EXPRESSBUILDER, refer to Chapter 3 (4. EXPRESSBUILDER).

<F4> key: Run the offline tool. For information on the offline tool, refer to Chapter 1 Maintenance

(9. Offline Tools) in "Maintenance Guide".

<F12> key: Boot from network.

Note

• If the optional Internal Flash Memory is not installed in the system, the <F3> key message will not be displayed.

• The <F3> key must be pressed within 5 seconds of the message being displayed.

• Note that the server will not boot from the Internal Flash Memory even if it is specified

to do so by pressing the <F3> key, as long as a bootable CD/DVD-ROM is set on the drive with the boot priority of CD/DVD-ROM is set to higher than Solid State Drive.

5. If a controller which has its dedicated BIOS such as a SCSI controller board is installed, a message that prompts you to start the dedicated utility to set each board is displayed.

1. Power-on of Blade Server

Express5800/B120e-h User's Guide

Chapter 3 Setup

Important • To start a dedicated utility for the RAID controller and so on when POST i s

running, do as follows.

1. Make sure that you do not press any key before beginning this work.

2. Press a "Modifier Key" (such as <Ctrl> key) first, and hold down the "Modifier Key" and press a “Character key” (such as <H> key) with the "Modifier Key" pressed repeatedly until the dedicated utility starts.

• If you have failed to start the dedicated utilit y, please restart the server and

rerun POST to try again.

Example: SCSI BIOS Setup utility

Press <Ctrl> <A> for SCSISelect(TM) Utility!

The utility starts by pressing the <Ctrl> + <A> keys.

Example: If the jumper setting for an on-board RAID Controller is enabled

Press <Ctrl> <M> to Run LSI Software RAID Configuration Utility

The utility starts by pressing the <Ctrl> + <M> keys.

For details on the utility, refer to the manual supplied with each optional board.

Depending on the configuration, the message "Press Any Key" might appear to prompt a key entry. This is a behavior of the BIOS of the optional board. Continue to operate after checking the manual of the optional board.

6. If you have set the password using the BIOS SETUP utility, the password entry screen appears upon successful completion of POST. Up to three password entries will be accepted. Three incorrect password entries disable the system to boot. In such a case, turn off the power and wait about 10 seconds before turning on to boot the CPU blade.

Important Do not set a password before installing an OS.

7. The OS starts when POST completes.

1.5.2

POST Error Messages

When POST detects an error, it displays an error message on the screen. For descriptions of error messages, causes, and countermeasures, refer to "Maintenance Guide".

Important Take notes on the messages displayed before consulting with your maintenance

service company. Alarm messages are useful information for maintenance.

2. BIOS Setup Utility (SETUP)

Express5800/B120e-h User's Guide

Chapter 3 Setup

BIOS Setup Utility (SETUP)

This section describes how to configure Basic Input Output System (BIOS). Before you install the server and add or remove optional devices, make sure you have read and understood

this section to configure properly.

2.1

Overview

BIOS Setup Utility (SETUP) is a utility to do basic hardware settings. This utility is installed in a flash memory in the server as standard and can be run without requiring a media for boot.

BIOS settings were configured with optimal settings before the server was shipped to you. Therefore, in most of cases, you should not need to use the SETUP.

2.2

Starting and Exiting SETUP Utility

z Starting SETUP Utility

Run POST following Chapter 3 (1.5.1 POST Execution Flow). After a while, the following message will be displayed on the lower left of the screen.

Press <F2> SETUP, <F3> Internal Flash Memory, <F4> ROM Utility, <F12> Network

If you press <F2> key at this time, SETUP runs and displays Main menu upon completion of POST. (You can also press <F2> key while NEC logo appears to display Main menu.)

Tips

If the password has been set, you will be prompted to enter the passw ord at the next startup of SETUP. (The timing when prompt message appears depends on password setting.) Up to three password entries will be accepted. If you fail to enter the password correctly for three consecutive times, the server halts. (You can no longer proceed.) Power off the server.

z Exiting SETUP Utility

To save changes, select Save changes and Exit in Save & Exit menu. To discard changes, select Discard

changes and Exit in Save & Exit menu.

Tips

To restore the default setting, select Load Setup Defaults in Save & Exit menu. (The default setting may differ from that of shipping defaults.)

2. BIOS Setup Utility (SETUP)

Express5800/B120e-h User's Guide

Chapter 3 Setup

2.3

Description on On-Screen Items and Key Usage

This section shows display examples and how to control the key. Use the keyboard to work with the SETUP utility.

 Cursor keys (<↑>, <↓>)

Select an item displayed on the screen. If characters of an item are highlighted, that means the item is currently selected.

 Cursor keys (<←>, <→>)

Select top menus including Main, Advanced, Security, Server, Boot, and Save & Exit.

 <−> key/<+> key

Change the value (parameter) of the selected item. You cannot use this key when a menu which has on the left is selected.

 <Enter> key

Press this key to confirm the selected parameter.

 <Esc> key

Press this key to cancel pop up menu. In sub menu, press this key takes you to the previous screen. In top menu, press this key takes the following window is displayed. If you select Yes, the SETUP closes without saving the changed parameters.

Quit without saving?

[Yes] No

 <F1> key

Press this key to display help information of key usage. If you need help using the SETUP, press this key. Press the <Esc> key to go back to the original screen.

Indicates the currently displayed menu

Help

Parameters (highlighted when selected*) *: Items that cannot be specified are dimmed.

Setting items

Indicates the menu has submenus.

2. BIOS Setup Utility (SETUP)

Express5800/B120e-h User's Guide

Chapter 3 Setup

 <F2> key

If you press this key, the following window appears. If you select Yes, the previous parameter(s) are restored. However if you save parameter(s) using [Save Changes], the saved parameter(s) are restored.

Load Previous Values?

[Yes] No

 <F3> key

If you press this key, the following window appears. If you select Yes, restore the SETUP parameters of the currently selected item to the default setting. (This might be different from the parameters configured before shipment.)

Load Setup Defaults?

[Yes] No

 <F4> key

If you press this key, the following window appears. If you select Yes, the parameter you configured is saved and SETUP closes.

Save configuration and exit?

[Yes] No

2. BIOS Setup Utility (SETUP)

Express5800/B120e-h User's Guide

Chapter 3 Setup

2.4

Cases that Require Configuration

Only if a case applies to any of following cases, use the SETUP utility to change a parameter which was configured as factory setting. Other than cases described below, do not change the settings. A list of SETUP parameters and factory settings are described in Chapter 2 (1. System BIOS) in "Maintenance Guide".

Category Description To be changed Remark

Change date and time Main → System Date

Main → System Time

Configurable on OS

On/Off NumLock on power ON Boot → Bootup Numlock State

Basic

On/Off the function to display the NEC logo during POST

Boot → Quite Boot → Disabled Pressing the <Esc> key can

hide the logo. Optional board

Install RAID Controller board Advanced → PCI Configuration → PCI

Slot n Option ROM → Enabled

n is PCI slot number of the

RAID Controller

Change the boot order of devices

Boot → Boot Option Priorities →

Change the boot priority Use remote power on function (from modem)

Advanced → Advanced Chipset

Configuration → Wake On Ring →

Enabled

Use remote power on function (from RTC alarm)

Advanced → Advanced Chipset

Configuration → Wake On RTC Alarm

→ Enabled

Boot

Control from HW console terminal

Advanced → Serial Port

Configuration → Change respective

setting.

Security Set a password Security → Administrator Password

→ Enter a password

(Set a password for Administrator first

and then User)

There are two types of password; Administrator and User. Settings for User password is limited compared to for

Administrator. When the server is supplied with power from UPS, always turn on the power.

Server → AC-LINK → Power On

If the server is turned off by using POWER switch, leave it OFF even when UPS supplies power.

Server → AC-LINK → Last State

UPS Powerlink

Keep the power OFF even when UPS supplies power.

Server → AC-LINK → Stay off

2. BIOS Setup Utility (SETUP)

Express5800/B120e-h User's Guide

Chapter 3 Setup

Password

If you have set a password, a message prompt you to enter password will be displayed from the next time.

Enter password [ ]

You can attempt password entry up to 3 times. If you entered a wrong password 3 times, operation stops. (You cannot operate further.) Turn off the power.

Saving changes

If you finish configuration, select Save & Exit and then Save Changes and Exit to save changes and exit. If you wish to exit without saving the changed parameters, select Save & Exit

and then Discard Changes

and Exit.

Or if you wish to restore the setting to default values, select Save & Exit

and then Load Setup Defaults.

(The default value might be different from the factory setting.

)

3. EXPRESSSCOPE ENGINE 3

Express5800/B120e-h User's Guide

Chapter 3 Setup

EXPRESSSCOPE ENGINE 3

3.1

Overview

EXPRESSSCOPE Engine 3 provides a variety of features using BMC (Baseboard Management Controller), which is a system management LSI.

EXPRESSSCOPE Engine 3 monitors the temperature and voltage of the server. If you have the management LAN port connected to the network, you can remotely perform the following over a web browser or SSH client:

• Manage the server

• Remotely control the keyboard, video, and mouse (KVM)*

• Remotely access a CD/DVD/floppy disk/ISO image/USB memory*.

* To actualize these functions, virtual USB mass storage device (Remote FD, Remote CD/DVD, Remote

USB Memory, or Vritual Flash) is always connected as USB mass storage devices for CPU blade.

Tips

More than one removable drives other than the actual drive are displayed on the operating system of the host system. This is a normal operation and these added removable drives are the virtual removable drives reserved for the remote media function of EXPRESSSCOPE Engine 3 (*1).

Fig. 1 Exp. Windows Server 2008 R2 Computer Folder (*2)

Fig. 2 Exp. Windows Server 2008 R2 Server Manager (*2)

*1 A function to use FD/CD/DVD drives, ISO images and USB memories

connected to the management PC as drives virtually connected to the host system.

*2 The number of drives and the drive letter are different depending on system

configurations.

3. EXPRESSSCOPE ENGINE 3

Express5800/B120e-h User's Guide

Chapter 3 Setup

3.2

EXPRESSSCOPE ENGINE 3 Network Configuration

The network configuration of management LAN of EXPRESSSCOPE Engine 3 is obtained automatically from the Enclosure Manager which has DHCP server function. For detailed information on DHCP server of EM card, refer to EM Card User's Guide or Blade Enclosure User's Guide. By the factory default, DHCP is set to Enabled.

If DHCP is set to Disabled and you want to use the management LAN of EXPRESSSCOPE Engine 3, follow steps below to configure the network.

1. Run POST following Chapter 3 (1.5.1 POST Execution Flow). Wait until the following message appears on the lower left of the screen.

Press <F2> SETUP, <F3> Internal flash memory, <F4> ROM Utility, <F12> Network

2. If you press the <F4> key at this time, ROM utility starts upon completion of POST. You can also press the <F4> key while the NEC logo is being displayed to open the Off-line TOOL MENU screen.

3. The keyboard selection screen appears. Select your keyboard type. After that, the Off-line TOOL MENU screen appears. On this screen, specify the network settings for EXPRESSSCOPE Engine 3.

3. EXPRESSSCOPE ENGINE 3

Express5800/B120e-h User's Guide

Chapter 3 Setup

4. When the Off-line TOOL MENU appears, select BMC Configuration, BMC Configuration, Network, and then Property.

5. If Property is selected, the following screen is displayed. On this screen, specify whether to use DHCP and if DHCP is not used, configure IP Address/Subnet Mask.

6. It will be available for use if you access EXPRESSSCOPE Engine 3 via Web browser of management PC according to the setting.

4. EXPRESSBUILDER

Express5800/B120e-h User's Guide

Chapter 3 Setup

EXPRESSBUILDER

EXPRESSBUILDER helps you to install Windows or maintain the server.

4.1

Features of EXPRESSBUILDER

EXPRESSBUILDER provides the following features.

Features Descriptions

Setup (Windows reinstallation)

Installs Windows on your server. Easily completes the process from RAID configuration to installation of applications. To use this feature, select OS

installation in the menu after boot. Bundled software* Stores various bundled software (such as NEC ESMPRO Agent). Maintenance Diagnoses your server system. To use this feature, select Tool menu in the menu

after boot. Documents* Stores documents including Instruction Manual of the server.

* Documents and some software components are not stored in Internal Flash Memory.

4.2

Starting EXPRESSBUILDER

If you want to configure RAID System or install Windows, start EXPRESSBUILDER by using any of the following.

EXPRESSBUILDER DVD:

Set the DVD on the drive and either turn on the server or restart the server by pressing <Ctrl> + <Alt> + <Delete> keys. EXPRESSBUILDER is booted from DVD.

If you want to install any bundled software or see documents, set the DVD to a computer running Windows. Autorun menu appears automatically.

Internal Flash Memory (option):

Press <F3> key during POST. When using this option, make sure that the media was remo ved from the drive.

5. Installing Software Components

Express5800/B120e-h User's Guide

Chapter 3 Setup

Installing Software Components

Continue to install software components such as OS. Refer to the instructions below.

• Installation Guide (Windows)

Tips

If you are using Red Hat Enterprise Linux 6, see (5.1 Notes on using Red Hat Enterprise Linux 6).

5.1

Notes on using Red Hat Enterprise Linux 6

5.1.1

About the message caused by power consumption control in Red Hat

Enterprise Linux 6

The following messages may be logged to “syslog”, but these do not indicate that failures have occurred in the server.

These messages indicate that the power consumption of a CPU blade has reached the upper limit value for ceiling control.

The power consumption in the entire system is controlled by the EM card installed in the blade enclosure, and the EM card controls the upper limit values of the CPU blades for ceiling control dynamically according to the power consumption of each CPU blade.

When the power consumption of a CPU blade has reached the upper limit value, the value is changed automatically by optimally allocating the power across the CPU blades, therefore, there will be no impact in the operation.

Please refer to the user's guide of the EM card for setting the power consumption control on the EM card.

■ Sample Message 1 kernel: CPU6: Core power limit notification (total events = 196670) kernel: CPU21: Package power limit notification (total events = 196453) kernel: CPU17: Core power limit normal kernel: CPU23: Package power limit normal mcelog: Processor 3 below trip temperature. Throttling disabled

These messages will be logged as many times as the number of logical CPU.

■ Sample Message 2 [Hardware Error]: Machine check events logged

You can distinguish between the messages for failures and for power capping by checking the Machine Check Events (MCE) logs (in /var/log/mcelog).

If a message that is similar to the following and that contains "THERMAL EVENT " is repeatedly logged in 8 lines in /var/log/mcelog at around the time (within 5 minutes) when the message containing "Hardware Error" is

5. Installing Software Components

Express5800/B120e-h User's Guide

100

Chapter 3 Setup

logged in /var/log/messages, the "Hardware Error" is logged by the OS when the OS r eceives a request to perform the power cutting operation, which does not indicate an failure in the server.

Ex.) MCE 0 CPU 23 THERMAL EVENT TSC 3559f8b98fe2 TIME 1331221119 Fri Mar 9 00:38:39 2012 Processor 23 below trip temperature. Throttling disabled STATUS 40000000882e0800 MCGSTATUS 0 MCGCAP 1000c14 APICID f SOCKETID 0 CPUID Vendor Intel Family 6 Model 45 Hardware event. This is not a software error.

It's possible to be to change the power control mode of this prod uct to "Static mode" from "Dynamic mode" of default and reduce the output frequency of the message.

The power control mode is established in the EM card.

■ In the case of SIGMABLADE-M(N8405-016F/016AF/016BF) See the section of "Using Command Line Console Feature" - "Comman d Refere nce" - "s rvp wrmode" in the

User's Guide of the EM card.

■ In the case of SIGMABLADE-Hv2(N8405-040F/040AF) See the section of "Using Command Line Console Feature" - "Command Specification" - "CPU blade

management commands" - "Setting power control mode of CPU blade" and "Displaying power control mode of CPU blade" in the User's Guide of the EM card.

NEC Express5800/B120e-h, N8400-217F, N8400-215F, N8400-216F, N8400-218F User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual