Nascom N135WGG-SW-CAPC, N135WGW-SW-CAPC, N135WGW-ST-CAPC, N135WGT-SW-CAPC, N135WGT-ST-CAPC Specsheet
...
N135WG CAP C
STICK ON CAPSULE SWITCH AND MAGNET SET WITH CENTER LEADS
DESCRIPTION
Nascom’s N135WG CAP C Series is our ground breaking CAP switch. Never
drill in windows or doors again. The switch and magnet are so thin they will
t between the window sill and sash. When surface mounted, the smooth
rounded edges and ultra-thin prole makes it almost disappear. The CAP
switch is designed to protect all nonferrous (e.g. wood, aluminum and vinyl)
doors and windows, in both residential and commercial settings.
The N135WG CAP C, is the installer’s choice of contact conguration where
surface mount is required excellent air and side-to-side gaps are required to
prevent false alarms caused by shifting or warping doors and windows.
FEATURES
• EURO DESIGN - ALMOST DISAPPEARS • 3M VHB (Very High Bond) DOUBLE SIDED TAPE
• 12” 24AWG ZIPCORD LEADS • ABS HOUSINGS
• WIDE GAP - N35 NdFeB RARE EARTH
ORDERING INFORMATION
CONTACT RATING
PART
NUMBER
COLOR
OPERATE
GAP
(in inches)
(Max DC/Peak AC Resistive)
SWITCHING CARRY
V I V I
CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:
N135WGB/ST CAPC
N135WGG/ST CAPC
N135WGT/ST CAPC
N135WGW/ST CAPC
BROWN
GREY
TAN
WHITE
0.50 to 0.875 200 VDC 0.5 Amps 10vA 1.5 Amps 150 mOhms
STATIC
CONTACT
RESISTANCE
(50mV, 100mA)
WIRING SCHEMATIC
SWITCH
CONTACT
CLOSED LOOP,
NORMALLY OPEN CONTACT
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
|
F: 800.727.4041
|
www.nascominc.com
DWG No. 131123-17 Rev. 1
1
.275
6.99
.168
4.25
3M VHB TAPE
.335
8.51
11.00
279.40
DIMENSIONS - IN [mm]
.015
0.38
.168
4.25
3M VHB TAPE
N135WG CAP C
STICK ON CAPSULE SWITCH AND MAGNET SET WITH CENTER LEADS
STICK ON CAPSULE SWITCH AND MAGNET SET WITH CENTER LEADS
SWITCH
MAGNET
INSTALLATION INSTRUCTIONS
• Pre-t the switch and magnet in the desired location on the window.
• Clean the mounting surface area for both switch and magnet with alcohol and let dry.
• Remove the liner from the tape on the back of the switch and carefully position the switch on the window frame as close
as possible to the movable part of the window.
• Remove the liner from the tape on the back of the magnet and carefully align the magnet parallel with the switch on the
movable part of the window and as close to the window frame as possible.
• Apply rm pressure to the switch and magnet housing to ensure proper adhesion to the mounting surface.
• Connect the switch leads to the alarm system circuit. Caution! Hold wire leads, not the switch housing while cutting and
stripping to prevent damage to switch.
• Test alarm system for correct operation.
PART NUMBERING SYSTEM
COLOR:
• B = BROWN
• G = GREY
• T = TAN
• W = WHITE
N135WG
X ST/ XXXX
CAPC
LEAD LENGTH (zero, 3 or 4 digits):
• Blank - 12 Inches
• All other lengths specied in Inches with 3
digits (e.g. 036 = 36 Inches)
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
|
F: 800.727.4041
|
www.nascominc.com
DWG No. 131123-17 Rev. 1
2
Loading...