NEC AccuSync LCD22WMGX, AccuSync LCD24WMCX User Manual

AccuSync LCD22WMGX

AccuSync LCD24WMCX

User’s Manual

English

English-1

Declaration

Declaration of the Manufacturer

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.

RISK OF ELECTRIC SHOCK • DO NOT OPEN

As an ENERGY STAR Partner, NEC Display Solutions of America, Inc. has determined that this product meets the ENERGY STAR
guidelines for energy efficiency. ENERGY STAR is a U.S. registered mark. The ENERGY STAR emblem does not represent EPA
endorsement of any product or service.
ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,
Norway, Spain, Sweden, U.K..
IBM PC/XT/AT, PS/2, MCGA, VGA, 8514/A and XGA are registered trademarks of International Business Machines
Corporation.
Apple and Macintosh are registered trademarks of Apple Inc.
Microsoft and Windows are registered trademarks of the Microsoft Corporation.
NEC is a registered trademark of NEC Corporation.
All other trademarks or registered trademarks are property of their respective owners.

We hereby certify that the colour monitors AccuSync
LCD22WMGX (TFT22W90PS)/AccuSync
LCD24WMCX (TFT24W90PS) are in compliance with

Council Directive 73/23/EEC:

– EN 60950-1

Council Directive 89/336/EEC:

– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024

and marked with

NEC Display Solutions, Ltd.

4-13-23, Shibaura,

Minato-Ku

Tokyo 108-0023, Japan

Caution:

When operating the AccuSync LCD22WMGX/AccuSync LCD24WMCX with a 220-240V AC power source in Europe, use the
power cord provided with the monitor.

In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this equipment.
If a power cord is not supplied with this equipment please contact your supplier.

For all other cases, use a power cord that matches the AC voltage of the power outlet and has been approved by and
complies with the safety standard of your particular country.

English-2

For the Customer to use in U.S.A. or Canada

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 60950-1.

Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele Canadiens selon CAN/CSA C22.2 No. 60950-1.

FCC Information

1. Use the attached specified cables with the AccuSync LCD22WMGX/AccuSync LCD24WMCX colour monitor so as not
to interfere with radio and television reception.

(1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,

and meet the following condition.

Power supply cord Non shield type, 3-conductor
Length 1.8 m
Plug shape

U.S.A

(2) Please use the supplied shielded video signal cable and audio cable. Use of other cables and adapters may

cause interference with radio and television reception.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:
“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government
Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.

U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address: 500 Park Blvd, Suite 1100

Itasca, Illinois 60143

Tel. No.: [phone]

Type of Product: Display Monitor

Equipment Classification: Class B Peripheral

Model: AccuSync LCD22WMGX (TFT22W90PS)

AccuSync LCD24WMCX (TFT24W90PS)

We hereby declare that the equipment specified above conforms

to the technical standards as specified in the FCC Rules.

English

English-3

Contents

Your new NEC LCD monitor box* should contain the following:

• LCD monitor with tilt base

• Power Cord

•Video Signal Cable (15-pin mini D-SUB to 15-pin mini D-SUB male)

•Video Signal Cable (DVI-D to DVI-D)

• Audio Cable

• User’s Manual

• CD-ROM

• Base Stand

• Cable Holder

Component Names and Functions

User’s Manual

Power Cord 15-pin mini D-SUB

to 15-pin mini

D-SUB male

LCD monitor

(Stand not connected)

CD-ROMCable Holder

*

Remember to save your original box and packing material to transport or ship the monitor.

Audio Cable

DVI-D to DVI-D

1

2

3

4

5

6

7

Source

Auto

-/<

+/>

Menu

Power Switch

Power LED

Switches the input source being displayed.

When not in OSD menu, enables Auto Configuration.
When in OSD menu, act EXIT-key.

When not in OSD menu, lowers the sound volume.
When in OSD menu, decreases value or move left/up cursor.

When not in OSD menu, raises the sound volume.
When in OSD menu, increases value or move right/down cursor.

Opens or Closes the OSD menu.

Turns on or off the main power.

LED Blue - Power is ON.
LED Amber - Monitor is in “Power Saving Mode”.
LED is off - Power is OFF.

English-4

Quick Start

To attach the Base to the LCD Stand:

1. Insert the front of the LCD stand into the holes in the front of the Base (Figure S.1).

2. Attach the Base to the Stand. The locking tab on the Base should fit into the hole

on the back of the Stand (Figure S.1).

To attach the LCD monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to

the connector of the display card in your system (Figure A.1).

For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable
connected with the monitor to the connector of the display card in your system
(Figure A.2). Tighten all screws.

For the Mac: Connect the MultiSync Macintosh cable adapter (not included) to the
computer. Attach the 15-pin mini D-SUB signal cable to the MultiSync Macintosh cable
adapter (Figure A.3). Tighten all screws.

NOTE: Some Macintosh systems do not require a Macintosh cable adapter.

Figure S.1

Stand

Base

Locking Tabs

Figure A.1 Figure A.3

Macintosh
Cable Adapter
(not included)

Figure A.2

LCD22WMGX LCD24WMCX

1

2

3

4

5

6

7

8

9

10

SPDIF OUT

Component (Audio)

Component (Video)

Headphone Jack

AUDIO IN

D-SUB

DVI-D

HDMI

AC IN

Kensington Lock Opening

Outputs the Digital audio signal from HDMI (COAXIAL).

Connects Component Audio.

Connects Component Video.

Connects headphones to the monitor.

Connects audio input from PC.

Connects to analog RGB input.

Connects to digital RGB input.

Connects to digital HDMI signals.

Connects power cord to monitor.

Monitor can be secured using a Kensington locking system.

English

English-5

3. Connect one end of the power cord to the monitor and the other end to the power outlet. Use the Cable holder to keep the

Video Signal Cable, Audio cable and power cord together (Figure B.1).

4. To attach the Cable Holder:

Attach the Cable Holder on to the Base. Insert the hooks on the Cable Holder into the holes at the back of the Stand and
slide the Cable Holder downward into place (Figure B.1).

NOTE: Please confirm that the tabs are completely secure.

NOTE: Adjust position of cable that place under the Cable holder to avoid damage for cable or monitor.

NOTE: Please refer to Caution section of this manual for proper selection of power cord.

5. Turn on the monitor with the front power button and the computer (Figure C.1).

6. Select input source by Source button or Input Select on OSD menu.

Figure B.1

Cable holder

Figure C.1

Power Button

Input (DVI)

Audio Cable

Input (VGA)

Power Cable

Input (HDMI)

Headphone

7. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings.

For further adjustments, use the following OSD controls:

• Image Setup

Refer to the Controls section of this User’s Manual for a full description of these OSD controls.

NOTE: If you have any problem, please refer to the Troubleshooting section of this User’s Manual.