NCR 7705 R1.1 EBox Kit Instructions

Kit Instructions

7705 R1.1 EBox

7705-K036
Issue A

The product described in this book is a licensed product of NCR Corporation.

NCR is a registered trademark of NCR Corporation. NCR SelfServ™ is a trademark of NCR Corporation
in the United States and/or other countries. Other product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.

It is the policy of NCR Corporation (NCR) to improve products as new technology, components,
software, and firmware become available. NCR, therefore, reserves the right to change specifications
without prior notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this
document, consult with your NCR representative or NCR office for information that is applicable and
current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity,
organization, and value of this book. Please use the link below to send your comments.

EMail: [e-mail]

Copyright © 2017
By NCR Corporation
Duluth, GA U.S.A.
All Rights Reserved

Revision Record

Issue Date Remarks

A

July 2017 First Issue

7705 R1.1 EBOx

Introduction

This kit provides components to upgrade the 7705 EBox into an NCR"XR6"
Motherboard which is based on Intel's Shark Bay Platform (Intel Haswell 22nm
processor with Lynx Point Q87 Chipset). The EBox also provides the following
components:

• Intel Core i3-4350T, 3.1 GHz processor

• 4GB, 1600MHz memory module

• 500GB HDD

1-2 7705 R1.1 EBOx

Kit Contents

7705 R1.1 EBOx 1-3

Installation Procedure

Warning: Disconnect the AC power cord before disassembling the Terminal.

Caution: Static Electricity Discharge may permanently damage your system. Discharge

any static electricity build up in your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and handle cards only by their external
edges.

Caution: Properly hold and support the EBox assembly while loosening and tightening
the screws securing the assembly to the fascia.

Perform the following procedures to install the 7705 R1.1 EBox:

1. Removing the Existing EBox Assembly

2. Installing the 7705 R1.1 EBox

1-4 7705 R1.1 EBOx

Removing the Existing EBox Assembly

1. Shut down the Kiosk Operating System and turn off the Kiosk.

2. Unplug the terminal’s power cord.

3. Open the Kiosk Fascia using a key to access the EBox.

4. Take note of all cables connected to the EBox and the cable routing. Disconnect all
the cables and remove them from the cable strain relief. Remove cable ties as
necessary.

5. Disconnect the DVIcable from the Display and remove the cable from the Fascia.
This cable will be replaced with the HDMI to DVI cable included in this kit.

7705 R1.1 EBOx 1-5

6. Loosen the screws (4) securing the EBox assembly to the fascia then slide the EBox
assembly upwards to remove the assembly.

7. Remove the screws (2) securing the EBox Mini DCHub then remove the Mini
DCHub.

1-6 7705 R1.1 EBOx

8. Remove the screws (2) on each side securing the EBox to the brackets and slide the
EBox upwards to remove it..

7705 R1.1 EBOx 1-7

Installing the 7705 R1.1 EBox

1. Mount and secure the R1.1 EBox to the bracket assembly using screws (2 on each
bracket).

2. Mount and partially tighten screws (2) on the EBox for the Mini DCHub assembly.

1-8 7705 R1.1 EBOx

3. Slide the Mini DC Hub on the screws then fully tighten the screws (2) to secure the
Mini DCHub.

7705 R1.1 EBOx 1-9

4. Mount and secure the EBox assembly to the Fascia.

a. Align and insert the slots of the Ebox brackets to the mounting screws positioned

on the display lower bracket.

b. Insert the mounting keyholes of the EBox brackets through the mounting screws

positioned on the display top bracket.

c. Slide the Ebox Assembly downward and tighten the four mounting screws to

secure the Ebox assembly.

1-10 7705 R1.1 EBOx

5. Connect the DVIconnector of the HDMI to DVIcable to the Display and connect
the HDMI connector to the EBox IOPanel.

7705 R1.1 EBOx 1-11

6. Connect the Fascia Harness Cables to the Ebox and DC Hub.

a. Plug the DVD-RW cable to the eSATA connector on the side of the EBox.

b. Plug the following DC cables to the Mini DC hub on the side of the EBox:

• Touchscreen

• EBox

• Mini DC Hub cable from top box

c. Plug the cables in the table below to the EBox I/O Panel:

Note: Some device cables may not be present depending on the Kiosk configuration.

EBOXI/OPanel Cable

USB3.0 Ports 19-inch Touchscreen

USBMini Hub (from top Box USBMini Hub)

LAN LAN

RS 232 (COM 1) Note Acceptor

USB1 PINPads (IPP350, VX805/820) or UX300 MSR

USB 2 Barcode Scanner

USB 3 USBCamera Digitizer

USB4 Trackball and Switch

Audio Out Line Out (from MIDIMISC IF)

DCPower DC distribution (from EBox Mini DChub)

1-12 7705 R1.1 EBOx

7. Tidy up and secure the cables using cable ties and the cable strain relief bracket.