Muse M-752 DR user Manual

M-752DR

User Manual

CAR RADIO DVD PLAYER

Please read the instruction carefully

before operating the unit.

English

BEFORE YOU BEGIN

Important safeguards

Be sure to connect the color coded leads according to the diagram. Incorrect

1.
connections may cause the unit to malfunction or damage the vehicle’s elec-

trical system.
Be sure to connect the speaker (-) leads to the speaker (-) terminal. Never

2.
connect the left and right channel speaker cables each other or to the vehicle
body.

Make sure all the connections are completely correct before turning on your

3.
unit.

When replacing the fuse(s), the replacement must be of the same amperage

4.
as shown on the fuse holder.

Do not block vents or radiator panels. Blocking them will cause heat to build

5.
up inside and may result in fire.

After completing the installation and beginning to play the unit(including re-

6.
placing the battery), press RESET button on the base with pointed object

(such as ball-point pen) to set the unit to initial status.
Do not attempt to modify the unit, modifying the unit may cause an accident.

7.
Stop the vehicle before carrying out any operation that could interfere with

8.
your driving.

Do not work in extremely high or low temperature. Be sure the temperature

9.
inside the vehicle is between +60°C and -10°C before turning on your unit.

T o avoid the driver distract his attention from, please install the unit in an apt

10.
place.

Using the unit after starting the engine, otherwise the unit can not be started,

11.
because the electric energy of battery was used up.

Do not use the unit in extreme high temperature or such low temperature

12.
conditions, and also avoid humidity and direct sunlight, otherwise the electric

energy of battery will be wasting for the high temperature.
T ake care of the magnetism of the unit. Do no put the credit card, cassette or

13.
watch around the unit, otherwise they would be broken or some information in
them loses.

To avoid disturbing the video frequency, keep far away from the unit when

14.
using your phone.

Do not put the remote control under high temperature or where the sun strikes

15.
it, or else the remote control can not work normally.

Be sure to remove the transportation screw absolutely before mount-

16.

ing the unit.

Please warn children not to play the motorized screen which might hurt their

17.
fingers.

GB - 1

When you select or create a disc to play with this product, please note:

Avoid long file names! It is suggested to name the file with no much than 14
characters.
The total number of files on the disc should not exceed 3000. But under a table
of contents most demonstrates 646 documents.
The maximum number of directories should not exceed 299.
The maximum depth level of directories should not exceed 37.
File system(SD & USB): FAT 32 and FA T 16.

Disc and files you can play

In spite of progress made to ensure playability of all discs types, it is not possible
to guarantee playback of discs which are not in conformity with DVD, CD, VCD
or SVCD standards.
This unit may not play some recordings or files on CDs or DVDs due to differ­ences in recording formats, software used and disc types. The recordable discs
may need a longer reading time than normal discs.

GB - 2

INSTALLATION

Wiring Connection

1) Output Plug(Male)

2) Output Socket
(Female)

3) Fan window

Note:

The brown wire (Parking Break) is connected with brake signal; for safety,
the programs can be seen on the monitor after braking the car, but RCA
output are free of it.
If you do not want to use this function, connect it with the negative pole.

GB - 3 GB - 4

Install the unit
Note: Regardless of the type of installation used, remove the car radio from the

mounting sleeve (cf. "Detach the unit") before starting installation.

Installation Method 1:

DIN Front - Mount

Installation Method 2

Installation using the screw holes at the sides of the
unit. Select a position where the screw holes of the
mounting bracket supplied with the car and the screw
holes of the main unit become aligned (are fitted), and
tighten the screws (see at 2 places on each side). And
then fasten them to the car.

Detach the unit

Detach the front panel before disassembling the unit.

1. Take out the Outer Trim Frame 5 .

2. Insert the keys 6 supplied to the unit at both sides of the unit (shown as
illustrated) until they click. Pulling the keys makes it possible to remove the
unit from the dashboard.

LOCATION OF THE CONTROLS

1.

SRC/PWR Button

2.

BAND/+(Bands selector/

Front panel

increase) Button

3.

MUTE/-(Mute/decrease) Button

4.

Remote Infrared Sensor

5.

SEL/MENU Button

6.

VOL+/- Button

7.

REL (Release) Button

8.

RES (Reset) Button

9.

(Eject) Button

10.

Disc Loading Slot

11.

SD Card Slot

12.

TFT Display

Base

GB - 5

Remote control

SOURCE/PWR

H1.

GOTO (playing time/track)

H2.

BAND/TITLE

H3.

AMS/MENU

H4.

LOC/SUB-T

H5.

ST/AUDIO

H6.

PTY/ANGLE

H7.

OSD

H8.

ZOOM

H9.

(Slow Forward/Reward)

H10.

P/N (System Adjusting)

H11.

Mute

H12.

PROG(Program playing)

H13.

VOL+/VOL-/SEL (V olume adjust / sound

H14.

characteristics setup)
RPT(Repeat Playing)

H15.

RDM (Playing Tracks at Random)

H16.

(Pause/Play)

H17.

(Stop Playing)

H18.

SETUP

H19.

/ (F.R/F.F); / (Previous/Next Track);

H20.

/ / / / ENTER (Left/Right/Up/Down/ENTER)

AF/EQ(alternative frequency/equalizer)

H21.

CLEAR

H22.

0~9( Number) Buttons

H23.

(Eject Button)

H24.

TA/LOUD(traf fic alarm/loudness)

H25.

GB - 6

Replacing battery for the remote control

1. Press the stopper and pull out the battery holder.

2. Install 1pc “CR2025” lithium battery according to the polarity diagram on the
battery compartment.

3. Insert the battery holder into the remote control.

Warning on batteries

• Never recharge the batteries, apply heat to them or take them apart.

• In order to avoid any risk of explosion, observe the polarities indicated inside the
battery compartment.

• Replace only with the type of batteries specified above.

• If you are not using the remote control for a long period of time, remove the
batteries.

• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

• T o prevent short circuit, do not use metal tweezer to clip the battery.

• Attention should be drawn to the environmental aspects of battery disposal.

Before throwing any batteries away, consult your distributor who may be
able to take them back for specific recycling.

BASIC OPERATION

Regional Coding

Y our DVD player has been designed to process regional management informa­tion that is stored on DVD discs. DVD discs that have different regional codes to
that of your player cannot be played. The regional code for your player is 2 (Europe,
the Middle East, South Africa, Japan). ALL means all regions. When you buy a
disc check that it bears the correct logo.

Turning ON/OFF The Unit

Press PWR button (1/H1)) to turn on the unit. When insert a disc, the unit will
automatically start playing. Press and hold PWR button (1/H1) to turn off the
unit.

GB - 7

Selecting Source

Press SRC (1/H1) or BACK in the monitor, enter source menu and press to
select.

• If the font displays in cyan, that means this function is not available.

• Press SRC (1/H1) to switch between play modes. When disc, SD card and
USB were inserted into, press this key again and again to switch among AUX,
Radio, USB, SD card and disc.

Reset the Unit

Operating the unit for the first time or after replacing the car battery, you must
reset the unit.
Press RES button on the unit with a pointed object, (with such as a ball point
pen) to set the unit to initial status.
Note:

• When some errors occur in the display, you can also press RES button to
resume to normal, and it will erase the clock setting power and some memorized
functions.

• This unit will return to standby mode after press RES. Press PWR to power on
the unit again.

Volume Adjusting
T o increase or decrease the sound level, press VOL+/- button (6/H14).

Mute Button

Press MUTE button (3/H12) to shut off the sound. Press it again to resume to
previous volume.
Press and hold MUTE button(3) to enter the night mode, press and hold it again
to switch to normal mode.

Sound Characteristics Setting

Repeatedly press SEL button (5/H14) to select the desired mode in the following
order: VOL (volume) ->BAL (balance) ->F AD (fade) ->BAS (bass) ->TRE (treble)

-> SUB (subwoofer).
After selecting the desired mode, you can adjust the current level by pressing
VOL+/- button (6/H14).
Note: The unit will return to the previous mode if no adjusting about 5 seconds.

EQ Setting

When you are listening to popular music, classic music or rock music, using EQ
function(H21) to select relative status can adjust the sound quality perfectly.
Repeatedly press and hold EQ button (H21), status switches in the following
order: Pop-> Classic-> Rock-> EQ OFF.

Switching Loudness On/off

Press and hold LOUD button (H25) to activate LOUD function. By this function,
you can increase the low frequency, which can improve sensitivity for your ears.
Press and hold this button again to cancel “LOUD” function.

Insert and Eject a Disc

Press REL(7) when the unit is on, Insert a disc (with label side up) into the Disc
Loading Slot (10) when the TFT slanted. T o eject a disc, press (9) on the head
unit will return to the initial status.

• If a disc is locked and can’t be ejected, switch to radio mode then press button

(9) for 3 seconds, the disc can be forced out.

Monitor Angle Setting

Press and hold REL (7) till ANGLE appears in the monitor, press + (2) to adjust
monitor backward, or press - (3) to adjust it forward.
Warning: Do not use outside force to bear on monitor to adjust its angel, other­wise it may destroy the monitor.

PLAYBACK

Play/Pause/Stop

1. Insert a disc, the unit will automatically switch to disc play mode.

2. During playback, press (H17) to pause playback, press again to resume.

• When playing a disc/SD includes PIC file, press (H18) and then / on the

monitor to select the option, press ENTER to play.

3. Press (H18) to stop playback.

• When playing MP4 (DivX, MPEG-4), press (H18) to stop playing, then press

(H17) to return to the beginning of the current track.

• When playing a DVD/VCD disc, press (H18) once to pre-stop,and press

(H20) or (H17) to resume playback. T o quit playing completely press (H18)
twice.

• When driving, cannot look at the video and the pictures, a warning would

be display on screen.
Selecting Folders and Files

In stop mode, press or to select the desire folder or file. Press or
ENTER to enter folder or start playing files.

Note:Press to return previous directory.

Selecting Tracks Fast

1. During CD playback, press to return to the beginning of the current track,
press again within 3 seconds to play previous track; press to play next
track.

2. Press one of Number Buttons (H23) to select a track, it will be played
automatically.
Note: Press within 3 seconds to go to previous track, if the track runs more
than 3 seconds, press to replay current track.

3. During CD/MP3/SD/USB playback, press track region and the screen shows
the following menu: number keys appears, touch the number to select tracks.
Touch the “ X “ to exit this menu.

• To clear the wrongly input, press CLEAR (H22).

4. During DVD/VCD/MP4 playback, touch the screen, the bottom shows the
following menu:

In above menu, press the right half area(except for Track region mentioned above)
of the screen repeatedly to play the next track( shows), or press the left half
area(except for Track region) of the screen to play the previous track( shows).

Repeat playback

For VCD/CD/MP4/SD, press RPT button (H15) to replay the current track. Press
this button again to cancel this function.
For DVD, repeatedly press RPT button (H15) to replay as following: Chapter->
Title->Off.

Note: For Disc (CD/VCD), default setting is Disc repeat. For MP3/WMA,
default setting is folder repeat. For DVD, default setting is whole disc
repeat, but if it stops at a program menu, please select a program and
press ENTER.

Playing tracks in random order

During VCD/CD/MP3/SD/MPEG-4 playback: press RDM button (H16), the unit
plays any track at random under the directory which you select. Press RDM
(H16) again to return to normally playing.

Program playing

VCD/CD: Press PROG button (H13), the TFT displays (12) the program menu.
Press 0~9 number button (H23) to select the track number (for example “05”).
Follow this step repeatedly until the program is finish. Press direction keys (H20)
to move the cursor to START, press ENTER (H20) to start program playing.
During program playing, press STOP (H18) to stop the program playing. Move
the cursor to and press ENTER (H20) to go to the previous page, or move
the cursor to and press ENTER (H20) to go to next page.
Move the cursor to the EXIT and press ENTER (H20) to exit the program playing.

ADVANCED FUNCTIONS

System Switch

During VCD/DVD playback mode, press P/N (H11) to set the TV standard to
PAL or NTSC or AUTO system.

• This can also be set by SETUP MENU.

Slow Motion Playback

During DVD playback mode, press (H10) to slow forward or slow backward.
There are speeds as follow:

NORMAL PLA YBACK

During VCD mode, press (H10) to slow play, there are speeds as follow:

NORMAL PLA YBACK

Zoom the View

During VCD/DVD/MPEG-4 mode, press ZOOM(H9) repeatedly to reach a de­sired size. There are sizes as follow: 2 times->3 times->4 times-> no change.

• To move the image from one area to another by pressing button , , , .

On Screen Display

During CD/VCD status, press OSD button (H8) and the display shows: Single
elapsed time-> Single remain time-> T otal elapsed time -> Total remain time->Off
(VCD).
During DVD status, press OSD button (H8) the display shows: Title elapsed
time->Title remain time-> Chapter elapsed time-> Chapter remain time-> OFF .
During MP4 status, press OSD button (H8) and the display shows: Single elapsed
time-> Single remaining time-> Off.

Skip backward/forward/F.F/F.REW the playback

In playback mode, press or (H20) to perform fast reward or fast forward.
Each pressing will change as follow: 2 times -> 4 times -> 8 times -> 16 times ->
NORMAL PLAYBACK.

LISTENING TO THE RADIO

When you enter Radio mode, the touch monitor will show as follow . Touch the
icon on the monitor directly to set corresponding status.

1. Band Indicator

2. Preset Number Indicator

3. Frequency Indicator

4. SEEK+/SEEK-

5. The 6 stations of the current band

6. BAND

7. AMS

8. RDS

9. SRC

Band Selector

During radio mode, repeatedly press BAND button (2/H3) to select bands in
following order: FM1->FM2->FM3->MW1 ->MW2

Manual/Automatic Tuning
Manual T uning

Press or button(H20) continuously to select a station downward or
upward respectively.

Automatic Tuning

Press and hold or (H20) for more than 3 seconds, the radio automatically
searches a station downward or upward respectively and plays when it finds a
station.

Selecting Station Directly

Press GOTO (H2), and the monitor shows FREQ, then press the Number to
input the valid frequency, then the station will be played.

• It is only valid when GOTO FREQ is on in main menu.

Scanning/Memorizing Stations Automatically

• By AMS button

Press AMS button(H4) to scan each stored station 6 seconds respectively which
stored in Number Buttons (from 1 to 6). Y ou can press the corresponding Num­ber Buttons or AMS button when your station is charged. And it starts playing the
station.
When press and hold AMS for more than 2 seconds, it will activate automatically
memory storing. The radio automatically selects a station and has it stored in any
one of Number Buttons. (from1 to 6).

Note:

- The unit can be stored up to 6 stations each band.

- Press AMS in the monitor also performs the same function.

By Number buttons

Press Number Buttons (H23) to receive the stored stations.
During radio status, Number Buttons (from 1 to 6) can help you store your favor­ite station.

1. When receiving a station, press and hold any one of the Number Buttons
(from 1 to 6) until the preset number appears on the LCD, which indicates that
station is already stored in the corresponding number button.

2. Press and hold AMS button to receive stations automatically, and store them
in 1 to 6 number respectively.

3. Press and hold another number button more than 2 seconds when listening in
a station in one number buttons, the station will be stored in that number button.

• Press Number buttons in the monitor performs the same function.

On Screen Display

During radio status, press OSD (H8) to setup, or press and hold OSD (H8) to
display the edition information. The preset frequency displays as the default setting.

DX/LOC Selector

During radio status, press LOC button (H5) to select strong or weak station
reception. “LOC” appears on the display and only local station is available. When
it disappears both distance and local stations can be received.

• This function is invalid in MW tuning.

Selecting the Stored Station

During radio status, press button (H20) to select the stored station upward,
press (H20) to select the stored station downward.

MO/ST Selector

During radio status, you can press ST (H6) button on the remote control to select
MONO mode or STEREO mode.
Stereo reception is charged when “Stereo” appears.
It is switched to MONO mode when “Stereo” disappears.

• It is only valid in FM tuning.

RDS Setup

1.

AF

Press it to activate AF function.

2.

TA

Press it to activate TA function.

3.

/
Press it to select PTY CODE.

4.

PTY

Press it to activate PTY function.

5.

During PTY ON, press this button to
search the playing track s type.

6.

BACK

Press it to turn to listening to the radio.
There can not be out of TP

7.

PS:

TO display the current RDS station’s programs information.

8.

SEARCH+/SEARCH Press it to tune automatically.

Alternative Frequencies

Briefly press 26 AF to activate the auto searching station function. When AF is
on, the RDS signal is weak or there is not, it will be found in the preseted fre­quencies and the whole bands.

Note:

* It is also performed by pressing 1 in the monitor.

Traffic Alarm

Briefly press 25 T A to activate the traffic alarm function. When AF is on, there is
TA displays on screen, or else, if there is no TP information, the mode will search
TA station automatically.
The TA is green when it is played by a station, if not, it is yellow.When TA is
playing, the volume will be adjusted to a TA level automatically.When in other
modes(such as DVD, AUX), if a TA program is played. The mode will skip to the
RDS status automatically. It will resume to the primary mode after the T A is over.

Note:
Press 2 in the monitor performs the same function.
When TA is off, there no TA on screen.

ＡＲ－２４６６Ｓ　ＩＢ　ＭＵＳＥ　００１　ＲＥＶ１　－　ＧＢ．ｐ６５ 2000-1-1, 6:021

GB - 8 GB -9 GB - 11

GB -10

GB - 12

GB - 13

GB - 14

GB - 15

Program T yp e

Briefly press 7 PTY to activate PTY function.
When PTY is on, PTY ON appears in the monitor, you can press UP/DOWN to
select the program type, and then press PTY CODE to search the special program.
And the screen displays PTY SEARCH.
If PTY is off, PTY OFF appears in the monitor , the searching is stopped.

Note:
* It is also performed by pressing 4 in the monitor.

SD CARD / USB PLAYBACK

Insert a SD card or USB: Press REL (7) when the unit is on. And when the TFT

slanted, insert a SD card into SD slot (11). Insert a USB flash disc into USB
cable. Then the programs will be played. When playing PIC file, press (H18)
and / on the monitor to select the option.
Notes when exiting a SD card or USB:

• During SD mode or USB mode, the main unit would switch to Disc or TUNER
mode directly when exit the SD card or USB.

• During other modes, press SD card or USB to quit, the main unit will keep the
previous mode.

Note:

• At anytime when unit work with memory card, make sure the SD card has been
properly inserted & locked in the card slot before you attempt to do any operation.
To avoid damage, DO NOT LEAVE YOUR FLASH MEMORY CARD IN UN
LOCK CONDITION.

• This unit might not support all the SD cards or USB.

• The unit might not support all the multimedia files stored in SD card or USB
because it includes some special playback procedure which might not be
compatible with the procedure of this unit.

• If disc, SD or USB stopped playback, please eject disc or change the play
source. If it still doesn’t work, please check the content inside disc, SD or USB;
you can also try another disc, SD or USB.

• If above solution still doesn’t work, please reset the unit.

AUX

Press SRC (1/H1) to switch to the Aux mode.
In Aux mode, select AUX SET to adjust AUDIO, VIDEO and VIDEO FORMATE
(Auto 1:P AL, NTSC, SECAM), (Auto 2: P-M, P-N).

GB - 16

DVD PLAYBACK SETTING

GOTO a desired section
For DVD

Press the GOTO button (H2) to set the playing time, the TFT (13) shows: Title /
Chapter / Audio/ Subtitle / Angle / TT time/ CH time / Repeat / Time Display.
Press / button (H20) to select options, then press ENTER (H20) to set the
status. Press number buttons (H23) to set the current status.

For CD disc
Press the GOTO button (H2) repeatedly to enter different GOTO modes.
Disc time:--:-- Input desired time of the disc
Track time :--:-- Input desired time of the track

For VCD disc

Press the GOTO button (H2) to set the playing time, the TFT (12) shows: Track/
Disc time / Track time / Repeat / Time Display.
Press / button (H20) to select options, then press ENTER (H20) to set the
status.
Press number buttons (H23) to set the current status.

For MP3/SD/USB
Press the GOTO button (H2), repeatedly to enter different GOTO modes.

--:--: Input desired playing time

---/total track number: track Input desired track number

For MPEG-4 mode
Press the GOTO button (H2) repeatedly to enter different GOTO modes.
Select:--- Input desired track number
Go T o-:--:-- Input desired playing time

Note: Press CLEAR (H22) to clear the mistake input.
Changing the viewing angle(Multi-angle)

For the DVDs with multi-angle recording feature (scenes shot from multiple
angles), you can press ANGLE (H7) to switch among viewing angles during
playback. Selection as follows: ANGLE 1—ANGLE 2—ANGLE 3……

1). The mark “ ” on a DVD’s package indicates it features multi-angle

scenes. The number in the mark indicates the number of angles from which
scenes were shot.

2). It is invalid to pressing ANGLE during fast forward/fast reverse or pause.

GB - 17

Changing audio language (Multi-audio)

For DVDs/MPEG-4 discs with multi-audio recordings function, you can press
AUDIO (H6) to switch between language and audio systems during playback.

Selection as follows: AUDIO 1— AUDIO 2— AUDIO 3......

• The number in the mark “ ” on a DVD’s package indicates the number of
recorded languages/audio systems.

Changing the subtitle language (Multi-subtitle)

For DVDs/MPEG-4 discs with multi-subtitle recordings function, you can press
SUB-T (H5) to switch between subtitle languages during playback. Selection as
follows: Subtitles 1— Subtitles 2—…— Subtitles off.

• The number in the mark “ ” on a DVD’s package indicates the number of
recorded subtitle anguages.

Selecting MENU

1. Selecting Menu: During DVD status, press MENU (H4) to return to the root
menu. Press ENTER (H20) or number (H23) button to select your desired
chapter.

2. Selecting T itle: During DVD status, press TITLE (H3) to return the title menu.
Press ENTER (H20) or (H23) button to select your desired title.

DVD Program and Title selection

When DVD program menu or title menu appears, you can press the menu or title
directly on the screen to select; Or, If the touch menu options invalid or the disc
dose not suport touch-TITLE, a remote control will display on the screen.
Press to left,press to right, press to up, press to down and press to
ENTER.

Playback control (VCD)

Press the TITLE button (H3) to access the PBC menu. Select your desired track
by number buttons. To cancel PBC playing, press TITLE button (H3) again.
* PBC playing confirms to version 2.0 or above disc only.

Setting Channel (VCD)

During VCD mode, repeatedly press AUDIO (H6) to select the following channel:
Stereo-> Mono left-> Mono right.

GB - 18

Set Up Main Menu

Press and hold SETUP (H19) button (only in Aux & Radio mode), the setting
picture appears as below.

T ouch the icon on the monitor directly to set corresponding status.

1. Video adjust 2. Audio Adjust

In this menu you can adjust COLOR,
TINT,BRIGHT, CONTRAST
PICTURE.

You can adjust VOLUME,
SUBWOOF, BALANCE, FAD,
BASS, TREBLE. Press to select,
and then press and to adjust.

Picture Adjust
Press PICTURE in this menu, it will

appear as follows:

Press EXIT to exit this menu.
Note: Adjusting the other options
perform the same operation.

Press and to adjust the size,
then press SAVE to save the setup,
press EXIT to exit this menu.
Note: Adjusting the other options per­form the same operation.

GB - 19 GB - 20 GB - 21 GB - 22

3. Source setup

4. System setup

In this menu you can adjust CLOCK
SYS, KEY BEEP and so on.
Note: If the item display in yellow,
then it cannot be set up.

Key Beep
In this menu you can adjust KEY BEEP,

In this menu you can adjust KEY
BEEP, press it in the monitor and se­lect ON or OFF, the default setting is
ON, it means when you press the
keys, they sounded.

In this menu, you can adjust all items to
be ON or OFF.

Clock System

Press CLOCK SYSTEM in the
monitor to set 12 HOUR or 24
HOUR in this menu.

Tips: Press to display the menu
follows, press to display the previ­ous one.

Reverse Pola

Setting REVERSE POLA in this menu.
The signal is +12V when you back a
car, please press BATTERY in the
monitor; if the signal is 0V, please
press GROUND.

AMS Fullup

In this menu to set the modes of AMS.
When the setup is ON, the presettable
stations are full, no news is allowed.
When you select OFF, it will search­ing continually.

Lamp SEL

In this menu you can adjust LAMP
SEL, press it in the monitor and se­lect ON or OFF, the default setting is
ON.

Local Area

You can select EUROPE or USA or
OIRT to search the stations quickly
by your current area. For example,
when you are in West Europe, you
can select EUROPE, and when you
are in East Europe, you can select
OIRT.

Local

In this menu to search the LOCAL
stations, when selected ON, the
strong signal local stations can be
received, when selected OFF, the
week signal out-of-town stations may
be received.

RT Scroll

T o select your desired speed, SLOW,
NORMAL, FAST. The default setting
is NORMAL.

Goto FREQ

To select ON, you can using GOTO
button on the remote control to select
a station’s frequency directly in radio
mode.

TA V olume

T o select your desired volume, LOW ,
NORMAL, HIGH. The default setting
is NORMAL.

REGION

To set the AF searching region, the
default setting is ON.

Clock Adjust

Press CLOCK ADJ in the monitor to
adjust the clock.

Ajust Screen

Press ADJ SCREEN to display the
above menu,there are a square but­ton in the top left corner . Press the
square button at place(1),then the
button will move to place(2), press it
at place(2), it will move to place(3),
then place(4), press SA VE at last.

DVD Setup Menu

Press SETUP (H19), main menu and sub-menu will appear on TFT, pressing /
/ / (H20) to select your desired items, then press ENTER (H20). Press
/ / / (H20) to move the cursor on “X”, then press ENTER to exit the
menu setup.

GB - 23

General setup page

MORE INFORMATION

- Do not use your set immediately after transport from a cold place to a warm
place, there may be condensation problems.

- Make sure that you keep your set away from water and high temperatures.

- Clean the player with a soft cloth, or a damp chamois leather. Never use solvents.

- The use of apparatus in moderate climates.

Note on discs

• Do not use irregular shape CDs (example: heart-shaped, octagonal ones). It

Dolby Digital Setup

may result in malfunctions.

• If there is a scratch, dirt or fingerprints on the disc, it may cause tracking error.
Before playing, clean the disc with a cleaning cloth. Wipe the disc from the
center out. Don’t store discs in places with high temperatures or high humidity,
they can become warped. After playing, store the disc in its case.

Replacing the Fuse

Make sure the amperage matches the specified value when replacing the fuses. If the
fuse is blown, check the power connection and replace with a new one. If the same
problem occurs, it would be subjected to the malfunction in-house. In such cases,
please consult the nearest service dealer.

Warning

Never use the fuse with the rated amperage more than that supplied to your unit,
otherwise it will damage the unit.

Preference page

TROUBLE SHOOTING

The following checklist might help to solve the problems which you meet when
using the unit. Please double check and make sure if the connection and the
procedure of the operation is properly before using the checklist below.

Problem

No power.

Some errors occur in the
LCD or no function when
pressing the button.

Unable to receive stations.

Poor effect on receiving a
station.

CDs cannot be loaded.

Sound skips.
No images.

Images skip.

Cause/Solution

Check and make sure whether the fuse is
blown, replace with proper value if necessary.

Press RESET button.

Check and make sure whether the antenna is
inserted or the antenna is properly connected,
if not, insert the antenna or connect it properly.

Antenna may not be the proper length. Make
sure the antenna is fully extended; if broken,
replace the antenna with a new one.

The antenna is poorly grounded, check and
make sure the antenna is properly grounded
at its mounting location.

A CD is loaded in the mechanism or remove
screen.

The CD is dirty or damaged.
The Video line from main unit to the TV is not

connected properly.
Improper setting of the color system. Set the

color system to “PAL” or “NTSC” according to
the connected television

Note:
If any of the problem persist after check list had been made, consult your nearest

SPECIFICATION

General

Power Requirement
Load Impedance
Max. Power Output
T one Controls

Dimensions
Mounting Dimension
Weight

FM Tuner Section

Tuning Range
IF Range
Usable Sensitivity (-30dB)
Signal-to-noise Ratio
Stereo Separation
Frequency Response

MW T uner Section

Frequency Range
IF Range
Usable Sensitivity (-20dB)

VCD/CD player section

VCD signal System
Signal-to-noise Ratio
Separation
Distortion

DVD Player Section

DVD Signal System
Number of channel
Frequency Response
Dynamic Range
Signal-to-Noise Ratio

14.4V DC(1 1-16V allowable)
4
40Wx4
±7dB
Bass 100Hz
Treble 10kHz
Approx.184x178x100mm(d/w/h)
Approx.164x183x112mm(d/w/h)
Approx.3.5kg

87.5-108(MHz)

10.7MHz
12dBuV
60dB
30dB (1kHz)
40-12000Hz

522-1620(kHz)
450kHz
28dBuV

AUTO/PAL/NTSC
60dB
60dB(1KHz)

0.3%

AUTO/PAL/NTSC
2 channels
40Hz to 16,000Hz
60dB
60dB

Audio & Video support formats:

MP3: 32kbps-320kbps
JPEG:up to 7296X5472 Pixels
MPEG: MPEG-1, MPEG-2, MPEG-4 ASP(DivX)
AVI: up to 720X576 Pixels
VOB(DVD): 720X480i, 720X576i, 720X480p, 720X576p
DivX: 3.11/4.0/5.0
USB: 2.0, 1.1, 1.0 (USB data transfer rate: USB1.1(full speed)

Note: Due to continuous product improvement, specifications and design are
subject to change without prior notice.

CAUTION ! This set uses a laser beam. To prevent any accident due to this type
of beam, the set should only be opened by properly trained personnel.
The unit conforms to the international safety specifications and to guide lines of
the european community and also complies with current standards concerning
electrical safety and electromagnetic compatibility EMC.

WARNINGS

A TTENTION: T o reduce the risk of electric shock, do not remove
the cover. There are no user serviceable parts inside the unit.
Refer all servicing to qualified personnel.

The lightning flash with arrowhead symbol within the triangle is a warning
sign alerting the user of “dangerous voltage” inside the unit.

The exclamation point within the triangle is a warning sign alerting the user
of important instructions accompanying the product.

CAUTION: Invisible laser radiation when open and interlocks defeated.
Avoid exposure to beam.

WARNING - To reduce the risk of fire or electric shock, do not expose this appli­ance to rain or moisture.

If at any time in the future you should need to dispose of this product
please note that Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice.(Waste Electrical and
Electronic Equipment Directive)

service dealer. Never attempt to disassemble your unit by yourself.

Due to continuous product improvement, the operations are subject to run
the model.

GB - 24 GB - 30

GB - 25

GB - 26

GB - 27

GB - 28

GB - 29

GB - 31

ＡＲ－２４６６Ｓ　ＩＢ　ＭＵＳＥ　００１　ＲＥＶ１　－　ＧＢ．ｐ６５ 2000-1-1, 6:032