National Semiconductor DS90C363A, DS90CF363A Technical data

查询DS90C363A供应商

DS90C363A/DS90CF363A
+3.3V Programmable LVDS Transmitter 18-Bit Flat Panel
Display (FPD) Link-65 MHz
+3.3V LVDS Transmitter 18-Bit Flat Panel Display (FPD)
Link-65 MHz

June 1998

DS90C363A/DS90CF363A +3.3V Programmable LVDS Transmitter 18-Bit Flat Panel Display (FPD)

Link-65 MHz, +3.3V LVDS Transmitter 18-Bit Flat Panel Display (FPD)Link-65 MHz

General Description

The DS90C363A/DS90CF363A transmitter converts 21 bits
of CMOS/TTLdata intothree LVDS (LowVoltage Differential
Signaling) data streams. A phase-locked transmit clock is
transmitted in parallel with the data streams over a fourth
LVDS link. Every cycle of the transmit clock 21 bits of input
data are sampled and transmitted. At a transmit clock fre­quency of 65 MHz, 18 bits of RGB data and 3 bits of LCD
timing and control data (FPLINE, FPFRAME, DRDY) are
transmitted at a rate of 455 Mbps per LVDS data channel.
Using a 65 MHz clock, the data throughput is 170 Mbytes/
sec. The DS90C363A transmitter can be programmed for
Rising edge strobe or Falling edge strobe through a dedi­cated pin. The DS90CF363A is fixed as a Falling edge
strobe transmitter. A Rising edge or Falling edge strobe
transmitter will interoperate with a Falling edge strobe Re­ceiver (DS90CF364) without any translation logic.

This chipset is an ideal means to solve EMI and cable size
problems associated with wide, high speed TTL interfaces.

Block Diagrams

DS90C363A/DS90CF363A

Features

n 20 to 65 MHz shift clock support
n Rejects

n Best–in–Class Set & Hold Times on TxINPUTs
n Tx power consumption

n

n Tx Power-down mode
n ESD rating
n Supports VGA, SVGA, XGA and Dual Pixel SXGA.
n Narrow bus reduces cable size and cost
n Up to 1.3 Gbps throughput
n Up to 170 Megabytes/sec bandwidth
n 345 mV (typ) swing LVDS devices for low EMI
n PLL requires no external components
n Compatible with TIA/EIA-644 LVDS standard
n Low profile 48-lead TSSOP package
n Improved replacement for:

>

±

3ns Jitter from VGA chip with less than

225ps output Jitter

Grayscale

>

50%Less Power Dissipation than BiCMOS

Alternatives

SN75LVDS85 — DS90C363A
SN75LVDS84 — DS90CF363A

@

65MHz (TJCC)

<

130 mW (typ)@65MHz

<

>

7 kV (HBM),>500V (EIAJ)

200µW (max)

DS100138-1

Order Number DS90C363AMTD or DS90CF363AMTD

TRI-STATE®is a registered trademark of National Semiconductor Corporation.

© 1998 National Semiconductor Corporation DS100138 www.national.com

See NS Package Number MTD48

Absolute Maximum Ratings (Note 1)

If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/

ESD Rating

(HBM, 1.5 kΩ, 100 pF)

(EIAJ, 0Ω, 200 pF)

>

>

7kV

500V

Distributors for availability and specifications.

Supply Voltage (V
CMOS/TTL Input Voltage −0.3V to (V
LVDS Driver Output Voltage −0.3V to (V
LVDS Output Short Circuit

Duration Continuous

) −0.3V to +4V

CC

CC
CC

+ 0.3V)
+ 0.3V)

Junction Temperature +150˚C
Storage Temperature −65˚C to +150˚C
Lead Temperature

(Soldering, 4 sec) +260˚C

Maximum Package Power Dissipation Capacity

MTD48 (TSSOP) Package:

DS90C363A/DS90CF363A 1.98 W

Package Derating:

DS90C363A/DS90CF363A 16 mW/˚C above +25˚C

@

25˚C

Recommended Operating
Conditions

Supply Voltage (V

) 3.0 3.3 3.6 V

CC

Operating Free Air

Temperature (T

) −10 +25 +70 ˚C

A

Receiver Input Range 0 2.4 V
Supply Noise Voltage (V
TxCLKIN frequency 18 68 MHz

Min Nom Max Units

) 100 mV

CC

PP

Electrical Characteristics

Over recommended operating supply and temperature ranges unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units

CMOS/TTL DC SPECIFICATIONS

V

IH

V

IL

V

CL

I

IN

LVDS DC SPECIFICATIONS

V

OD

∆V

V

OS

∆V

I

OS

I

OZ

TRANSMITTER SUPPLY CURRENT

ICCTW Transmitter Supply Current

ICCTG Transmitter Supply Current

ICCTZ Transmitter Supply Current

Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits. The tables of “Electrical Characteristics” specify conditions for device operation.

Note 2: Typical values are given for V
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground unless otherwise speci-

fied (except V
Note 4: V

High Level Input Voltage 2.0 V
Low Level Input Voltage GND 0.8 V
Input Clamp Voltage ICL= −18 mA −0.79 −1.5 V
Input Current VIN= 0.4V, 2.5V or V

V

= GND −10 0 µA

IN

CC

+1.8 +10 µA

Differential Output Voltage RL= 100Ω 250 345 450 mV
Change in VODbetween

OD

complimentary output states
Offset Voltage (Note 4) 1.125 1.25 1.375 V
Change in VOSbetween

OS

complimentary output states
Output Short Circuit Current V
Output TRI-STATE®Current Power Down = 0V,

Worst Case

16 Grayscale

Power Down

= 0V, RL= 100Ω −3.5 −5 mA

OUT

V

=0VorV

OUT

R

= 100Ω,

L

= 5 pF,

C

L

Worst Case Pattern

CC

(Figures 1, 4)

R

= 100Ω,

L

= 5 pF,

C

L

16 Grayscale Pattern

(Figures 2, 4)

Power Down = Low

f = 32.5 MHz 31 43 mA
f = 37.5 MHz 33 45 mA
f = 65 MHz 39 52 mA
f = 32.5 MHz 23 35 mA
f = 37.5 MHz 28 40 mA
f = 65 MHz 33 45 mA

±

1

10 55 µA
Driver Outputs in TRI-STATE®under
Power Down Mode

= 3.3V and TA= +25C.

CC

and ∆VOD).

OD

previously referred as VCM.

OS

CC

35 mV

35 mV

±

10 µA

V

www.national.com 2

Recommended Transmitter Input Characteristics

Over recommended operating supply and temperature ranges unless otherwise specified

Symbol Parameter Min Typ Max Units

TCIT TxCLK IN Transition Time
TCIP TxCLK IN Period
TCIH TxCLK IN High Time
TCIL TxCLK IN Low Time

(Figure 6 )

(Figure 6 )

(Figure 6 )

(Figure 5 )

14.7 T 55.6 ns

0.35T 0.5T 0.65T ns

0.35T 0.5T 0.65T ns

5ns

Transmitter Switching Characteristics

Over recommended operating supply and temperature ranges unless otherwise specified

Symbol Parameter Min Typ Max Units

LLHT LVDS Low-to-High Transition Time
LHLT LVDS High-to-Low Transition Time
TPPos0 Transmitter Output Pulse Position for Bit 0
TPPos1 Transmitter Output Pulse Position for Bit 1 1.90 2.20 2.40 ns
TPPos2 Transmitter Output Pulse Position for Bit 2 4.10 4.40 4.60 ns
TPPos3 Transmitter Output Pulse Position for Bit 3 6.30 6.60 6.80 ns
TPPos4 Transmitter Output Pulse Position for Bit 4 8.50 8.80 9.00 ns
TPPos5 Transmitter Output Pulse Position for Bit 5 10.70 11.00 11.20 ns
TPPos6 Transmitter Output Pulse Position for Bit 6 12.90 13.20 13.40 ns
TPPos0 Transmitter Output Pulse Position for Bit 0
TPPos1 Transmitter Output Pulse Position for Bit 1 3.22 3.57 3.92 ns
TPPos2 Transmitter Output Pulse Position for Bit 2 6.79 7.14 7.49 ns
TPPos3 Transmitter Output Pulse Position for Bit 3 10.36 10.71 11.06 ns
TPPos4 Transmitter Output Pulse Position for Bit 4 13.93 14.28 14.63 ns
TPPos5 Transmitter Output Pulse Position for Bit 5 17.51 17.86 18.21 ns
TPPos6 Transmitter Output Pulse Position for Bit 6 21.08 21.43 21.78 ns
TPPos0 Transmitter Output Pulse Position for Bit 0
TPPos1 Transmitter Output Pulse Position for Bit 1 4.00 4.40 4.80 ns
TPPos2 Transmitter Output Pulse Position for Bit 2 8.40 8.80 9.20 ns
TPPos3 Transmitter Output Pulse Position for Bit 3 12.80 13.20 13.60 ns
TPPos4 Transmitter Output Pulse Position for Bit 4 17.20 17.60 18.00 ns
TPPos5 Transmitter Output Pulse Position for Bit 5 21.60 22.00 22.40 ns
TPPos6 Transmitter Output Pulse Position for Bit 6 26.00 26.40 26.80 ns
TSTC TxIN Setup to TxCLK IN
THTC TxIN Hold to TxCLK IN
TCCD TxCLK IN to TxCLK OUT Delay

TxCLK IN to TxCLK OUT Delay

TJCC Transmitter Jitter Cycle-to-Cycle

TPLLS Transmitter Phase Lock Loop Set
TPDD Transmitter Power Down Delay

Note 5: The Minimum and Maximum Limits are based on statistical analysis of the device performance over process, voltage, and temperature ranges. This param­eter is functionality tested only on Automatic Test Equipment (ATE).

Note 6: The Limits are based on statistical analysis of the device performance over process, voltage, and temperature ranges. Output jitter is measured with a cycle­to-cycle jitter of 3ns applied to the input clock signal. A jitter event of 3ns, represents worse case jump in the clock edge from most Graphics controller VGA chips
currently available. This parameter is used when calculating system margin (RSKM). See Figures 12, 13 and AN-1059.

(Figure 6 )

(Figure 6 )

(Figure 4 )
(Figure 4 )

(Figure 11 )

(Figure 11 )

(Figure 11 )

(Figure 7 )

TA=25˚C, VCC=3.3V 3 5.5 ns

(Figure 7 )

(Figures 12, 13 )

(Figure 8 )

(Figure 10 )

(Note 5) f=65 MHz −0.30 0 0.20 ns

(Note 5) f=40 MHz −0.35 0 0.35 ns

(Note 5) f=32.5

MHz

(Note 6) f=65 MHz 175 225 ps

f=40 MHz 240 380 ps

f=32.5

MHz

0.75 1.5 ns

0.75 1.5 ns

−0.40 0 0.40 ns

2.5 ns
0ns

3 7.0 ns

260 400 ps

10 ms

100 ns

www.national.com3