Page 1
`NR
cloj=klK=TSVJMQQMTa
jqa=mкзЗмЕнл=^внбЙеЦЙлЙддлЕЬ~Сн=√=p~~êÄêΩÅâÉå=√=dÉêã~åó
Page 2
Page 3
Q
P
K
L
N
H
I
J
O
M
A
E
F
G
B
C
D
P
K
Q
L
R
M
N
A
F
S
J
E
T
O
I
Model A
1
Model B
2a
2b
2c
2
d
2e
Page 4
3
~
Ä
4
5 6a
8
7
~
Ä
9
10b
10a
11a
6b
11b
12
13
14
15
16
4
3
1
2
1
5
2
6
1
2
3
1
2
1
Page 5
17
19
18
1.
2.
3.
2.
1.
1.
20
22
21a
23a
21b
23b
24
25
26
1.
3.
B
3.
2.
1.
2.
A
1.
2.
Page 6
English
(Original operating instructions)
Français
(Notice d’instructions d’origine)
Deutsch
(Originalbetriebsanleitung)
Nederlands
(Originele gebruiksaanwijzing)
Italiano
(Istruzioni per l’uso originali)
Español
(Instrucciones de funcionamiento originales)
Svenska
(Originalbruksanvisning)
Dansk
(Originale driftsvejledning)
Norsk
(Originale driftsanvisningen)
Suomi
(Alkuperäinen käyttöohjekirja)
Português
(Instruções de serviço originais)
Ελληνικά
(Αυθεντικές οδηγίες χειρισμού)
Magyar
(Eredeti üzemeltetési útmutató)
Polski
(Oryginalna instrukcja obsługi)
4
16
30
42
54
67
80
115
127
140
91
154
166
103
Page 7
English Operating Instructions
Table of Contents
For your safety . . . . . . . . . . . . . . .4
Assembling the appliance . . . . . . .6
Operation and Display elements . .7
Operating safety . . . . . . . . . . . . . .9
Tips on lawn care . . . . . . . . . . . .11
Transporting the appliance . . . . .11
Cleaning/Servicing . . . . . . . . . . .11
Removing/Installing
and adjusting cutter deck . . . . . .13
Shutting down the machine . . . . .13
Warranty . . . . . . . . . . . . . . . . . . .14
Information about the engine . . .14
Troubleshooting . . . . . . . . . . . . .14
Information on the
identification plate
This information is very important
for subsequent identification,
ordering spare parts for the
appliance and for the customer
service desk. You will find the
identification plate under the
driver’s seat. Enter all the details
on your appliance’s rating plate in
the following fields.
You will find this and further
information about the appliance
in the separate CE-declaration of
conformity which is a component
part of the se operating
instructions.
The model number
identification
The fifth digit of the model number
specifies the Series, e.g.:
Model number: 13AF90GP690 =
means a model of the 900 Series.
Illustrations
Fold out the illustrated pages at
the start of the operating manual.
Graphical representations can vary
in detail from the appliance which
has been bought.
For your safety
Using the appliance
correctly
This unit is designed to be used
– as a lawn tractor for mowing
lawns of domestic and leisure
gardens,
– with accessories which are
expressly permitted for use
with this lawn tractor,
– according to the descriptions and
safety instructions provided in
these operating instructions.
Any other use is not as intended.
Improper use is not covered by the
warranty and the manufacturer will
reject any liability. The user is liable
for all damage to third parties and
their property.
The manufacturer accepts no
responsibility for damages
resulting from unauthorised
alterations to the unit that have
been carried out by the owner or
operator.
This mower is not licensed for use
on public roads or for transporting
people.
General safety notes
Carefully read these operating
instructions through before first
using the appliance and proceed
accordingly.
Tell other users about the correct
use of the vehicle.
Only operate the appliance in the
technical condition stipulated and
supplied by the manufacturer.
Carefully keep these operating
instructions in a safe place and
have them to hand. With a change
of ownership, pass the operating
instructions on with the appliance.
Spare parts and accessories must
satisfy the requirements specified
by the manufacturer.
Therefore use original spare parts
and original accessories only or
spare parts and accessories
authorised by the manufacturer.
Only allow repair work to be carried
out from a specialist garage.
Before working with
the appliance
If you are tired or ill, do not use
the unit.
Any person intending to use this
machine must not be under the
influence of intoxicants such as
alcohol, drugs or medicines.
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of the
appliance by a person responsible
for their safety.
Children should be supervised to
ensure that they do not play with
the appliance.
Persons under 16 years of age may
not operate the appliance. Local
regulations may fix the minimum
age.
Before commencing work with the
appliance, familiarise yourself with
all of the equipment and control
elements as well as with their
function.
Only store fuel in approved
containers and never in the
proximity of heat sources (e.g.
ovens, hot water tanks).
Replace the exhaust, fuel tank
or fuel cap immediately if they
become damaged.
Attach trailers and accessory
equipment in accordance with
the guidelines. Driving performance, especially steering, braking
capability, and overall stability are
affected by attachments, towed
items, ballast weights and the
weight of a grass catcher when full.
While working with the unit
When working with or on the unit,
wear appropriate work clothes (e.g.
safety boots, long trousers, tightfitting clothing, goggles and hearing
protection).
Only operate the appliance in
a technically flawless state.
Never change the engine settings
preset at the factory.
Never refuel the unit while the
engine is running or hot. Only fill
the tank in the open air.
4
Page 8
Operating Instructions English
Avoid naked flames, the formation
of sparks and do not smoke.
Ensure that no persons, especially
children, or animals are in the area
of operation.
Check the area in which you intend
to use the unit and remove all
objects that could be hit and
propelled by the unit. You can thus
avoid injuries and damage to the
unit.
Never mow on slopes that are
steeper than 20%. Working on
slopes is dangerous; the risk of
rollover and sliding is increased.
When working on slopes, always
drive off and halt the unit gently and
gradually. The transmission should
always be engaged when driving
down a slope – never coast – and
drive at a low speed. Never drive
across the face of a slope, always
up and down the slope.
Only use the unit in daylight or with
a sufficient level of artificial lighting.
The unit is not authorised for the
transport of people. Never allow
passengers on the unit.
Before any work on the
appliance
Protect yourself from injury. Before
doing any work to this appliance:
– turn the engine off,
– remove the ignition key,
– lock the parking brake.
– wait until all moving parts have
come to rest and the engine has
fully cooled.
– pull off the cap of the spark plug,
so that the engine cannot
inadvertently start.
After working with the appliance
Only leave the appliance once you
have turned off the engine,
actuated the parking brake and
have removed the ignition key.
Safety features
Safety features serve to protect you
and must always be functional.
You may not make any alterations
to the safety features or circumvent
their proper functioning.
Safety features are:
Grass flap
Fig. 19
The grass flap protects you against
possible injuries resulting from the
cutting blade or objects that are
propelled by it. The unit may only
be operated with the grass flap
attached.
Safety lock system
The safety interlock system will not
allow the engine to start unless
– the driver is sitting on the seat,
– the brake pedal has been
depressed or the parking brake
is in the park position,
– the direction lever or the
accelerator pedal is at “N”,
– the cutter deck is switched off,
i.e. PTO switch or PTO lever set
to “OFF” position (PTO = Power
Take Off).
The safety interlock system
switches the engine off as soon as
the operator leaves his seat without
actuating the parking brake or
switching off the cutter deck.
The safety interlock system
prevents rear discharge units from
mowing without attached deflector/
grass catcher (automatic
disconnection of engine or cutter
deck).
If units have no OCR function or the
OCR function is deactivated, the
safety interlock system prevents
the unit from reversing while the
cutter deck is switched on
(automatic disconnection of engine
or cutter deck).
Before reversing appliances with
PTO, therefore, switch OFF the
cutters at the PTO switch or PTO
lever.
Symbols on the appliance
Various symbols are stuck to the
appliance in the form of adhesive
labels. The following provides an
explanation of the symbols.
Warning!
Read the operating
instructions before
starting up.
Keep third parties
away from the danger
area!
Risk of injury from
rotating blades and
other rotating parts.
Keep hands and feet
out of the openings
when the machine
is running.
Risk of injury from
rotating blades and
other rotating parts.
Risk of injury from
propelled grass or
solid objects that are
propelled.
Working on steep
slopes increases
danger.
Always remove the
spark plug connector
before working on the
cutters! Keep fingers
and feet well away
from the cutters!
Always switch off
the appliance and
remove the spark
plug connector before
adjusting, cleaning or
checking it.
Attention! Risk of
explosion.
Battery acid/risk of
chemical burns.
Withdraw the key
from the ignition
before all work on the
unit and observe the
instructions in this
document.
5
Page 9
English Operating Instructions
When getting on and
off, never step on the
cutter deck.
Beware of hot
surface!
Remove the battery before tilting
the unit.
If operating with an attached trailer,
do not exceed the following
maximum values:
Max. gradient 14%
Max. support load on the
trailer coupling 25 kg
Max. trailer load
(trailer and load) 180 kg
The unit must not be operated
without the attached discharge
flap or the mulch locking part.
Keep these symbols visible on the
appliance.
Symbols used in these
instructions
The following symbols are used
in these instructions:
Danger
Your attention is drawn to dangers
in connection with the action
described and through which
there is a danger to persons.
Warning
Draws your attention to potential
hazards associated with the task
you are undertaking at the time
which could result in damage to
the mower.
Note
Points out important information
and tips concerning application.
Details concerning position
Where a position on, or in relation
to, the unit is described (e.g. left,
right), this is always from the
perspective of the driver, sitting on
the driver seat and facing forward.
Note concerning the
disposal of packaging
Any waste packaging or waste
appliances etc. which accumulate
should be disposed of according
to the local regulations.
Assembling the appliance
Commissioning the battery
Fig. 2
Danger
Risk of poisoning and injury from
battery acid
Wear protective goggles and
gloves. Prevent battery acid from
coming into contact with skin.
Should battery acid splash into
your face or eyes, wash immediately with cold water and consult
a doctor. Should you inadvertently
swallow battery acid, drink plenty
of water and consult a doctor
immediately. Keep batteries out of
the reach of children. Never tilt the
battery; the battery acid may run
out. Bring the remaining, unused
battery acid to your dealer or to
a waste disposal company.
Warning
Risk of fire, explosion and
corrosion due to battery acid
and battery acid gases
Immediately clean parts of the
appliance upon which battery acid
has been sprayed. Battery has
a corrosive effect. Do not smoke
and keep burning and hot objects
away. Store batteries in rooms
which are well ventilated and dry.
There is a risk of a possible short
circuit when working with the
battery. Do not place any tools or
metal objects on the battery.
Note
The battery is situated under the
passenger seat.
If a “maintenance-free/sealed”
battery (type 1) is supplied
(Battery without filler plugs)
The battery is filled with battery
acid and is sealed at the factory.
However, even a “maintenancefree” battery requires maintenance
if it is to have a longer service life.
Keep the battery clean.
Avoid tipping the battery.
Electrolyte fluid leaks from
a ‘sealed’ battery, if it is tipped.
Before using the battery for
the first time, charge it using
a battery charger (max. charging
current 12 Volt/6 Ampere) for
1 to 2 hours. After charging the
battery, first pull out the battery
charger plug, then disconnect
the battery (see also operating
instructions for the battery
charger).
If an empty battery (type 2)
is supplied
(Battery with filler plugs)
Fig. 2a–c
Remove the filler plugs of the
battery cells (Fig. 2b).
Fill each cell slowly with battery
acid up to 1 cm below the filling
opening.
Let the lead in the battery absorb
the battery acid for thirty minutes.
Check the level of the battery
acid, add more if necessary.
Before using the battery for
the first time, charge it using
a battery charger (max. charging
current 12 Volt/6 Ampere) for
2 to 6 hours. After charging the
battery, first pull out the battery
charger plug, then disconnect
the battery (see also operating
instructions for the battery
charger).
Re-insert the filler plugs of the
battery cells.
Install the battery in the
appliance.
Remove the strip seal from the
battery vent. Connect the venting
hose so that the free end points
downwards in the appliance.
The hose must always allow
free passage! (Fig. 2c)
6
Page 10
Operating Instructions English
First connect the red cable (+),
and then the black cable (–)
(Fig. 2a).
Thereafter, use only distilled
water to top up the battery
(check every 2 months).
Keep the battery clean.
Warning
Observe the order in which
the battery is mounted when
connecting/disconnecting the
terminals.
Fitting (Fig. 2a):
First connect the red cable
(+/positive pole) and then the
black cable (–/negative pole).
Removal:
First disconnect the black cable
(–/negative pole) and then the
red cable (+/positive pole).
Installing the steering wheel
Fig. 2d
Place the collar (2, if provided
with model) and the steering
wheel (1) on the steering shaft.
Place on top the washer (3) with
the convex side up, and secure
the steering wheel with the
screw (4).
Insert the cover (5).
Installing the seat
Fig. 2e
a) Seat with adjusting lever
b) Seat with adjusting screw
Removing the transport
securing device at the
ejector flap
Fig. 17
Depending on the model remove
the locking plate or cable tie.
The deflector closes automatically.
Operation and Display
elements
Warning. Damage to the
appliance.
The control and indicator functions
will be described to begin with.
Do not perform any functions at this
stage!
Fig. 1
Model A – Appliances with
hydrostatic drive
A Ignition lock with OCR function
BPTO-switch
C Forward pedal
D Reverse pedal
E Lever for setting the cutting
height
F Can holder
G Gear release lever *
H Storage bin
I Adjusting lever for seat
J Brake pedal
K Tank contents display
L Choke
M Switch for parking brake/
Speed control
N Throttle/Choke
O Fuel tank
P Display cluster
Q Steering wheel *
(* not visible)
Model B – units with automatic
drive
A Ignition lock with OCR function
E Lever for setting the cutting
height
F Can holder
I Adjusting lever for seat
J Brake pedal
K Tank contents display
L Choke
M Switch for parking brake/
Speed control
N Throttle/Choke
O Fuel tank
P Display cluster
Q Steering wheel *
R PTO lever
S Direction-of-travel lever
T Drive pedal
(* not visible)
Ignition lock with OCR function
(depending on model)
(A)
Fig. 3
This ignition lock features an OCR
function (= user-controlled mowing
in reverse gear).
Start: Turn the key to the right
until the engine is running, then
release. The key at
(normal) allows mowing in the drive
direction.
OCR position: Turn key to left of
normal position to reverse mowing
position and press the
switch (1).
The indicator light (2) comes on
and indicates to the user that the
unit can now mow in reverse and
forward gear.
Stopping: Turn the key to the left,
to .
Note
Do not use the OCR function
unless absolutely necessary,
otherwise work with the key in the
normal position. The OCR function
switches off automatically as soon
as the key is turned to the normal
position or the engine is switched
off (stop position or disconnection
of the engine by the safety interlock
system).
PTO switch (B)
(depending on model)
Fig. 6a
The PTO switch actuates an
mechanical clutch to switch ON
and OFF the cutters.
ON = pull the switch.
OFF = press the switch.
Note: When the safety lock system
has automatically switched OFF
the appliance (e.g. when reversing
with activated cutters), first switch
ON and then OFF the PTO switch
to release the lock on the clutch.
Forward pedal (C)
(Appliances with hydrostatic
drive)
Fig. 1
The pedal controls the speed
in a forward direction.
Reverse pedal (D)
(Appliances with
hydrostatic drive)
Fig. 1
The pedal controls the speed in
a reverse direction.
Information on forward/reverse
pedal
To stop or change direction of
travel, release the appropriate
pedal.
7
Page 11
English Operating Instructions
Lever for setting the cutting
height (E)
Fig. 1
Largest cutting height, cutters top
= lever to “H”.
Smallest cutting height, cutters
bottom = lever to “L”.
Can holder (F)
Fig. 1
Gear release lever (G)
(Appliances with hydrostatic
drive)
Fig. 11
To push the unit when the engine
is switched off.
Depending on model:
Pull out lever and press down
(Fig. 11a). To drive the unit,
push lever up and press in.
or
Pull out lever and press up
(Fig. 11b). To drive the unit,
push lever down and press in.
The lever is situated on the rear
panel of the machine.
Storage bin (H)
(depending on model)
Fig. 1
Adjustable seat (I) (optional)
Fig. 14
a) Pull the lever, and adjust the
seat.
or
b) Loosen adjusting screw, adjust
seat and retighten adjusting screw.
Brake pedal (J)
Fig. 1
The brake pedal can be used
to brake quickly, to engage and
disengage the locking brake,
and to switch OFF speed control.
Tank contents display (K)
Fig. 8
The inspection window indicates
the level of fuel in the fuel tank.
Parking brake/Speed control
(M)
Fig. 10
This switch has a dual function:
Actuate the parking brake:
Press down the brake pedal fully,
and press the switch.
Release the parking brake:
Press down the brake pedal fully,
the switch disengages.
Switching on Tempomat :
When driving, press the switch.
The forward speed selected at
this point (but not top speed) is
maintained, and the drive pedal
can be released.
When the accelerator pedal or
the brake pedal is depressed,
the cruise control automatically
switches off.
Choke (L/N) (depending
on model)
Fig. 5
To start a cold engine, pull the
choke (Fig. 5a), or move the
accelerator lever to (Fig. 5b).
Throttle (N)
Fig. 4
The engine speed can be adjusted
continuously. Fast engine speed
= . Slow engine speed = .
Fuel tank (O)
Fig. 1
Display cluster (P) (optional)
Fig. 7
According to the model, the
combination indicator can consist
of the following elements.
Oil pressure (1): The indicator light
is lit while the engine is running,
immediately switch off engine and
check oil level. Where necessary,
visit a garage.
Brake (2): Indicator lamp lights up
if the brake pedal is not depressed
or the parking brake is not locked
when the engine starts.
Cutter deck (PTO) (3): Indicator
lamp lights up if the cutter deck
(PTO) is not switched off when
the engine starts.
Battery charge indicator (4): If the
indicator light lights up when the
engine is running, this means
that the battery is not sufficiently
charged. Where necessary, visit
a garage.
Operating hour counter (5): This
function shows the operating hours
as full hours and 1/10 of an hour in
the display.
Ampere meter (6): This shows the
charging current from the generator
to the battery.
Optional functions:
– When the ignition is switched on,
the battery voltage indicator is
indicated for a short period and
then the operating hours are
indicated.
The operating hours are always
counted except for when the
ignition key is in the “Stop”
position or when it is removed.
– Each time 50 operating hours
have elapsed (according to the
model), the oil change indicator
“CHG/OIL” appears in the display
for five minutes. This message
appears after the next two hours
of operation. See the engine
manual for oil change intervals.
Steering wheel (Q)
Fig. 1
PTO lever (R)
Fig. 6b
The PTO lever actuates a mechanism to switch ON and OFF the
cutters.
Switch off cutter deck = pull
lever all the way backwards
Switch on cutter deck = slowly
press lever all the way forwards.
Direction-of-travel lever (S)
(Appliances with auto drive)
Fig. 9
The direction lever must be used
only when the tractor is stationary.
To do this, fully depress and hold
down the brake pedal.
Forwards = lever to “F/ ”
Idle = lever to “N”
Reverse = lever to “R/ ”
8
Page 12
Operating Instructions English
Drive pedal (T)
(Appliances with auto drive)
Fig. 1
The drive pedal is used to adjust
the speed continuously:
– Move the direction-of-travel lever
to “F” forwards ( ) or “R” reverse
().
– Forwards = push forwards the
drive pedal (in direction), the
further forward, the faster.
Light (depending on model)
Fig. 21
Switch on headlights = switch to
“ON”.
Some models do not feature the
light switch.
The headlights are lit as long as the
engine is running or the ignition key
is set to the position (depending
on model).
Operating safety
Follow the notes in the engine
manual as well!
Danger
Risk of injury
No person, especially children,
and/or animals should be allowed
to stand close to the mower while it
is in use. They could be injured by
stones or similar objects that might
be thrown out. Children must not
operate the appliance.
Be particularly careful when
mowing in reverse gear (units with
OCR switch). Ensure that all
persons are outside the working
area of the unit.
Never empty the grass catcher
while the engine is still running.
While emptying the grass catcher,
you yourself or some other person
could be injured if the contents of
the catcher are ejected at high
speed.
When mowing on steep slopes,
there is a risk of the mower tipping
over and you could be injured as
a result. Do not drive across the
face of a slope, but only straight up
and down. The unit may only be
driven on slopes up to max. 20%.
Never turn on a slope.
If the ground is wet the mower
could slip due to reduced traction
and overturn. Mow only when the
grass is dry.
Excessive speed can increase
the risk of an accident.
Maintain a safe distance at all times
from particularly steep slopes,
trees, bushes and hedges.
Pay particular attention when you
are travelling in reverse while
mowing at the same time.
Check the area in which you intend
to use the unit and remove all
objects that might be hit and
propelled by the unit.
If the cutting tool hits a foreign
object (e.g. stone) or if the machine
starts vibrating violently: stop the
engine immediately. Before using
the unit, have it checked for
damage by a specialist company.
In the case of mowers with rotary
blades, never stand in front of
grass ejection holes.
Never place your hands, feet, or
other parts of the body on or below
rotating parts.
Switch OFF the engine, remove the
ignition key, and disconnect the
spark plug terminal before you
clear the ejector of blockages and
other hindrances.
Do not use the unit in adverse
weather conditions, e.g. if there
is a probability of rain or a storm.
Risk of suffocation from carbon
monoxide
Only allow the combustion engine
to run in the open air.
Risk of explosion and fire
Fuel and petrol vapours are volatile
and fuel is highly flammable.
Before starting the engine, fill with
fuel. If the engine is still hot or
running, keep the fuel tank closed.
Only fill with fuel when the engine is
turned off and has cooled down.
Avoid naked flames, the formation
of sparks and do not smoke.
Only fill the tank in the open air.
Do not start the engine if fuel has
been filled up and has overflowed.
Wipe the affected areas clean and
wait until the fuel has vaporised.
To avoid the risk of fire, keep the
following parts free from grass of oil
leaks: engine, exhaust, battery, fuel
tank.
Danger
Risk of injury through the appliance
being faulty
Only operate the appliance in
a flawless state.
Carry out a visual check each time
before using the appliance. Check
articular the safety features,
p
in
cutting tools and mountings,
operation elements, and threaded
joints for damage and secureness.
Replace damaged parts before
operating.
Operating times
Observe the national and local
regulations concerning the hours
when the appliance can be used
(where necessary, enquire at your
appropriate local authority).
Before each use
Check:
all protective features
the engine-oil level
(see the engine handbook)
the fuel level
the tyre pressure
the side covering, accessory
equipment, the area around
the air filter for dirt and grass
Refuelling and checking
the oil level
Note
The engine has already been filled
with oil at the factory – please
check the oil, if required refill.
Fill up with lead-free petrol
(Fig. 24).
Fill the fuel tank to a maximum of
2 cm below the lower edge of the
filler neck.
Turn the fuel tank stopper tight.
Check the oil level (Fig. 25).
The oil level must be between
the “Full/Max.” and the
“Add/Min.” markings (see also
the engine handbook).
9
Page 13
English Operating Instructions
Check the tyre pressure
Note
For manufacturing reasons, the
tyre pressure can be higher than
necessary.
Check the tyre pressure. Correct
where necessary (see section
“Servicing”).
– front: 0.9 bar
– rear: 0.7 bar
Preparing for operation
Park the appliance on a firm level
surface and lock the parking
brake.
Conduct all work with the engine
switched off.
Remove the ignition key.
For all work on moving parts:
Open the bonnet and disconnect
the cable to the spark plug.
Set the driver seat
Fig. 14
Adjust the seat to the desired
position.
Setting the cutter wheels
Fig. 18
The cutter wheels should never
be lower than 6–12 mm above the
ground at the lowest cutter position.
The cutter wheels are not designed
to bear the loads generated by the
cutters and may have to be offset
accordingly.
Starting the engine
Sit in the driver seat.
Switch off cutter deck: Switch off
PTO and lift up cutter deck.
Push the brake pedal down fully
or lock the parking brake.
Move direction of travel lever/
drive lever to “N”.
Note
Units with hydrostatic drive are
in the “N” position when the
accelerator is not actuated.
Move throttle to .
To cold-start the engine, pull the
choke or move the accelerator
lever to .
Turn the ignition key to until
the engine is running (attempt
to start the engine for max.
5 seconds, wait 10 seconds
before attempting to start the
engine again). When the engine
is running, set the ignition key
to .
Slowly push back the choke.
Return the accelerator lever until
the engine runs smoothly.
Stopping the engine
Move the throttle to the middle
position.
Let the engine run for approx.
20 seconds.
Set ignition key to .
Remove the ignition key.
Engage the locking brake before
leaving the appliance.
Driving
Danger
Abrupt takeoff, stopping suddenly,
and driving at excessive speeds
raise the risk of accidents and
can cause damage to the unit.
Never set/adjust the driver’s seat
while the unit is moving.
Note
Be especially cautious when
reversing. Never change direction
without first stopping the appliance.
Start the engine as stated.
Move the direction lever to your
choice (on auto drive models
only).
Release the parking brake: Press
down fully the brake pedal, and
release it.
Slowly engage the drive pedal
until you have reached the speed
you want.
Stopping the appliance
Release the accelerator.
Press the brake pedal until
the appliance is stationary.
Mowing
Note
– In normal mowing mode
(see Operation, Ignition lock):
Before reversing, switch off and
lift up the cutter deck.
– In reverse mowing mode
(see Operation,
Ignition lock): Exercise particular
care when mowing in reverse
and activate only if absolutely
essential.
– Do not change direction when
the appliance is coasting or
driving.
Appliances with hydrostatic
drive
Start the engine as stated.
To ensure adequate power
output, move the throttle to .
Switch on the cutter deck.
Lower the cutters.
Release the parking brake: Press
down fully the brake pedal, and
release it.
Slowly depress the forward drive
pedal for forward direction of
travel and speed. The appliance
starts moving.
Appliances with auto drive
Start the engine as stated.
To ensure adequate power
output, move the throttle to .
Switch on the cutter deck.
Lower the cutters.
Move the direction-of-travel lever
to “F” (forwards).
Release the parking brake: Press
down fully the brake pedal, and
release it.
Engage the drive pedal slowly
to choose the forwards speed.
The appliance starts moving.
General information
When adjusting the cutting height
and driving speed, ensure that
the machine is not overloaded.
Depending on the length, type,
and dampness of the grass it may
become necessary to adjust the
cutting height and appliance speed
for the optimum grass catcher
performance.
If blockages occur, reduce the
driving speed and increase the
cutting height.
The best way to mow
Cut the first two rounds so the cut
grass is thrown out sideways into
the middle.
Never allow the grass to grow too
long
Never cut the grass too low.
10
Page 14
Operating Instructions English
Drive in a straight line.
Never mow at high speed,
particularly when a mulching kit
or grass catcher is installed.
Mulching
Various appliances can also mulch
when fitted with the corresponding
accessories. Ask your specialised
dealer for details.
Switching off the machine
Stopping the appliance: Release
the accelerator press brake
pedal until the appliance is
stationary.
Switch off the cutter deck.
Set the throttle lever into the
middle position.
Raise the cutters to the top.
Set the ignition key to “ ”
after twenty seconds.
Engage the locking brake
before leaving the appliance.
Remove the ignition key.
Pushing units with
hydrostatic drive
Fig. 11
Push the appliance only when the
engine is switched OFF.
Release the parking brake.
Releasing the gears
(depending on model):
– Pull out lever and press down
(Fig. 11a).
or
– Pull out lever and press up
(Fig. 11b).
Return the gear lock lever before
restarting the engine.
Tips on lawn care
Mowing
Lawns consist of various grass
types. Frequent mowing promotes
the growth of grass, resulting in
strong roots and a firm sward.
If you seldom cut the grass, you will
enhance the development of highgrowing types of grass and other
weeds, such as clover, daisies ...).
The normal height of a lawn is
approx. 4–5 cm. The grass should
only be cut back by 1/3rd of the
overall height at any one time.
Try not to cut the grass shorter than
4 cm, otherwise the lawn will suffer
during dry periods. If the grass
has grown particularly high (for
example, during a holiday period),
cut it back to its normal height in
several stages.
Mulching with accessory
(optional)
The grass is chopped up fine
(approx. 1 cm) during mowing
and is left on the lawn. The lawn
therefore retains a lot of nutrients.
Please note the following:
Do not mow wet grass.
Never mow more than max. 2 cm
of the total grass length.
Drive slowly.
Have the engine at max. rpm.
Clean the mower cover regularly.
Note
Attach mulching accessory
depending on the model.
Assembly examples in Fig. 21.
Transporting
the appliance
If changing location, drive the lawn
tractor short distances only.
otherwise transport it by vehicle.
Note: The mower is not approved
for public thoroughfares in
accordance with StVO.
Short distances
Danger
Solid objects may be hit/propelled
by the rotating cutting mechanism
causing damage.
Always switch off the cutting
mechanism before moving
the mower.
Long distances
Warning
Transport damages
The mode of transport used (e.g.
transport vehicle, loading ramp)
must be used in accordance with
guidelines (refer to the respective
operating instructions). When
transporting, secure the mower
against slipping.
Environmental hazard from leaking
fuel
The appliance must not be tilted
when it is transported.
Have the transporting vehicle
ready.
Lay the loading ramp to the
transporting vehicle.
With the unit in free-wheel, push
it up onto the transporting vehicle
(disengage the transmission in
the case of units with hydrostatic
drive).
Lock the parking brake.
Secure the machine to prevent
it from moving.
Cleaning/Servicing
Danger
Risk of injury through the engine
being unintentionally started.
Protect yourself from injury.
Before all work on this unit
– turn the engine off,
– remove the ignition key,
– lock the parking brake.
– wait until all moving parts have
come to rest and the engine has
fully cooled.
– remove the spark plug connector
on the engine in order to prevent
the engine from accidentally
being started.
Cleaning
Cleaning the machine
Warning
Do not use a high-pressure cleaner
for cleaning the vehicle.
If possible, clean the machine
directly after mowing.
Park the unit on a solid, even
surface.
Lock the parking brake.
Note
There is a particularly high risk of
rust and other corrosion when the
appliance is used in the winter.
Clean the appliance thoroughly
after every use.
11
Page 15
English Operating Instructions
Cleaning the cutting
mechanism
Danger
Injury hazard due to sharp cutting
blade
Wear protective gloves.
If the unit has more than one
cutting mechanism, moving one
cutting mechanism may cause the
other cutting mechanisms to move
as well. Take special care when
cleaning cutting mechanisms.
Warning
Damage to engine
Do not tilt the unit to more than 30°.
Fuel may run into the combustion
chamber causing engine damage.
Raise the cutting mechanism
fully.
Clean the area surrounding the
blade using a scrubbing brush or
cloth.
Cutters with cleaning nozzle
(optional)
Fig. 20
Place the appliance on an even
surface free of debris, stones, etc.,
and engage the locking brake.
1.Use a commercially available
quick-release coupling to attach
a water hose.
2.Start the engine.
3.Lower the cutter deck and switch
on for several minutes.
4.Switch off the cutter deck and
engine.
5.Detach the water hose.
Repeat steps 1 to 5 for the second
cleaning nozzle (if provided).
At the end of cleaning
(steps 1 to 5):
Raise the cutters to the top.
Start the engine and switch
on the cutter deck for several
minutes in order to dry the cutter
deck.
Servicing the vehicle
Observe the servicing guidelines in
the engine manual. At the end of
the grass-cutting season, have the
appliance checked and serviced in
a specialist workshop.
Warning
Threat to the environment through
engine oil
Pass on any waste oil which comes
about through an oil change to
a collection point or a waste
disposal company.
Threat to the environment through
batteries
Used batteries do not belong to
domestic rubbish. Pass on used
batteries to a dealer or a waste
disposal company. Dismantle the
battery before the vehicle is
scrapped.
Using jump leads
Danger
Never bridge a defective or frozen
battery with jump leads. Ensure
that the units and the jump lead
clips do not touch each other and
that the ignitions are switched off.
Connect the red jump lead to the
positive terminal (+) of the flat
battery and the donor battery.
Connect the black jump lead first
to the negative terminal (–) of the
donor battery. Connect the other
clip to the frame of the engine
block of the tractor with the flat
battery (as far away from the
battery as possible).
Note
If the donor battery is installed in
a vehicle, this vehicle must not be
started during the jump starting
process.
Start the tractor with the flat
battery and actuate the parking
brake.
Disconnect the jump leads
in reverse sequence.
Tyre pressure
Warning
Never exceed the maximum
permitted tyre pressure (see side of
tyre). When pumping up the tyres,
do not stand in front or above them.
The recommended tyre operating
pressure is:
front: 0.9 bar
rear: 0.7 bar
Over-inflating reduces
the longevity of the tyres.
Tyre pressure should be checked
before every journey.
After 5 operating hours
First engine oil change.
See engine manual for
subsequent intervals.
Use the oil channel or (optional)
quick oil drain (Fig. 16).
After 10 operating hours
Lubricate all rotating and bearing
points of the accelerator pedal
and brake pedal with several
drops of light oil.
Every 25 operating hours
Lubricate all cutter shafts, idlers,
and idler mounts with 251H EP
type grease applied to their
respective grease nipples.
This work should be performed
at a specialised workshop.
Lubricate the wheel bearings
and front wheel axes with
a multipurpose grease applied
to their respective grease
nipples.
Lubricate the cutters’ front
wheels with a multipurpose
grease applied to their grease
nipples.
Every 50 operating hours
Grass residue and other soiling
on the drive gears must be
removed at a specialised garage.
Every 2 months
For battery type 2 only – Fill
battery cells with distilled water
up to 1 cm beneath the filling
aperture.
If necessary
Charging the battery
When the appliance is not used
for longer periods, we recommend
removing the battery from the
appliance and charging this before
and every two months during
storage and before the appliance
is again put into operation.
Note
Note the information in the
operating instructions for your
battery charger.
Replace the fuse
Replace defect fuses only with
the equivalent rating.
12
Page 16
Operating Instructions English
Once a season
Apply multipurpose grease to
the teeth on the steering gear.
Lubricate the steering linkage
with a few drops of light oil.
Lubricate all moving parts and
bearing surfaces with a few
drops of oil (control levers,
cutting height adjustment).
Clean the spark plug and check
the gap between the electrodes
or replace the plug. See engine
handbook.
The rear axles must be lubricated
with a special-purpose (waterrepellent) grease at a specialised
garage.
Have the cutting blade
sharpened or replaced
in a specialist workshop.
Note
Regularly check (when visiting your
workshop) the condition of the
mower deck V-belt. This is particularly important for positively
controlled mower decks.
Removing/Installing and
adjusting cutter deck
Danger
Risk of injury through the engine
being unintentionally started.
Protect yourself from injury. Before
doing any work to this appliance:
– park the appliance on a level
surface,
– turn the engine off,
– remove the ignition key,
– switch off PTO,
– lock the parking brake.
– wait until all moving parts have
come to rest and the engine has
fully cooled.
– remove the spark plug connector
on the engine in order to prevent
the engine from accidentally
being started.
Danger
Risk of injury from sharp cutting
blade.
Wear protective gloves.
Disassembly
Install the cutter wheels at the
highest position.
Lower the cutters.
Remove the V belt from the PTO
clutch (motor pulley). Depending
on the model, remove the V-belt
guide bracket (Fig. 23)
beforehand. Ensure that the
location holes are used again
for subsequent installation.
Withdraw the pin (1, Fig. 15) to
disconnect the cutters from the
suspension.
Repeat these steps on the left
side of the appliance.
NOTE
– In doing so, support the
cutters firmly so that they cannot
simply drop to the ground.
Move the cutting height setting
lever into the top catch.
Remove fixing bracket from the
cutter deck (Fig. 22). Pull cotter
pin (A) and pull the fixing bracket
(B) out of the holder.
Pull out the cutters (to the right)
from beneath the appliance.
Assembly
To reinstall the cutters perform
the above steps (for removing
the cutters) in reverse order.
Work proceeds faster when you
are assisted by a second person.
Make sure that the suspension
units are in their respective
recesses on the cutter mount and
the pin has engaged correctly.
Setting the cutter level
When mowing does not appear to
be parallel to the lawn the cutters
can be aligned.
Note
Before aligning the cutters check
the tyre pressure on the appliance.
Setting the side level
Fig. 13
Raise the cutters to the top.
Carefully turn the outer cutters
(risk of injury) transverse to the
drive direction.
Measure the distance between
the ground and the ends of the
two outer cutters. The result
should be identical. To obtain
the correct level you may have to
turn the adjusting segment (2) on
the right cutter side. To do so first
loosen (but do not remove) the
cap bolt (1) and retighten this
after the adjustment.
Set the level from front to back
Fig. 12
Note
Set/check the side level before this
adjustment.
Raise the cutters to the top.
Carefully turn the outer cutters
(risk of injury) parallel to the drive
direction.
Measure the distance between
the ground and the end of the
right cutter. The end of the front
cutter should be about 3.2–6 mm
lower than the end of the rear
cutter. You may have to adjust
the front receiver. To do so,
loosen the locknut (1) and turn
the setting nuts (2) steadily to
obtain the correct level. After
setting, retighten the locknuts (1).
Shutting down
the machine
Warning
Damage to mower materials
Store the mower with engine
cooled down only in clean, dry
areas. Always protect the mower
against rust if it is to be left for
comparatively long periods, e.g.
over the winter.
At the end of the grass-cutting
season or if the mower is not going
to be used for longer than one
month:
Clean the mower and the grass
catcher.
Protect all metal parts against
rust by wiping them using an
oiled cloth or spray with spray oil.
Recharge the battery using
a battery charger.
13
Page 17
English Operating Instructions
Before winterising the appliance,
remove the battery. The battery
must then be charged and kept
in a dry, cool place (protected
against frost), and recharged
every 4 to 6 weeks and before
the next use.
Drain out the fuel (in an open
space) and prepare the engine
for storage as described in the
handbook for the engine.
Check the tyre pressure.
Park the mower in a clean,
dry room.
Warranty
In each country, the guarantee
conditions apply which are given
out by our company and/or the
importer.
We are happy to repair damage to
your appliance free of charge within
the scope of the guarantee in as far
as the damage is believed to be
caused by a material or a manufacturing fault. In making a claim
against the guarantee, refer to
place where the vehicle was sold
or the nearest branch office.
Information about the
engine
The engine manufacturer is liable
for all problems related to the
engine regarding performance,
measuring performance, technical
data, guarantee and service. You
will information in the separately
enclosed owner’s/operator’s
manual provided by the
manufacturer.
Problem Possible cause(s) Remedy
Starter does not react. Safety interlock system has
actuated.
Battery not connected properly. Connect the red cable to the positive (+)
Starter does not react. Empty or weak battery. Check the battery, charge it or exchange it.
Fuse has tripped. Exchange fuse. If the fuse trips repeatedly,
Loose earth (ground) lead
between engine and frame.
Starter runs, but engine does
not start.
Choke and throttle at wrong
position.
To start the engine, first sit down on the
driver’s seat. Press down fully the brake
pedal or engage the locking brake.
Switch off PTO.
terminal on the battery and the black cable
to the negative (–) terminal on the battery.
find the cause (usually short-circuit).
Connect the earth (ground) lead.
Actuate the choke. Move throttle to .
Troubleshooting
Danger
Risk of injury through the engine
being unintentionally started.
Protect yourself from injury.
Before all work on this unit
– turn the engine off,
– remove the ignition key,
– lock the parking brake.
– wait until all moving parts have
come to rest and the engine has
fully cooled.
– pull off the cap of the spark plug,
so that the engine cannot
inadvertently start.
Faults when operating your
appliance often have simple
causes which you should know
about and which you can partly
deal with yourself. In case of doubt,
your specialist garage will be happy
to help you further.
Carburettor not receiving any
fuel, fuel tank empty.
Defective or dirty spark plug. Check spark plug; see engine manual.
No ignition spark. Have ignition checked in repair shop.
Engine emits smoke. Too much oil in engine. Switch OFF appliance immediately.
Defective engine. Switch OFF appliance immediately. Get the
14
Top up with fuel.
Check engine oil level.
engine checked in a specialist garage.
Page 18
Operating Instructions English
Problem Possible cause(s) Remedy
Excessive vibration. Damaged blade drive shaft or
defective cutting blade.
Switch OFF appliance immediately.
Have defective parts replaced in a specialist
workshop.
Cutting mechanism does not
discharge grass or cuts
unevenly.
Engine is running, cutter deck
is not mowing.
Engine speed too low. Increase throttle.
Travelling speed too high. Set to a lower travelling speed.
Cutting blade is blunt. Arrange for service agent to sharpen or
replace blade.
V-belt torn. Have the V-belt replaced in a repair shop.
15
Loading...