MyWeigh iBALANCE 201 User Manual

SPECIFICATIONS

Model number i201 Capacity 100g Division 0.005g

Platte r / Tray
N et/gross weight 510/620g

Package

Standard carton: 29×22×14(cm3)

12 Units in one box: 60×45×45(cm

Operating Temperature

6×AA Size Batteries or AC/AC

Power source

Adapter 11V/150mA (optional)

**SPECIAL WARNING**

Cell-Phones, Cordless-Phones, and any radio-frequency device can

cause temporary interference and cause the scale to temporarily not

work properly. Please do not use any electronic device near the i101.

Just like in an Airplane, do not use your cell-phone near the scale

when it is in use. While there is NO risk of permanent damage to

the scale, interference can cause an incorrect calibration or incorrect

weight readings.

φ100mm

0-40c (32-104℉))

3

)

i201 COMPACT SCALE

My Weigh iBalance SERIES

i201 Generation 3

INSTRUCTION MANUAL

SAFETY PRECAUTIONS

All saf ety messages are identi fied by t he words "WARNING" and "CAUTION".

These words mean the following:

△!WARNING

△!CAUTION

When using the i201, the following safety precautions should always be followed.

Use only the c orrect AC adaptor with t he sc ale. Oth er ad aptors m ay c ause

permanent electrical damage.

Avoid placing the s cale in d irect sunlight, this may cause discolora tion or
malfunction.

Replace all batteries at the same ti me – D o not re place only a portion of the 6
batteries as this may cause a malfunction.

If the scale is not to be used for a long period of time, remove all batteries from the
battery compartment to avoid leakage, which may cause damage to this scale.

Avoid overloading th e scale, as t his may cause perm anent da mage a nd void
your warranty – do not EVER put more then 100 grams on the scale.

Keep the scale away fr om water – this scal e is not water r esistant. Shock, injury
and electrical damage can occur if used in a wet location!

Matter charged w ith static electricity c ould affect accura cy. Dischar ge all static
electricity. For ex ample, one method is to use Static-Guard spray, and spray it o n
both sides of the weighing platform.

Important i nformation to a lert you to a
situation that might cause serious injury and
damage to y our pr operty if instru ctions ar e
not followed.

Important information that tells how to pr event
damage to the equipment.

!

W ARNING

△

!

CA UTION

△

1

Counting procedures

1.Press [ON/OFF] to turn on the scale.

Wait for "0" to appear on the display.

2.Start the Count Procedure
If necessary, press [ZERO] key to set the display to “0”.

3. Place a given number of samples of an item on the pan (the Sample Size should

be either 10、20、50 or 100 pieces). The weight of these samples will show on the
display.

4. Press the [UNIT] key several times to put the sca le in PCS mode (the indicator
should be on pcs).

5. Select the s ample size (the same as you chose above) by pressing the [PCS] key
(press it as many times as necessary to put it in the correct sample size (the sample
size is the same as in step three =10、20、50or100),

6. P ress the [UNIT] key , the displa y will show “pass”, then after 2 seconds, the
scale will remember the sample size you selected and show the starting sample size
on the display
(you can now remove the samples if you want to return the scale to 0)

7. Place the items that you want counted onto the tray and the total number of items
will show on the display.

8. Pr ess the “UN IT” key to e xit the counting f unction a nd return to normal
weighing or you can press ON/OFF to turn the scale off .
NOTE: the weight of unit sample > 10e.

FUNCTION SETTINGS

1. Enter function setting mode.

The sc ale sho uld be OFF . Press a nd hold [UNIT] first, then p ress and
release [ON/OFF] ( while keeping [UNIT] pre ssed) the display will show
LIGHT or A_OFF ar row and the disp lay will sh ow 888888 Now you can
release the UNIT key.

2. Selection of auto backlight mode.

Press [UNIT] to select auto backlight function, the display will show an arrow
next to LIGHT , this means auto ba cklight f unction activ e, press [UNIT]
again, the display will not show the arrow next to LIGHT, this means the auto
backlight function is inactive, i.e. shut off backlight function.

3. Selection of auto shut off mode.

Press [ZERO] to select auto shut off function, the disp lay will show an arrow
next to A_OFF, this means auto shut off function active. Press [ZERO] again,
the displa y will not show a n arrow next to A_OFF, this means the auto shut
off function is inactive.

4. Return to weighing mode.

Press [ON/OFF] to tu rn the power off, press [ON/OFF] again to turn on the

power and the scale will return to normal weighing mode.

6