MSD 8600 Installation

NON MAGNETIC

PICKUP

3/8" x 1 ½"

5/16" x 1 ¼"

LOCKNUT

MOUNT

RETAINER

BRACKET

PICKUP MOUNT

Flying Magnet Crank Trigger Kit

Chevrolet Small Block Engine with 6¼” Damper

PN 8600

ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team create new products that you ask for! Go to www.msdperformance.com/registration.

Important: Read the instructions before attempting the installation.

Parts Included:

1 - Bracket

1 - Trigger Wheel 1 - Pickup Mount 1 - Centering Ring 1 - Non Magnetic Pickup Assembly 1 - Mount Retainer

Note: On some vehicles the MSD Crank Trigger Kit may require slight modiﬁcations to accommodate

special engine plates, pulley systems, etc.

INSTALLING THE PICKUP AND BRACKET

1 - Locknut 2 - Bolts, 3/8" - 16 x 1.5" 2 - Bolts, 5/16" - 18 x 1.25” 3 - Bolts, 3/8" - 24 x 1” 2 - 5/16" Washers

1. Install the pickup mount onto the bracket using the two 5/16" bolts (Figure 1). The mount retainer will only install one way, do not try to force the bolts in. Hand tighten the bolts.

2. Install the bracket onto the engine. The bracket can only be mounted on the passenger side of the engine. Be sure to use the correct length bolts in the proper location.

3. Install the pickup into the holder followed by the locknut. Do not tighten the locknut at this time.

INSTALLING THE TRIGGER WHEEL

Figure 1 Pickup Bracket Assembly.

The trigger wheel is designed so it can be used on engines with a dry sump oiling system as well as stock dampers. Two centering rings are included; one for use on stock or most aftermarket dampers and one for use with a dry sump pump drive mandrel (Figure 2).

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

Note: A centering ring must be used in all

applications. Do not rely on the bolts to center the trigger wheel accurately.

Figure 2 Centering Ring Installation.

1. Position the number one cylinder under compression at the desired total timing.

2. Install the trigger wheel centering ring onto the trigger wheel (Figure 2).

3. Position the trigger wheel onto the harmonic balancer and centering ring so one of the four magnets lines up with the center of the non-magnetic pickup. Make sure the wheel is mounted so it rotates in the direction of the arrow on the wheel. If necessary, slide the pickup in its mount until it properly lines up with the trigger wheel magnet.

4. Check and make sure the wheel is positioned correctly with the pickup and torque the trigger wheel bolts to 25 - 30 lbft. The pickup should be centered to the center line of the trigger wheel (Figure 3). If not, it may be necessary to add or delete shims to the pickup bracket to achieve the proper position.

Figure 3 Pickup Centered on

the Trigger Wheel.

Service

In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty.

When returning MSD components for warranty service, Proof of Purchase must be supplied for veriﬁcation. After the warranty period has expired, repair service is based on a minimum and maximum fee.

All returns must have a Return Material Authorization (RMA) number issued to them before

being returned. To obtain an RMA number please contact MSD Customer Service at 1 (888) MSD-7859 or visit our website at www.msdperformance.com/rma to automatically obtain a number and shipping information.

When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include a detailed account of any problems experienced, and what components and accessories are installed on the vehicle. The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered by warranty). For more information, call MSD at (915) 855-7123. MSD technicians are available from 7:00 a.m. to 5:00 p.m. Monday - Friday (mountain time).

Limited Warranty

SD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date of the original purchase. This warranty is void for any products purchased through auction websites. If found to be defective as mentioned above, it will be repaired or replaced at the option of MSD. Any item that is covered under this warranty will be returned free of charge using Ground shipping methods. This shall constitute the sole remedy of the purchaser and the sole liability of MSD. To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, including any implied warranty of merchantability or ﬁtness. In no event shall MSD or its suppliers be liable for special or consequential damages. *Intended normal use means that this item is being used as was originally intended and for the original application as sold by MSD. Any modiﬁcations to this item or if it is used on an application other than what MSD markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item will work for the application they are intending. MSD will accept no liability for custom applications.

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

FRM29793 Revised 01/12 Printed in U.S.A.