MSD 8366 Installation

Pro-Billet Late Model GM Distributor,

V8-PN 8366*, V6-PN 8367

ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team create new products that you ask for! Go to www.msdperformance.com/registration.

* The PN 8366, V8 Distributor is U.L. approved for marine applications.

Parts Included: Replacement Parts:

1 - Distributor V8 Cap - PN 8426 1 - Gear Lubricant V8 Rotor - PN 8427 1- Gasket Gear - PN 8531

WARNING: During installation disconnect the battery cables. When disconnecting the

battery, always remove the negative cable ﬁrst and install it last.

These Pro-Billet Distributors are designed as direct replacements for most GM V8 and 4.3L V6 engines with factory fuel injection systems and a remote, dual connector coil.

REMOVAL

1. Remove the existing distributor cap without disconnecting any spark plug wires.

2. With the cap off, turn the engine over until the rotor is aimed at a ﬁxed point on the engine or ﬁrewall. Note this position by making a mark (Figure 1).

3. Place the distributor cap back on and note which plug wire the rotor is pointing at. Mark the spark plug wires and remove the cap.

4. Disconnect the two connectors from the distributor’s ignition module.

5. Loosen the distributor hold-down clamp and slide it out of the way.

6. Lift the distributor out of the engine. Note that the rotor rotates as you lift it out. This is due to the helical cut gear and should be taken into consideration when installing the new distributor.

INSTALLATION

Figure 1 Marking the Distributor Location.

Note: There are two O-Ring grooves on the housing. The supplied O-rings can only be used if the

block has been modiﬁed as shown in Figure 2.

1. Remove the cap from the MSD distributor. Install the new gasket on the housing.

2. Apply a liberal amount of the supplied break-in lubricant to the distributor gear.

3. Install the distributor making sure that the rotor comes to rest at the ﬁxed mark. If the distributor

will not fully seat you may need to rotate the oil pump shaft.

4. With the rotor in the correct position and the distributor fully seated, install the distributor clamp

and tighten it.

5. Connect the two wiring harnesses.

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

6. Install the distributor cap and install the spark plug wires one at a time to ensure correct location. Chevrolet V8 ﬁring order is: 1-8-4-3-6-5-7-2. The V6 ﬁring order is 1-6-5-4-3-2.

7. You will need to check the ignition timing to get it to exact speciﬁcations. To check the timing you need to disconnect the single wire "EST" connector. Follow the recommended procedure which should be outlined on the Emission Speciﬁcation Decal in the engine compartment.

Note: When you disconnect the EST, the

Figure 2 Modiﬁed Block for use with O-Rings.

Check Engine Light will illuminate and a code will set. When the vehicle is shut off and the connector is plugged back in, the Check Engine Light will turn off, however the code will be in the memory. The code will disappear after several start sequences. To clear the code immediately, disconnect the negative battery cable for ﬁve minutes.

Service

In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty.

When returning MSD components for warranty service, Proof of Purchase must be supplied for veriﬁcation. After the warranty period has expired, repair service is based on a minimum and maximum fee.

All returns must have a Return Material Authorization (RMA) number issued to them before

being returned. To obtain an RMA number please contact MSD Customer Service at 1 (888) MSD-7859 or visit our website at www.msdperformance.com/rma to automatically obtain a number and shipping information.

When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include a detailed account of any problems experienced, and what components and accessories are installed on the vehicle. The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered by warranty). For more information, call MSD at (915) 855-7123. MSD technicians are available from 7:00 a.m. to 5:00 p.m. Monday - Friday (mountain time).

Limited Warranty

SD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date of the original purchase. This warranty is void for any products purchased through auction websites. If found to be defective as mentioned above, it will be repaired or replaced at the option of MSD. Any item that is covered under this warranty will be returned free of charge using Ground shipping methods. This shall constitute the sole remedy of the purchaser and the sole liability of MSD. To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, including any implied warranty of merchantability or ﬁtness. In no event shall MSD or its suppliers be liable for special or consequential damages. *Intended normal use means that this item is being used as was originally intended and for the original application as sold by MSD. Any modiﬁcations to this item or if it is used on an application other than what MSD markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item will work for the application they are intending. MSD will accept no liability for custom applications.

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

FRM28663 Revised 01/12 Printed in U.S.A.