i
G52-M7060X4
661FM2 Series
MS-7060 (v1.X) Micro ATX Mainboard
ii
Manual Rev: 1.2
Release Date: July 2004
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct
the interference at his own expense.
Notice 1
The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to
comply with the emission limits.
VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star International
MS-7060
iii
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR
INTERNATIONAL. We take every care in the preparation of this document,
but no guarantee is given as to the correctness of its contents. Our products
are under continual improvement and we reserve the right to make changes
without notice.
Trademarks
All trademarks are the properties of their respective owners.
AMD, Athlon™, Athlon™ XP, Thoroughbred™, and Duron™ are registered
trademarks of AMD Corporation.
Intel® and Pentium® are registered trademarks of Intel Corporation.
PS/2 and OS®/2 are registered trademarks of International Business Machines
Corporation.
Microsoft is a registered trademark of Microsoft Corporation. Windows® 98/
2000/NT/XP are registered trademarks of Microsoft Corporation.
NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or
trademarks of NVIDIA Corporation in the United States and/or other countries.
Netware® is a registered trademark of Novell, Inc.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc.
Kensington and MicroSaver are registered trademarks of the Kensington Technology Group.
PCMCIA and CardBus are registered trademarks of the Personal Computer
Memory Card International Association.
Revision History
Revision Revision History Date
V1.0 First release for PCB 1.x with May 2004
chipsets SiS661FX & SiS964
V1.1 Special version for Medion June 2004
V1.2 Update marketing name and add July 2004
RAID content
iv
1. Always read the safety instructions carefully.
2. Keep this User’s Manual for future reference.
3. Keep this equipment away from humidity.
4. Lay this equipment on a reliable flat surface before setting it up.
5. The openings on the enclosure are for air convection hence protects the
equipment from overheating. Do not cover the openings.
6. Make sure the voltage of the power source and adjust properly 110/220V
before connecting the equipment to the power inlet.
7. Place the power cord such a way that people can not step on it. Do not
place anything over the power cord.
8. Always Unplug the Power Cord before inserting any add-on card or module.
9. All cautions and warnings on the equipment should be noted.
10. Never pour any liquid into the opening that could damage or cause electrical
shock.
11. If any of the following situations arises, get the equipment checked by a
service personnel:
h The power cord or plug is damaged.
h Liquid has penetrated into the equipment.
h The equipment has been exposed to moisture.
h The equipment has not work well or you can not get it work according
to User’s Manual.
h The equipment has dropped and damaged.
h The equipment has obvious sign of breakage.
12. Do not leave this equipment in an environment unconditioned, storage
temperature above 600 C (1400F), it may damage the equipment.
Safety Instructions
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
v
CONTENTS
FCC-B Radio Frequency Interference Statement ............................................ ii
Copyright Notice ........................................................................................... iii
Revision History ........................................................................................... iii
Safety Instructions ....................................................................................... iv
Chapter 1. Getting Started ........................................................................ 1-1
Mainboard Specifications .................................................................... 1-2
Mainboard Layout ............................................................................... 1-4
Chapter 2. Hardware Setup ....................................................................... 2-1
Quick Components Guide ..................................................................... 2-2
Central Processing Unit: CPU .............................................................. 2-3
CPU Core Speed Derivation Procedure .......................................... 2-3
Memory Speed/CPU FSB Support Matrix ..................................... 2-3
CPU Installation Procedures for Socket 478 .................................. 2-4
Installing the CPU Fan ................................................................... 2-5
Memory ................................................................................................ 2-7
Introduction to DDR SDRAM ........................................................ 2-7
DDR Module Combination ............................................................ 2-8
Installing DDR Modules ................................................................ 2-8
Power Supply ....................................................................................... 2-9
ATX 20-Pin Power Connector: CONN1 ......................................... 2-9
ATX 12V Power Connector: JPW1 ................................................ 2-9
Back Panel .......................................................................................... 2-10
Mouse Connector ....................................................................... 2-10
Keyboard Connector ................................................................... 2-11
USB Connectors .......................................................................... 2-11
Serial Port Connector ................................................................... 2-12
VGA Connector ............................................................................ 2-12
IEEE 1394 Port (Optional) ............................................................ 2-12
RJ-45 LAN Jack ........................................................................... 2-13
vi
Audio Port Connectors ............................................................... 2-13
Parallel Port Connector: LPT1 ...................................................... 2-14
Connectors ............................................................................................... 2-15
Floppy Disk Drive Connector: FDD1 ............................................ 2-15
Fan Power Connectors: CPUFAN1 & SYSFAN1 ......................... 2-15
Hard Disk Connectors: IDE1 & IDE2 ........................................... 2-16
Serial ATA HDD Connectors: SATA1 & SATA2 ......................... 2-17
IEEE 1394 Connector: J1394_2 (Optional) .................................... 2-18
Serial Port Connector: JCOM1 ..................................................... 2-18
Chassis Intrusion Switch Connector: JCI1 .................................. 2-19
Front Panel Connectors: JFP1 & JFP2 ......................................... 2-19
CD-In Connector: JCD1 ............................................................... 2-20
Front Panel Audio Connector: JAUD1 ........................................ 2-20
Front USB Connectors: JUSB1 & JUSB2 ..................................... 2-21
SPDIF Connector: JSP1 ............................................................... 2-21
Jumpers .............................................................................................. 2-22
Clear CMOS Jumper: JBAT1 ........................................................ 2-22
Slots ................................................................................................... 2-23
AGP (Accelerated Graphics Port) Slot ......................................... 2-23
PCI (Peripheral Component Interconnect) Slots .......................... 2-23
PCI Interrupt Request Routing .................................................... 2-23
Chapter 3. BIOS Setup .............................................................................. 3-1
Entering Setup ...................................................................................... 3-2
Control Keys ................................................................................. 3-2
Getting Help .................................................................................. 3-3
The Main Menu ................................................................................... 3-4
Standard CMOS Features ..................................................................... 3-6
Advanced BIOS Features ..................................................................... 3-8
Advanced Chipset Features ............................................................... 3-11
Integrated Peripherals ........................................................................ 3-14
vii
Power Management Setup .................................................................. 3-17
PNP/PCI Configurations ..................................................................... 3-21
PC Health Status ................................................................................ 3-23
Frequency/Voltage Control ................................................................ 3-24
Load Fail-Safe/Optimized Defaults ...................................................... 3-25
Set Supervisor/User Password ........................................................... 3-26
Chapter 4. Introduction to SiS964 SATA RAID ....................................... 4-1
Introduction ......................................................................................... 4-2
System Requirement ...................................................................... 4-2
RAID Basics .................................................................................. 4-2
Performance hints and recommend setting .................................... 4-2
RAID 0 (Striping array) .................................................................. 4-3
RAID 1 (Mirror array) .................................................................... 4-3
JBOD (Spanning array) .................................................................. 4-3
System BIOS Setup .............................................................................. 4-4
BIOS Configuration .............................................................................. 4-5
Starting BIOS Utility ...................................................................... 4-5
Create a RAID 0 (Stripe) Array for performance ............................. 4-8
Create a RAID 1 (Mirror) Array for performance .......................... 4-12
Create a JBOD Array for performance .......................................... 4-16
Delete a RAID array ..................................................................... 4-18
Installing Software ............................................................................. 4-21
Install Driver in Windows XP/2000 .............................................. 4-21
Installation of SiS SATA RAID Driver ......................................... 4-22
viii
Appendix: Using 4- or 6-Channel Audio .................................................... A-1
Installing the Audio Driver .................................................................. A-2
Installation for Windows 98SE/ME/2000/XP ................................A-2
Using 4- or 6-Channel Audio Function ................................................ A-4
Using the Back Panel ....................................................................A-4
Testing the Connected Speakers ......................................................... A-9
Testing Each Speaker ................................................................... A-9
Playing KaraOK ................................................................................ A-11
Playing KaraOK .......................................................................... A-11
1-1
Hardware Setup
Chapter 1. Getting
Started
Thank you for purchasing 661FM2 Series (MS-7060 v1.X) Micro ATX mainboard.
The 661FM2 series is based on SiS® 661FX & SiS® 964 chipsets for optimal
system efficiency. Designed to fit the advanced Intel® Pentium 4 processor in
the 478-pin package, the 661FM2 series delivers a high performance and
professional desktop platform solution.
Getting Started
1-2
MS-7060 Micro ATX Mainboard
Mainboard Specifications
CPU
h Socket 478 for P4 Celeron/Celeron D(FSB 400/533 Mhz)/Northwood/
Prescott CPUs with FSB400/533/800MHz up to 3.4GHz.
(For the latest information about CPU, please visit http://www.msi.com.tw/program/
products/mainboard/mbd/pro_mbd_cpu_support.php )
Chipset
h SiS ® 661FX
- Supports Intel Pentium 4 processors with data transfer rate up to 800MHz
- Supports 64-bit high performance DDR400/DDR333/DDR266 memory controller
- Supports high performance & high quality 3D Graphic Accelerator
- Supports AGP 8x/4x interface
- Supports bi-directional 16-bit data bus with 1GHz bandwidth
h SiS® 964
- Supports Dual IDE AT A 100/133
- Integrated audio controller with AC97 interface
- Supports HyperTransport Technology
- Advanced power management and PC2001 compliance
- Serial ATA host controller
- Dual IDE Master/Slave Controller
Main Memory
h Supports two memory banks using two 184-pin unbuffered DDR DIMMs.
h Supports up to 2GB memory size without ECC.
h Supports DDR266/333/400.
(For the updated supporting memory modules, please visit http://www.msi.com.tw/
program/products/mainboard/mbd/pro_mbd_trp_list.php )
Slots
h One 8x/4x AGP (Accelerated Graphics Port) universal slot.
h Three PCI 2.2 32-bit Master PCI Bus slots.
On-Board IDE
h Dual IDE controllers integrated in SiS® 964.
h Support Bus Master, Ultra DMA 33/66/100/133 operation modes.
h Can connect up to four IDE devices.
1-3
Hardware Setup
On-Board Peripherals
h On-Board Peripherals include:
- 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and 2.88
Mbytes.
- 2 serial ports (one is pinheader) + 1 VGA port
- 1 PS2 keyboard + 1 PS2 mouse connectors
- 1 parallel port supports SPP/EPP/ECP mode
- 8 high speed USB 2.0/1.1 ports (Rear * 4 / Front * 4)
- 1 audio (Line-In/Line-Out/Mic-In) port
- 1 SPDIF-Out pinheader
- 1 RJ-45 LAN connector
- 2 IEEE 1394 ports (Real * 1/ Front * 1 with pinheader) (Optional)
- 1 CD-In pinheader
Audio
h AC97 link controller integrated in SiS® 964.
h 5.1 channels Realtek ALC655 S/W audio codec
- Comply with AC97 2.3 Spec
- Meets PC2001 audio performance requirement
- Can support SPDIF out via a 3-pin SPDIF-Out pinheader.
LAN
h Fast Ethernet integrated in SiS® 964.
h Realtek 8201BL LAN PHY.
h IEEE 802.3 and 802.3x Standard Compatible
h Supports ACPI v1.0b and PCI power management v1.1 Standard
BIOS
h 4MB Award BIOS with PNP BIOS, ACPI, SMBIOS 2.3, Green and Boot Block.
h Provides DMI 2.0, WFM 2.0, WOL, WOR, chassis intrusion, and SMBus for system
management.
Dimension
h Micro-ATX Form Factor: 9.6 inch (L) x 9.6 inch (W).
Mounting
h 9 mounting holes.
1-4
MS-7060 Micro ATX Mainboard
Mainboard Layout
661FM2 Series (MS-7060) v1.X Micro A TX Mainboard
BATT
+
S
i
S
9
6
4
D
I
M
M
1
D
I
M
M
2
JAUD1
JCD1
JFP1
JFP2
JUSB2
JUSB1
SYSFAN1
CPU
FAN1
JBAT1
B
I
O
S
PCI Slot 3
PCI Slot 2
PCI Slot 1
I
D
E
1
I
D
E
2
JCOM1
Top : Parallel Port
Bottom:
COM port
VGA port
Top : mou s e
Bottom: keyboa rd
Top: LAN Jack
Bottom: USB
ports
Top: 1394 port (Optional)
Bottom: USB por t s
Codec
Realtek
8201BL
JPW1
Line-In
Line-Out
Mic
FDD1
JCI1
Winbond
W83697HF
VIA
VT6307
SiS
661FX
AGP Slot
SATA2
SATA1
CONN1
J1394_2 (Optional)
JSP1
2-1
Hardware Setup
Chapter 2. Hardware
Setup
This chapter tells you how to install the CPU, memory modules, and expansion
cards, as well as how to setup the jumpers on the mainboard. It also provides the
instructions on connecting the peripheral devices, such as the mouse, keyboard,
etc.
While doing the installation, be careful in holding the components and follow the
installation procedures.
Hardware Setup
2-2
MS-7060 Micro ATX Mainboard
Quick Components Guide
CPU, p.2-3
Back Panel
I/O, p.2-10
FDD1, p.2-15
JUSB1, p.2-21
PCI Slots, p.2-23
IDE1, IDE2,
p.2-16
JBAT1, p.2-22
JPW1, p.2-9
JAUD1, p.2-20
CONN1, p.2-9
JCD1, p.2-20
JFP2, p.2-19
CPUFAN1, p.2-15
DDR DIMMs, p.2-7
JSP1, p.2-21
AGP Slot,
p.2-23
SYSFAN1,
p.2-15
J1394_2, p.2-18
JCOM1, p.2-18
JCI1, p.2-19
JUSB2, p.2-21
JFP1, p.2-19
SATA1, p.2-17
SATA2, p.2-17
2-3
Hardware Setup
Central Processing Unit: CPU
CPU Core Speed Derivation Procedure
If CPU Clock = 100MHz
Core/Bus ratio = 17
then CPU core speed = Host Clock x Core/Bus ratio
= 100MHz x 17
= 1.7 GHz
The mainboard supports Intel® Pentium® 4 Prescott & Northwood processor in the 478
pin package. The mainboard uses a CPU socket called PGA478 for easy CPU installation.
When you are installing the CPU, make sure the CPU has a heat sink and a
cooling fan attached on the top to prevent overheating. If you do not find the
heat sink and cooling fan, contact your dealer to purchase and install them before
turning on the computer. (For the latest information about CPU, please visit http://www.
msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support.php )
Memory Speed/CPU FSB Support Matrix
FSB
Memory
DDR 266
400 MHz
DDR 333
533 MHz
OK
OK OK
800 MHz
OK OK
DDR 400
OK
OK
OK
OK
MSI Reminds You...
Overheating
Overheating will seriously damage the CPU and system. Always make
sure the cooling fan can work properly to protect the CPU from
overheating.
Replacing the CPU
While replacing the CPU, always turn off the ATX power supply or unplug
the power supply’s power cord from grounded outlet first to ensure the
safety of CPU.
2-4
MS-7060 Micro ATX Mainboard
CPU Installation Procedures for Socket 478
1. Please turn off the power and
unplug the power cord before
installing the CPU.
2. Pull the lever sideways away
from the socket. Make sure to
raise the lever up to a 90-degree
angle.
3. Look for the gold arrow. The gold
arrow should point towards the
lever pivot. The CPU can only fit
in the correct orientation.
4. If the CPU is correctly installed,
the pins should be completely
embedded into the socket and can
not be seen. Please note that
any violation of the correct installation procedures may cause permanent damages to your
mainboard.
5. Press the CPU down firmly into
the socket and close the lever.
As the CPU is likely to move while
the lever is being closed, always
close the lever with your fingers
pressing tightly on top of the CPU
to make sure the CPU is properly
and completely embedded into
the socket.
Open Lever
90 degree
Sliding
Plate
Close
Lever
Press down
the CPU
Gold arrow
Gold arrow
Gold arrow
Correct CPU plac em ent
Incorrect CPU pl ace men t
X
O
2-5
Hardware Setup
Installing the CPU Fan
As processor technology pushes to faster speeds and higher performance, thermal
management becomes increasingly important. To dissipate heat, you need to attach the
CPU cooling fan and heatsink on top of the CPU. Follow the instructions below to install
the Heatsink/Fan:
2. Position the heatsink onto the retention
mechanism.
1. Locate the CPU and its retention
mechanism on the motherboard.
3. Mount the fan on top of the heatsink.
Press down the fan until its four clips
get wedged in the holes of the retention
mechanism.
4. Press the two levers down to fasten
the fan. Each lever can be pressed
down in only ONE direction.
retention mechanism
levers
2-6
MS-7060 Micro ATX Mainboard
5. Connect the fan power cable from the mounted fan to the 3-pin fan power connector
on the board.
fan power cable
NOTES
2-7
Hardware Setup
Memory
The mainboard provides two 184-pin unbuffered DDR266/DDR333/DDR400 DDR SDRAM,
and supports the memory size up to 2GB without ECC. To operate properly, at least one
DIMM module must be installed.
(For the updated supporting memory modules, please visit http://www.msi.com.tw/
program/products/mainboard/mbd/pro_mbd_trp_list.php )
DDR DIMM Slots
(DDR 1~2)
Introduction to DDR SDRAM
DDR (Double Data Rate) SDRAM is similar to conventional SDRAM, but doubles the rate
by transferring data twice per cycle. It uses 2.5 volts as opposed to 3.3 volts used in
SDR SDRAM, and requires 184-pin DIMM modules rather than 168-pin DIMM modules
used by SDR SDRAM.
2-8
MS-7060 Micro ATX Mainboard
DDR Module Combination
Install at least one DIMM module on the slots. Memory modules can be installed on the
slots in any order. You can install either single- or double-sided modules to meet your
own needs.
Memory modules can be installed in any combination as follows:
Installing DDR Modules
1. The DDR DIMM has only one notch on the center of module. The module will only fit
in the right orientation.
2. Insert the DIMM memory module vertically into the DIMM slot. Then push it in until the
golden finger on the memory module is deeply inserted in the socket.
3. The plastic clip at each side of the DIMM slot will automatically close.
MSI Reminds You...
You can barely see the golden finger if the module is properly
inserted in the socket.
Volt
Notch
S: Single Side D: Double Side
Slot Memory Module Total Memory
DDR 2
(Bank 2 & 3) S/D 64MB~1GB
Maximum System Memory Supported 64MB~2GB
DDR 1
(Bank 0 & 1) S/D 64MB~1GB
2-9
Hardware Setup
Power Supply
The mainboard supports ATX power supply for the power system. Before inserting the
power supply connector, always make sure that all components are installed properly
to ensure that no damage will be caused.
ATX 20-Pin Power Connector: CONN1
This connector allows you to connect to an ATX power supply. To connect to the ATX
power supply, make sure the plug of the power supply is inserted in the proper
orientation and the pins are aligned. Then push down the power supply firmly into the
connector.
ATX 12V Power Connector: JPW1
This 12V power connector is used to provide power to the CPU.
PIN SIGNAL
1 GND
2 GND
3 12V
4 12V
JPW1 Pin Definition
PIN SIGNAL
11 3.3V
12 -12V
13 GND
14 PS_ON
15 GND
16 GND
17 GND
1 8 -5V
19 5V
20 5V
PIN SIGNAL
1 3.3V
2 3.3V
3 GND
45V
5 GND
65V
7 GND
8 PW_OK
9 5V_SB
10 12V
CONN1 Pin Definition
CONN1
JPW1
10
1
20
11
MSI Reminds You...
Power supply of 300-watt (and above) is highly recommended for
system stability.
1
3
2
4
2-10
MS-7060 Micro ATX Mainboard
The back panel provides the following connectors:
Back Panel
Mouse Connector
The mainboard provides a standard PS/2® mouse mini DIN connector for attaching a PS/
2® mouse. You can plug a PS/2® mouse directly into this connector. The connector
location and pin assignments are as follows:
PIN SIGNAL DESCRIPTION
1 Mouse DATA Mouse DAT A
2 NC No connection
3 GND Ground
4 VCC +5V
5 Mouse Clock Mouse clock
6 NC No connection
Pin Definition
Mouse
Parallel
USB Port
Keyboard
MIC
LAN
VGA Port USB Port
1394
(Optional)
COM Port
L-in
L-out
PS/2 Mouse (6-pin Female)
2
1
3
4
5
6
2-11
Hardware Setup
Keyboard Connector
The mainboard provides a standard PS/2® keyboard mini DIN connector for attaching a
PS/2® keyboard. You can plug a PS/2® keyboard directly into this connector.
PS/2 Keyboard (6-pin Female)
2
1
3
4
5
6
USB Connectors
The mainboard provides a UHCI (Universal Host Controller Interface) Universal Serial
Bus root for attaching USB devices such as keyboard, mouse or other USB-compatible
devices. You can plug the USB device directly into the connector.
USB Ports
1 2 3 4
5 6 7 8
PIN SIGNAL DESCRIPTION
1 VCC +5V
2 -Data 0 Negative Data Channel 0
3 +Data0 Positive Data Channel 0
4 GND Ground
5 VCC +5V
6 -Data 1 Negative Data Channel 1
7 +Data 1 Positive Data Channel 1
8 GND Ground
USB Port Description
PIN SIGNAL DESCRIPTION
1 Keyboard DATA Keyboard DAT A
2 NC No connection
3 GND Ground
4 VCC +5V
5 Keyboard Clock Keyboard clock
6 NC No connection
Pin Definition
2-12
MS-7060 Micro ATX Mainboard
Serial Port Connector
The mainboard offers one 9-pin male DIN connector. It is 16550A high speed communication port that sends/receives/ 16 bytes FIFOs. You can attach a serial mouse or other
serial device directly to it.
9-Pin Male DIN Connector
1 2 3 4 5
6 7 8 9
PIN SIGNAL DESCRIPTION
1 DCD Data Carry Detect
2 SIN Serial In or Receive Data
3 SOUT Serial Out or Transmit Data
4 DTR Data Terminal Ready)
5 GND Ground
6 DSR Data Set Ready
7 RTS Request T o Send
8 CTS Clear T o Send
9 RI Ring Indicate
Pin Definition
VGA Connector
The mainboard provides a DB 15-pin female connector to connect a VGA monitor.
VGA Connector,DB 15-pin
1
5
11
15
Pin Signal Description
1 RED
2 GREEN
3 BLUE
4 N/C
5 GND
6 GND
7 GND
8 GND
Pin Signal Description
9 +5V
10 GND
1 1 N/C
12 SDA
13 Horizontal Sync
14 Vertical Sync
15 SCL
IEEE 1394 Port (Optional)
The back panel provides one standard IEEE 1394 port. The standard IEEE 1394 port
connects to IEEE 1394 devices without external power. The IEEE 1394 high-speed
serial bus complements USB by providing enhanced PC connectivity for a wide range
of devices, including consumer electronics audio/video (A/V) appliances, storage
peripherals, other PCs, and portable devices.
1394 Port
2-13
Hardware Setup
RJ-45 LAN Jack
The mainboard provides one standard RJ-45 jack for connection to Local Area Network
(LAN). You can connect a network cable to the LAN jack.
RJ-45 LAN Jack
MSI Reminds You...
For advanced audio application, Realtek ALC 655 is provided to offer
support for 6-channel audio operation and can turn rear audio
connectors from 2-channel to 4-/6-channel audio. For more information
on 6-channel audio operation, please refer to Appendix. Using 4or 6-Channel Audio Function.
Pin Definition
PIN SIGNAL DESCRIPTION
1 TDP Transmit Differential Pair
2 TDN Transmit Differential Pair
3 RDP Receive Differential Pair
4 NC Not Used
5 NC Not Used
6 RDN Receive Differential Pair
7 NC Not Used
8 NC Not Used
Audio Port Connectors
Line Out is a connector for Speakers or Headphones. Line In is used for external CD
player, Tape player, or other audio devices. Mic is a connector for microphones.
1/8” Stereo Audio Connectors
Line Out
Line In
MIC
2-14
MS-7060 Micro ATX Mainboard
Parallel Port Connector: LPT1
The mainboard provides a 25-pin female centronic connector as LPT. A parallel port is
a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode.
13 1
14
25
PIN SIGNAL DESCRIPTION
1 STROBE Strobe
2 DAT A0 Data0
3 DAT A1 Data1
4 DAT A2 Data2
5 DAT A3 Data3
6 DAT A4 Data4
7 DAT A5 Data5
8 DAT A6 Data6
9 DAT A7 Data7
10 ACK# Acknowledge
11 BUSY Busy
12 PE Paper End
1 3 SELECT Select
1 4 AUTO FEED# Automatic Feed
15 ERR# Error
1 6 INIT# Initialize Printer
17 SLIN# Select In
18 GND Ground
19 GND Ground
20 GND Ground
21 GND Ground
22 GND Ground
23 GND Ground
24 GND Ground
25 GND Ground
Pin Definition
2-15
Hardware Setup
The mainboard provides connectors to connect to FDD, IDE HDD, case, LAN, USB
Ports, IR module and CPU/System/Power Supply FAN.
Floppy Disk Drive Connector: FDD1
The mainboard provides a standard floppy disk drive connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types.
Connectors
FDD1
Fan Power Connectors: CPUFAN1 & SYSFAN1
The CPUFAN1 (processor fan) and SYSFAN1 (system fan) support system cooling fan
with +12V. They support three-pin head connector. When connecting the wire to the
connectors, always take note that the red wire is the positive and should be connected
to the +12V, the black wire is Ground and should be connected to GND. If the mainboard
has a System Hardware Monitor chipset on-board, you must use a specially designed
fan with speed sensor to take advantage of the CPU fan control.
MSI Reminds You...
Always consult the vendors for proper CPU cooling fan.
CPUFAN1
SYSFAN1
SENSOR
+12V
GND
SENSOR
+12V
GND
2-16
MS-7060 Micro ATX Mainboard
Hard Disk Connectors: IDE1 & IDE2
The mainboard has a 32-bit Enhanced PCI IDE and Ultra DMA 33/66/100/133 controller
that provides PIO mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 function. You
can connect up to four hard disk drives, CD-ROM, 120MB Floppy (reserved for future
BIOS) and other devices. These connectors support the provided IDE hard disk cable.
IDE1 (Primary IDE Connector)
The first hard drive should always be connected to IDE1. IDE1 can connect a Master
and a Slave drive. You must configure second hard drive to Slave mode by setting the
jumper accordingly.
IDE2 (Secondary IDE Connector)
IDE2 can also connect a Master and a Slave drive.
MSI Reminds You...
If you install two hard disks on cable, you must configure the second
drive to Slave mode by setting its jumper. Refer to the hard disk
documentation supplied by hard disk vendors for jumper setting
instructions.
IDE1IDE2
2-17
Hardware Setup
Serial ATA HDD Connectors: SATA1 & SATA2
The mainboard provides dual high-speed Serial ATA interface ports. The ports support
1st generation Serial ATA data rates of 150MB/s and are fully compliant with Serial A TA
1.0 specifications. Each Serial ATA connector can connect to 1 hard disk drive.
PIN SIGNAL PIN SIGNAL
1 GND 2 TXP
3 TXN 4 GND
5 RXN 6 RXP
7 GND
Pin Definition
Connect to SATA1 or SATA2
Take out the dust cover and
connect to the hard disk
devices
Optional Serial A TA cable
MSI Reminds You...
Please do not fold the Serial ATA cable into 90-degree angle. Otherwise,
the loss of data may occur during transmission.
SATA2
SATA1
1
7
Loading...