NCR 7702 K460 Kit Instructions

Kit Instructions

High Mount 2x20 Customer Display

7702-K460
Issue C

The product described in this book is a licensed product of NCR Corporation.

NCR is a registered trademark of NCR Corporation. NCR RealPOS is a trademark of NCR Corporation in
the United States and/or other countries. Other product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.

It is the policy of NCR Corporation (NCR) to improve products as new technology, components,
software, and firmware become available. NCR, therefore, reserves the right to change specifications
without prior notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this
document, consult with your NCR representative or NCR office for information that is applicable and
current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity,
organization, and value of this book. Please use the link below to send your comments.

EMail:[e-mail]

Copyright © 2017–2019
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved

Revision Record

Issue Date Remarks

A

B

Aug 2017 First Issue

Sept 2017 V002 - Added serial expansion housing

C

Apr 2019 Added 006-8622686

High Mount 2x20 Customer Display

This kit contains the components to add a High Mount 2x20 Customer Display to any of
the following terminals:

• NCR XR5POS (7701)

• NCR XR7POS (7702)

• NCR XR7 PlusPOS (7703)

Kit Contents

2 High Mount 2x20 Customer Display

Installation Procedure

1. Remove the Stand.

a. Lay the terminal face down on a flat surface.

Caution: Always use a soft material (cloth, foam) to protect the display screen when
placing the terminal face down.

b. Remove the two (2) captive screws that secure the Stand to the terminal.

c. Rotate the Stand away from the Back Housing as shown below to unhook the

tabs..

High Mount 2x20 Customer Display 3

2. Remove the existing Serial Expansion Housing.

a. Remove the Serial Expansion Module from the Stand (3 screws).

b. Remove the four (4) screws securing the Serial Expansion Board to theSerial

Expansion Housing.

c. Remove the Serial Expansion Board from the Serial Expansion Housing.

4 High Mount 2x20 Customer Display

3. Install the new Serial Expansion Housing included in the kit.

a. Route the cable through the opening of the new Serial Expansion Housing (497-

0514376).

b. Mount the Serial Expansion Board on the Serial Expansion Housing. Ensure the

Cable Grommet is mounted on the grommet guide of the Serial Expansion
Housing.

c. Secure the Serial Expansion Board to the new Serial Expansion Housing (4

screws).

High Mount 2x20 Customer Display 5

d. Install the Serial Expansion Module to the Stand (3 screws).

4. Reinstall the Stand.

a. Insert the Serial Expansion Housing Tabs into the openings in the Back Housing

and rotate the Stand downward.

6 High Mount 2x20 Customer Display

b. Secure the stand to the terminal using two (2) captive screws.

5. Install the High Mount 2x20 Customer Display.

a. Mount the Cable Strain Relief to the Cable Management Bracket.

High Mount 2x20 Customer Display 7

b. Connect the USB Cable to the Customer Display. Note the cable routing (Cable

Management Bracket removed for clarity).

c. Insert the tab on the edge of the Cable Management Bracket into the slot in the

Rear Cover of the Customer Display.

8 High Mount 2x20 Customer Display

d. Pivot the Cable Management Bracket until it snaps into position.

e. Route the Cable through the top opening of the Mounting Bracket.

High Mount 2x20 Customer Display 9

f. Attach the Mounting Bracket to theCustomer Display using three (3)screws.

g. Route the Cable as shown.

10 High Mount 2x20 Customer Display

h. Slide the Customer Display and Mounting Bracket Assembly over the Serial

Expansion Housing of the terminal.

i. Secure the Assembly to the terminal using four (4) screws.

j. Pivot the terminal and open the cable cover.

High Mount 2x20 Customer Display 11

k. Connect the USB Cable to any available +12V USB Port on the terminal.

12